aboutsummaryrefslogtreecommitdiff
path: root/drivers/net/Makefile
AgeCommit message (Collapse)Author
2006-12-02[PATCH] Atmel MACB ethernet driverHaavard Skinnemoen
Driver for the Atmel MACB on-chip ethernet module. Tested on AVR32/AT32AP7000/ATSTK1000. I've heard rumours that it works with AT91SAM9260 as well, and it may be possible to share some code with the at91_ether driver for AT91RM9200. Hardware documentation can be found in the AT32AP7000 data sheet, which can be downloaded from http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since previous version: * Probe for PHY ID instead of depending on it being provided through platform_data. * Grab initial ethernet address from the MACB registers instead of depending on platform_data. * Set MII/RMII mode correctly. These changes are mostly about making the driver more compatible with the at91 infrastructure. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-02[PATCH] Add tsi108/9 On Chip Ethernet device driver supportZang Roy-r61911
Add tsi108/9 on chip Ethernet controller driver support. The driver code collects the feedback of previous posting form the mailing list and gives the update. MPC7448HPC2 platform in arch/powerpc uses tsi108 bridge. The following is a brief description of the Ethernet controller: The Tsi108/9 Ethernet Controller connects Switch Fabric to two independent Gigabit Ethernet ports,E0 and E1. It uses a single Management interface to manage the two physical connection devices (PHYs). Each Ethernet port has its own statistics monitor that tracks and reports key interface statistics. Each port supports a 256-entry hash table for address filtering. In addition, each port is bridged to the Switch Fabric through a 2-Kbyte transmit FIFO and a 4-Kbyte Receive FIFO. Each Ethernet port also has a pair of internal Ethernet DMA channels to support the transmit and receive data flows. The Ethernet DMA channels use descriptors set up in memory, the memory map of the device, and access via the Switch Fabric. The Ethernet Controller’s DMA arbiter handles arbitration for the Switch Fabric. The Controller also has a register bus interface for register accesses and status monitor control. The PMD (Physical Media Device) interface operates in MII, GMII, or TBI modes. The MII mode is used for connecting with 10 or 100 Mbit/s PMDs. The GMII and TBI modes are used to connect with Gigabit PMDs. Internal data flows to and from the Ethernet Controller through the Switch Fabric. Each Ethernet port uses its transmit and receive DMA channels to manage data flows through buffer descriptors that are predefined by the system (the descriptors can exist anywhere in the system memory map). These descriptors are data structures that point to buffers filled with data ready to transmit over Ethernet, or they point to empty buffers ready to receive data from Ethernet. Signed-off-by: Alexandre Bounine <Alexandre.Bounine@tundra.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-02Add NetXen 1G/10G ethernet driver.Amit S. Kale
Signed-off-by: Amit S. Kale <amitkale@netxen.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-02[PATCH] 8390 fixes - the final chunk (h8300)Al Viro
The rest of 8390 conversions; ifdef cascade in 8390.h is gone now. Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-02[PATCH] 8390 fixes - m68k oddballsAl Viro
more 8390 conversions - mac8390, zorro8390 and hydra got the same treatment as arm etherh; one more case in 8390.h ifdef cascade is gone. Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-02[PATCH] beginning of 8390 fixes - generic and arm/etherhAl Viro
etherh and a handful of other odd drivers use different macros when building 8390.c. Since we generate a single 8390.o and then link with it, in any config with both oddball and normal 8390-based driver we will end up with breakage in at least one of them. Solution: take most of 8390.c into lib8390.c and have 8390.c, etherh.c and the rest of oddballs #include it. Helper macros are taken from 8390.h to whoever includes lib8390.c. That way odd drivers get separate instances of compiled 8390 stuff and stop stepping on each other's toes. 8390.h gets cleaned up - we don't have the cascade of ifdefs in there and are left with the stuff that can be used by any 8390-based driver. Current problems are exactly because of that cascade - we attempt to choose the set of helpers by looking at config and that, of course, doesn't work well when we have several sets needed by various drivers in our config. Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-09-22[NET] GT96100: Delete bitrotting ethernet driverRalf Baechle
