| Age | Commit message (Collapse) | Author |
|---|
|
The driver is selectable on other than Au1200 Alchemy systems but won't
build nor work - there is no MMC hw.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
md->disk was being used in a debug message before it was allocated.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
command and cleanups
Patch from Pavel Pisa
There has been problems that for some paths that clock are not stopped
during new command programming and initiation. Result is issuing
of incorrect command to the card. Some other problems are cleaned too.
Noisy report of known ERRATUM #4 has been suppressed.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Rather than having every driver duplicate the set_ios debugging,
provide a single version in mmc.c which can be expanded as we
add additional functionality.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
mmc_request_done should be called at the end of handling a request, not
between the data and initial command parts of the request.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
There's no reason for the PXAMCI debug code to print so many lines - it
causes the kernel buffer to overflow when trying to debug this driver.
Remove some debug messages which are duplicated by core code, and
combine other messages, resulting in fewer characters written to the
kernel log.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Always send a stop command at the end of a data transfer. If we avoid
sending the stop command, some cards remain in data transfer mode, and
refuse to accept further read/write commands.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The CSD contains a "read2write factor" which determines the multiplier to
be applied to the read timeout to obtain the write timeout. We were
ignoring this parameter, resulting in the possibility for writes being
timed out too early.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Patch from Pavel Pisa
The clock starting imxmci_start_clock() function contains hardware
issue workaround, which repeats start attempt, if SDHC does not react on
the first trial. But the second start attempt can be taken even, if the
first succeed and test code misses time limited clock running phase
due to delay caused by schedule to other task or some another device
interrupt. This change enables to detect such situation.
The performance is not issue, because usually at full clock rate
only about six loops in delay cycle are needed.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The MMC layer gives us two parts for the timeout calculation - a fixed
timeout in nanoseconds, and a card clock-speed dependent part.
The PXA MMC hardware allows for a timeout based on the fixed host clock
speed only. This resulted in some cards being given a short timeout,
and therefore failing to work.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Patch from Pavel Pisa
This patch adds support of i.MX/MX1 SD/MMC controller.
It has been significantly redesigned from the original Sascha Hauer's
version to support scatter-gather DMA, to conform to latest Pierre Ossman's
and Russell King's MMC-SD Linux 2.6.x infrastructure.
The handling of all events has been moved to the softirq context
and is designed with no busy-looping in mind. Unfortunately
some controller bugs has to be overcome by limited looping
about 2-20 usec but these are observed only for initial card
recognition phase.
There are still some missing/missed IRQs problems under heavy load.
Help of somebody with access to the full SDHC design information
is probably necessary.
Regenerated against 2.6.16-git-060402 to solve clash with other patches.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Patch from Andrew Victor
This patch adds support for the MMC/SD card interface on the Atmel
AT91RM9200 processor.
Original driver was by Nick Randell, but a number of people have
subsequently worked on it. It's currently maintained by Malcolm Noyes.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Rather than each driver test MMC_DEBUG itself, and define DEBUG,
pass it in via the makefile instead.
Fix drivers to use pr_debug() where appropriate, and avoid defining
a DEBUG() macro.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Adds OMAP MMC driver.
Signed-off-by: Juha Yrjölä <juha.yrjola@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Carlos Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
MODULE_PARM was actually breaking: recent gcc version optimize them out as
unused. It's time to replace the last users, which are generally in the
most unloved drivers anyway.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Driver for the Secure Digital Host Controller Interface specification.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
platform_get_irq*() now returns on -ENXIO when the resource cannot be
found. Ensure all users of platform_get_irq*() handle this error
appropriately.
Signed-off-by: David Vrabel <dvrabel@arcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Fix a trivial compilation warning:
CC drivers/mmc/au1xmmc.o
drivers/mmc/au1xmmc.c: In function ‘au1xmmc_dma_callback’:
drivers/mmc/au1xmmc.c:743: warning: unused variable ‘status’
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
drivers/mmc/au1xmmc.c doesn't compile because commit
e92251762d02a46177d4105d1744041e3f8bc465 introduced a typo and passes
the wrong argument to the mmc_resp_type macro.
Error because of the typo:
CC drivers/mmc/au1xmmc.o
drivers/mmc/au1xmmc.c: In function ‘au1xmmc_send_command’:
drivers/mmc/au1xmmc.c:197: warning: implicit declaration of function ‘mmc_rsp_type’
...
