aboutsummaryrefslogtreecommitdiff
path: root/drivers/ata/sata_mv.c
AgeCommit message (Collapse)Author
2008-07-04sata_mv: safer logic for limit_warningsMark Lord
There is a miniscule chance that two separate host controllers might be in sata_mv at the same time and manage to decrement the static limit_warnings variable below zero. Fix the comparison to deal with it. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-18sata_mv: warn on PIO with multiple DRQsMark Lord
Chip errata sometimes prevents reliable use of PIO commands which involve more than a single DRQ (data request). In normal operation, libata should not generate such PIO commands (uses DMA instead), but they could be sent in via SG_IO from userspace. A full workaround might be to break up such commands into sequences of single DRQ ones, but that's just way too complex for something that doesn't normally happen in real life. So, allow the attempt (it often works, despite the errata), but log the event for reference when somebody screams. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-18sata_mv: enable async_notify for 60x1 Rev.C0 and higherMark Lord
The early chipsets cannot safely handle Async Notification (AN), but 6041/6081 chip revision "C0" (and newer) can handle it. So allow AN for "C0" and higher. This enables use of hotplug on PMP ports for the 6041/6081 PCI Rev.9 chips. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-04sata_mv: PHY_MODE4 cleanupsMark Lord
The handling for PHY_MODE4 was originally just cloned from the Marvell proprietary driver (with their blessing). But we can do better than that. Tidy things up with some judicious mask definitions, to improve maintainability. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-30sata_mv: implement SoC guideline SATA_S11Mark Lord
The 5182 System-On-Chip (SOC) variant wants certain lower bits to be cleared on any write to the PHY_MODE3 register. If/when support is added for other SOC variants, we'll need some way to uniquely identify the 5182, and not perform this workaround for the others. But for now, it is the only SOC variant we support here. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-30sata_mv: workaround for 60x1 errata sata13Mark Lord
The "B2" variant of the 6041/6081 (genII) chips requires that the PHY_MODE3 register be rewritten after any write to PHY_MODE4. This fixes a regression introduced by an earlier patch. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-30sata_mv: nuke unreleased GenIIe revisionsMark Lord
The only public release of the 6042/7042 chips was/is revision "B0". Remove code that attempted to deal with earlier, non-released revs. This matches the logic of the current Marvell "proprietary" driver. Also, bump up the sata_mv version number, to reflect this batch of erratas. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-30sata_mv: PHY_MODEx errata fixesMark Lord
Fix and update the errata handling for the PHY_MODEx registers. This improves receiver noise tolerance, among other things. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-30sata_mv: move SOC_FLAG to hprivMark Lord
Convert the System-on-Chip flag from a host flag to an hpriv flag, for better consistency with other chip-rev flags, and for easier use in errata fixes etc. Also change the related "HAS_PCI()" into "!IS_SOC()" for better consistency of naming/use (everything else SOC-related already uses "SOC"). There are no functionality changes in this patch. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19sata_mv: ensure empty request queue for FBS-NCQ EHMark Lord
Check for an empty request queue before stopping EDMA after a FBS-NCQ error, as per recommendation from the Marvell datasheet. This ensures that the EDMA won't suddenly become active again just after our subsequent check of the empty/idle bits. Also bump DRV_VERSION. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19sata_mv: cache main_irq_mask register in hprivMark Lord
Part five of simplifying/fixing handling of the main_irq_mask register to resolve unexpected interrupt issues observed in 2.6.26-rc*. Keep a cached copy of the main_irq_mask so that we don't have to stall the CPU to read it on every pass through mv_interrupt. This significantly speeds up interrupt handling, both for sata_mv, and for any other driver/device sharing the same PCI IRQ line. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19sata_mv: disregard masked irqsMark Lord
Part four of simplifying/fixing handling of the main_irq_mask register to resolve unexpected interrupt issues observed in 2.6.26-rc*. Ignore masked IRQs in mv_interrupt(). This prevents "unexpected device interrupt while idle" messages. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19sata_mv: fix pmp drives not foundMark Lord
Part three of simplifying/fixing handling of the main_irq_mask register to resolve unexpected interrupt issues observed in 2.6.26-rc*. Partially fix a reported bug whereby we sometimes miss seeing drives on a port-multiplier, as reported by Gwendal Grignou <gwendal@google.com>. The problem was that we were receiving unexpected interrupts during EH from POLLed commands while accessing port-multiplier registers. These unexpected interrupts can be prevented by masking the DONE_IRQ bit for the port whenever not operating in EDMA mode. Also fix port_stop() to mask all port interrupts. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19sata_mv: consolidate main_irq_mask updatesMark Lord
