aboutsummaryrefslogtreecommitdiff
path: root/drivers/mmc/host/atmel-mci-regs.h
AgeCommit message (Collapse)Author
2009-06-13atmel-mci: add MCI2 register definitionsNicolas Ferre
New revision of Atmel MCI interface adds new features. This is a update of register definition in header file. This new MCI IP is called MCI2. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13atmel-mci: Integrate AT91 specific definition in header fileNicolas Ferre
The MCI IP is shared among AVR32 and AT91 SOCs. AT91 has specific bit definitions in the user interface of MCI SD/MMC IP. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2008-10-05atmel-mci: Platform code for supporting multiple mmc slotsHaavard Skinnemoen
Add the necessary platform infrastructure to support multiple mmc/sdcard slots all at once through a single controller. Currently, the driver will use the first valid slot it finds and stick with that, but later patches will add support for switching between several slots on the fly. Extend the platform data structure with per-slot information: MMC/SDcard bus width and card detect/write protect pins. This will affect the pin muxing as well as the capabilities announced to the mmc core. Note that board code is now required to supply a mci_platform_data struct to at32_add_device_mci(). Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-07-27atmel-mci: debugfs supportHaavard Skinnemoen
Create additional files under the host's debugfs directory containing additional host-specific debug information. Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-07-15atmel-mci: Driver for Atmel on-chip MMC controllersHaavard Skinnemoen
This is a driver for the MMC controller on the AP7000 chips from Atmel. It should in theory work on AT91 systems too with some tweaking, but since the DMA interface is quite different, it's not entirely clear if it's worth merging this with the at91_mci driver. This driver has been around for a while in BSPs and kernel sources provided by Atmel, but this particular version uses the generic DMA Engine framework (with the slave extensions) instead of an avr32-only DMA controller framework. This driver can also use PIO transfers when no DMA channels are available, and for transfers where using DMA may be difficult or impractical for some reason (e.g. the DMA setup overhead is usually not worth it for very short transfers, and badly aligned buffers or lengths are difficult to handle.) Currently, the driver only support PIO transfers. DMA support has been split out to a separate patch to hopefully make it easier to review. The driver has been tested using mmc-block and ext3fs on several SD, SDHC and MMC+ cards. Reads and writes work fine, with read transfer rates up to 3.5 MiB/s on fast cards with debugging disabled. The driver has also been tested using the mmc_test module on the same cards. All tests except 7, 9, 15 and 17 succeed. The first two are unsupported by all the cards I have, so I don't know if the driver handles this correctly. The last two fail because the hardware flags a Data CRC Error instead of a Data Timeout error. I'm not sure how to deal with that. Documentation for this controller can be found in many data sheets from Atmel, including the AT32AP7000 data sheet which can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>