| Age | Commit message (Collapse) | Author |
|---|
|
Make IDE_HWIFS configurable if EMBEDDED
This lets us lop as much as 16k off an x86 build. It's a little ugly, but
it's dead simple. Note the fix for HWIFS < 2.
Sizing interfaces dynamically unfortunately turns out to be pretty
major surgery.
add/remove: 0/1 grow/shrink: 0/11 up/down: 0/-16182 (-16182)
function old new delta
ide_hwifs 16920 1692 -15228
init_irq 1113 750 -363
ideprobe_init 283 138 -145
ide_pci_setup_ports 1329 1193 -136
save_match 85 - -85
ide_register_hw_with_fixup 367 287 -80
ide_setup 1364 1308 -56
is_chipset_set 40 4 -36
create_proc_ide_interfaces 225 205 -20
init_ide_data 84 67 -17
ide_probe_for_cmd640x 1198 1183 -15
ide_unregister 1452 1451 -1
Signed-off-by: Matt Mackall <mpm@selenic.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
In 2.6.15.1 I encountered some IDE crashes when unplugging IDE cables to
emulate disk errors. Below is a patch against 2.6.16 which I think still
applies.
1. The first BUG_ON could trigger when a PREFLUSH IO fails (it would
fail the original barrier request which hasn't been marked REQ_STARTED
yet).
2. the rq could have been dequeued already (same as 1).
3. HWGROUP(drive)->rq could be NULL because of the ide_error() several
lines earlier.
Signed-off-by: Hua Zhong <hzhong@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Release the DMA engine for the custom mapping IDE drivers also (for
example, siimage.c does allocate it in both I/O-mapped and custom-mapped
modes). Remove useless code from the error path of
ide_allocate_dma_engine().
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
- Claim extra DMA I/O ports regardless of what IDE channels are
present/enabled.
- Remove extra ports handling from ide_mapped_mmio_dma() since it's not
applicable to the custom-mapping IDE drivers.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Less functional than libata this just uses the merged interface provided for
dumb legacy OS's. This is basically a bridge for people not yet ready to use
libata for some reason or another.
Port visibility is entirely dependant on the BIOS setup.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
All on stack DECLARE_COMPLETIONs should be replaced by:
DECLARE_COMPLETION_ONSTACK
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Mirrors the drivers/ata version, hold a reference to the host bridge while we
are doing setup.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
As we don't support hotplug we end up leaking an isa_dev reference which if
unload was ever added we would drop at the end of unloading. This is fine
because we do genuinely need the isa_dev pointer until unload.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Simple conversion
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Make it possible to disable the block layer. Not all embedded devices require
it, some can make do with just JFFS2, NFS, ramfs, etc - none of which require
the block layer to be present.
This patch does the following:
(*) Introduces CONFIG_BLOCK to disable the block layer, buffering and blockdev
support.
(*) Adds dependencies on CONFIG_BLOCK to any configuration item that controls
an item that uses the block layer. This includes:
(*) Block I/O tracing.
(*) Disk partition code.
(*) All filesystems that are block based, eg: Ext3, ReiserFS, ISOFS.
(*) The SCSI layer. As far as I can tell, even SCSI chardevs use the
block layer to do scheduling. Some drivers that use SCSI facilities -
such as USB storage - end up disabled indirectly from this.
(*) Various block-based device drivers, such as IDE and the old CDROM
drivers.
(*) MTD blockdev handling and FTL.
(*) JFFS - which uses set_bdev_super(), something it could avoid doing by
taking a leaf out of JFFS2's book.
(*) Makes most of the contents of linux/blkdev.h, linux/buffer_head.h and
linux/elevator.h contingent on CONFIG_BLOCK being set. sector_div() is,
however, still used in places, and so is still available.
(*) Also made contingent are the contents of linux/mpage.h, linux/genhd.h and
parts of linux/fs.h.
(*) Makes a number of files in fs/ contingent on CONFIG_BLOCK.
(*) Makes mm/bounce.c (bounce buffering) contingent on CONFIG_BLOCK.
