| Age | Commit message (Collapse) | Author |
|---|
|
Error found by Jeff Haran.
The error detect register is 0s when no errors are detected. The check
code is incorrect, so reverse check sense.
Reported-by: Jeff Haran <jharan@Brocade.COM>
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The edac-core driver includes code which assumes that the work_struct
which is included in every delayed_work is the first member of that
structure. This is currently the case but might change in the future, so
use to_delayed_work() instead, which doesn't make such an assumption.
linux-2.6.30-rc1 has the to_delayed_work() function that will allow this
patch to work
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix the edac local pci_write_bits32 to properly note the 'escape' mask if
all ones in a 32-bit word.
Currently no consumer of this function uses that mask, so there is no
danger to existing code.
Signed-off-by: Jeff Haran <jharan@Brocade.COM>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Introduce Kconfig and Makefile options for AMD8111 EDAC driver.
Signed-off-by: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Introduce Kconfig and Makefile options for AMD8131 EDAC driver.
Signed-off-by: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Introduce AMD8131 EDAC driver source file, which makes use of error
detections on the PCI-X Bridge Controllers on the AMD8131 HyperTransport
PCI-X Tunnel.
Signed-off-by: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Introduce AMD8131 EDAC driver header file, which adds register and bits
definitions for the PCI-X Bridge Controller on the AMD8131 HyperTransport
I/O Hub.
Signed-off-by: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add edac_pci_alloc_index(), because for MAPLE platform there may exist
several EDAC driver modules that could make use of edac_pci_ctl_info
structure at the same time. The index allocation for these structures
should be taken care of by EDAC core.
Signed-off-by: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Introduce AMD8111 EDAC driver source file, which makes use of error
detections on the LPC Bridge Controller and PCI Bridge Controller on the
AMD8111 HyperTransport I/O Hub.
Signed-off-by: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Introduce AMD8111 EDAC driver header file, which adds register and bits
definitions for the LPC Bridge Controller and PCI Bridge Controller on the
AMD8111 HyperTransport I/O Hub.
Signed-off-by: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This adds support for an EDAC memory controller adaptation driver for the
"ibm,sdram-4xx-ddr2" ECC controller realized in the AMCC PowerPC 405EX[r].
At present, this driver has been developed and tested against the
controller realization in the AMCC PPC405EX[r] on the AMCC Kilauea and
Haleakala boards (256 MiB w/o ECC memory soldered onto the board) and a
proprietary board based on those designs (128 MiB ECC memory, also
soldered onto the board).
In the future, dynamic feature detection and handling needs to be added
for the other realizations of this controller found in the 440SP, 440SPe,
460EX, 460GT and 460SX.
Eventually, this driver will likely be evolved and adapted to the above
variant realizations of this controller as well as broken apart to handle
the other known ECC-capable controllers prevalent in other PPC4xx
processors:
- IBM SDRAM (405GP, 405CR and 405EP) "ibm,sdram-4xx"
- IBM DDR1 (440GP, 440GX, 440EP and 440GR) "ibm,sdram-4xx-ddr"
- Denali DDR1/DDR2 (440EPX and 440GRX) "denali,sdram-4xx-ddr2"
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Grant Erickson <gerickson@nuovations.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
After 3 years, this is a patch to remove the EXPERIMENTAL tag on EDAC. We
now have many module drivers submitters in EDAC and believe EDAC is no
longer EXPERIMENTAL
Signed-off-by: Doug Thompson <dougthompson@xmission.com
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
A patch for making a debugging information more verbose for use in
development debugging.
By enabling the new option "More verbose debugging", information about
source file and line number will be added to debugging message.
This is sample output,
EDAC MC0: Giving out device to 'e7xxx_edac' 'E7205': DEV 0000:00:00.0
EDAC DEBUG: in drivers/edac/edac_pci.c, line at 48: edac_pci_alloc_ctl_info()
EDAC DEBUG: in drivers/edac/edac_pci.c, line at 334: edac_pci_add_device()
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Signed-off-by: Hitoshi Mitake <h.mitake@gmail.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Cc: dougthompson@xmission.com
Cc: bluesmoke-devel@lists.sourceforge.net
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
|
|
These are all powerpc specific drivers.
res.start in fsl_elbc_nand.c needs to be cast since it may be either 32
or 64 bit. Thanks to Scott Wood for noticing.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Arnd Bergmann <arnd@arndb.de> call_edac bits in particular
Acked-by: Olof Johansson <olof@lixom.net> pasemi_nand peices
Acked-by: Scott Wood <scottwood@freescale.com> fsl_elbc fixes
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Signed-off-by: Ben Woodard <woodard@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
EDAC driver for i5400 MCH (Seaburg)
This driver adds support for i5400 MCH chipset.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Ben Woodard <woodard@redhat.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
All other compatibles that are uniquely identifying the processor use a
prefix of the form fsl,mpc85...'. We add support for it so we can
deprecate the older 'fsl,85...' that was improperly used here.
