aboutsummaryrefslogtreecommitdiff
path: root/drivers/mmc
AgeCommit message (Collapse)Author
2006-07-02[MMC] sdhci: correct register orderPierre Ossman
The sdhci specification states that some registers must be written to in a specific order. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-07-02[MMC] sdhci: proper timeout handlingPierre Ossman
Use the give timeout clock and calculate a proper timeout instead of using the maximum at all times. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-07-02[MMC] sdhci: fix sdhci reset timeoutPierre Ossman
The reset register is automatically cleared when the reset has completed. Hence, we should busy wait and not have a fixed delay. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-07-02[MMC] sdhci: fix timeout loops in sdhciPierre Ossman
The current timeout loop assume that jiffies are updated. This might not be the case depending on locks and if the kernel is compiled without preemption. Change the system to use a counter and fixed delays. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-07-02[MMC] sdhci: support for multiple voltagesPierre Ossman
The sdhci controllers can support up to three voltage levels. Detect which and report back to the MMC layer. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-07-02[MMC] sdhci: print device idPierre Ossman
As sdhci is a generic driver, it is helpful to see some more specific identification of the actual hardware in dmesg. PCI vendor, device and revision is sufficient in most cases. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-07-02[MMC] sdhci: check SDHCI base clockPierre Ossman
A base clock value of 0 means that the driver must get the base clock through some other means. As we have no other way of getting it, we must abort. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-07-01[ARM] 3678/1: MMC: Make OMAP MMC workTony Lindgren
Patch from Tony Lindgren This patch makes OMAP MMC work again: - Fix compile errors - Do not ioremap base as it is already statically mapped - Clean-up platform device handling - Fix compile warnings Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-06-30Remove obsolete #include <linux/config.h>Jörn Engel
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de> Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-06-29Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/devfs-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/devfs-2.6: (22 commits) [PATCH] devfs: Remove it from the feature_removal.txt file [PATCH] devfs: Last little devfs cleanups throughout the kernel tree. [PATCH] devfs: Rename TTY_DRIVER_NO_DEVFS to TTY_DRIVER_DYNAMIC_DEV [PATCH] devfs: Remove the tty_driver devfs_name field as it's no longer needed [PATCH] devfs: Remove the line_driver devfs_name field as it's no longer needed [PATCH] devfs: Remove the videodevice devfs_name field as it's no longer needed [PATCH] devfs: Remove the gendisk devfs_name field as it's no longer needed [PATCH] devfs: Remove the miscdevice devfs_name field as it's no longer needed [PATCH] devfs: Remove the devfs_fs_kernel.h file from the tree [PATCH] devfs: Remove devfs_remove() function from the kernel tree [PATCH] devfs: Remove devfs_mk_cdev() function from the kernel tree [PATCH] devfs: Remove devfs_mk_bdev() function from the kernel tree [PATCH] devfs: Remove devfs_mk_symlink() function from the kernel tree [PATCH] devfs: Remove devfs_mk_dir() function from the kernel tree [PATCH] devfs: Remove devfs_*_tape() functions from the kernel tree [PATCH] devfs: Remove devfs support from the sound subsystem [PATCH] devfs: Remove devfs support from the ide subsystem. [PATCH] devfs: Remove devfs support from the serial subsystem [PATCH] devfs: Remove devfs from the init code [PATCH] devfs: Remove devfs from the partition code ...