(*) set_page_dirty() doesn't call __set_page_dirty_buffers() if CONFIG_BLOCK
is not enabled.
(*) fs/no-block.c is created to hold out-of-line stubs and things that are
required when CONFIG_BLOCK is not set:
(*) Default blockdev file operations (to give error ENODEV on opening).
(*) Makes some /proc changes:
(*) /proc/devices does not list any blockdevs.
(*) /proc/diskstats and /proc/partitions are contingent on CONFIG_BLOCK.
(*) Makes some compat ioctl handling contingent on CONFIG_BLOCK.
(*) If CONFIG_BLOCK is not defined, makes sys_quotactl() return -ENODEV if
given command other than Q_SYNC or if a special device is specified.
(*) In init/do_mounts.c, no reference is made to the blockdev routines if
CONFIG_BLOCK is not defined. This does not prohibit NFS roots or JFFS2.
(*) The bdflush, ioprio_set and ioprio_get syscalls can now be absent (return
error ENOSYS by way of cond_syscall if so).
(*) The seclvl_bd_claim() and seclvl_bd_release() security calls do nothing if
CONFIG_BLOCK is not set, since they can't then happen.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
After Christophs SCSI change, the only usage left is RQ_ACTIVE
and RQ_INACTIVE. The block layer sets RQ_INACTIVE right before freeing
the request, so any check for RQ_INACTIVE in a driver is a bug and
indicates use-after-free.
So kill/clean the remaining users, straight forward.
Signed-off-by: Jens Axboe <axboe@suse.de>
|
|
As the comments indicates in blkdev.h, we can fold it into ->end_io_data
usage as that is really what ->waiting is. Fixup the users of
blk_end_sync_rq().
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Right now ->flags is a bit of a mess: some are request types, and
others are just modifiers. Clean this up by splitting it into
->cmd_type and ->cmd_flags. This allows introduction of generic
Linux block message types, useful for sending generic Linux commands
to block devices.
Signed-off-by: Jens Axboe <axboe@suse.de>
|
|
Support SB600 SATA legacy IDE (DMA enable).
Signed-off-by: Anatoli Antonovitch <antonovi@ati.com>
Cc: Jeff Garzik <jeff@garzik.org>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (47 commits)
Driver core: Don't call put methods while holding a spinlock
Driver core: Remove unneeded routines from driver core
Driver core: Fix potential deadlock in driver core
PCI: enable driver multi-threaded probe
Driver Core: add ability for drivers to do a threaded probe
sysfs: add proper sysfs_init() prototype
drivers/base: check errors
drivers/base: Platform notify needs to occur before drivers attach to the device
v4l-dev2: handle __must_check
add CONFIG_ENABLE_MUST_CHECK
add __must_check to device management code
Driver core: fixed add_bind_files() definition
Driver core: fix comments in drivers/base/power/resume.c
sysfs_remove_bin_file: no return value, dump_stack on error
kobject: must_check fixes
Driver core: add ability for devices to create and remove bin files
Class: add support for class interfaces for devices
Driver core: create devices/virtual/ tree
Driver core: add device_rename function
Driver core: add ability for classes to handle devices properly
...
|
|
The third argument of au1xxx_dbdma_chan_alloc's callback function is not
used anywhere.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Convert some framework code to handle the new PRETHAW message.
- IDE just treats it like a FREEZE.
- The pci_choose_state() thingie still doesn't use PCI_D0 when it gets a
FREEZE (and now PRETHAW) event, which seems rather buglike but wasn't
something to change with this patch.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Small driver suspend() fixes in preparation for the PRETHAW events:
- Only compare message events for equality against PM_EVENT_* codes;
not against integers, or using greater/less-than comparisons.
(PM_EVENT_* should really become a __bitwise thing.)
- Explicitly test for SUSPEND events (rather than not-something-else)
before suspending devices.
- Removes more of the confusion between a pm_message_t (wraps event code)
and a "state" ... suspend() originally took a target system state.
