| Age | Commit message (Collapse) | Author |
|---|
|
disappear.
Since i2c autoprobing will disappear bttv needs to be converted to use
v4l2_subdev instead.
Without autoprobing the autoload module option has become obsolete. A warning
is generated if it is set, but it is otherwise ignored.
Since the bttv card definitions are of questionable value a new option was
introduced to allow the user to control which audio module is selected:
msp3400, tda7432 or tvaudio (or none at all).
By default bttv will use the card definitions and fallback on tvaudio as the
last resort.
If no audio device was found a warning is printed.
The saa6588 RDS device is now also explicitly probed since it is no longer
possible to autoprobe it. A new saa6588 module option was added to override
the card definition since I suspect more cards have this device than one
would guess from the card definitions.
Note that the probe addresses of the i2c modules are hardcoded in this
driver. Once all v4l drivers are converted to v4l2_subdev this will be
cleaned up. Such data belongs in an i2c driver header.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Add support for ProVideo PV-183 to bttv
This patch adds support for the ProVideo PV-183 card to the bttv
device driver. The PV-183 is a PCI card with 8 BT878 devices plus a Hint
Corp HiNT HB4 PCI-PCI Bridge. Each BT878 has two composite input channels
available. There are no tuners on this card.
Signed-off-by: Alan McIvor <alan.mcivor@reveal.co.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
I have a GeoVision GV-800(S) card, it has 4 CONEXANT BT878A chips.
It has 16 video inputs and 4 audio inputs, and it is almost identical
to the GV-800, as seen on http://bttv-gallery.de .
The only difference appears to be the analog mux, it has a CD22M3494
in place of the MT8816AP. The card has a blue PCB, as seen in this
picture: http://www.gsbr.com.br/imagem/kits/GeoVision%20GV%20800.jpg .
This card wasn't originally supported, and it was detected as
UNKNOWN/GENERIC. The video inputs weren't working, so I tried
"forcing" a few cards like the GeoVision GV-600, but there was still
no video. So I made a patch to support this card, based on the Kodicom
4400r.
The GV-800(S) is identified as follows:
...
02:00.0 Multimedia video controller: Brooktree Corporation Bt878 Video
Capture (rev 11)
02:00.1 Multimedia controller: Brooktree Corporation Bt878 Audio
Capture (rev 11)
02:04.0 Multimedia video controller: Brooktree Corporation Bt878 Video
Capture (rev 11)
02:04.1 Multimedia controller: Brooktree Corporation Bt878 Audio
Capture (rev 11)
02:08.0 Multimedia video controller: Brooktree Corporation Bt878 Video
Capture (rev 11)
02:08.1 Multimedia controller: Brooktree Corporation Bt878 Audio
Capture (rev 11)
02:0c.0 Multimedia video controller: Brooktree Corporation Bt878 Video
Capture (rev 11)
02:0c.1 Multimedia controller: Brooktree Corporation Bt878 Audio
Capture (rev 11)
...
02:00.0 0400: 109e:036e (rev 11)
Subsystem: 800a:763d
Flags: bus master, medium devsel, latency 32, IRQ 10
Memory at cdfff000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data <?>
Capabilities: [4c] Power Management version 2
Kernel modules: bttv
02:00.1 0480: 109e:0878 (rev 11)
Subsystem: 800a:763d
Flags: bus master, medium devsel, latency 32, IRQ 10
Memory at cdffe000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data <?>
Capabilities: [4c] Power Management version 2
02:04.0 0400: 109e:036e (rev 11)
Subsystem: 800b:763d
Flags: bus master, medium devsel, latency 32, IRQ 10
Memory at cdffd000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data <?>
Capabilities: [4c] Power Management version 2
Kernel modules: bttv
02:04.1 0480: 109e:0878 (rev 11)
Subsystem: 800b:763d
Flags: bus master, medium devsel, latency 32, IRQ 10
Memory at cdffc000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data <?>
Capabilities: [4c] Power Management version 2
02:08.0 0400: 109e:036e (rev 11)
Subsystem: 800c:763d
Flags: bus master, medium devsel, latency 32, IRQ 10
Memory at cdffb000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data <?>
Capabilities: [4c] Power Management version 2
Kernel modules: bttv
02:08.1 0480: 109e:0878 (rev 11)
Subsystem: 800c:763d
Flags: bus master, medium devsel, latency 32, IRQ 10
Memory at cdffa000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data <?>
Capabilities: [4c] Power Management version 2
02:0c.0 0400: 109e:036e (rev 11)
Subsystem: 800d:763d
Flags: bus master, medium devsel, latency 32, IRQ 10
Memory at cdff9000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data <?>
Capabilities: [4c] Power Management version 2
Kernel modules: bttv
02:0c.1 0480: 109e:0878 (rev 11)
Subsystem: 800d:763d
Flags: bus master, medium devsel, latency 32, IRQ 10
Memory at cdff8000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data <?>
Capabilities: [4c] Power Management version 2
As you can see, the GV-800(S) card is almost identical to the GV-800
on bttv-gallery, so this patch might also work for that card. If not,
only a few changes should be required on the gv800s_write() function.
