aboutsummaryrefslogtreecommitdiff
path: root/drivers/mmc
AgeCommit message (Collapse)Author
2008-05-13mmc: make one-bit signed bitfields unsignedHarvey Harrison
Otherwise it can only take the values 0/-1 which doesn't seem to have been intended. drivers/mmc/host/sdhci.h:190:20: error: dubious one-bit signed bitfield Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Acked-by: Pierre Ossman <drzeus-list@drzeus.cx> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-05-04[ARM] 5024/1: Fix some minor clk issues in the MMCI PL18x driverLinus Walleij
This fixes some two minor clk issues. The first is a comparison where a byte will probably wrap around to 0 instead of being saturated to 255, shouldn't be triggered very often but need fixing. The second is an attempt by the driver to adjust MCLK down to the maximum frequency according to the spec, so we don't accidentally overclock the PL18x block. None of the mach-{versatile|integrator|lh7a40x} that use it in-tree seem to have a problem with this (all are well below 100MHz, typically 33MHz), but some day there will be a problem. This is not applied on top of the earlier mmci patch for race condition but rather a clean 2.6.25, but I guess it applies without major protests anyway. Signed-off-by: Linus Walleij <triad@df.lth.se> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-29Merge master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds
* master.kernel.org:/home/rmk/linux-2.6-arm: (26 commits) [ARM] pxa: fix 1c104e0e4f6ab396960c058e95e18bdedcac945b [ARM] serial: s3c2410: platform_get_irq() may return signed unnoticed [ARM] am79c961a: platform_get_irq() may return signed unnoticed [ARM] Feroceon: Feroceon-specific WA-cache compatible {copy,clear}_user_page() [ARM] Feroceon: fix function alignment in proc-feroceon.S [ARM] Orion: catch a couple more alternative spellings of PCIe [ARM] Orion: fix orion-ehci platform resource end addresses [ARM] Orion: fix ->map_irq() PCIe bus number check [ARM] Orion: fix ioremap() optimization [ARM] feroceon: remove CONFIG_CPU_CACHE_ROUND_ROBIN check [ARM] feroceon: remove CONFIG_CPU_DCACHE_WRITETHROUGH check kprobes/arm: fix decoding of arithmetic immediate instructions kprobes/arm: fix cache flush address for instruction stub [ARM] 5022/1: Race in ARM MMCI PL18x driver, V2 [ARM] 5021/1: at91: buildfix for sam9263 + PM [ARM] 5018/1: RealView: Fix the ARM11MPCore Oprofile compilation [ARM] 5016/1: AT91: typo in mci configuration for at91cap at91sam9263 [ARM] 5017/1: pxa3xx: Report unsupported wakeup sources in pxa3xx_set_wake() [ARM] 5020/1: magician: remove __devinit marker from pasic3_leds_info [ARM] 5014/1: Cleanup reset state before entering suspend or resetting. ...
2008-04-29mmc: use get/put_unaligned_* helpersHarvey Harrison
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Tony Jones <tonyj@suse.de> Cc: Pierre Ossman <drzeus@drzeus.cx> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28[ARM] 5022/1: Race in ARM MMCI PL18x driver, V2Linus Walleij
Updated version of 4446/1. This also drops the suggested comparison of host_remain for == 0, since that doesn't make sense (still works for us, too). We have verified that this patch solve race problems on atleast 2 archs at high frequencies. (Verbatim copy of old patch text below.) The patch below fixes a race condition in the ARM MMCI PL18x driver. If new data arrives in the FIFO while existing data is being read then we get a second iteration of the loop in mmci_pio_read. However host->size is not updated until after mmci_pio_read returns, so we get count = number of new bytes PLUS number of bytes already copied in the first iteration. This results in a FIFO underrun as we try and read mode data than is available. The fix is to compensating for data read on previous iterations when calculating the amount of data in the FIFO. Signed-off-by: Linus Walleij <triad@df.lth.se> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-18mmc: sdio_ops.c should #include "sdio_ops.h"Adrian Bunk
Every file should include the headers containing the externs for its global functions. Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18mmc: proper prototypes for mmc_attach_*()Adrian Bunk
This patch adds proper prototypes for mmc_attach_*() in drivers/mmc/core/core.h Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18mmc: make __mmc_release_bus() staticAdrian Bunk
This patch makes the needlessly global __mmc_release_bus() static. Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18sdhci: improve no card, no reset quirkPierre Ossman
The quirk was meant to just inhibit some resets, but ended up blocking all of them. Fortunately, this was just what was needed. Change the comment to reflect reality. Also, this issue has just been observed on Samsung laptops, so reduce the number of chips the quirk affects. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18MMC: OMAP: Do not busy wait for end of command for everJarkko Lavinen
The limit was a fixed 100k limit in the busy loop, which is not accurate. It would better to have time limit for the worst case which occurs when sending 80 cycles at 400 kHz and takes about 200 microseconds, so limit the max time spend in the busy loop for some 250 microseconds. Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18MMC: OMAP: Start new commands from work queue instead of irqJarkko Lavinen
