aboutsummaryrefslogtreecommitdiff
path: root/drivers/media/dvb/firewire
AgeCommit message (Collapse)Author
2009-10-01const: constify remaining file_operationsAlexey Dobriyan
[akpm@linux-foundation.org: fix KVM] Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Acked-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-12V4L/DVB (12583): firedtv: combine some debug logging codeStefan Richter
Shrinks source and kernel object size a bit. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-09-12V4L/DVB (12582): The current AVC debugging can clog the log down a lot since ↵Henrik Kurelid
many applications tend to check the signal strength very often. This patch enables users to select which AVC messages to log using a bitmask. In addition, it also enables the possibility to debug application PMTs sent to the driver. This will be usable since the CA support is still poorly tested for lots of CAMs and CA systems. Signed-off-by: Henrik Kurelid <henrik@kurelid.se> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-09-12V4L/DVB (12482): firedtv: add PID filtering for SW zigzag retuneHenrik Kurelid
The AVC protocol uses the same command for tuning and PID filtering and since dvb-core uses a software zigzagging to do automatic retuning this could cause all PID filters to be cleared. PID filter information is now included in all DSD commands to the card. Background: There is a problem in the firedtv driver that causes recordings to stop if the SW zigzag algorithm in dvb-core kicks in with a retune after the application has set up the PID filters. Since tuning and setting PID filters uses the same AVC command (DSD) and only the replace subfunction is supported by the card, it is not possible to do a retune without setting the PID filters. This means that the PID filtering has to be sent in each tune. This problem applies to C and T cards since S and S2 cards tune using a vendor specific command. The patch corrects the problem by sending the PID list in each tune. I have tested it on my T card with a good result. How to trigger problem: Zap to a channel and output AV to a file, e.g. "tzap -c channels.conf SVT1 -r -o SVT1.ts". After a short while, pull the antenna cable from the card. The lock on the channel will disappear and the TS file will stop increasing in size. Wait a couple of seconds. Replug the cable again. You will get a lock on the channel again, but the TS file will never increase in size agains sinze no PIDS are filtered. Tested with kaffeine with DVB-T and DVB-C: Fixes retuning after antenna was plugged out and back in with DVB-T. Does not fix this with DVB-C, but also doesn't regress on DVB-C. Signed-off-by: Henrik Kurelid <henrik@kurelid.se> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-16V4L/DVB (11739): remove driver_data direct access of struct deviceGreg Kroah-Hartman
In the near future, the driver core is going to not allow direct access to the driver_data pointer in struct device. Instead, the functions dev_get_drvdata() and dev_set_drvdata() should be used. These functions have been around since the beginning, so are backwards compatible with all older kernel versions. Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-16V4L/DVB (11724): firedtv: Storage class should be before const qualifierTobias Klauser
The C99 specification states in section 6.11.5: The placement of a storage-class specifier other than at the beginning of the declaration specifiers in a declaration is an obsolescent feature. Signed-off-by: Tobias Klauser <tklauser@distanz.ch> Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-04-06Revert "V4L/DVB (10962): fired-avc: fix printk formatting warning."Stefan Richter
Commit 34aecd2851bba5c2b7dae2f0dbe8e629b1c5e4ac was made obsolete and invalid by commit 40cf65d149053889c8876c6c2b4ce204fde55baa. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-03-30V4L/DVB (10962): fired-avc: fix printk formatting warning.Hans Verkuil