Additionally added mpc8536 & mpc8560 to the compatible lists.
This patch is based on Nate's 8572 patch.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Acked-by: Dave Jiang <djiang@mvista.com>
Cc: Nate Case <ncase@xes-inc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch is part of a larger patch series which will remove the "char
bus_id[20]" name string from struct device. The device name is managed in
the kobject anyway, and without any size limitation, and just needlessly
copied into "struct device".
[akpm@linux-foundation.org: coding-style fixes]
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Use the newly introduced pci_ioremap_bar() function in drivers/edac.
pci_ioremap_bar() just takes a pci device and a bar number, with the goal
of making it really hard to get wrong, while also having a central place
to stick sanity checks.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (144 commits)
powerpc/44x: Support 16K/64K base page sizes on 44x
powerpc: Force memory size to be a multiple of PAGE_SIZE
powerpc/32: Wire up the trampoline code for kdump
powerpc/32: Add the ability for a classic ppc kernel to be loaded at 32M
powerpc/32: Allow __ioremap on RAM addresses for kdump kernel
powerpc/32: Setup OF properties for kdump
powerpc/32/kdump: Implement crash_setup_regs() using ppc_save_regs()
powerpc: Prepare xmon_save_regs for use with kdump
powerpc: Remove default kexec/crash_kernel ops assignments
powerpc: Make default kexec/crash_kernel ops implicit
powerpc: Setup OF properties for ppc32 kexec
powerpc/pseries: Fix cpu hotplug
powerpc: Fix KVM build on ppc440
powerpc/cell: add QPACE as a separate Cell platform
powerpc/cell: fix build breakage with CONFIG_SPUFS disabled
powerpc/mpc5200: fix error paths in PSC UART probe function
powerpc/mpc5200: add rts/cts handling in PSC UART driver
powerpc/mpc5200: Make PSC UART driver update serial errors counters
powerpc/mpc5200: Remove obsolete code from mpc5200 MDIO driver
powerpc/mpc5200: Add MDMA/UDMA support to MPC5200 ATA driver
...
Fix trivial conflict in drivers/char/Makefile as per Paul's directions
|
|
When deleting an edac device, we have to wait for its edac_dev.work to be
completed before deleting the whole edac_dev structure. Since we have no
idea which work in current edac_poller's workqueue is the work we are
conerned about, we wait for all work in the edac_poller's workqueue to be
proceseed. This is done via flush_cpu_workqueue() which inserts a
wq_barrier into the tail of the workqueue and then sleeping on the
completion of this wq_barrier. The edac_poller will wake up sleepers when
it is found.
EDAC core creates only one kernel worker thread, edac_poller, to run the
works of all current edac devices. They share the same callback function
of edac_device_workq_function(), which would grab the mutex of
device_ctls_mutex first before it checks the device. This is exactly
where edac_poller and rmmod would have a great chance to deadlock.
In below call trace of rmmod > ... >
edac_device_del_device >
edac_device_workq_teardown > flush_workqueue > flush_cpu_workqueue,
device_ctls_mutex would have already been grabbed by
edac_device_del_device(). So, on one hand rmmod would sleep on the
completion of a wq_barrier, holding device_ctls_mutex; on the other hand
edac_poller would be blocked on the same mutex when it's running any one
of works of existing edac evices(Note, this edac_dev.work is likely to be
totally irrelevant to the one that is being removed right now)and never
would have a chance to run the work of above wq_barrier to wake rmmod up.
edac_device_workq_teardown() should not be called within the critical
region of device_ctls_mutex. Just like is done in edac_pci_del_device()
and edac_mc_del_mc(), where edac_pci_workq_teardown() and
edac_mc_workq_teardown() are called after related mutex are released.
Moreover, an edac_dev.work should check first if it is being removed. If
this is the case, then it should bail out immediately. Since not all of
existing edac devices are to be removed, this "shutting flag" should be
contained to edac device being removed. The current edac_dev.op_state can
be used to serve this purpose.
