Age | Commit message (Collapse) | Author |
|
Set IB_QP_CREATE_BLOCK_MULTICAST_LOOPBACK for IPoIB's UD QPs if
supported by the underlying device. This creates an improvement of up
to 39% in bandwidth when sending multicast packets with IPoIB, and an
improvment of 12% in cpu usage.
Signed-off-by: Ron Livne <ronli@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
For devices that don't support SRQs, ipoib_cm_post_receive_nonsrq() is
called from both ipoib_cm_handle_rx_wc() and ipoib_cm_nonsrq_init_rx(),
and these two callers are not synchronized against each other.
However, ipoib_cm_post_receive_nonsrq() always reuses the same receive
work request and scatter list structures, so multiple callers can end
up stepping on each other, which leads to posting garbled work
requests.
Fix this by having the caller pass in the ib_recv_wr and ib_sge
structures to use, and allocating new local structures in
ipoib_cm_nonsrq_init_rx().
Based on a patch by Pradeep Satyanarayana <pradeep@us.ibm.com> and
David Wilder <dwilder@us.ibm.com>, with debugging help from Hoang-Nam
Nguyen <hnguyen@de.ibm.com>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The connected mode implementation in the IPoIB driver has a large
overhead in the way SKBs are handled in the receive flow. It usually
allocates an SKB with as big as was used in the currently received SKB
and moves unused fragments from the old SKB to the new one. This
involves a loop on all the remaining fragments and incurs overhead on
the CPU. This patch, for small SKBs, allocates an SKB just large
enough to contain the received data and copies to it the data from the
received SKB. The newly allocated SKB is passed to the stack and the
old SKB is reposted.
When running netperf, UDP small messages, without this pach I get:
UDP UNIDIRECTIONAL SEND TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to
14.4.3.178 (14.4.3.178) port 0 AF_INET
Socket Message Elapsed Messages
Size Size Time Okay Errors Throughput
bytes bytes secs # # 10^6bits/sec
114688 128 10.00 5142034 0 526.31
114688 10.00 1130489 115.71
With this patch I get both send and receive at ~315 mbps.
The reason that send performance actually slows down is as follows:
When using this patch, the overhead of the CPU for handling RX packets
is dramatically reduced. As a result, we do not experience RNR NAK
messages from the receiver which cause the connection to be closed and
reopened again; when the patch is not used, the receiver cannot handle
the packets fast enough so there is less time to post new buffers and
hence the mentioned RNR NACKs. So what happens is that the
application *thinks* it posted a certain number of packets for
transmission but these packets are flushed and do not really get
transmitted. Since the connection gets opened and closed many times,
each time netperf gets the CPU time that otherwise would have been
given to IPoIB to actually transmit the packets. This can be verified
when looking at the port counters -- the output of ifconfig and the
oputput of netperf (this is for the case without the patch):
tx packets
==========
port counter: 1,543,996
ifconfig: 1,581,426
netperf: 5,142,034
rx packets
==========
netperf 1,1304,089
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
|
|
They don't get updated by git and so they're worse than useless.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The SRP initiator is currently using ib_find_cached_pkey() and
ib_get_cached_gid() in situations where the uncached ib_find_pkey()
and ib_query_gid() functions serve just as well: sleeping is allowed
and performance is not an issue. Since we want to eliminate the
cached operations in the long term, convert SRP to use the uncached
variants.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
We saw a kernel oops in our regression testing when a multicast "join
finish" occurred just after the interface was -- this is
<https://bugs.openfabrics.org/show_bug.cgi?id=1040>. The test
randomly causes the HCA physical port to go down then up.
The cause of this is that ipoib_mcast_join_finish() processing happen
just after ipoib_mcast_dev_flush() was invoked (in which case the
broadcast pointer is NULL). This patch tests for and handles the case
where priv->broadcast is NULL.
Cc: <stable@kernel.org>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Commit f56bcd80 ("IPoIB: Use separate CQ for UD send completions")
introduced a bug where the transmit queue could get stopped and never
woken up. The problem is that send completions are only polled at the
end of the xmit function, so if the send queue fills up and the xmit
path stops the queue, then there is no way for send completions to
ever get polled, and so the transmit queue stays stopped forever.
Fix this by arming the send CQ just before posting the last send
request that fills the send queue. Then, when the completion event
handler is called, drain the send CQ. Since it is possible that not
enough send completions are in the CQ, verify that the the net queue
has been woken up after draining the send CQ, and if not arm a timer
and drain again at the timer function.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
When creating a child interface, copy the MTU information from the
parent. Otherwise when the child's multicast join completes, the MTU
will not be updated since the code does
dev->mtu = min(priv->mcast_mtu, priv->admin_mtu);
and priv->admin_mtu will be set to 0.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Use a dedicated CQ for UD send completions. Also, do not arm the UD
send CQ, which reduces the number of interrupts generated. This patch
farther reduces overhead by not calling poll CQ for every posted send
WR -- it does polls only when there 16 or more outstanding work requests.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Count FMR alignment violations per session as part of the iscsi
statistics.