Use work queues for starting new commands instead of starting them directly from irq handler. The command scheduling needs to be delayed a bit for some cards which should not be done from an interrupt. Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18MMC: OMAP: Lazy clock shutdownJarkko Lavinen
MMCA spec says the mmc clock should be kept running for at least 8 cycles after the last RW request. Ensure this with lazy clock disable after a request, or with an explicit delay before switching a slot. Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18MMC: OMAP: Move failing command abortion to workqueueJarkko Lavinen
Abort failed command from workqueue rather than from an interrupt, allowing longer delays in abortion. Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18MMC: OMAP: Use tasklet instead of workqueue for cover switch notificationJarkko Lavinen
The cover waitqueue is occasionally scheduled twice from timer and the interrupt and oops follows. It would have been possible to fix this problem with spinlocks but using tasklet was a dropin solution with no need for locking. This path also adds some cleanups. Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com> Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18MMC: OMAP: Check the get_cover_state function pointer if not setKyungmin Park
If the get_cover_state is not set, it occurs the oops. Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18MMC: OMAP: Using setup_timer instead of init_timerCarlos Eduardo Aguiar
Using setup_timer() instead of init_timer() on omap.c file. Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18MMC: OMAP: Abort stuck commandsJarkko Lavinen
When a card is removed while it is being accessed, a command can get stuck so that no timeout or end of command interrupt ever occurs. The command getting stuck is almost always CDM12, but also the other commands can get stuck. Catch a stuck command with a timer and try sending the initialization stream until the controller starts running again and responds with the end of command status. Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com> Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18MMC: OMAP: General cleanup for MMC multislot supportJuha Yrjola
General code cleanup, modifications at some dev_* functions and other hacks at mmc_omap_irq() for MMC multislot support. Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18MMC: OMAP: Power functions modified to MMC multislot supportJuha Yrjola
Modifications at power functions to MMC multislot support. This patch also move board-specific code out of MMC OMAP driver. Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18MMC: OMAP: Fix timeout calculation for MMC multislot supportJuha Yrjola
Fix the data timeout calculation for MMC multislot support. Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com> Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18MMC: OMAP: New release dma and abort xfer functionsJuha Yrjola
New functions to support MMC multislot: mmc_omap_release_dma() and mmc_omap_abort_xfer(). Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18MMC: OMAP: Add back cover switch supportJuha Yrjola
This patch adds back MMC cover switch support in a way that supports multiple slots. Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com> Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18MMC: OMAP: Introduce new multislot structure and change driver to use itJuha Yrjola
Introduce new MMC multislot structure and change driver to use it. Note that MMC clocking is now enabled in mmc_omap_select_slot() and disabled in mmc_omap_release_slot(). Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com> Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18MMC: OMAP: Remove cover switch handling to allow adding multislot supportTony Lindgren
This patch removes the MMC cover switch handling temporarily to make following multislot patches cleaner. MMC cover switch handling will be added back in later patches after adding basic multislot support. Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18MMC: OMAP: Fix the BYTEBLOCK capability removalFrancisco Alecrim
According with commit 255d01af9a990fd5166f04ed0cc0b30b7b67e81e from Linux-OMAP tree, the BYTEBLOCK capability was removed by Pierre Ossman. MMC_CAP_BYTEBLOCK is not defined causing the compile error: drivers/mmc/host/omap.c: In function `mmc_omap_probe': drivers/mmc/host/omap.c:1077: error: `MMC_CAP_BYTEBLOCK' undeclared (first use in this function) drivers/mmc/host/omap.c:1077: error: (Each undeclared identifier is reported only once drivers/mmc/host/omap.c:1077: error: for each function it appears in.) Signed-off-by: Francisco Alecrim <francisco.alecrim@indt.org.br> Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18MMC: OMAP: Remove extra divisor increaseTony Lindgren
As noted by Kyungmin Park, the divisor calculation has an unnecessary increase. Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18MMC: OMAP: Remove some opcodes from host driverCarlos Eduardo Aguiar
