| Age | Commit message (Collapse) | Author |
|---|
|
The it87 driver doesn't follow the standard sensor type values as
documented in Documentation/hwmon/sysfs-interface. It uses value 2 for
thermistors instead of value 4. This causes "sensors" to tell the user
that the chip is setup for a transistor while it is actually setup for
a thermistor.
Using value 4 for thermistors solves the problem. For compatibility
reasons, we still accept value 2 but emit a warning message so that
users update their configuration files.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
|
|
The new-style lm78 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Upcoming changes to the I2C part of the lm78 driver will cause ISA
devices to no longer have a struct i2c_client at hand. So, we must
stop (ab)using it now.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
The LM78 detection is relatively weak, and sometimes recent Winbond
chips can be misdetected as an LM78. We have had repeated reports of
this happening. We have an explicit check against this for the ISA
access, do the same for I2C access now.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
The LM78 and LM79 can be accessed either on the I2C bus or the ISA
bus. We must not access the same chip through both interfaces. So far
we were relying on the user passing the correct ignore parameter to
skip the registration of the I2C interface as suggested by
sensors-detect, but this is fragile: the user may load the lm78
driver without running sensors-detect, and the i2c bus numbers are
not stable across reboots and hardware changes.
So, better detect alias chips in the driver directly, and skip any
I2C chip which is obviously an alias of the ISA chip. This is done
by comparing the value of 26 selected registers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Only request I/O ports 0x295-0x296 instead of the full I/O address
range. This solves a conflict with PNP resources on a few motherboards.
Also request the I/O ports in two parts (4 low ports, 4 high ports)
during device detection, otherwise the PNP resource make the request
(and thus the detection) fail.
This is the exact same fix that was applied to driver w83781d in
March 2008 to address the same problem:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=2961cb22ef02850d90e7a12c28a14d74e327df8d
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Label names ERROR1 and ERROR3 aren't exactly explicit. Change them for
better names that indicate what we are up to.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
|
|
Function RANGE_TO_REG can easily be simplified. Credits go to Herbert
Poetzl for indirectly suggesting this to me. I tested that the new
implementation returns the same result as the original implementation
for all input values.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
|
|
The new-style lm85 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
|
|
The Analog Devices and SMSC devices supported by the lm85 driver do
not have the same PWM frequency table as the National Semiconductor
devices. Add support for per-device frequency tables.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
|
|
The LM85 and compatible chips only support 8 arbitrary PWM frequencies.
The algorithm to pick one of them based on the user input is not
optimum. Improve it to always pick the closest supported frequency.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
|
|
Implement the standard PWM frequency interface: pwm[1-*]_freq in
units of 1 Hz, instead of the non-standard pwm[1-*]_auto_pwm_freq
in units of 0.1 Hz. The old naming was not only non-standard, it was
also confusing, because it suggested that the frequency value only
applied in automatic fan speed mode, which isn't true.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
|
|
Rework the device detection to make it clearer and faster in the
general case (when a known device is found.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
|
|
Simplify the IRQ handling routine of ams driver.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Use a separate mutex to serialize input device creation/removal,
otheriwse we deadlock if we try to remove input device while it is
being polled. Also do not take ams_info.lock when it is not needed.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
We should not allow writes to the 'joystick' module parameters since
writing there will not trigger creation of the input device. Disable
writes since we provide alternative way of enabling input device via
AMS device's sysfs attribute.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
The legacy i2c binding model is phasing out, so the ams driver needs
to be converted to a new-style i2c driver. Here is a naive approach of
this conversion. Basically it is moving the i2c device creation from
the ams driver to the i2c-powermac driver. This should work, but I
suspect we could come up with something cleaner by declaring the i2c
device as part of the platform setup. This could be done later by
someone more familiar with openfirmware-based platforms than I am
myself.
One nice thing brought by this conversion is that the ams driver
should be loaded automatically on systems where is is needed (at
least when the I2C interface to the chip is used) providing
coldplug-aware user-space environment.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Stelian Pop <stelian@popies.net>
Cc: Michael Hanselmann <linux-kernel@hansmi.ch>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The lm87 driver normally assumes that firmware configured the chip
correctly. Since this is not always the case, alllow platform code to
set the channel register value via platform_data. All other
configuration registers can be changed after driver initialisation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
This means that if we have to start the monitor when probed, we also
stop it on removal.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
lm87_init_client() conditionally sets the Start bit and clears the
INT#_Clear bit in the Config 1 register. The condition should be that
either of these bits needs changing, but currently it checks the
(self-clearing) Initialization bit instead of INT#_Clear.