After this patch, the video inputs work correctly on linux 2.6.24 and
2.6.27 using the software 'motion'. The input order may seem a little
odd, but it's the order the original software/driver uses, and I decided
to keep that order to get the most out of the card.
I tried to get the audio working with the snd-bt87x module, but I only
get noise from every audio input, even after selecting a different mux
with alsamixer. Also, after trying to play sound from those sources, I
randomly get a RISC error about an invalid RISC opcode, and then that
output stops working. I also can't change the sampling rate when
recording. Any pointers to adding audio support are welcome.
Signed-off-by: Bruno Christo <bchristo@inf.ufsm.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Over half of the card database was used to store muxsel data. 64 bytes
were used to store one 32 bit word for each of up to 16 inputs.
The Bt8x8 only has two bits to control its mux, so muxsel data for 16
inputs will fit into a single 32 bit word. There were a couple cards that
had special muxsel data that didn't fit in two bits, but I cleaned them up
in earlier patches.
Unfortunately, C doesn't allow us to have an array of bit fields. This
makes initializing the structure more of a pain. But with some cpp magic,
we can do it by changing:
.muxsel = { 2, 3, 0, 1 },
.muxsel = { 2, 2, 2, 2, 3, 3, 3, 3, 1, 1 },
Into:
.muxsel = MUXSEL(2, 3, 0, 1),
.muxsel = MUXSEL(2, 2, 2, 2, 3, 3, 3, 3, 1, 1),
That's not so bad. MUXSEL is a fancy macro that packs the arguments (of
which there can be one to sixteen!) into a single word two bits at a time.
It's a compile time constant (a variadic function wouldn't be) so we can
use it to initialize the structure. It's important the the arguments to
the macro only be plain decimal integers. Stuff like "0x01", "(2)", or
"MUX3" won't work properly.
I also created an accessor function, bttv_muxsel(btv, input), that gets the
mux bits for the selected input. It makes it cleaner to change the way the
muxsel data is stored.
This patch doesn't change the code size and decreases the datasegment by
9440 bytes.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The code was using a muxsel value of -1U to indicate a digital input. A
couple places in were checking of muxsel < 0 to detect this, which doesn't
work of course because muxsel is unsigned and can't be negative.
Only a couple cards had digital inputs and it was always the last one, so
for the card database create a one bit field that indicates the last input
is digital. On init, this is used to set a new field in the bttv struct to
the digital input's number or UNSET for none. This makes it easier to
check if the current input is digital.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The bttv card database is quite large and the data structure used to store
it wasn't very efficient. Most of the field are only used at card
initialization time so it doesn't matter if they aren't efficient to
access.
Overall the changes reduce code size by 60 bytes in ia32. The data size is
decreased by 5024 byes. It is probably even more for 64-bit kernels.
Move the fields in the struct around to be sorted from largest to smallest.
This saves on padding space used for alignment.
Get rid of the unused digital_mode field. Leave the setting as a comment
in the few cards entries that set it, in case someone ever writes the code.
Get rid of the unused audio_inputs field. Leave the values in the card
entries in case someone ever writes code that might use it.
Get ride of the unused radio_addr field. No card entries even set it to
anything interesting so it's not left as comments. All the code that used
it was removed in commit v2.6.14-3466-g291d1d7 from Nov 8th 2005.
Reduce video_inputs to u8 as no card has more than 255 inputs (the most is
16).
Change tuner_addr to u8. I2C addresses are only seven bits and 255 means
ADDR_UNSET, so everything fits.
Make has_radio a one bit flag.
Make the pll setting a two bit field.
Reduce svhs to four bits as no card has an s-video input above 9. Change
the value for no s-video input from UNSET (which is -1U and out of range of
four bits) to NO_SVHS (which is now 15).
