aboutsummaryrefslogtreecommitdiff
path: root/drivers/ieee1394/sbp2.c
AgeCommit message (Collapse)Author
2007-02-08ieee1394: sbp2: lower block queue alignment requirementStefan Richter
The old setting is copy & waste from usb-storage and doesn't apply to sbp2. There is only 4-byte alignment required for everything, except for S/G table elements which have to be 8-byte aligned according to the SBP-2 spec. (They happen to be ____cacheline_aligned in our implementation. Whether that's good is another question.) We now simply don't tune block queue alignment at all. The default alignment would surely never become anything else than a multiple of 4, else tons of calls to blk_queue_dma_alignment would have to be added everywhere in drivers/... Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2007-02-08ieee1394: sbp2: remove bogus "emulated" host flagStefan Richter
There is no emulation going on here. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2007-02-08ieee1394: sbp2: use a better wildcard for blacklistStefan Richter
0x000000 could be a valid value to match against, but anything bigger than 0xffffff cannot. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2007-01-10ieee1394: sbp2: fix probing of some DVD-ROM/RWsStefan Richter
Since commit 98e238cd42be6c0852da519303cf0182690f8d9f in Linux 2.6.19, "ieee1394: sbp2: don't prefer MODE SENSE 10", some FireWire DVD-ROMs and DVD-RWs were mistaken as CD-ROM because sr_mod now sent MODE SENSE 6. The MMC command set includes only MODE SENSE 10. http://bugzilla.kernel.org/show_bug.cgi?id=7800 This fix lets sbp2 switch scsi_device.use_10_for_rw on for MMC LUs. This should rather be done in the command set driver sr_mod, not in the sbp2 transport driver, and an according patch will follow for a next Linux release. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2006-12-30ieee1394: sbp2: fix bogus dma mappingStefan Richter
Need to use a PCI device, not a FireWire host device. Problem found by Andreas Schwab, mistake pointed out by Benjamin Herrenschmidt. http://ozlabs.org/pipermail/linuxppc-dev/2006-December/029595.html Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Tested-by: Andreas Schwab <schwab@suse.de>
2006-12-30ieee1394: sbp2: pass REQUEST_SENSE through to the targetStefan Richter
Delete some incorrect code, left over from the initial driver submission in March 2001. SBP-2 targets should provide sense data via the SBP-2 status block (autosense). We have to pass the REQUEST_SENSE command through to targets which don't implement autosense, if there are any, and to accomodate application clients which use this command. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2006-12-07ieee1394: sbp2: code formatting around work_struct stuffStefan Richter
Merge is finished, can bring the code in readable style again. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2006-12-07ieee1394: Consolidate driver registeringBen Collins
This patch consolidates some bookkeeping for driver registering. It closely models what pci_register_driver() does. The main addition is that the owner of the driver is set, so we get a proper symlink for /sys/bus/ieee1394/driver/*/module. Also moves setting of name and bus type into nodemgr. Because of this, we can remove the EXPORT_SYMBOL for ieee1394_bus_type, since it's now only used in ieee1394.ko. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2006-12-07ieee1394: sbp2: convert from PCI DMA to generic DMAStefan Richter
API conversion without change in functionality Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2006-12-07ieee1394: sbp2: wrap two functions into oneStefan Richter
Move the body of a function into its only caller. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2006-12-07ieee1394: sbp2: update comment on things to doStefan Richter
Some people actually look at those comments. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2006-12-07ieee1394: sbp2: use list_move_tail()Stefan Richter
It's OK to reorder list_del() and sbp2util_free_command_dma() here. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2006-12-07ieee1394: sbp2: more concise names for types and variablesStefan Richter
"struct scsi_id_instance_data" represents a logical unit. Rename it to "struct sbp2_lu", and "scsi_id" to "lu". Rename some other variables too. Wrap almost all lines after at most 80 columns. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2006-12-07ieee1394: sbp2: remove unused struct membersStefan Richter
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2006-12-07ieee1394: sbp2: proper unit in module parameter descriptionStefan Richter
It's 2^20 bit/s, not 0.001 bit. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2006-12-07ieee1394: sbp2: clean up sbp2_ namespaceStefan Richter