The original deadlock problem and the solution have been witnessed and
tested on actual hardware. Without the solution, rmmod an edac driver
would result in below deadlock:
root@localhost:/root> rmmod mv64x60_edac
EDAC DEBUG: mv64x60_dma_err_remove()
EDAC DEBUG: edac_device_del_device()
EDAC DEBUG: find_edac_device_by_dev()
(hang for a moment)
INFO: task edac-poller:2030 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
edac-poller D 00000000 0 2030 2
Call Trace:
[df159dc0] [c0071e3c] free_hot_cold_page+0x17c/0x304 (unreliable)
[df159e80] [c000a024] __switch_to+0x6c/0xa0
[df159ea0] [c03587d8] schedule+0x2f4/0x4d8
[df159f00] [c03598a8] __mutex_lock_slowpath+0xa0/0x174
[df159f40] [e1030434] edac_device_workq_function+0x28/0xd8 [edac_core]
[df159f60] [c003beb4] run_workqueue+0x114/0x218
[df159f90] [c003c674] worker_thread+0x5c/0xc8
[df159fd0] [c004106c] kthread+0x5c/0xa0
[df159ff0] [c0013538] original_kernel_thread+0x44/0x60
INFO: task rmmod:2062 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
rmmod D 0ff2c9fc 0 2062 1839
Call Trace:
[df119c00] [c0437a74] 0xc0437a74 (unreliable)
[df119cc0] [c000a024] __switch_to+0x6c/0xa0
[df119ce0] [c03587d8] schedule+0x2f4/0x4d8
[df119d40] [c03591dc] schedule_timeout+0xb0/0xf4
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Since the QPACE (Chromodynamics Parallel Computing on the
Cell Broadband Engine) platform doesn't use a iommu, doesn't
have PCI devices and a MPIC much lesser setup and
configurations are needed. So far all devices are detected
as OF device. A notifier function is used to set the dma_ops
for the of_platform bus. Further this patch splits the
PPC_CELL_NATIVE into PPC_CELL_COMMON which are parts that are
shared with the QPACE platform and the rest.
Signed-off-by: Benjamin Krill <ben@codiert.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Fix module removal bugs of i82875p_edac. Also i82975x_edac code seems to
have the same module removal bugs as in i82875p_edac.
The problems were:
1. In module removal i82875p_remove_one() is never called.
Variable i82875p_registered is newer changed from 1, which
guarantees i82875p_remove_one() is not called (and even if it were
called, it would be called in wrong order).
As a result, the edac_mc workque is not stopped and keeps probing.
If kernel debugging options are not enabled, user may not notice
anything going wrong.
if debugging options are enabled and I do "rmmod i82875p_edac", I
get:
edac debug: edac_pci_workq_function() checking
BUG: unable to handle kernel paging request at f882d16f
...
call trace:
[<f8834df3>] ? edac_mc_workq_function+0x55/0x7e [edac_core]
[<c0233974>] ? run_workqueue+0xd7/0x1a5
[<c023392f>] ? run_workqueue+0x92/0x1a5
[<f8834d9e>] ? edac_mc_workq_function+0x0/0x7e [edac_core]
[<c0233af9>] ? worker_thread+0xb7/0xc3
[<c0236a7b>] ? autoremove_wake_function+0x0/0x33
[<c0233a42>] ? worker_thread+0x0/0xc3
[<c0236809>] ? kthread+0x3b/0x61
[<c02367ce>] ? kthread+0x0/0x61
[<c0204587>] ? kernel_thread_helper+0x7/0x10
Fix for this is to get rid of needles variable i82875p_registered
altogether and run i82875p_remove_one() *before*
pci_unregister_driver().
2. edac_mc_del_mc() uses mci after freeing mci
edac_mc_del_mc() calls calls edac_remove_sysfs_mci_device(). The
kobject refcount of mci drops to 0 and mci is freed. After this
mci is accessed via debug print and i82875p_remove_one() still
uses mci->pvt and tries to free mci again with edac_mc_free().
The fix for this is add kobject_get(&mci->edac_mci_kobj) after
edac_mc_alloc(). Then the mci is still available after returning
from edac_mc_del_mc() with refcount 1, and mci->pvt is still
available. When i82875p_remove_one() finally calls edac_mc_free(),
this will cause kobject_put() and mci is released properly.
Signed-off-by: Jarkko Lavinen <jlavi@iki.fi>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When I do "modprobe i82875p_edac" on my Asus P4C800 MB on kernels 2.6.26
or later, the module load fails due to BAR 0 collision. On 2.6.25 the
module loads just fine.