Part two of simplifying/fixing handling of the main_irq_mask register to resolve unexpected interrupt issues observed in 2.6.26-rc*. Consolidate all updates of the host main_irq_mask register into a single function. This simplifies maintenance, and also prepares the way for caching it (later). No functionality changes in this update. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19sata_mv: don't blindly enable IRQsMark Lord
Part one of simplifying/fixing handling of the main_irq_mask register to resolve unexpected interrupt issues observed in 2.6.26-rc*. Don't blindly enable port IRQs at host init time. Instead, enable only the bits that we want, which in this case is simply the PCI_ERR bit. The per-port bits can wait until the ports are reset/probed for devices. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19sata_mv: async notify for genIIe onlyMark Lord
Now that we handle the FIS_IRQ_CAUSE register correctly, we can also now handle SATA asynchronous notification events. So enable them, but only for the more modern GenIIe chips. (older chips have unaddressed errata issues related to this). This fixes hot plug/unplug for port-muliplier ports. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19sata_mv: group genIIe flagsMark Lord
Group all of the flags for GenIIe devices into a common definition, to ensure that any updates to them are shared by all GenIIe devices. This will help make future maintenance somewhat simpler. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19sata_mv: fis irq register fixesMark Lord
Fix handling of the FIS_IRQ_CAUSE register in sata_mv. This register exists *only* on GenIIe devices, so don't bother writing to it on older chips. Also, it has to be read/cleared in mv_err_intr() before clearing the main ERR_IRQ_CAUSE register. This keeps sata_mv from getting stuck forever on certain error types. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19sata_mv: always do softresetMark Lord
Always request a softreset after hardreset succeeds. This fixes a regression reported by Martin Michlmayr <tbm@cyrius.com>. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06sata_mv use hweight16() for bit counting (V2)Mark Lord
Some tidying as suggested by Grant Grundler. Nuke local bit-counting function from sata_mv in favour of using hweight16(). Also add a short explanation for the 15msec timeout used when waiting for empty/idle. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06sata_mv NCQ-EH for FIS-based switchingMark Lord
Convert sata_mv's EH for FIS-based switching (FBS) over to the sequence recommended by Marvell. This enables us to catch/analyze multiple failed links on a port-multiplier when using NCQ. To do this, we clear the ERR_DEV bit in the EDMA Halt-Conditions register, so that the EDMA engine doesn't self-disable on the first NCQ error. Our EH code sets the MV_PP_FLAG_DELAYED_EH flag to prevent new commands being queued while we await completion of all outstanding NCQ commands on all links of the failed PM. The SATA Test Control register tells us which links have failed, so we must only wait for any other active links to finish up before we stop the EDMA and run the .error_handler afterward. The patch also includes skeleton code for handling of non-NCQ FBS operation. This is more for documentation purposes right now, as that mode is not yet enabled in sata_mv. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06sata_mv delayed eh handlingMark Lord
Introduce a new "delayed error handling" mechanism in sata_mv, to enable us to eventually deal with multiple simultaneous NCQ failures on a single host link when a PM is present. This involves a port flag (MV_PP_FLAG_DELAYED_EH) to prevent new commands being queued, and a pmp bitmap to indicate which pmp links had NCQ errors. The new mv_pmp_error_handler() uses those values to invoke ata_eh_analyze_ncq_error() on each failed link, prior to freezing the port and passing control to sata_pmp_error_handler(). This is based upon a strategy suggested by Tejun. For now, we just implement the delayed mechanism. The next patch in this series will add the multiple-NCQ EH code to take advantage of it. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06sata_mv new mv_port_intr functionMark Lord
Separate out the inner loop body of mv_host_intr() into it's own function called mv_port_intr(). This should help maintainabilty. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06sata_mv fix mv_host_intr bug for hc_irq_causeMark Lord
Remove the unwanted reads of hc_irq_cause from mv_host_intr(), thereby removing a bug whereby we were not always reading it when needed.. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06sata_mv NCQ and SError fixes for mv_err_intrMark Lord