Prepend sbp2*_ to anything globally defined in sbp2.c except for some macros. Strip sbp2_ from names of struct members. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2006-12-07ieee1394: sbp2: some conditions in queue_command are unlikelyStefan Richter
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2006-12-07ieee1394: sbp2: remove superfluous commentsStefan Richter
And update and reformat remaining comments. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2006-12-07ieee1394: sbp2: delayed_work -> work_structStefan Richter
This work is not delayed. Also bring the code format in a state which reduces my work to merge pending sbp2 patchs. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2006-12-07ieee1394: sbp2: remove debug macrosStefan Richter
No need to keep them in released sources. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2006-12-07ieee1394: sbp2: consolidate log levelsStefan Richter
Replace some calls to SBP2_ERR and SBP2_WARN by SBP2_INFO. Remove logging macros SBP2_NOTICE and SBP2_WARN. Remove direct usage of HPSB_ logging macros. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2006-12-07ieee1394: sbp2: remove duplicate codeStefan Richter
The same case is handled further below in sbp2scsi_complete_command. Note, the second version behaves slightly different but looks preferable. It's an extremely unlikely case by the way. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2006-12-07ieee1394: sbp2: remove dead codeStefan Richter
This has been within #if 0 for a long time and is wrong anyway. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2006-12-07ieee1394: sbp2: clean up function declarationsStefan Richter
Remove unnecessary function prototypes. Remove variable names from function prototypes. Move declarations from sbp2.h to sbp2.c. Move definitions of driver templates together near the top of sbp2.c. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2006-12-07ieee1394: sbp2: remove irritating log messageStefan Richter
The queue depth can be read from /sys/bus/scsi/devices/*/queue_depth, so don't log it. And the hint about speed improvements is misleading, at least under current kernels. If serialization is switched off, read performance is typically increased by less than 10%. (I did not test write performance recently.) On the other hand, serialize_io=0 is not yet safe due to some implementation issues that are not trivial to fix. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2006-12-07ieee1394: sbp2: slightly reorder sbp2scsi_abortStefan Richter
Put the target's fetch agent into reset state before the underlying ORB DMA is unmapped and the ->done handler is called. It is highly unlikely but the target could access that ORB right before sbp2 sends the reset request. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2006-11-22WorkStruct: make allyesconfigDavid Howells
Fix up for make allyesconfig. Signed-Off-By: David Howells <dhowells@redhat.com>
2006-09-17ieee1394: sbp2: enable auto spin-up for all SBP-2 devicesStefan Richter
This is a follow-up to patch "ieee1394: sbp2: enable auto spin-up for Maxtor disks". When I 'ejected' an OXUF922 based HDD from a Mac OS X box, it was spun down by the Mac and did not spin up by itself when attached to a Linux box right after that. The first SCSI command that required the bridge to access the drive ended in sda:<6>sd 18:0:0:0: Device not ready: <6>: Current: sense key: Not Ready Additional sense: Logical unit not ready, initializing cmd. required Therefore the flag which instructs scsi_mod to send START STOP UNIT with START=1 ("make medium ready") after such a condition is now enabled unconditionally for all FireWire storage devices. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2006-09-17ieee1394: sbp2: don't prefer MODE SENSE 10Stefan Richter
In the old days, sbp2 used to coerce all MODE SENSE commands into the 10 bytes version. When all command set conversions were removed from sbp2 several months ago, sdev->use_10_for_ms = 1 was added. Meaning, higher SCSI layers preferred the 10 bytes version but would try the 6 bytes version if the former failed. Recently, a problem with the 10 bytes version was discovered. An Initio INIC-1530 firmware accepted the 10 bytes version but replied with bogus data, showing the HDD incorrectly as write-protected. Since RBC actually mandates MODE SENSE (6), I checked which version was sent by Windows XP and Mac OS X 10.3 to an SBP-2 target hosted by Linux --- it was the 6 bytes version. (Exception: OS X sent the 10 bytes version to an MMC target. RBC and SBC got MODE SENSE (6).) Therefore, drop the use_10_for_ms flag from sbp2. Now the upper layers will try MODE SENSE (6) before MODE SENSE (10) on all SBP-2 devices. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2006-09-17ieee1394: sbp2: prevent rare deadlock in shutdownStefan Richter