These updates are correct and appropriate even without new PM_EVENT codes.
benh: "I think in the Mesh case, we should handle the freeze case as well or
we might get wild DMA."
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Greg KH <greg@kroah.com>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Looks like a workaround for old bogus OF bitrot... This fixes it and
hence fixes boot on some performa machines.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
|
|
Configuration bits are not set properly for DMA on some chipset revisions.
It has already been corrected for M5229 (rev c7) but not for M5229 (rev
c8). This leads to the bug described at
http://bugzilla.kernel.org/show_bug.cgi?id=5786 (lost interrupt + ide bus
hangs).
Signed-off-by: Michael De Backer <micdb@skynet.be>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
VIA boards
There are two changes here. The first reverses the broken PCI_DEVICE
conversion back to the old format. The second adds a missing PCI ID so
you can actually boot 2.6.18 on 2 month old VIA motherboards (right now
only 2.6.18-mm works).
CC'd to Jeff to check the PCI ident but its a) in several distro kernels
and b) in 2.6.18-mm [twice ??]
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
New SiS south bridge device ID is 0x966.
Next coming product will be 0x968. (Will be released in Q4, this year)
We don't make any updates to the IDE controller.
Signed-off-by: David Wang <touch@sis.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Sergey Vlasov reported that his "FUJITSU MCC3064AP, ATAPI OPTICAL drive"
pops up as UNKNOWN in /proc/ide/*/media .
Closes #4145.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Fix some bugs in the patch that converted the IOC4 driver from port IO ops to
memio ops.
http://marc.theaimsgroup.com/?l=linux-ide&m=114895892231438&w=2
Problems fixed are:
- Call to default_hwif_mmiops() was not being done until _after_
first IO operation, resulting in the first IO operation being
done as a port IO op, instead of memio.
- request_region() calls needed to be request_mem_region()
- Incomplete error case handling.
- Non-usage of ioremap() and __iomem.
Signed-off-by: John Keller <jpk@sgi.com>
Signed-off-by: Jeremy Higdon <jeremy@sgi.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
The following change from -mm is important to 2.6.18 (actually to 2.6.17
but its too late for that). This was contributed over three months ago
by VIA to Bartlomiej and nothing happened. As a result the new chipset
is now out and Linux won't run on it. By the time 2.6.18 is finalised
this will be the defacto standard VIA chipset so support would be a good
plan.
Tested in -mm for a while, its essentially a PCI ident update but for
the bridge chip because VIA do things in weird ways.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
When the IDE fix for Jmicron went in one piece went walking somewhere
(send log shows my end somehow). Without this sometimes you get an oops
on boot.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Minor comment fix for misc_64.S
[POWERPC] Use H_CEDE on non-SMT
[POWERPC] force 64bit mode in fwnmi handlers to workaround firmware bugs
[POWERPC] PMAC_APM_EMU should depend on ADB_PMU
[POWERPC] Fix new interrupt code (MPIC detection)
[POWERPC] Fix new interrupt code (MPIC endianness)
[POWERPC] Add cpufreq support for Xserve G5
[POWERPC] Xserve G5 thermal control fixes
[POWERPC] Fix mem= handling when the memory limit is > RMO size
[POWERPC] More offb/bootx fixes
[POWERPC] Fix legacy_serial.c error handling on 32 bits
[POWERPC] Fix default clock for udbg_16550
[POWERPC] Fix non-MPIC CHRPs with CONFIG_SMP set
[POWERPC] Fix 32 bits warning in prom_init.c
[POWERPC] Workaround Pegasos incorrect ISA "ranges"
[POWERPC] fix up front-LED Kconfig
|
|
The SGI IOC4 IDE device always shares an interrupt with other devices which
are part of IOC4. As such, IDEPCI_SHARE_IRQ should always be enabled when
BLK_DEV_SGIIOC4 is enabled.
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
When resuming from suspend-to-RAM, the NMI watchdog detects a lockup in
ide_wait_not_busy. Here's a screenshot of the trace taken by a digital
camera: http://www.uamt.feec.vutbr.cz/rizeni/pom/DSC03510-2.JPG
Let's touch the NMI watchdog in ide_wait_not_busy. The system then resumes
correctly from STR.