Code for the EV96100 evaluation board hasn't compiled since at least November 15, 2003, so it is being deleted as of 2.6.18 due to lack of a user base. Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-09-13[PATCH] ehea: IBM eHEA Ethernet Device DriverJan-Bernd Themann
Hi Jeff, I fixed the __iomem issue and tested the driver with sparse. Looks good so far. Thanks for your effort. Jan-Bernd Themann Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com> drivers/net/Kconfig | 9 drivers/net/Makefile | 1 drivers/net/ehea/Makefile | 6 drivers/net/ehea/ehea.h | 447 ++++++ drivers/net/ehea/ehea_ethtool.c | 294 ++++ drivers/net/ehea/ehea_hcall.h | 51 drivers/net/ehea/ehea_hw.h | 287 ++++ drivers/net/ehea/ehea_main.c | 2654 ++++++++++++++++++++++++++++++++++++++++ drivers/net/ehea/ehea_phyp.c | 705 ++++++++++ drivers/net/ehea/ehea_phyp.h | 455 ++++++ drivers/net/ehea/ehea_qmr.c | 582 ++++++++ drivers/net/ehea/ehea_qmr.h | 358 +++++ 12 files changed, 5849 insertions(+) Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-08-19Merge branch 'upstream-fixes' into upstreamJeff Garzik
2006-08-19[PATCH] Freescale QE UCC gigabit ethernet driverLi Yang
QE(QUICC Engine) is a new generation communication coprocessor, which can be found on some of the latest Freescale PowerQUICC CPUs(e.g. MPC8360). The UCC(Unified Communications Controller) module of QE can work as gigabit Ethernet device. This patch provides driver for the device. Signed-off-by: Shlomi Gridish <gridish@freescale.com> Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-07-29[PATCH] qla3xxx NIC driverRon Mercer
This is a complementary network driver for our ISP4XXX parts. There is a concurrent effort underway to get the iSCSI driver (qla4xxx) integrated upstream as well. I have been through several iterations with the linux-netdev list and have had much response from Stephen Hemminger. - Built and tested using kernel 2.6.17-rc4. - The chip supports two ethernet and two iSCSI functions. - The functions ql_sem_lock, ql_sem_spinlock, ql_sem_unlock, and ql_wait_for_drvr_lock are used to protect resources that are shared across the network and iSCSI functions. This protection is mostly during chip initialization and resets, but also include link management. - The PHY/MII are not exported through ethtool due to the fact that the iSCSI function will control the common link at least 50% of the time. This driver has been through several iterations on the netdev list and we feel this driver is ready for inclusion in the upstream kernel. It has been built and tested on x86 and PPC64 platforms. Cc: Jeff Garzik <jeff@garzik.org> Cc: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-07-19[PATCH] Cleanup SLHC configurationRalf Baechle
Convert selection of serial line header compression to use CONFIG_SLHC rather than makefile ifeq uglyness. This makes it easier to select the SLHC module from other code. Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-06-22[PATCH] network driver for Hilscher netxSascha Hauer
This is a patch for the Hilscher netx builtin ethernet ports. The netx board support was merged into 2.6.17-git2. The netx is a arm926 based SoC. Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> -- drivers/net/Kconfig | 11 drivers/net/Makefile | 1 drivers/net/netx-eth.c | 516 ++++++++++++++++++++++++++++++++++++++++ include/asm-arm/arch-netx/eth.h | 27 ++ 4 files changed, 555 insertions(+) Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-05-24[PATCH] Add Myri-10G Ethernet driverBrice Goglin
Signed-off-by: Brice Goglin <brice@myri.com> Signed-off-by: Andrew J. Gallatin <gallatin@myri.com> drivers/net/Kconfig | 17 drivers/net/Makefile | 1 drivers/net/myri10ge/Makefile | 5 drivers/net/myri10ge/myri10ge.c | 2851 +++++++++++++++ drivers/net/myri10ge/myri10ge_mcp.h | 205 + drivers/net/myri10ge/myri10ge_mcp_gen_header.h | 58 include/linux/pci_ids.h | 1 7 files changed, 3138 insertions(+) Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-04-20[PATCH] RE: [PATCH 1/1] net driver: Add support for SMSC LAN911x line of ↵Dustin McIntire
ethernet chips > > The patch was badly wordwrapped. Please fix and resend. > OK, I've fixed the wrapping and removed the CONFIG_ARM restriction. I've also did my best to modify the C style to conform to the comments. I noticed that the patch is getting ignored by majordomo due to its size >100K. Should it be broken up somehow to allow posting to the lists? Signed-off-by: Dustin McIntire <dustin@sensoria.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-03-22[PATCH] fix spidernet build issueJens Osterkamp