2006-06-27[PATCH] 64bit resource: fix up printks for resources in misc driversGreg Kroah-Hartman
This is needed if we wish to change the size of the resource structures. Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com> Cc: Vivek Goyal <vgoyal@in.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-26ARM: OMAP: Fix DMA channel irq handling for omap24xxTony Lindgren
- DMA CSR register is cleared by reading on omap1, but on omap2 it is cleard by writing to it. - DMA TOUT interrupt does not exist on omap24xx, rename it - Add SECURE and MISALIGNED errors by default for omap24xx - Add defines for external DMA request lines Signed-off-by: Tony Lindgren <tony@atomide.com>
2006-06-26[PATCH] devfs: Remove the gendisk devfs_name field as it's no longer neededGreg Kroah-Hartman
And remove the now unneeded number field. Also fixes all drivers that set these fields. Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-26[PATCH] devfs: Remove the devfs_fs_kernel.h file from the treeGreg Kroah-Hartman
Also fixes up all files that #include it. Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-26[PATCH] devfs: Remove devfs_remove() function from the kernel treeGreg Kroah-Hartman
Removes the devfs_remove() function and all callers of it. Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-26[PATCH] devfs: Remove devfs_mk_dir() function from the kernel treeGreg Kroah-Hartman
Removes the devfs_mk_dir() function and all callers of it. Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-19[ARM] 3565/1: AT91RM9200 MMC updateAndrew Victor
Patch from Andrew Victor This patch includes code cleanups and minor fixes to the AT91RM9200 MMC driver. 1. Replace calls to DBG() with pr_debug(). 2. 'host' can never be null, so don't bother checking for that case. 3. Remove SA_SAMPLE_RANDOM from request_irq(). [Patch from Matt Mackall] 4. clk_get() doesn't return NULL on error - need to test returned value with IS_ERR(). 5. Free resources if clk_get() or request_irq() fails. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-06-19[MMC] Convert all hosts except mmci to use data->blkszRussell King
The MMC specification allows non-power of two block sizes. As such, we should not pass the log2 block size to host drivers, but instead pass the byte size. However, ARM MMCI can only work with log2 block size, so continue to pass both the log2 block size and byte block size. This means that for the moment, the byte block size must remain a power of two, but this is the first stage of removing this restriction for other hosts. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-06-12[MMC] sdhci truncated pointer fixAndrew Morton
On 64-bit machines, we just lost the uppermost 32 bits. Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-06-04[MMC] Prevent au1xmmc.c breakage on non-Au1200 AlchemyRalf Baechle
The driver is selectable on other than Au1200 Alchemy systems but won't build nor work - there is no MMC hw. Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-05-24[MMC] Fix premature use of md->diskPierre Ossman
md->disk was being used in a debug message before it was allocated. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-05-19[ARM] 3531/1: i.MX/MX1 SD/MMC ensure, that clock are stopped before new ↵Pavel Pisa
command and cleanups Patch from Pavel Pisa There has been problems that for some paths that clock are not stopped during new command programming and initiation. Result is issuing of incorrect command to the card. Some other problems are cleaned too. Noisy report of known ERRATUM #4 has been suppressed. Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-05-04[MMC] Move set_ios debugging into mmc.cRussell King
Rather than having every driver duplicate the set_ios debugging, provide a single version in mmc.c which can be expanded as we add additional functionality. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-05-04[MMC] Correct mmc_request_done commentsRussell King
mmc_request_done should be called at the end of handling a request, not between the data and initial command parts of the request. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-05-02[MMC] PXA: reduce the number of lines PXAMCI debug usesRussell King
There's no reason for the PXAMCI debug code to print so many lines - it causes the kernel buffer to overflow when trying to debug this driver. Remove some debug messages which are duplicated by core code, and combine other messages, resulting in fewer characters written to the kernel log. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-05-02[MMC] PXA and i.MX: don't avoid sending stop command on errorRussell King