Fix the condition and also ensure we never set the Initialization bit.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Degrade the "Unsupported chip" message from info to debug level.
There's nothing wrong with this, so no need to bother the user.
Also make the message slightly more descriptive.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>
|
|
These Maxim chips are similar to MAX6657 but use unsigned temperature
values to allow for readings up to 145 degrees.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
The encoding of temperatures varies between chips and modes. So do not
use "temp1" or "temp2" in the names of the conversion functions, but
specify the encoding.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Martyn Welch <martyn.welch@gefanuc.com>
|
|
Support ADT7461 in extended temperature range mode, which will change
the range of readings from 0..127 to -64..191 degC. Adjust the
register conversion functions accordingly.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Martyn Welch <martyn.welch@gefanuc.com>
|
|
Use static functions instead of the TEMPx_FROM_REG* and TEMPx_TO_REG*
macros. This will ensure type safety and eliminate any side effects
from arguments passed in since the macros referenced 'val' multiple
times. This change should not affect functionality.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Martyn Welch <martyn.welch@gefanuc.com>
|
|
Update the links to the datasheet of some of the devices supported by
the lm90 driver. Also remove the links from the driver itself, so that
we don't have to update them twice each time they change.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>
|
|
The Maxim chips supported by the lm90 driver have 8-bit high and low
remote limit values, not 11-bit as the other chips have. So stop reading
from and writing to registers that do not exist on these chips. Also
round the limit values set by the user properly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>
|
|
The Maxim MAX6657, MAX6658 and MAX6659 have extra resolution bits for
the local temperature measurement. Let the lm90 driver read them and
export them to user-space.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>
|
|
Move the code which aggregates two 8-bit register values into a 16-bit
value to a separate function. We'll need to do it a second time soon and
I don't want to duplicate the code.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>
|
|
Now that device_create() has been audited, rename things back to the
original call to be sane.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (158 commits)
powerpc: Fix CHRP PCI config access for indirect_pci
powerpc/chrp: Fix detection of Python PCI host bridge on IBM CHRPs
powerpc: Fix 32-bit SMP boot on CHRP
powerpc: Fix link errors on 32-bit machines using legacy DMA
powerpc/pci: Improve detection of unassigned bridge resources
hvc_console: Fix free_irq in spinlocked section
powerpc: Get USE_STRICT_MM_TYPECHECKS working again
powerpc: Reflect the used arguments in machine_init() prototype
powerpc: Fix DMA offset for non-coherent DMA
powerpc: fix fsl_upm nand driver modular build
powerpc/83xx: add NAND support for the MPC8360E-RDK boards
powerpc: FPGA support for GE Fanuc SBC610
i2c: MPC8349E-mITX Power Management and GPIO expander driver
powerpc: reserve two DMA channels for audio in MPC8610 HPCD device tree
powerpc: document the "fsl,ssi-dma-channel" compatible property
powerpc: disable CHRP and PMAC support in various defconfigs
OF: add fsl,mcu-mpc8349emitx to the exception list
powerpc/83xx: add DS1374 RTC support for the MPC837xE-MDS boards
powerpc: remove support for bootmem-allocated memory for the DIU driver
powerpc: remove non-dependent load fsl_booke PTE_64BIT
...
|
|
Manual fixup of conflicts on:
arch/powerpc/include/asm/dcr-regs.h
drivers/net/ibm_newemac/core.h
|
|
The new-style dme1737 driver implements the optional detect() callback
to cover the use cases of the legacy driver. I don't actually expect
any new-style device for that driver, but as the old i2c API is going
away soon, we have to switch to the new one.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Juerg Haefliger <juergh@gmail.com>
|
|
The dme1737 driver support both LPC (ISA) and SMBus devices. At the
moment it's rather i2c-centric, and LPC variants use a fake i2c_client
for some operations.
In a near future, i2c_client will be allocated by i2c-core rather than
by the device drivers, so non-i2c drivers will not have one. As a
preparation step, change the driver code to no longer assume that
an i2c_client structure is always available. No functional change.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Juerg Haefliger <juergh@gmail.com>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:
sound/core/memalloc.c
|
|
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (236 commits)
[ARM] 5300/1: fixup spitz reset during boot
[ARM] 5295/1: make ZONE_DMA optional
[ARM] 5239/1: Palm Zire 72 power management support
[ARM] 5298/1: Drop desc_handle_irq()
[ARM] 5297/1: [KS8695] Fix two compile-time warnings
[ARM] 5296/1: [KS8695] Replace macro's with trailing underscores.