This patch removes some opcodes from host driver so there's no need on putting '#include <linux/mmc/mmc.h>', that should not be needed in host drivers. Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18mmc: use shorter, equivalent set_current_state()Robert P. J. Day
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18sdhci: allow led to be controlled freelyPierre Ossman
Hook up the controller LED to the LED subsystem, allowing more flexible control than simply indicating an ongoing request. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18sdhci: remove custom controller namePierre Ossman
Remove the use of the sdhci specific device name and use the mmc controller name instead. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18mmc: set controller name earlyPierre Ossman
Reorganise code so that mmc_hostname() works directly after allocation. That way host drivers can use that name for resource allocations and messages during probing. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-15mmc: fix platform driver hotplug/coldplugKay Sievers
Since 43cc71eed1250755986da4c0f9898f9a635cb3bf, the platform modalias is prefixed with "platform:". Add MODULE_ALIAS() to the hotpluggable MMC host platform drivers, to re-enable auto loading. Also, add missing owner declarations in driver init. [dbrownell@users.sourceforge.net: registration fixes] Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Pierre Ossman <drzeus@drzeus.cx> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-03-22mmc: use sysfs groups to handle conditional attributesPierre Ossman
Suppressing uevents turned out to be a bad idea as it screws up the order of events, making user space very confused. Change the system to use sysfs groups instead. This is a regression that, for some odd reason, has gone unnoticed for some time. It confuses hal so that the block devices (which have the mmc device as a parent) are not registered. End result being that desktop magic when cards are inserted won't work. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-03-15tifm_sd: DATA_CARRY is not boolean in tifm_sd_transfer_data()Roel Kluin
DATA_CARRY is not boolean Signed-off-by: Roel Kluin <12o3l@tiscali.nl> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-08mmc: extend ricoh_mmc to support Ricoh RL5c476Frank Seidel
This patch adds support for the Ricoh RL5c476 chip: with this the mmc adapter that needs this disabler (R5C843) can also be handled correctly when it sits on a RL5c476. Signed-off-by: Frank Seidel <fseidel@suse.de> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-02-08at91_mci: use generic GPIO callsDavid Brownell
Update the AT91 MMC driver to use the generic GPIO calls instead of the AT91-specific calls; and to request (and release) those GPIO signals. That required updating the probe() fault cleanup codepaths. Now there is a single sequence for freeing resources, in reverse order of their allocation. Also that code uses use dev_*() for messaging, and has less abuse of KERN_ERR. Likewise with updating remove() cleanup. This had to free the GPIOs, and while adding that code I noticed and fixed two other problems: it was poking at a workqueue owned by the mmc core; and in one (rare) case would try freeing an IRQ that it didn't allocate. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-02-08sdhci: add num index for multi controllers caseFeng Tang
Some devices have several controllers; need add the index info to device slot name host->slot_desc[] Signed-off-by: Feng Tang <feng.tang@intel.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-02-08mmc: remove sdhci and mmc_spi experimental markersPierre Ossman
Both of these drivers work well (although some hardware still has its problems) and are not in the "alpha" quality that EXPERIMENTAL suggests. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-02-08mmc: Handle suspend/resume in Ricoh MMC disablerPhilip Langdale
As pci config space is reinitialised on a suspend/resume cycle, the disabler needs to work its magic at resume time. For symmetry this change also explicitly enables the controller at suspend time but it's not strictly necessary. Signed-off-by: Philipl Langdale <philipl@overt.org> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-01-29Merge branch 'blk-end-request' of git://git.kernel.dk/linux-2.6-blockLinus Torvalds
* 'blk-end-request' of git://git.kernel.dk/linux-2.6-block: (30 commits) blk_end_request: changing xsysace (take 4) blk_end_request: changing ub (take 4) blk_end_request: cleanup of request completion (take 4) blk_end_request: cleanup 'uptodate' related code (take 4) blk_end_request: remove/unexport end_that_request_* (take 4) blk_end_request: changing scsi (take 4) blk_end_request: add bidi completion interface (take 4) blk_end_request: changing ide-cd (take 4) blk_end_request: add callback feature (take 4) blk_end_request: changing ide normal caller (take 4) blk_end_request: changing cpqarray (take 4) blk_end_request: changing cciss (take 4) blk_end_request: changing ide-scsi (take 4) blk_end_request: changing s390 (take 4) blk_end_request: changing mmc (take 4) blk_end_request: changing i2o_block (take 4) blk_end_request: changing viocd (take 4) blk_end_request: changing xen-blkfront (take 4) blk_end_request: changing viodasd (take 4) blk_end_request: changing sx8 (take 4) ...