Always send a stop command at the end of a data transfer. If we avoid sending the stop command, some cards remain in data transfer mode, and refuse to accept further read/write commands. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-05-02[MMC] extend data timeout for writesRussell King
The CSD contains a "read2write factor" which determines the multiplier to be applied to the read timeout to obtain the write timeout. We were ignoring this parameter, resulting in the possibility for writes being timed out too early. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-04-30[ARM] 3485/1: i.MX: MX1 SD/MMC fix of unintentional double start possibilityPavel Pisa
Patch from Pavel Pisa The clock starting imxmci_start_clock() function contains hardware issue workaround, which repeats start attempt, if SDHC does not react on the first trial. But the second start attempt can be taken even, if the first succeed and test code misses time limited clock running phase due to delay caused by schedule to other task or some another device interrupt. This change enables to detect such situation. The performance is not issue, because usually at full clock rate only about six loops in delay cycle are needed. Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-04-24[MMC] pxamci: fix data timeout calculationRussell King
The MMC layer gives us two parts for the timeout calculation - a fixed timeout in nanoseconds, and a card clock-speed dependent part. The PXA MMC hardware allows for a timeout based on the fixed host clock speed only. This resulted in some cards being given a short timeout, and therefore failing to work. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-04-02[ARM] 3457/1: i.MX: SD/MMC support for i.MX/MX1Pavel Pisa
Patch from Pavel Pisa This patch adds support of i.MX/MX1 SD/MMC controller. It has been significantly redesigned from the original Sascha Hauer's version to support scatter-gather DMA, to conform to latest Pierre Ossman's and Russell King's MMC-SD Linux 2.6.x infrastructure. The handling of all events has been moved to the softirq context and is designed with no busy-looping in mind. Unfortunately some controller bugs has to be overcome by limited looping about 2-20 usec but these are observed only for initial card recognition phase. There are still some missing/missed IRQs problems under heavy load. Help of somebody with access to the full SDHC design information is probably necessary. Regenerated against 2.6.16-git-060402 to solve clash with other patches. Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-04-02[ARM] 3456/1: AT91RM9200 support for 2.6 (MMC/SD driver)Andrew Victor
Patch from Andrew Victor This patch adds support for the MMC/SD card interface on the Atmel AT91RM9200 processor. Original driver was by Nick Randell, but a number of people have subsequently worked on it. It's currently maintained by Malcolm Noyes. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-03-29[MMC] Pass -DDEBUG on compiler command line if MMC_DEBUG selectedRussell King
Rather than each driver test MMC_DEBUG itself, and define DEBUG, pass it in via the makefile instead. Fix drivers to use pr_debug() where appropriate, and avoid defining a DEBUG() macro. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-03-29[MMC] Add OMAP MMC host driverCarlos Aguiar
Adds OMAP MMC driver. Signed-off-by: Juha Yrjölä <juha.yrjola@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Carlos Aguiar <carlos.aguiar@indt.org.br> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-03-25[PATCH] Remove MODULE_PARMRusty Russell
MODULE_PARM was actually breaking: recent gcc version optimize them out as unused. It's time to replace the last users, which are generally in the most unloved drivers anyway. Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-03-24[PATCH] mmc: Secure Digital Host Controller Interface driverPierre Ossman
Driver for the Secure Digital Host Controller Interface specification. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-03-20[PATCH] handle errors returned by platform_get_irq*()David Vrabel
platform_get_irq*() now returns on -ENXIO when the resource cannot be found. Ensure all users of platform_get_irq*() handle this error appropriately. Signed-off-by: David Vrabel <dvrabel@arcom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-03-04[MMC] au1xmmc: Fix a compilation warning ('status' is not used)Martin Michlmayr
Fix a trivial compilation warning: CC drivers/mmc/au1xmmc.o drivers/mmc/au1xmmc.c: In function ‘au1xmmc_dma_callback’: drivers/mmc/au1xmmc.c:743: warning: unused variable ‘status’ Signed-off-by: Martin Michlmayr <tbm@cyrius.com> Acked-by: Martin Michlmayr <tbm@cyrius.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-03-04[MMC] au1xmmc: Fix linking error because mmc_rsp_type doesn't existMartin Michlmayr