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The bttv card database structure had a "tuner" field that was the input
number of the tuner input or UNSET for no tuner. However, the only values
it could ever be are 0 and UNSET. Having a tuner on an input other than 0
didn't work and was never used.
There is also a "tuner_type" field that can be set to TUNER_ABSENT to
indicate no tuner, which makes "tuner = UNSET" redundant. In many cases,
tuner_type was set to UNSET when there was no tuner, which isn't quite
correct. tuner_type == UNSET is supposed to mean the tuner type isn't yet
known.
So, I changed cards where "tuner == UNSET" to always have tuner_type of
TUNER_ABSENT. At this point the tuner field is redundant, so I deleted it.
I have the card setup code set the card's tuner_type (not the card type's
tuner_type!) to TUNER_ABSENT if it hasn't yet been set at the end of the
setup code. Various places that check if the card has a tuner will now
look for this instead of checking the card type's "tuner" field.
Also autoload the tuner module before issuing the TUNER_SET_TYPE_ADDR I2C
client call instead of after issuing it.
Overall, on ia32 this decreases compiled code size by about 24 bytes and
reduces the data size by 640 bytes.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The code to set the norm for the TDA9880 analog demod was comparing
btv->norm, an index into the bttv driver's norm array, to V4L2_STD_NTSC,
which is a bit flag that's part of the V4L2 API. This doesn't work of
course and results in the PAL path always being taken.
What's more, it modified the bttv_tvcards[] entries for cards using the
TDA9880. This is wrong because changing the norm on one card will also
affect other cards of the same type. Writing to bttv_tvcards is also bad
because it should be read-only or even devinitdata.
Changing the norm would also cause the audio to become unmuted.
Have the code get called for both norm setting and audio input setting
(which where the gpios are set) to avoid needed to modify bttv_tvcards.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The norm value in the driver is an index into an array and the the driver
doesn't allow it to be negative or otherwise invalid. It should be
unsigned but wasn't in all places.
Fix some structs and functions to have the norm be unsigned. Get rid of
useless checks for "< 0". Most of the driver code can't handle a norm
value that's out of range, so change some ">= BTTV_TVNORMS" checks to
BUG_ON(). There's no point in silently ignoring invalid driver state just
to crash because of it later.
Reported-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
It's a quad Bt878 PCI-e x1 capture board that's basically the same as the
IVC-200 (quad Bt878 PCI) capture board that's currently supported in
the V4L2 bttv driver.
Manufacturer's web page for IVCE-8784 with photo and info:
http://www.iei.com.tw/en/product_IPC.asp?model=IVCE-8784
Signed-off-by: Douglas Kosovic <douglask@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This Patch does modify the bttv-cards.c and bttc.h so that the driver
supports VD-011, VD-012, VD-012-X1 and VD-012-X2 Framegrabber from
Phytec Messtechnik GmbH.
Signed-off-by: Dirk Heer <d.heer@phytec.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
dev_set_name()
This patch is part of a larger patch series which will remove
the "char bus_id[20]" name string from struct device. The device
name is managed in the kobject anyway, and without any size
limitation, and just needlessly copied into "struct device".
To set and read the device name dev_name(dev) and dev_set_name(dev)
must be used. If your code uses static kobjects, which it shouldn't
do, "const char *init_name" can be used to statically provide the
name the registered device should have. At registration time, the
init_name field is cleared, to enforce the use of dev_name(dev) to
access the device name at a later time.
We need to get rid of all occurrences of bus_id in the entire tree
to be able to enable the new interface. Please apply this patch,
and possibly convert any remaining remaining occurrences of bus_id.
We want to submit a patch to -next, which will remove bus_id from
"struct device", to find the remaining pieces to convert, and finally
switch over to the new api, which will remove the 20 bytes array
and does no longer have a size limitation.
Thanks,
Kay
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Thanks to Sistema Fenix (http://www.sistemafenix.com.br/) and CDI Brasil
(www.cdibrasil.com.br/) for sponsoring this development.
Signed-off-by: Gilberto <gilberto@sistemafenix.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Also remove some blank lines that were used to split compat code at -devel
tree.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Convert dvb-bt8xx to use tuner-simple instead of dvb-pll for Philips FCV1236D
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Signed-off-by: Mauro Lacy <mauro@lacy.com.ar>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
I have what looks like a Geovision GV-600 (or 650) card. It has a large
chip in the middle labeled
CONEXANT
FUSION 878A
25878-13
E345881.1
0312 TAIWAN
It has an audio connector coming out from a chip labeled
ATMEL
0242
AT89C2051-24PI
It is identified as follows on my Debian GNU/Linux Etch (kernel 2.6.18)
...