Scsi_remove_device() may go into uninterruptible sleep if blocked. Therefore sbp2_remove() unblocks the Scsi_Host before the device is requested to be removed. But there could be another 1394 bus reset after that which would block the host again. The 1394 subsystem won't call sbp2_update() concurrently to sbp2_remove(), which is why there is no chance for sbp2_remove() to be unblocked by sbp2_update(). The fix is to tell sbp2's bus reset handler when a device is to be shut down so that it skips scsi_block_requests() on that host. As before, any new commands after a reset without reconnect will be failed quickly by sbp2scsi_queuecommand(). In the long term, means to go without scsi_block_requests() should be found. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2006-09-17ieee1394: sbp2: update includesStefan Richter
Remove unused includes. Add missing includes, i.e. explicitly include all used headers. Sort includes alphabetically. Replace one call to signal_pending(current) to avoid to include headers just for this line. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2006-09-17ieee1394: sbp2: better handling of transport errorsStefan Richter
If the target signals a transport failure via status block, complete the request with DID_BUSY to indicate to the SCSI subsystem that the command may succeed when retried. Also log diagnostic information if the status block shows a transport related problem. It may point to hardware faults. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2006-09-17ieee1394: sbp2: recheck node generation in sbp2_updateStefan Richter
While sbp2_update() is doing its duties after a bus reset, another reset could happen. Don't accept new requests until the next undisturbed sbp2_update() or until sbp2_remove(). Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2006-09-17ieee1394: sbp2: safer agent reset in error handlersStefan Richter
The scsi_host_template's eh_abort_handler and eh_device_reset_handler are allowed to sleep. Use this to run sbp2_agent_reset in the more reliable mode which returns _after_ its write transaction was finished. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2006-09-17ieee1394: sbp2: handle "sbp2util_node_write_no_wait failed"Stefan Richter
Fix for http://bugzilla.kernel.org/show_bug.cgi?id=6948 Because sbp2 writes to the target's fetch agent's registers from within atomic context, it cannot sleep to guaranteedly get a free transaction label. This may repeatedly lead to "sbp2util_node_write_no_wait failed" and consequently to SCSI command abortion after timeout. A likely cause is that many queue_command softirqs may occur before khpsbpkt (the ieee1394 driver's thread which cleans up after finished transactions) is woken up to recycle tlabels. Sbp2 now schedules a workqueue job whenever sbp2_link_orb_command fails in sbp2util_node_write_no_wait. The job will reliably get a transaction label because it can sleep. We use the kernel-wide shared workqueue because it is unlikely that the job itself actually needs to sleep. In the improbable case that it has to sleep, it doesn't need to sleep long since the standard transaction timeout is 100ms. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2006-09-17ieee1394: safer definition of empty macrosStefan Richter
A deactivated macro, defined as "#define foo(bar)", will result in silent corruption if somebody forgets a semicolon after a call to foo. Replace it by "#define foo(bar) do {} while (0)" which will reveal any respective syntax errors. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2006-09-17the scheduled removal of drivers/ieee1394/sbp2.c:force_inquiry_hackAdrian Bunk
This patch contains the scheduled removal of the force_inquiry_hack module parameter. Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2006-09-17ieee1394: sbp2: convert sbp2util_down_timeout to waitqueueStefan Richter
The waitqueue API is used to replace a custom wait mechanism. Only one global waitqueue (instead of per-device waitqueues or completions) is added because there is usually just one waiter. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2006-09-17ieee1394: sbp2: more checks of status blockStefan Richter
- Add checks for the (very unlikely) cases that the target writes too little or too much status data or writes unsolicited status. - Indicate that these and similar conditions are unlikely(). - Check the 'resp' and 'sbp_status' fields for possible failure status. - Slightly optimize access macros for the status block bitfields. - Unify a few related log messages. TODO: Check if 'src'==1, then withhold the respective ORB from reuse until status for any subsequent ORB was received. This is an old bug whose fix requires more complex command queue handling. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2006-09-17ieee1394: sbp2: safer initialization of status fifoStefan Richter