The overflow device on the MB seems to be hidden and its resources are not
allocated at normal PCI bus init. Log shows the missing resource problem:
EDAC DEBUG: i82875p_probe1()
PCI: 0000:00:06.0 reg 10 32bit mmio: [fecf0000, fecf0fff]
pci 0000:00:06.0: device not available because of BAR 0
[0xfecf0000-0xfecf0fff] collisions
EDAC i82875p: i82875p_setup_overfl_dev(): Failed to enable overflow
device
The patch below fixes this by calling pci_bus_assign_resources() after
the overflow device is revealed and added to the bus. With this patch
I am again able to load and use the module.
Signed-off-by: Jarkko Lavinen <jlavi@iki.fi>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
It turns out that edac_mc_del_mc will kobject_put the last kref on the
mci object.
If the timing is just right, that means that the mci object is freed
before before i5000_remove_one has a chance to free the resources
associated with it, causing a null pointer exceptions when unloading the
driver. Insert a kobject_{get,put} pair so that this doesn't happen.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The edac driver on cell turned out to be not enabled because of a missing
op_state. This patch introduces it. Verified to work on top of Ben's
next branch.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jens Osterkamp <jens@linux.vnet.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I wrote a new module for Intel X38 chipset. This chipset is very similar
to Intel 3200 chipset, but there are some different points, so I copyed
i3200_edac.c and modified.
This is Intel's web page describing this chipset.
http://www.intel.com/Products/Desktop/Chipsets/X38/X38-overview.htm
I've tested this new module with broken memory, and it seems to be working
well.
Signed-off-by: Hitoshi Mitake <mitake@clustcom.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The cell_edac driver is setting the edac_mode field of the csrow's to an
incorrect value, causing the sysfs show routine for that field to go out
of an array bound and Oopsing the kernel when used.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: <stable@kernel.org> [2.6.27.x, 2.6.26.x. 2.6.25.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Make the Thermal messages (temperature got past Tmid) be displayed only
once because:
1) it's the BIOS job to configure and handle the memory throttling
2) if the BIOS is broken or is aware about the condition, flooding the
system logs won't help anything.
3) According to the specification update for Intel 5000 MCHs, all the
revisions of this MCH have problems on the thermal sensors, making
not automatic (a.k.a. intelligent thermal throttling) impossible.
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Update the i5000_edac messages, making everything pass through the EDAC
(so the log controls will work) and being more specific about the errors.
Also, it makes the miscellaneous errors optional and disabled by default.
As I didn't found anywhere information about M23ERR-M26ERR
(FERR_NF_THERMAL) on FERR_NF_FBD, I'm removing them.
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This adds support for the dual-core MPC8572 processor. We have
to support making SPR changes on each core. Also, since we can
have multiple memory controllers sharing an interrupt, flag the
interrupts with IRQF_SHARED.
Signed-off-by: Andrew Kilkenny <akilkenny@xes-inc.com>
Signed-off-by: Nate Case <ncase@xes-inc.com>
Acked-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix 443BX/GX MCH suppport in a EDAC.
It makes i82443bxgx_edac coexist with intel_agp using the same approach as
several other EDAC drivers.
Tested on Intel's L443GX with redhat's 2.6.18 with whole EDAC subsystem
backported a while ago.
[root@host ~]# dmesg|grep -iE '(AGP|EDAC)'
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 440GX Chipset.
agpgart: AGP aperture is 64M @ 0xf8000000
EDAC MC: Ver: 2.1.0 Jun 27 2008
EDAC MC0: Giving out device to 'i82443bxgx_edac' 'I82443BXGX': DEV 0000:00:00.0
EDAC PCI0: Giving out device to module 'i82443bxgx_edac' controller 'EDAC PCI controller': DEV '0000:00:00.0' (POLLED)
Signed-off-by: Vladislav Bogdanov <slava@nsys.by>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch lets the files using linux/version.h match the files that
#include it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Convert PCI err device from platform to open firmware of_dev to comply
with powerpc schemes.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fixup of missing bit 0 on 64360 PCIx_ERR_MASK and errata FEr-#11 and
FEr-#16 for the 64460. Bit 0 must remain 0.
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Doug Thompson <dougthompson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Update get_property() call to use of_get_property() in order to fix compile
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Doug Thompson <dougthompson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This module harvests more than just memory errors, it also harvests
various bus and dma errors that the Chipset detects. Previously, it would
report all such errors, which would cause output to be TOO loud.
This patches therefore adds a parameter which is used to turn off
NON-MEMORY error reports by default. Or the reporting can be enabled via
the parameter
Also did code style cleanup: less than 80 characters per line rule
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The channel DIMM label does not seem to be used much in the edac code.