2008-01-28Merge branch 'pxa-plat' into develRussell King
* pxa-plat: (53 commits) [ARM] 4762/1: Basic support for Toradex Colibri module [ARM] pxa: fix mci_init functions returning -1 [ARM] 4737/1: Refactor corgi_lcd to improve readability + bugfix [ARM] 4747/1: pcm027: support for pcm990 baseboard for phyCORE-PXA270 [ARM] 4746/1: pcm027: network support for phyCORE-PXA270 [ARM] 4745/1: pcm027: default configuration [ARM] 4744/1: pcm027: add support for phyCORE-PXA270 CPU module [NET] smc91x: Make smc91x use IRQ resource trigger flags [ARM] pxa: add default config for littleton [ARM] pxa: add basic support for Littleton (PXA3xx Form Factor Platform) [ARM] 4664/1: Add basic support for HTC Magician PDA phones [ARM] 4649/1: Base support for pxa-based Toshiba e-series PDAs. [ARM] pxa: skip registers saving/restoring if entering standby mode [ARM] pxa: fix PXA27x resume [ARM] pxa: Avoid fiddling with CKEN register on suspend [ARM] pxa: Add PXA3 standby code hooked into the IRQ wake scheme [ARM] pxa: Add zylonite MFP wakeup configurations [ARM] pxa: program MFPs for low power mode when suspending [ARM] pxa: make MFP configuration processor independent [ARM] pxa: remove un-used pxa3xx_mfp_set_xxx() functions ... Conflicts: arch/arm/mach-pxa/ssp.c Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-01-28blk_end_request: changing mmc (take 4)Kiyoshi Ueda
This patch converts mmc to use blk_end_request interfaces. Related 'uptodate' arguments are converted to 'error'. Cc: Pierre Ossman <drzeus-mmc@drzeus.cx> Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com> Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-01-27i2c/tps65010: move header to <linux/i2c/...>David Brownell
Move the tps65010 header file from the OMAP arch directory to the more generic <linux/i2c/...> directory, and remove the spurious dependency of this driver on OMAP. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-01-26[ARM] pxa: mmc: add 1st host controller support for pxa3xxBridge Wu
This patchis to add the first mmc controller support for pxa3xx. It's valid for pxa3[0|1|2]0. On zylonite, the first controller supports two slots, this patch only support the first one right now. Signed-off-by: Bridge Wu <bridge.wu@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-01-26[ARM] 4711/1: pxa: mmc: move DMA specific code to platform layerBridge Wu
This patch is to move pxamci DMA specific code to corresponding platform layer because using DRCMRRXMMC/DRCMRTXMMC in pxamci.c makes the driver code dedicated to platform which is not extensible. It is applicable to all pxa platforms. Signed-off-by: Bridge Wu <bridge.wu@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-01-26[ARM] 4709/1: pxa: mmc: add 26MHz support for pxa3[0|1]0 mmc controllerBridge Wu
pxa3[0|1]0 mmc controller can support 26MHz clock mode, they support SD spec 1.1 and MMC spec 4.0 which specify high speed mode. So host caps will include MMC_CAP_MMC_HIGHSPEED and MMC_CAP_SD_HIGHSPEED for pxa3[0|1]0. This patch is to add 26MHz support for them. pxa host clock will be set to 26MHz mode when the card supported max clock rate is higher than or equal to 26MHz. Signed-off-by: Bridge Wu <bridge.wu@marvell.com> Acked-by: Pierre Ossman <drzeus@drzeus.cx> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-12-12sdhci: support JMicron JMB38x chipsPierre Ossman
The JMicron JMB38x chip doesn't support transfers that aren't 32-bit aligned (both size and start address). It also doesn't like switching between PIO and DMA mode, so it needs to be reset after each request. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-12-12sdhci: use PIO when DMA can't satisfy the requestPierre Ossman
Some controllers have been designed on the assumption that all transfers will be 32-bit aligned, both in start address and in size. This is not a guarantee the SDHCI specification provides and not one we can provide. Revert back to PIO for individual requests in order to work around the hardware bug. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-12-12sdhci: don't warn about sdhci 2.0 controllersPierre Ossman
We support 2.0 controllers, even though we don't use anything in the new feature set. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-12-12sdhci: describe quirksPierre Ossman
Add a comment for each quirk to describe what it does and why. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>