Sbp2's copy of the status fifo was cleared when management ORBs or new command ORBs were prepared. The latter had potential for a race condition if the block layer's soft IRQ and the 1394 LLD's interrupt handler ran on different CPUs. It would also yield wrong status if a command was completed with non-zero completion status before other commands that had zero completion status, and no new command was enqueued in the meantime. Now, the status buffer is cleared right before it is written. Thus it ends up in the following simpler and safer access pattern: - sbp2_alloc_device: allocates and implicitly clears once, - sbp2_handle_status_write: clears, writes, and reads, - sbp2_query_logins, sbp2_login_device, sbp2_reconnect_device: read. The latter three do not race with sbp2_handle_status_write because of how the protocol works. As a tiny optimization, the first two quadlets of the status never need to be cleared. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2006-09-17ieee1394: sbp2: optimize DMA direction of command ORBsStefan Richter
Only the driver writes ORBs, the device just reads them. Therefore PCI_DMA_BIDIRECTIONAL can be replaced by PCI_DMA_TODEVICE which may be cheaper on some architectures. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2006-09-17ieee1394: sbp2: discard return value of sbp2_link_orb_commandStefan Richter
Since sbp2 is at the moment unable to do anything with the return value of sbp2_link_orb_command, just discard it. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2006-09-17ieee1394: sbp2: safer last_orb and next_ORB handlingStefan Richter
The sbp2 initiator has two ways to tell a target's fetch agent about new command ORBs: - Write the ORB's address to the ORB_POINTER register. This must not be done while the fetch agent is active. - Put the ORB's address into the previously submitted ORB's next_ORB field and write to the DOORBELL register. This may be done while the fetch agent is active or suspended. It must not be done while the fetch agent is in reset state. Sbp2 has a last_orb pointer which indicates in what way a new command should be announced. That pointer is concurrently accessed at various occasions. Furthermore, initiator and target are accessing the next_ORB field of ORBs concurrently and asynchronously. This patch does: - Protect all initiator accesses to last_orb by sbp2_command_orb_lock. - Add pci_dma_sync_single_for_device before a previously submitted ORB's next_ORB field is overwritten. - Insert a memory barrier between when next_ORB_lo and next_ORB_hi are overwritten. Next_ORB_hi must not be updated before next_ORB_lo. - Remove the rather unspecific and now superfluous qualifier "volatile" from the next_ORB fields. - Add comments on how last_orb is connected with what is known about the target's fetch agent's state. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2006-07-03[PATCH] ieee1394: replace __inline__ by inlineStefan Richter
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
2006-07-03[PATCH] ieee1394: sbp2: enable auto spin-up for Maxtor disksStefan Richter
At least Maxtor OneTouch III require a "start stop unit" command after auto spin-down before the next access can proceed. This patch activates the responsible code in scsi_mod for all Maxtor SBP-2 disks. https://bugzilla.novell.com/show_bug.cgi?id=183011 Maybe that should be done for all SBP-2 disks, but better be cautious. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
2006-06-30Remove obsolete #include <linux/config.h>Jörn Engel
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de> Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-06-12ieee1394: add preprocessor constant for invalid csr addressBen Collins
Replace occurrences of the magic value ~(u64)0 for invalid CSR address spaces by a named constant for better readability. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
2006-06-12sbp2: fix deregistration of status fifo address spaceBen Collins
The proper designator of an invalid CSR address is ~(u64)0, not (u64)0. Use the correct value in initialization and deregistration. Also, scsi_id->sbp2_lun does not need to be initialized twice. (scsi_id was kzalloc'd.) Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
2006-06-12sbp2: fix S800 transfers if phys_dma is offBen Collins
If sbp2 is forced to move data via ARM handler, the maximum packet size allowed for S800 transfers exceeds ohci1394's buffer size on platforms where PAGE_SIZE is 4096. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
2006-06-12sbp2: remove ohci1394 specific constantBen Collins
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Ben Collins <bcollins@ubuntu.com>