<unchangelogged> Signed-off-by: Jens Osterkamp <Jens.Osterkamp@de.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-01-09[NET]: Add IFB (Intermediate Functional Block) network device.Jamal Hadi Salim
A new device to do intermidiate functional block in a system shared manner. To use the new functionality, you need to turn on qos/classifier actions. The new functionality can be grouped as: 1) qdiscs/policies that are per device as opposed to system wide. ifb allows for a device which can be redirected to thus providing an impression of sharing. 2) Allows for queueing incoming traffic for shaping instead of dropping. Packets are redirected to this device using tc/action mirred redirect construct. If they are sent to it by plain routing instead then they will merely be dropped and the stats would indicate that. Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-11-18[PATCH] intel ixp2000 network driverLennert Buytenhek
The way the hardware and firmware work is that there is one shared RX queue and IRQ for a number of different network interfaces. Due to this, we would like to process received packets for every interface in the same NAPI poll handler, so we need a pseudo-device to schedule polling on. What the driver currently does is that it always schedules polling for the first network interface in the list, and processes packets for every interface in the poll handler for that first interface -- however, this scheme breaks down if the first network interface happens to not be up, since netif_rx_schedule_prep() checks netif_running(). sky2 apparently has the same issue, and Stephen Hemminger suggested a way to work around this: create a variant of netif_rx_schedule_prep() that does not check netif_running(). I implemented this locally and called it netif_rx_schedule_prep_notup(), and it seems to work well, but it's something that probably not everyone would be happy with. The ixp2000 is an ARM CPU with a high-speed network interface in the CPU itself (full duplex 4Gb/s or 10Gb/s depending on the IXP model.) The CPU package also contains 8 or 16 (again depending on the IXP model) 'microengines', which are somewhat primitive but very fast and efficient processor cores which can be used to offload various things from the main CPU. This driver makes the high-speed network interface in the CPU visible and usable as a regular linux network device. Currently, it only supports the Radisys ENP2611 IXP board, but adding support for other board types should be fairly easy. Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-11-18[PATCH] Gianfar update and sysfs supportAndy Fleming
This seems to have gotten lost, so I'll resend. Signed-off-by: Andy Fleming <afleming@freescale.com> * Added sysfs support to gianfar for modifying FIFO and stashing parameters * Updated driver to support 10 Mbit, full duplex operation * Improved comments throughout * Cleaned up and optimized offloading code * Fixed a bug where rx buffers were being improperly mapped and unmapped * (only manifested if cache-coherency was off) * Added support for using the eTSEC exact-match MAC registers * Bumped the version to 1.3 * Added support for distinguishing between reduced 100 and 10 Mbit modes * Modified default coalescing values to lower latency * Added documentation Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-11-11Merge branch 'master'Jeff Garzik
2005-11-08[PPP]: add PPP MPPE encryption moduleMatt Domsch
From: Matt Domsch <Matt_Domsch@dell.com> The patch below implements the Microsoft Point-to-Point Encryption method as a PPP compressor/decompressor. This is necessary for Linux clients and servers to interoperate with Microsoft Point-to-Point Tunneling Protocol (PPTP) servers (either Microsoft PPTP servers or the poptop project) which use MPPE to encrypt data when creating a VPN. This patch differs from the kernel_ppp_mppe DKMS pacakge at pptpclient.sourceforge.net by utilizing the kernel crypto routines rather than providing its own SHA1 and arcfour implementations. Minor changes to ppp_generic.c try to prevent a link from disabling compression (in our case, the encryption) after it has started using compression (encryption). Feedback to <pptpclient-devel@lists.sourceforge.net> please. Signed-off-by: Matt Domsch <Matt_Domsch@dell.com> Cc: James Cameron <james.cameron@hp.com> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Brice Goglin <Brice.Goglin@ens-lyon.org> Acked-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-11-05Merge branch 'master'Jeff Garzik