[akpm@osdl.org: modular build fix]
Signed-off-by: Michal Schmidt <xschmi00@stud.feec.vutbr.cz>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Now that get_property() returns a void *, there's no need to cast its
return value. Also, treat the return value as const, so we can
constify get_property later.
powermac platform & macintosh driver changes.
Built for pmac32_defconfig, g5_defconfig
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Only enable dma for a valid speed setting.
Signed-off-by: Jens Axboe <axboe@suse.de>
|
|
It's the safer choice. Originally due to a bug in itx821x, but a
generally sound thing to do.
Signed-off-by: Jens Axboe <axboe@suse.de>
|
|
Some drives claim they support cache flushing, but get seriously
confused if you try. Add this option to be able to boot with
barriers enabled by default.
Signed-off-by: Jens Axboe <axboe@suse.de>
|
|
This patch fixes the front-LED Kconfig issues I introduced while
creating it. Apparently having a dependency isn't enough to have the
select not evaluated or something like that.
The patch also changes the default configuration for pmac32 select the
default for the LED to be the IDE trigger. While I was at it, I
completely updated the defconfig and also added snd-aoa to it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
if IO space is not available"
This reverts commit 5040cb8b7e61b7a03e8837920b9eb2c839bb1947.
It breaks previously working ide-cs PIO configurations, causing problems
like
ide2: I/O resource 0xF883200E-0xF883200E not free.
ide2: ports already in use, skipping probe
rather than a working kernel.
Cc: Thomas Kleffel <tk@maintech.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Prior to 2.6.18rc1 you could install with devices on a JMicron chipset
using the "all-generic-ide" option. As of this kernel the AHCI driver
grabs the controller and rams it into AHCI mode losing the PATA ports
and making CD drives and the like vanish. The all-generic-ide option
fails because the AHCI driver grabbed the PCI device and reconfigured
it.
To fix this three things are needed.
#1 We must put the chip into dual function mode
#2 The AHCI driver must grab only function 0 (already in your rc1 tree)
#3 Something must grab the PATA ports
The attached patch is the minimal risk edition of this. It puts the chip
into dual function mode so that AHCI will grab the SATA ports without
losing the PATA ports. To keep the risk as low as possible the third
patch adds the PCI identifiers for the PATA port and the FN check to the
ide-generic driver. There is a more featured jmicron driver on its way
but that adds risk and the ide-generic support is sufficient to install
and run a system.
The actual chip setup done by the quirk is the precise setup recommended
by the vendor.
(The JMB368 appears only in the ide-generic entry as it has no AHCI so
does not need the quirk)
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Rather long patch, apparently no one has updated the pmac32_defconfig in
a while.
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
lockdep needs to have the waitqueue lock initialized for on-stack waitqueues
implicitly initialized by DECLARE_COMPLETION(). Annotate on-stack completions
accordingly.
Has no effect on non-lockdep kernels.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Make use of local_irq_enable_in_hardirq() API to annotate places that enable
hardirqs in hardirq context.
Has no effect on non-lockdep kernels.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Missing variable initialisation would mean it would sometimes not put ATAPI
devices into DMA by default.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: <Jack.Lee@ite.com.tw>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial:
Remove obsolete #include <linux/config.h>
remove obsolete swsusp_encrypt
arch/arm26/Kconfig typos
Documentation/IPMI typos
Kconfig: Typos in net/sched/Kconfig
v9fs: do not include linux/version.h
Documentation/DocBook/mtdnand.tmpl: typo fixes
typo fixes: specfic -> specific
typo fixes in Documentation/networking/pktgen.txt
typo fixes: occuring -> occurring
typo fixes: infomation -> information
typo fixes: disadvantadge -> disadvantage
typo fixes: aquire -> acquire
typo fixes: mecanism -> mechanism
typo fixes: bandwith -> bandwidth
fix a typo in the RTC_CLASS help text
smb is no longer maintained
Manually merged trivial conflict in arch/um/kernel/vmlinux.lds.S
|
|
space is not available
This patch enables ide_cs to access CF-cards via their common memory
rather than via their IO space.