Signed-off-by: Eli Dorfman <elid@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Add another level for debug.
Signed-off-by: Eli Dorfman <elid@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
This patch enables IPoIB to use 4K UD messages (when the underlying
device and fabrics support a 4K MTU) by using two scatter buffers when
PAGE_SIZE is less than or equal to thhe HCA IB MTU size. The first
buffer is for IPoIB header + GRH header, and the second buffer is the
IPoIB payload, which is 4K-4.
Signed-off-by: Shirley Ma <xma@us.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
It's big, but there doesn't seem to be a way to split it up smaller...
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This sets us up to be able to convert the srp_host to use a struct
device instead of a class_device.
Based on a original patch from Tony Jones, but split up into this piece
by Greg.
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Reviewed-by: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The itt field in struct iscsi_data is not defined with any particular
endianness. open-iscsi should use it as-is without byte-swapping it.
This fixes sparse warnings coming from doing ntohl(hdr->itt).
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
If a P_Key is deleted and then re-added at the same index, then IPoIB
gets confused because __ipoib_ib_dev_flush() only checks whether the
index is the same without checking whether the P_Key was present, so
the interface is stopped when the P_Key is deleted, but the event when
the P_Key is re-added gets ignored and the interface never gets
restarted.
Also, switch to using ib_find_pkey() instead of ib_find_cached_pkey()
everywhere in IPoIB, since none of the places that look for P_Keys are
in a fast path or in non-sleeping context, and in general we want to
kill off the whole caching infrastructure eventually. This also fixes
consistency problems caused because some IPoIB queries were cached and
some were uncached during the window where the cache was not updated.
Thanks to Venkata Subramonyam <vsubramo@cisco.com> for debugging this
problem and testing this fix.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
When a RDMA_CM_EVENT_DEVICE_REMOVAL event is raised, iSER should
release the connection resources.
This is necessary when the IB HCA module is unloaded while open-iscsi
is still running. Currently, iSER just BUG()s.
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
This can be used to tune at run time the parameters controlling the
event (interrupt) generation rate and thus reduce the overhead
incurred by handling interrupts resulting in better throughput. Since
IPoIB uses a single CQ for both RX and TX, RX is chosen to dictate
configuration for both RX and TX.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Just add the infrastructure so we can add functionality later.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
For HCAs that support TCP segmentation offload (IB_DEVICE_UD_TSO), set
NETIF_F_TSO and use HW LSO to offload TCP segmentation.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Convert list_splice() + INIT_LIST_HEAD() to the equivalent list_splice_init()
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The current SRP initiator will allow unlimited s/g entries in the
indirect descriptors lists, but the entry count field in the SRP_CMD
request is 8 bits, so setting srp_sg_tablesize too large will open the
possibility of wrapping the count and generating invalid requests.
Clamp srp_sg_tablesize to the protocol limits to prevent surprises.
Reported by Martin W. Schlining III <mschlining@datadirectnet.com>.
Signed-off-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
For HCAs that support checksum offload (ie that set IB_DEVICE_UD_IP_CSUM
in the device capabilities flags), have IPoIB set NETIF_F_IP_CSUM and
use the HCA to generate and verify IP checksums.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Commit 7143740d ("IPoIB: Add send gather support") made struct
ipoib_tx_buf significantly larger, since the mapping member changed
from a single u64 to an array with MAX_SKB_FRAGS + 1 entries. This
means that allocating tx_rings with kzalloc() may fail because there
is not enough contiguous memory for the new, much bigger size. Fix
this regression by allocating the rings with vmalloc() instead.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Commit 7143740d ("IPoIB: Add send gather support") made it possible
for tx_wr.num_sge to be != 1 -- this happens if send gather support is
enabled. However, the code in the connected mode post_send() function
assumes the old invariant, namely that tx_wr.num_sge is always 1. Fix
this by explicitly setting tx_wr.num_sge to 1 in the CM post_send().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
When set_multicast_list() is called the multicast task is restarted
and the IPOIB_MCAST_STARTED bit is cleared. As a result for some
window of time, multicast packets are not transmitted nor queued but
rather dropped by ipoib_mcast_send(). These dropped packets are
painful in two cases:
- bonding fail-over which both calls set_multicast_list() on the new
active slave and sends Gratuitous ARP through that slave.