01:0a.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
01:0a.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
...
01:0a.0 0400: 109e:036e (rev 11)
Subsystem: 008a:763c
Flags: bus master, medium devsel, latency 64, IRQ 58
Memory at dfffe000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
01:0a.1 0480: 109e:0878 (rev 11)
Subsystem: 008a:763c
Flags: bus master, medium devsel, latency 64, IRQ 58
Memory at dffff000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
It was being detected as a GENERIC UNKNOWN CARD both by the 2.6.18
kernel and the latest v4l-dvb drivers, but it did not work at all. The
card has sixteen (16) BNC video inputs, four of them on the board itself
and twelve on three daughter-cards. It has a single bt878 chip, no tuner
and what looks like and audio input. After doing some research I managed
to get only eight channels working by forcing card=125 and those DID NOT
match channels 0-7 on the card, and no audio.
Based on what was working for card=125, I added the card definition
block, added a specific muxsel routine and got the card working fully
with xawtv, where the sixteen channels show up as Composite0 to
Composite15, matching the channel labels in the card and daughter-cards.
I have made no efforts yet to get audio working, but would appreciate
any pointers.
Signed-off-by: Ernesto Hernández-Novich <emhn@usb.ve>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Also convert audio_mode_gpio functions from audio_hook
Signed-off-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Adds an entry for the Typhoon Tv-Tuner PCI to bttv-cards.c
Signed-off-by: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
add analog video support for DViCO FusionHDTV 2
Thanks to Todd Ignasiak for donating the card.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Fix support for 3dfx Voodoo TV 200 variant
Signed-off-by: Wade Berrier <wberrier@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
SSAI (www.ssai.us) makes several Bt878-based capture cards that get used in our
surveillance, conferencing, and medical imaging systems. The attached
relatively small patch adds support for these cards, which fall into two broad
* boards with one or more Bt878s, one or more composite inputs, and no S-video
or tuner inputs
* boards with one Bt878, one composite input, one S-video input, and no tuner
input
Signed-off-by: Scott Alfter <salfter@ssai.us>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
This patch contains the following possible cleanups:
- remove the following unused global functions:
- bttv-if.c: bttv_get_cardinfo()
- bttv-if.c: bttv_get_id()
- bttv-if.c: bttv_get_gpio_queue()
- bttv-if.c: bttv_i2c_call()
- remove the following unused EXPORT_SYMBOL's:
- bttv-gpio.c: bttv_sub_bus_type
- bttv-gpio.c: bttv_gpio_inout
- bttv-gpio.c: bttv_gpio_read
- bttv-gpio.c: bttv_gpio_write
- bttv-gpio.c: bttv_gpio_bits
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Besides adding the board specific code, this patch moves
the RC5 decoding code from bt8xx to ir-functions.c to make it available
for all drivers.
Signed-off-by: Marc Fargas <telenieko.telenieko.com>
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
This functionality was used when remote control input for BTTV was handled
by a standalone module, to hook some functions of that module into the main
bttv core.
Since that module is now extinct, this can go away
Signed-off-by: Ricardo Cerqueira <rmcc@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Cleanup audio input handling in bttv and tvaudio:
- inputs were specified that were never used
- mute was handled as a special input which led to confusing code
- confusing naming made it difficult to see if the setting was for
i2c or gpio.
The old audiochip.h input names moved to tvaudio.h. Currently this
is used both by tvaudio and msp3400 until the msp3400 implements the
new msp3400-specific inputs.
Detect in bttv the tvaudio and msp3400 i2c clients and use these
client pointers to set the inputs directly instead of broadcasting the
command.
Removed AUDC_SET_INPUT. Now replaced by VIDIOC_S_AUDIO. This will be
replaced again later by the new ROUTING commands.
Removed VIDIOC_G_AUDIO implementations in i2c drivers: this command is
a user level command and not to be used internally. It wasn't called at
all anyway.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
- Missing a Makefile for bt8xx
- rds.h were at wrong directory, since it is a global header for an internal
interface
- tda7432 and tda9875 were dependent from bttv.h
- bttv.h were holding i2c addresses
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