Signed-off-by: Thomas Kleffel <tk@maintech.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/devfs-2.6: (22 commits)
[PATCH] devfs: Remove it from the feature_removal.txt file
[PATCH] devfs: Last little devfs cleanups throughout the kernel tree.
[PATCH] devfs: Rename TTY_DRIVER_NO_DEVFS to TTY_DRIVER_DYNAMIC_DEV
[PATCH] devfs: Remove the tty_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the line_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the videodevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the gendisk devfs_name field as it's no longer needed
[PATCH] devfs: Remove the miscdevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the devfs_fs_kernel.h file from the tree
[PATCH] devfs: Remove devfs_remove() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_cdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_bdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_symlink() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_dir() function from the kernel tree
[PATCH] devfs: Remove devfs_*_tape() functions from the kernel tree
[PATCH] devfs: Remove devfs support from the sound subsystem
[PATCH] devfs: Remove devfs support from the ide subsystem.
[PATCH] devfs: Remove devfs support from the serial subsystem
[PATCH] devfs: Remove devfs from the init code
[PATCH] devfs: Remove devfs from the partition code
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (43 commits)
[POWERPC] Use little-endian bit from firmware ibm,pa-features property
[POWERPC] Make sure smp_processor_id works very early in boot
[POWERPC] U4 DART improvements
[POWERPC] todc: add support for Time-Of-Day-Clock
[POWERPC] Make lparcfg.c work when both iseries and pseries are selected
[POWERPC] Fix idr locking in init_new_context
[POWERPC] mpc7448hpc2 (taiga) board config file
[POWERPC] Add tsi108 pci and platform device data register function
[POWERPC] Add general support for mpc7448hpc2 (Taiga) platform
[POWERPC] Correct the MAX_CONTEXT definition
powerpc: minor cleanups for mpc86xx
[POWERPC] Make sure we select CONFIG_NEW_LEDS if ADB_PMU_LED is set
[POWERPC] Simplify the code defining the 64-bit CPU features
[POWERPC] powerpc: kconfig warning fix
[POWERPC] Consolidate some of kernel/misc*.S
[POWERPC] Remove unused function call_with_mmu_off
[POWERPC] update asm-powerpc/time.h
[POWERPC] Clean up it_lp_queue.h
[POWERPC] Skip the "copy down" of the kernel if it is already at zero.
[POWERPC] Add the use of the firmware soft-reset-nmi to kdump.
...
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
[PATCH] i386: export memory more than 4G through /proc/iomem
[PATCH] 64bit Resource: finally enable 64bit resource sizes
[PATCH] 64bit Resource: convert a few remaining drivers to use resource_size_t where needed
[PATCH] 64bit resource: change pnp core to use resource_size_t
[PATCH] 64bit resource: change pci core and arch code to use resource_size_t
[PATCH] 64bit resource: change resource core to use resource_size_t
[PATCH] 64bit resource: introduce resource_size_t for the start and end of struct resource
[PATCH] 64bit resource: fix up printks for resources in misc drivers
[PATCH] 64bit resource: fix up printks for resources in arch and core code
[PATCH] 64bit resource: fix up printks for resources in pcmcia drivers
[PATCH] 64bit resource: fix up printks for resources in video drivers
[PATCH] 64bit resource: fix up printks for resources in ide drivers
[PATCH] 64bit resource: fix up printks for resources in mtd drivers
[PATCH] 64bit resource: fix up printks for resources in pci core and hotplug drivers
[PATCH] 64bit resource: fix up printks for resources in networks drivers
[PATCH] 64bit resource: fix up printks for resources in sound drivers
[PATCH] 64bit resource: C99 changes for struct resource declarations
Fixed up trivial conflict in drivers/ide/pci/cmd64x.c (the printk that
was changed by the 64-bit resources had been deleted in the meantime ;)
|