- IP_DROP_MEMBERSHIP code which both calls set_multicast_list() on the
device and issues IGMP leave.
In both these cases, depending on the scheduling of the IPoIB
multicast task, the packets would be dropped. As a result, in the
bonding case, the failover would not be detected by the peers until
their neighbour is renewed the neighbour (which takes a few tens of
seconds). In the IGMP case, the IP router doesn't get an IGMP leave
and would only learn on that from further probes on the group (also a
delay of at least a few tens of seconds).
Fix this by allowing transmission (or queuing) depending on the
IPOIB_FLAG_OPER_UP flag instead of the IPOIB_MCAST_STARTED flag.
Signed-off-by: Olga Shern <olgas@voltaire.com>
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
"iser_device" allocation failure is "handled" with a BUG_ON() right
before dereferencing the NULL-pointer - fix this!
Signed-off-by: Arne Redlich <arne.redlich@xiranet.com>
Signed-off-by: Erez Zilber <erezz@voltaire.com>
|
|
The iteration through the list of "iser_device"s during device
lookup/creation is broken -- it might result in an infinite loop if
more than one HCA is used with iSER. Fix this by using
list_for_each_entry() instead of the open-coded flawed list iteration
code.
Signed-off-by: Arne Redlich <arne.redlich@xiranet.com>
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Commit efcd9971 ("IPoIB/cm: Factor out ipoib_cm_free_rx_reap_list()")
introduced a bug in ipoib_cm_dev_stop() when the receive drain times
out. In that case, the function moves all the pending rx stuff into a
private list but then calls ipoib_cm_free_rx_reap_list(), which
handles a different list.
Fix this by moving everything to the rx_reap_list that will actually
get freed up.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=906>.
Signed-off-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
struct ipoib_cm_tx.ibwc is unused since commit 1b524963 ("IPoIB/cm:
Use common CQ for CM send completions"), so remove it.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
|
|
In P_Key event handling, if the old P_Key is no longer available, the
driver must call ipoib_ib_dev_stop() -- just as it does when the P_Key
is still available (see procedure __ipoib_ib_dev_flush()).
When a P_Key becomes available, the driver will perform ipoib_open(),
which assumes that the QP is in RESET, the cm_id has been
destroyed/deleted, etc. If ipoib_ib_dev_stop() is not called as
described above, then these assumptions will be false, and the attempt
to bring the interface up will fail.
Found by Mellanox QA.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
This patch acts as a preparation for using checksum offload for IB
devices capable of inserting/verifying checksum in IP packets. The
patch does not actaully turn on NETIF_F_SG - we defer that to the
patches adding checksum offload capabilities.
We only add support for send gathers for datagram mode, since existing
HW does not support checksum offload on connected QPs.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
All current InfiniBand devices can handle all DMA addresses, and it's
hard to imagine anyone would be silly enough to build a new device
that couldn't. Therefore, enable the NETIF_F_HIGHDMA feature for IPoIB.
This has no effect for no, but is needed when we enable gather/scatter
support and checksum stateless offloads.
Signed-off-by: Eli Cohen <eli@mellnaox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
When a host just goes away (crash, power loss, etc.) without tearing
down its IB connections, it can get stale connection errors when it
tries to reconnect to targets upon rebooting. Retrying the connection
a few times will prevent sysadmins from playing the "which disk(s)
went missing?" game.
This would have made things slightly quicker when tracking down some
of the recent bugs, but it also helps quite a bit when you've got a
large number of targets hanging off a wedged server.
Signed-off-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Commit 732a2170 ("IB/ipoib: Bound the net device to the ipoib_neigh
structue") left a misleading debug print (n->dev would be a bond
device only if boding is used). Clean it up.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Move up the code that checks for a situation where the remote GID
stored in the ipoib_neigh is different than the one present in the
neighbour (handle gratuitous ARP) or that a bonding fail over has
happened but the neighbour still has a pointer to an ipoib_neigh
created by a different device than the current slave. This will cause
the driver to apply the check also for connected mode neighbours.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
With the sg table code, every SCSI driver is now either chain capable
or broken (or has sg_tablesize set so chaining is never activated), so
there's no need to have a check in the host template.