However, where it is used (in the core code), it is assumed to not have a
newline embedded. This leaves the sysfs file newline free which looks
funny when cat'ing it. Here we just add the trailing newline to the sysfs
chX_dimm_label output...
[Doug Thompson note: the DIMM label is one of the primary uses of EDAC.
User space daemon scripts, edac-utils@sourceforge, populate the DIMM label
fields, via /sys/devices/system/edac attributes, with the silk screen
labels of the motherboard in use. dmidecode access BIOS tables, but BIOS
tables are well known to be incorrect and useless in these respects.
edac-utils will strip off any newlines before its use of the output, when
displaying DIMM slot silk screen labels.
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Static kobjects and ksets are not supported in Linux kernel. Convert the
mc_kset from static to dynamic. This patch depends on my previous patch
to remove the module parameter attributes from mc...
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
/sys/devices/system/edac/mc has a few files which are duplicated in
/sys/module/edac_core/parameters. Now that all the functionality is
duplicated between these two locations, we remove the former kobject
attributes and update the documentation.
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When updating the edac_mc_poll_msec module parameter from the sysfs
/sys/module/edac_core/parameters/edac_mc_poll_msec file, we don't update
the workq timers. So that, if we move from a big poll time to a small
one, the small one won't take effect until the big one has timed out.
Here we provide a new module parameter set method to call out to the
update routine. This brings the /sys/module/edac_core/parameters
functionality up to that provided by the /sys/drivers/system/edac/mc sysfs
module parameter files so that we can remove them or at least link to the
/sys/module files...
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Static kobjects are not supported in linux kernel. Convert the
edac_pci_top_main_kobj from static to dynamic. This avoids the double
free of the edac_pci_top_main_kobj.name that we see on module reload of
the e752x edac driver (and probably others as well).
In addition Greg KH <greg@kroah.com> has pointed out that this code may be
cleaned up significantly. I will look at that as a follow-on patch, for
now, I just want the minimum fix to get this double-free oops bug
squashed...
Many thanks to Greg KH for his patience in showing me what the
Documentation/kobject.txt already said (oops)...
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Some code cleanliness issues found by Andrew Morton (thanks!) which should
not affect functionality, but which should help make the code more
maintainable.
In particular, we now:
* convert all #define's w/ a parameter to static inlines
* use 1UL rather than 1ULL when calculating an unsigned long
* use pci_disable_device
The resulting code is tested and seems to work fine...
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Explicitly unmask ECC errors we are interested in reporting.
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
It is possible that the BIOS did not enable ECC at boot time. We check
for that case and fail to load if it is true.
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The error mask we use to trigger ECC notifications is missing many bits of
interest. We add these bits here so that all possible ECC errors can be
reported.
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Preliminary support for the Intel 5100 MCH. CE and UE errors are reported
along with the current DIMM label information and other memory parameters.
Reasons why this is preliminary:
1) This chip has 2 independent memory controllers which, for best
perforance, use interleaved accesses to the DDR2 memory. This
architecture does not map very well to the current edac data structures
which depend on symmetric channel access to the interleaved data.
Without core changes, the best I could do for now is to map both memory
controllers to different csrows (first all ranks of controller 0, then
all ranks of controller 1). Someone much more familiar with the edac
core than I will probably need to come up with a more general data
structure to handle the interleaving and de-interleaving of the two
memory controllers.
2) I have not yet tackled the de-interleaving of the rank/controller
address space into the physical address space of the CPU. There is
nothing fundamentally missing, it is just ending up to be a lot of
code, and I'd rather keep it separate for now, esp since it doesn't
work yet...
3) The code depends on a particular i5100 chip select to DIMM mainboard
chip select mapping. This mapping seems obvious to me in order to
support dual and single ranked memory, but it is not unique and DIMM
labels could be wrong on other mainboards. There is no way to query
this mapping that I know of.
4) The code requires that the i5100 is in 32GB mode. Only 4 ranks per
controller, 2 ranks per DIMM are supported. I do not have hardware
(nor do I expect to have hardware anytime soon) for the 48GB (6 ranks
per controller) mode.
5) The serial presence detect code should be broken out into a "real"
i2c driver so that decode-dimms.pl can work.
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If correctable error occurs the syndrome code was logged as 0. This patch
lets EDAC to log a correct syndrome code to make problem investigation
easier.
Signed-off-by: Maxim Shchetynin <maxim@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
including of <asm/mpc85xx.h> causes build problems since it doesn't exist.
Also removed warning:
drivers/edac/mpc85xx_edac.c:45: warning: 'mpc85xx_ctl_name' defined but not used
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Doug Thompson <dougthompson@xmission.com>
Acked-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