Sigh. Undo some earlier changes to mv_port_intr(), so that we now read/clear SError again in all cases. Arrange the top of the function to be as close as possible to what we need for a later update (in this series) for ERR_DEV handling. Fix things so that libata-eh can attempt a READ_LOG_EXT_10H in response to a failed NCQ command, by just doing a local mv_eh_freeze() rather than ata_port_freeze(). This will now fully handle NCQ errors much of the time, but more fixes are needed for FBS/PMP, and for certain chip errata. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06sata_mv rearrange mv_config_fbsMark Lord
Rearrange mv_config_fbs() to more closely follow the (corrected) datasheet recommendations for NCQ and FIS-based switching (FBS). Also, maintain a port flag to let us know when FBS is enabled. We will make more use of that flag later in this patch series. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06sata_mv errata workaround for sata25 part 1Mark Lord
Part 1 of workaround for errata "sata#25" for the 60x1 series (the second half of this errata workaround is still in development. Bit22 of the GPIO port has to be set "on" when in NCQ mode. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06sata_mv new mv_qc_defer methodMark Lord
The EDMA engine cannot tolerate a mix of NCQ/non-NCQ commands, and cannot be used for PIO at all. So we need to prevent libata from trying to feed us such mixtures. Introduce mv_qc_defer() for this purpose, and use it for all chip versions. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06sata_mv wait for empty+idleMark Lord
When performing EH, it is recommended to wait for the EDMA engine to empty out requests-in-progress before disabling EDMA. Introduce code to poll the EDMA_STATUS register for idle/empty bits before disabling EDMA. For non-EH operation, this will normally exit without delay, other than the register read. A later series of patches may focus on eliminating this and various other register reads (when possible) throughout the driver, but for now we're focussing on solid reliablity. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06sata_mv pci featuresMark Lord
Some of the GenIIe EDMA optimizations should not be used for non-PCI (SOC) devices, and nor for certain configurations of conventional PCI (non PCI-X, PCIe) buses. Logic taken/simplified from that in the Marvell proprietary driver. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06sata_mv more cosmetic changesMark Lord
More cosmetic changes; no code changes. -- try and improve consistency of naming. -- add missing _OFS to tails of register offset definitions. -- rename mv_setup_ifctl() to mv_setup_ifcfg(), since that's what it really does. -- remove/move some dead comments Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-29sata_mv: Improve naming of main_irq cause/mask identifiersMark Lord
Tidy up naming of things associated with the PCI / SOC chip "main irq cause/mask" registers, as inspired by Jeff. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25sata_mv: re-enable hotplug, update TODO listMark Lord
Re-enable hotplug, now that the interrupt/error handling are mostly sane. Also update the TODO list at the top. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25sata_mv: leave SError bits untouched in mv_err_intrMark Lord
Here it is again, minus the checkpatch.pl complaint: Rework mv_err_intr() to leave the SError bits as-is, so that libata-eh has a chance to see/use them. We originally thought that clearing them here was necessary before writing back to edma_err_cause (per the Marvell datasheets), but we will end up reseting the chip regardless in those cases. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25sata_mv: more interrupt handling reworkMark Lord
Continue fixing the interrupt handling logic. Get rid of mv_intr_pio(), by using ata_sff_host_intr() for PIO.. Add a mv_unexpected_intr() catch-all for "impossible" scenarios, where we get an interrupt that shouldn't have happened (never seen in testing, but just in case..). Rearrange the logic so that we always process completed response queue entries before looking for other events, This avoids having to re-issue commands that had already succeeded. As part of this, we split out some duplicated functionality into a new function, mv_get_active_qc(). Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25sata_mv: tidy host controller interrupt handlingMark Lord
Tidy up host controller interrupt handling, by moving the weirdo bit shifting from mv_interrupt() to mv_host_intr(). This lets us take advantage of the MV_PORT_TO_SHIFT_AND_HARDPORT() macro from an earlier patch to greatly simplify the port numbering logic. Also, defer reading the hc_irq_cause (one per hc) until it is actually proven to be needed. This may save a microsecond or so per interrupt, on average (a later patchset will further reduce unnecessary register reads throughout the driver). Apart from that, we still leave the actual IRQ handling logic alone. Subsequent patches in this series will address that. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25sata_mv: simplify request/response queue handlingMark Lord