Also tidy up the code by moving the scatterlist size defines into the
SCSI includes and permit the last entry of the scatterlist pools not
to be a power of two.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (200 commits)
[SCSI] usbstorage: use last_sector_bug flag universally
[SCSI] libsas: abstract STP task status into a function
[SCSI] ultrastor: clean up inline asm warnings
[SCSI] aic7xxx: fix firmware build
[SCSI] aacraid: fib context lock for management ioctls
[SCSI] ch: remove forward declarations
[SCSI] ch: fix device minor number management bug
[SCSI] ch: handle class_device_create failure properly
[SCSI] NCR5380: fix section mismatch
[SCSI] sg: fix /proc/scsi/sg/devices when no SCSI devices
[SCSI] IB/iSER: add logical unit reset support
[SCSI] don't use __GFP_DMA for sense buffers if not required
[SCSI] use dynamically allocated sense buffer
[SCSI] scsi.h: add macro for enclosure bit of inquiry data
[SCSI] sd: add fix for devices with last sector access problems
[SCSI] fix pcmcia compile problem
[SCSI] aacraid: add Voodoo Lite class of cards.
[SCSI] aacraid: add new driver features flags
[SCSI] qla2xxx: Update version number to 8.02.00-k7.
[SCSI] qla2xxx: Issue correct MBC_INITIALIZE_FIRMWARE command.
...
|
|
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
qdisc_run() now tests for queue_stopped() before calling
__qdisc_run(), and the same check is done in every iteration of
__qdisc_run(), so another check is not required in the driver xmit.
This means that ipoib_start_xmit() no longer needs to test
netif_queue_stopped(); the test was added to fix earlier kernels,
where the networking stack did not guarantee that the xmit method of
an LLTX driver would not be called after the queue was stopped, but
current kernels do provide this guarantee.
To validate, I put a debug in the TX_BUSY path which never hit with 64
threads running overnight exercising this code a few 100 million
times.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Add a .change_queue_depth handler to the scsi_host_template in the
iSER driver. iscsi_change_queue_depth was added to iscsi_tcp in order
to solve the problem of queue depth which was too high for some
targets. It is also applicable for iSER.
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Some RDMA CM events are not supported or not handled in iSER.
This patch adds some info (printk) for the user about them.
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
When you have multiple targets, it gets really confusing when you try
to track down who did a reset when there is no identifying information
in the log message, especially when the same extension ID is mapped
through two different local IB ports. So, add an identifier that can
be used to track back to which local IB port/remote target pair is the
one having problems.
Signed-off-by: David Dillow <dillowda@ornl.gov>
Acked-by: Pete Wyckoff <pw@osc.edu>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Some HCAs (such as ehca2) support SRQ, but only support fewer than 16 SG
entries for SRQs. Currently IPoIB/CM implicitly assumes all HCAs will
support 16 SG entries for SRQs (to handle a 64K MTU with 4K pages). This
patch removes that restriction by limiting the maximum MTU in connected
mode to what the maximum number of SRQ SG entries allows.
This patch addresses <https://bugs.openfabrics.org/show_bug.cgi?id=728>
Signed-off-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
By default, the SCSI mid-layer seems to send down 512KB requests
(sg_tablesize = 256), with some requests occasionally combined. By
allowing the mid-layer to chain requests, we can easily grow to 1024KB
or larger -- I've tested 4096KB I/O requests with no problems.
I looked through the DMA paths on the hardware drivers to ensure they
could take advantage of the SG chaining, and it seems that every one
except ipath uses the system's DMA routines, which have been converted
to handle chaining. ipath looks like it should be OK, but I have no
way to test it.
Signed-off-by: David Dillow <dillowda@ornl.gov>
[ Tested on ipath. - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The current SRP initiator will send requests even if it has no credits
available. The results of sending extra requests are vendor specific,
but on some devices, overrunning credits will cost 85% of peak
performance -- e.g. 100 MB/s vs 720 MB/s. Other devices may just drop
the requests.
This patch will tell the SCSI midlayer to queue requests if there are
fewer than two credits remaining, and will not issue a task management
request if there are no credits remaining. The mid-layer will retry
the queued command once an outstanding command completes.
The patch also removes the unlikely() in __srp_get_tx_iu(), as it is
not at all unlikely to hit this limit under heavy load.
Signed-off-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
An IPoIB subnet on an IB fabric that spans multiple IB subnets can't
use link-local scope in multicast GIDs. The existing routines that
map IP/IPv6 multicast addresses into IB link-level addresses hard-code
the scope to link-local, and they also leave the partition key field
uninitialised. This patch adds a parameter (the link-level broadcast
address) to the mapping routines, allowing them to initialise both the
scope and the P_Key appropriately, and fixes up the call sites.
The next step will be to add a way to configure the scope for an IPoIB
interface.
Signed-off-by: Rolf Manderscheid <rvm@obsidianresearch.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Signed-off-by: Oliver Pinter <oliver.pntr@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Signed-off-by: Erez Zilber <erezz@voltaire.com>
|
|
Add missing spaces in the middle of format strings.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|