size_t should be printed with %zu. Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-03-27DVB: firedtv: FireDTV S2 problems with tuning solvedBeat Michel Liechti
Signed-off-by: Beat Michel Liechti <bml303@gmail.com> Tuning was broken on FireDTV S2 (and presumably FloppyDTV S2) because a wrong opcode was sent. The box only gave "not implemented" responses. Changing the opcode to _TUNE_QPSK2 fixes this for good. Cc: stable@kernel.org Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2009-03-24DVB: firedtv: fix printk format mismatchStefan Richter
Eliminate drivers/media/dvb/firewire/firedtv-avc.c: In function 'debug_fcp': drivers/media/dvb/firewire/firedtv-avc.c:156: warning: format '%d' expects type 'int', but argument 5 has type 'size_t' Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2009-02-24firedtv: dvb_frontend_info for FireDTV S2, fix "frequency limits undefined" ↵Beat Michel Liechti
error I found that the function fdtv_frontend_init in the file firedtv-fe.c was missing a case for FIREDTV_DVB_S2 which resulted in "frequency limits undefined" errors in syslog. Signed-off-by: Beat Michel Liechti <bml303@gmail.com> Change by Stefan R: combine it with case case FIREDTV_DVB_S as originally suggested by Beat Michel. This enables FE_CAN_FEC_AUTO also for FireDTV-S2 devices which is possible as long as only DVB-S channels are used. FE_CAN_FEC_AUTO would be wrong for DVB-S2 channels, but those cannot be used yet since the driver is not yet converted to S2API. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2009-02-24firedtv: massive refactoringStefan Richter
Combination of the following changes: Mon, 23 Feb 2009 14:21:10 +0100 (CET) firedtv: reinstate debug logging option Henrik Kurelid tells me that FCP debug logging (which I removed during cleanups) is still useful when working on driver issues together with end users. So bring it back in an updated form with only 60% of the original code footprint. Logging can be enabled with # echo -1 > /sys/module/firedtv/parameters/debug 1 instead of -1 enables only FCP header logging, 2 instead of -1 enables only hexdumps of the entire FCP frames. 0 switches logging off again. Fri, 20 Feb 2009 20:54:27 +0100 (CET) firedtv: build fix for INPUT=m and DVB_FIREDTV=y Thu, 19 Feb 2009 20:40:39 +0100 firedtv: use msecs_to_jiffies Pointed out by Mauro Carvalho Chehab. Sun Feb 15 20:50:46 CET 2009 firedtv: some more housekeeping Fix an old checkpatch warning and a new compiler warning. Sun Feb 15 15:33:17 CET 2009 firedtv: rename a file once more At the moment, about a third of avc.c is specific to FireDTVs rather than generic AV/C code. Rename it to firedtv-avc.c. Sun Feb 15 15:33:17 CET 2009 firedtv: dvb demux: more compact channels backing store Replace struct firedtv_channel { bool active; int pid; } channel[16]; by unsigned long channel_active; u16 channel_pid[16];. Sun Feb 15 15:33:17 CET 2009 firedtv: dvb demux: some simplifications c->active was unnecessarily cleared twice. Also, by marking the channel inactive before the for loop, the loop becomes identical with fdtv_channel_collect(). Sun Feb 15 15:33:17 CET 2009 firedtv: dvb demux: remove a bogus loop This loop is unnecessary because - only active channel[].pid's will be sent to the device, - when a channel is activated, its pid is set to dvbdmxfeed->pid. Perhaps the original code was there because it was initially not fully covered by the fdtv->demux_mutex. Sun Feb 15 15:33:17 CET 2009 firedtv: dvb demux: fix mutex protection fdtv_start_feed() accessed the channel list unsafely. Fully serialize it with itself and fdtv_stop_feed(). Sun Feb 15 15:33:17 CET 2009 firedtv: dvb demux: fix missing braces Original code was: ... case DMX_TS_PES_OTHER: //Dirty fix to keep firesat->channel pid-list up to date for(k=0;k<16;k++){ if(firesat->channel[k].active == 0) firesat->channel[k].pid = dvbdmxfeed->pid; break; } channel = firesat_channel_allocate(firesat); break; default: ... Looks bogus in several respects. For now let's just add braces to the if