Try and simplify handling of the request/response queues. Maintain the cached copies of queue indexes in a fully-masked state, rather than having each use of them have to do the masking. Split off handling of a single crpb response into a separate function, to reduce complexity in the main mv_process_crpb_entries() routine. Ignore the rarely-valid error bits from the crpb status field, as we already handle that information in mv_err_intr(). For now, preserve the rest of the original logic. A later patch will deal with fixing that separately. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25sata_mv: simplify freeze/thaw bit-shift calculationsMark Lord
Introduce the MV_PORT_TO_SHIFT_AND_HARDPORT() macro, to centralize/simplify various scattered bits of logic for calculating bit shifts and the like. Some of the places that do this get it wrong, too, so consolidating the algorithm at one place will help keep the code correct. For now, we use the new macro in mv_eh_{freeze,thaw}. A subsequent patch will re-use this in the interrupt handlers Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25sata_mv mask all interrupt coalescing bitsMark Lord
Ignore *all* interrupt coalescing bits on all controllers, not just some of each. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25sata_mv more cosmeticsMark Lord
More cosmetic cleanups prior to the interrupt/error handling logic changes. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-19Merge branch 'merge-fixes' into develRussell King
2008-04-17sata_mv add temporary 3 second init delay for SiliconImage PMsMark Lord
sata_mv does not yet fully support hotplug (coming soon, though). This means that the driver may not find a Silicon Image port-multiplier when first loaded, because those devices take in exceess of 3 seconds to sync up the SATA PHY (most devices do this in mere microseconds). So, as a short-term interim measure, here we insert a 3-second pause on initial driver load, once per controller board (not once per port!), to allow the Silicon Image port-multipliers to be detected later. This will be removed again (soon!) once hotplug is fully implemented/working. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17sata_mv remove redundant edma init codeMark Lord
Remove unnecessary edma init code from port_start. This sequence gets done later on the first I/O to the port. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17sata_mv add basic port multiplier supportMark Lord
Add basic port-multiplier support to sata_mv. This works in Command-based-switching mode for Gen-II chipsets, and in FIS-based-switching mode for Gen-IIe chipsets. Error handling remains at the primary port level for now (works okay, but not great). This will get fixed in a subsequent patch series for IRQ/EH handling fixes. There are also some known NCQ/PMP errata to be dealt with in the near future, once we have this basic PMP support in place. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17sata_mv fix SOC flags, enable NCQ on SOCMark Lord
The System-On-Chip (SOC) core supports all of the same features as the other recent Marvell chips, including NCQ and IRQ coalescing. Fix the chip_soc flags to enable these capabilities (note that the driver currently does nothing special for IRQ coalescing, though). Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17sata_mv disable hotplug for nowMark Lord
Disable hot plug/unplug detection in sata_mv for now. It is currently broken, and also interferes with PMP support. This will get fixed in a subsequent patch series. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17sata_mv cosmeticsMark Lord
More cosmetic cleanups to unclutter the changes needed for PMP support. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17sata_mv hardreset reworkMark Lord
Rework and simplify sata_mv's hardreset code to take advantage of libata improvements since it was first coded. Also, get rid of the now unnecessary prereset, postreset, and phy_reset functions. This patch also paves the way for subsequent pmp support patches, which will follow once this one passes muster. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17libata: rename SFF functionsTejun Heo
SFF functions have confusing names. Some have sff prefix, some have bmdma, some std, some pci and some none. Unify the naming by... * SFF functions which are common to both BMDMA and non-BMDMA are prefixed with ata_sff_. * SFF functions which are specific to BMDMA are prefixed with ata_bmdma_. * SFF functions which are specific to PCI but apply to both BMDMA and non-BMDMA are prefixed with ata_pci_sff_. * SFF functions which are specific to PCI and BMDMA are prefixed with ata_pci_bmdma_. * Drop generic prefixes from LLD specific routines. For example, bfin_std_dev_select -> bfin_dev_select. The following renames are noteworthy. ata_qc_issue_prot() -> ata_sff_qc_issue() ata_pci_default_filter() -> ata_bmdma_mode_filter() ata_dev_try_classify() -> ata_sff_dev_classify() This rename is in preparation of separating SFF support out of libata core layer. This patch strictly renames functions and doesn't introduce any behavior difference. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17sata_mv fix ifctl handlingMark Lord
Fix handling of the SATA_INTERFACE_CFG register to match datasheet requirements. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>