drivers/mmc/au1xmmc.c doesn't compile because commit e92251762d02a46177d4105d1744041e3f8bc465 introduced a typo and passes the wrong argument to the mmc_resp_type macro. Error because of the typo: CC drivers/mmc/au1xmmc.o drivers/mmc/au1xmmc.c: In function ‘au1xmmc_send_command’: drivers/mmc/au1xmmc.c:197: warning: implicit declaration of function ‘mmc_rsp_type’ ... LD .tmp_vmlinux1 drivers/built-in.o: In function `au1xmmc_request':au1xmmc.c:(.text+0x89504): undefined reference to `mmc_rsp_type' :au1xmmc.c:(.text+0x8968c): undefined reference to `mmc_rsp_type' make: *** [.tmp_vmlinux1] Error 1 Error because of the wrong argument: CC drivers/mmc/au1xmmc.o drivers/mmc/au1xmmc.c: In function ‘au1xmmc_send_command’: drivers/mmc/au1xmmc.c:197: error: invalid type argument of ‘->’ Signed-off-by: Martin Michlmayr <tbm@cyrius.com> Acked-by: Jordan Crouse <jordan.crouse@amd.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-03-04[MMC] au1xmmc: Fix compilation error by using platform_driverMartin Michlmayr
drivers/mmc/au1xmmc.c currently doesn't compile; it needs to be converted to use platform_driver. I cannot test this change because of lack of hardware but I followed the drivers this one is based on, and the code is certainly not worse than before. drivers/mmc/au1xmmc.c: At top level: drivers/mmc/au1xmmc.c:1002: error: ‘platform_bus_type’ undeclared here (not in a function) make[2]: *** [drivers/mmc/au1xmmc.o] Error 1 Signed-off-by: Martin Michlmayr <tbm@cyrius.com> Acked-by: Jordan Crouse <jordan.crouse@amd.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-02-16[MMC] mmci: allow small data transfersRussell King
If a data transfer is small (less than a FIFO size) we would hang waiting for the data to be read due to the PIO interrupt not occuring. We allowed for this in our PIO interrupt handler, but not when setting up a data transfer. Apply the "fix" when setting up a data transfer as well. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-02-08[MMC] Remove extra character in AU1XXX MMC Kconfig entryJordan Crouse
An obvious vi fat finger on my part. Signed-off-by: Jordan Crouse <jordan.crouse@amd.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-02-02[MMC] Add MMC command type flagsRussell King
Some hosts need to know the command type, so pass it via a set of flags in cmd->flags. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-01-14Merge master.kernel.org:/home/rmk/linux-2.6-mmcLinus Torvalds
2006-01-13[MMC] mmc_blk_probe() warning fixAndrew Morton
drivers/mmc/mmc_block.c: In function `mmc_blk_probe': drivers/mmc/mmc_block.c:467: warning: long unsigned int format, different type arg (arg 5) We don't know what size sector_t is - cast it. Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-01-13[PATCH] Add mmc_bus_type probe and remove methodsRussell King
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-12[MMC+MFD] Convert mmc to mutexesArjan van de Ven
convert mfd and mmc to mutexes Signed-off-by: Arjan van de Ven <arjan@infradead.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-01-09Merge master.kernel.org:/home/rmk/linux-2.6-mmcLinus Torvalds
2006-01-09[MMC] Add DATA_MULTI flagRussell King
Some hosts need to know that a transfer will be multi-block. Add a data flag to indicate multiple data block transfers. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-01-08[PATCH] Add block_device_operations.getgeo block device methodChristoph Hellwig
HDIO_GETGEO is implemented in most block drivers, and all of them have to duplicate the code to copy the structure to userspace, as well as getting the start sector. This patch moves that to common code [1] and adds a ->getgeo method to fill out the raw kernel hd_geometry structure. For many drivers this means ->ioctl can go away now. [1] the s390 block drivers are odd in this respect. xpram sets ->start to 4 always which seems more than odd, and the dasd driver shifts the start offset around, probably because of it's non-standard sector size. Signed-off-by: Christoph Hellwig <hch@lst.de> Cc: Jens Axboe <axboe@suse.de> Cc: <mike.miller@hp.com> Cc: Jeff Dike <jdike@addtoit.com> Cc: Paolo Giarrusso <blaisorblade@yahoo.it> Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl> Cc: Neil Brown <neilb@cse.unsw.edu.au> Cc: Markus Lidel <Markus.Lidel@shadowconnect.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: James Bottomley <James.Bottomley@steeleye.com> Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-08[MMC] Lindent wbsd driverPierre Ossman
Fix the coding style in the wbsd driver once and for all. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>