[ARM] pxa: allow multi-machine PCMCIA builds
[ARM] pxa: add preliminary CPUFREQ support for PXA3xx
[ARM] pxa: add missing ACCR bit definitions to pxa3xx-regs.h
[ARM] pxa: rename cpu-pxa.c to cpufreq-pxa2xx.c
[ARM] pxa/zylonite: add support for USB OHCI
[ARM] ohci-pxa27x: use ioremap() and offset for register access
[ARM] ohci-pxa27x: introduce pxa27x_clear_otgph()
[ARM] ohci-pxa27x: use platform_get_{irq,resource} for the resource
[ARM] ohci-pxa27x: move OHCI controller specific registers into the driver
[ARM] ohci-pxa27x: introduce flags to avoid direct access to OHCI registers
[ARM] pxa: move I2S register and bit definitions into pxa2xx-i2s.c
[ARM] pxa: simplify DMA register definitions
[ARM] pxa: make additional DCSR bits valid for PXA3xx
[ARM] pxa: move i2c register and bit definitions into i2c-pxa.c
...
Fixed up conflicts in
arch/arm/mach-versatile/core.c
sound/soc/pxa/pxa2xx-ac97.c
sound/soc/pxa/pxa2xx-i2s.c
manually.
|
|
Enable driver checking of the DMI product name (when enabled) on
an Abit AT8 32X, instead of falling back to a manual probe. This
eliminates false negatives and eventually will help avoid
unnecessary bus probes on unsupported mainboards.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Tested-by: Daniel Exner <dex@dragonslave.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
The table for the Abit AT8 32X was incorrectly missing an entry
for the sixth ("AUX3") fan. Add this entry, exporting the fan
reading to userspace.
Closes lm-sensors.org ticket #2339.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Tested-by: Daniel Exner <dex@dragonslave.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
On the Shuttle SN68PT, FAN_CTL2 is apparently not connected to a fan,
but to something else. One user has reported instant system power-off
when changing the PWM2 duty cycle, so we disable it.
I use the board name string as the trigger in case the same board is
ever used in other systems.
This closes lm-sensors ticket #2349:
pwmconfig causes a hard poweroff
http://www.lm-sensors.org/ticket/2349
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
This is not generic, and is added here for backward compatibility.
It is made an individual commit here to make it easier for revert
once the sharpsl_pm gets generic enough.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Driver based on corgi_ssp.c and sharpsl_pm.c, previously done by Richard
Purdie and many others.
Now changed to generic HWMON device and expose all the ADC input value
through sysfs.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch makes the needlessly global ad7414_update_device() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
The IT8712F v0.9.1 datasheet applies to revisions >= 0x8 (J).
The driver was incorrectly attempting to enable 16-bit fan
readings on rev 0x7 (I) which led to incorrect RPM values.
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Tested-by: John Gumb <john.gumb@tandberg.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
The atxp1 device detection code has a major logic flaw, fix it. Not
sure how we managed to miss this when the driver was merged...
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Sebastian Witt <se.witt@gmx.net>
|
|
As suggested by Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a PIC16F747 based controller that monitors and consolidates
the hardware access to various fan and temperature values reported by
adr7462 and similar devices behind an I2C bus.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Not all AMD K8 have 6 VID pins, contrary to what was assumed in
commit 116d0486bdefc11f71e567cadf0c47f788b4dd06. This commit broke
support of older CPU models which have only 5 VID pins:
http://bugzilla.kernel.org/show_bug.cgi?id=11329
We need two entries in the hwmon-vid table, one for 5-bit VID models
(K8 revision <= E) and one for 6-bit VID models (K8 revision >= F).
This fixes bug #11329.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Frank Myhr <fmyhr@fhmtech.com>
Tested-by: Jean-Luc Coulon <jean.luc.coulon@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add in the CPUID for Nehalem chips.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Kent Liu <kent.liu@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently, all sensors are read when the energy meter is queried via
sysfs. This introduces a considerable amount of delay and variation in
the sysfs reading, which is not desirable when trying to profile energy
use. Therefore, read only the energy meters when a sysfs query comes in
for them, and don't cache the results so that we always get the latest
reading.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