LD .tmp_vmlinux1
drivers/built-in.o: In function `au1xmmc_request':au1xmmc.c:(.text+0x89504): undefined reference to `mmc_rsp_type'
:au1xmmc.c:(.text+0x8968c): undefined reference to `mmc_rsp_type'
make: *** [.tmp_vmlinux1] Error 1
Error because of the wrong argument:
CC drivers/mmc/au1xmmc.o
drivers/mmc/au1xmmc.c: In function ‘au1xmmc_send_command’:
drivers/mmc/au1xmmc.c:197: error: invalid type argument of ‘->’
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
drivers/mmc/au1xmmc.c currently doesn't compile; it needs to be
converted to use platform_driver. I cannot test this change because
of lack of hardware but I followed the drivers this one is based on,
and the code is certainly not worse than before.
drivers/mmc/au1xmmc.c: At top level:
drivers/mmc/au1xmmc.c:1002: error: ‘platform_bus_type’ undeclared here (not in a function)
make[2]: *** [drivers/mmc/au1xmmc.o] Error 1
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
If a data transfer is small (less than a FIFO size) we would
hang waiting for the data to be read due to the PIO interrupt
not occuring. We allowed for this in our PIO interrupt handler,
but not when setting up a data transfer.
Apply the "fix" when setting up a data transfer as well.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
An obvious vi fat finger on my part.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Some hosts need to know the command type, so pass it via a set of
flags in cmd->flags.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
|
|
drivers/mmc/mmc_block.c: In function `mmc_blk_probe':
drivers/mmc/mmc_block.c:467: warning: long unsigned int format, different type arg (arg 5)
We don't know what size sector_t is - cast it.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
convert mfd and mmc to mutexes
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
|
|
Some hosts need to know that a transfer will be multi-block.
Add a data flag to indicate multiple data block transfers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
HDIO_GETGEO is implemented in most block drivers, and all of them have to
duplicate the code to copy the structure to userspace, as well as getting
the start sector. This patch moves that to common code [1] and adds a
->getgeo method to fill out the raw kernel hd_geometry structure. For many
drivers this means ->ioctl can go away now.
[1] the s390 block drivers are odd in this respect. xpram sets ->start
to 4 always which seems more than odd, and the dasd driver shifts
the start offset around, probably because of it's non-standard
sector size.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@suse.de>
Cc: <mike.miller@hp.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Fix the coding style in the wbsd driver once and for all.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Version 4 of the MMC specification increased the version number of the
CID structure. None of the fields changed though so the only required
change is adding '4' to the approved list.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Allow the wbsd driver to use the new suspend/resume functions added to
the PnP layer.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
|
|
|
|
This is needs to be visible to other architectures using the AMBA
bus and peripherals.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
|
|
Since the ARM AMBA bus is used on MIPS as well as ARM, we need
to make the bus available for other architectures to use. Move
the AMBA include files from include/asm-arm/hardware/ to
include/linux/amba/
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
add @uptodate argument to end_that_request_last() and @error
to rq_end_io_fn(). there's no generic way to pass error code
to request completion function, making generic error handling
of non-fs request difficult (rq->errors is driver-specific and
each driver uses it differently). this patch adds @uptodate
to end_that_request_last() and @error to rq_end_io_fn().
for fs requests, this doesn't really matter, so just using the
same uptodate argument used in the last call to
end_that_request_first() should suffice. imho, this can also
help the generic command-carrying request jens is working on.
Signed-off-by: tejun heo <htejun@gmail.com>
Signed-Off-By: Jens Axboe <axboe@suse.de>
|
|
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Leave the overloaded "hotplug" word to susbsystems which are handling
real devices. The driver core does not "plug" anything, it just exports
the state to userspace and generates events.
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Since MMCI currently uses PIO to read data, we have to take steps
to ensure data cache coherency on aliasing CPU caches. Add the
necessary flush_dcache_page() calls.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
platform_device_register_simple() is going away, switch to
using platfrom_device_alloc() + platform_device_add(). Also
make sure that wbsd_driver gets unregistered when wbsd_init
fails.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Select a block size for IO based on the read and write block size
combinations, and whether the card supports partial block reads
and/or partial block writes.
If we are able to satisfy block reads but not block writes, mark
the device read only.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
It seems that clk_use() and clk_unuse() are additional complexity
which isn't required anymore. Remove them from the clock framework
to avoid the additional confusion which they cause, and update all
ARM machine types except for OMAP.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
We were passing set_capacity() the capacity we calculated in terms of
the number of blocks on the card, which happened to be the right units
for 512-byte block cards. However, with 1024-byte block cards, we
end up setting the capacity to half the number of blocks. Fix this
by shifting by the appropriate amount.
Thanks to Todd Blumer for pointing this out.
Use get_capacity() to report the card capacity, rather than
recalculating it from the CSD information.
Finally, use our chosen IO block size for the SET_BLOCKLEN command
rather than the CSD read block size. Currently these are equivalent,
but will not be in the future.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
It seems that people get confused about what is happening in
mmc_power_up(). Add a comment to make it clear why we have
a two stage process.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The routine reading the SCR wasn't paying proper attention to the
error codes returned from the driver.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
A review against MMC/SD specifications found some errors in the current
implementation.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