because that seems to be what the author meant. Sun Feb 15 15:33:17 CET 2009 firedtv: allow build without input subsystem !CONFIG_INPUT is very unlikely on systems on which firedtv is of interest. But we can easily support it. Sun Feb 15 15:33:17 CET 2009 firedtv: replace EXTRA_CFLAGS by ccflags The former are deprecated. The latter can depend on Kconfig variables. Sun Feb 15 15:33:17 CET 2009 firedtv: concentrate ieee1394 dependencies Move the entire interface with drivers/ieee1394 to firedtv-1394.c. Move 1394-independent module initialization code to firedtv-dvb.c. This prepares interfacing with drivers/firewire. Sun Feb 15 15:33:17 CET 2009 firedtv: amend Kconfig menu prompt Sun Feb 15 15:33:17 CET 2009 firedtv: remove kernel version compatibility macro Sun Feb 15 15:33:17 CET 2009 firedtv: combine header files avc.h and firedtv-*.h are small and currently not shared with other drivers, hence concatenate them all into firedtv.h. Sun Feb 15 15:33:17 CET 2009 firedtv: misc style touch-ups Standardize on lower-case hexadecimal constants. Adjust whitespace. Omit unnecessary pointer type casts and an unnecessary list head initialization. Use dev_printk. Wed Feb 11 21:21:04 CET 2009 firedtv: avc, ci: remove unused constants Wed Feb 11 21:21:04 CET 2009 firedtv: avc: remove bitfields from read descriptor response operands Don't use bitfields in struct types of on-the-wire data. Wed Feb 11 21:21:04 CET 2009 firedtv: avc: remove bitfields from DSD command operands Don't use bitfields in struct types of on-the-wire data. Wed Feb 11 21:21:04 CET 2009 firedtv: avc: header file cleanup Remove unused constants and declarations. Move privately used constants into .c files. Wed Feb 11 21:21:04 CET 2009 firedtv: avc: remove bitfields from FCP frame types Don't use bitfields in struct types of on-the-wire data. Also move many privately used constants from avc.h to avc.c and remove some unused constants. Sun, 18 Jan 2009 16:30:00 +0100 (CET) firedtv: avc: fix offset in avc_tuner_get_ts The parentheses were wrong. It didn't matter though because this code only writes a 0 into an area which is already initialized to 0. Sun, 18 Jan 2009 16:30:00 +0100 (CET) firedtv: avc: reduce stack usage, remove two typedefs It is safe to share a memory buffer for command frame and response frame because the response data come in after the command frame was last used. Even less stack would be required if only the actual required frame size instead of the entire FCP register size was allocated. Also, rename the defined types AVCCmdFrm and AVCRspFrm to struct avc_command_frame and struct avc_response_frame. TODO: Remove the bitfields in these types. Sun, 18 Jan 2009 16:30:00 +0100 (CET) firedtv: cmp: move code to avc Sun, 18 Jan 2009 16:30:00 +0100 (CET) firedtv: iso: move code to firedtv-1394 Sun, 18 Jan 2009 16:30:00 +0100 (CET) firedtv: iso: remove unnecessary struct type definitions Sun, 18 Jan 2009 16:30:00 +0100 (CET) firedtv: iso: style changes and fixlets Add cleanup after failure in setup_iso_channel. Replace printk() by dv_err(). Decrease indentation level in rawiso_activity_cb(). Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2009-02-24firedtv: rename files, variables, functions from firesat to firedtvRambaldi
Combination of the following changes: Sat, 17 Jan 2009 14:47:34 +0100 firedtv: rename variables and functions from firesat to firedtv Signed-off-by: Rambaldi <Rambaldi@xs4all.nl> Additional changes by Stefan Richter: Renamed struct firedtv *firedtv to struct firedtv *fdtv and firedtv_foo_bar() to fdtv_foo_bar() for brevity. Sat, 17 Jan 2009 13:07:44 +0100 firedtv: rename files from firesat to firedtv Signed-off-by: Rambaldi <Rambaldi@xs4all.nl> Additional changes by Stefan Richter: Name the directory "firewire" instead of "firedtv". Standardize on "-" instead of "_" in file names, because that's what drivers/firewire/ and drivers/media/dvb/dvb-usb/ use too. Build fix. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>