2005-10-28Add fs_enet ethernet network driver, for several embedded platforms.Pantelis Antoniou
2005-10-28Merge branch 'master'Jeff Garzik
2005-10-18[PATCH] mipsnet: Virtual ethernet driver for MIPSsim.Ralf Baechle
Signed-off-by: Ralf Baechle <ralf@linux-mips.org> drivers/net/Kconfig | 8 + drivers/net/Makefile | 1 drivers/net/mipsnet.c | 371 ++++++++++++++++++++++++++++++++++++++++++++++++++ drivers/net/mipsnet.h | 127 +++++++++++++++++ 4 files changed, 507 insertions(+) Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-10-03Merge branch 'upstream-fixes'Jeff Garzik
2005-09-27[NET]: Add Sun Cassini driver.David S. Miller
Written by Adrian Sun (asun@darksunrising.com). Ported to 2.6.x by Tom 'spot' Callaway <tcallawa@redhat.com>. Further cleaned up and integrated by David S. Miller Signed-off-by: David S. Miller <davem@davemloft.net>
2005-09-23[netdrvr gianfar] use new phy layerAndy Fleming
Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-09-14[PATCH] Add rapidio net driverMatt Porter
Adds an "Ethernet" driver which sends Ethernet packets over the standard RapidIO messaging. This depends on the core RIO patch for mailbox/doorbell access. Signed-off-by: Matt Porter <mporter@kernel.crashing.org> Cc: Jeff Garzik <jgarzik@pobox.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-09-14Merge /spare/repo/linux-2.6/ Jeff Garzik
2005-09-06[PATCH] net: add driver for the NIC on Cell BladesJens Osterkamp
This patch adds a driver for a new 1000 Mbit ethernet NIC. It is integrated on the south bridge that is used for our Cell Blades. The code gets the MAC address from the Open Firmware device tree, so it won't compile on platforms other than ppc64. This is the first public release, so I don't expect the first version to get merged, but I'd aim for integration within the 2.6.13 time frame. Cc: Utz Bacher <utz.bacher@de.ibm.com> Signed-off-by: Arnd Bergmann <arndb@de.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-08-29/spare/repo/netdev-2.6 branch 'chelsio'Jeff Garzik
2005-08-29Merge /spare/repo/linux-2.6/Jeff Garzik
2005-08-29/spare/repo/netdev-2.6 branch 'sis190'Jeff Garzik
2005-08-17[PATCH] sky2: new experimental Marvell Yukon2 driverStephen Hemminger
New driver for the Marvell Yukon2 Gigabit Ethernet chipset. This driver is based on the skge driver, but using the logic from the SysKonnect version of the sk98lin driver. It should support all the Yukon2 chipsets that are available in many current Intel and AMD motherboards. The driver does support ethtool, tx and rx checksum, and tcp segmentation offload. But it has only been tested for a short while and is known to stop receiving under heavy load. Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-07-30This patch adds a PHY Abstraction Layer to the Linux Kernel, enablingAndy Fleming
ethernet drivers to remain as ignorant as is reasonable of the connected PHY's design and operation details. Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-07-30[PATCH] sis190: resurrectionFrancois Romieu
Raise the sis190 driver from the dead The driver handles the integrated network device found on SiS 965L chipset. It follows the classical (non-napi) interrupt-driven model and provides minimal ethtool support. The code comes from a heavy cleanup/rewrite of the original code which was removed from the kernel on 14/04/2004. Since the r8169 driver does not work too bad and there will probably be (at least) a few months of improvements/testing/fixing, I made the code as close as possible to the r8169 one. Pascal Chapperon <pascal.chapperon@wanadoo.fr> deserves some special credit for testing and bug-catching. Many thanks to Lars Vahlenberg as well. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-06-22Merge /spare/repo/linux-2.6/Jeff Garzik
2005-06-04Automatic merge of /spare/repo/netdev-2.6 branch skge
2005-06-04Automatic merge of /spare/repo/netdev-2.6 branch remove-drivers
2005-06-04Automatic merge of /spare/repo/netdev-2.6 branch dm9000
2005-05-26[BNX2]: New Broadcom gigabit network driver.Michael Chan
A new driver bnx2 for Broadcom bcm5706 is available. The patch also includes new 1000BASE-X advertisement bit definitions in mii.h Thanks to David Miller and Jeff Garzik for reviewing and their valuable feedback. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2005-05-15[PATCH] drivers/net/wireless enabled by wrong optionAl Viro
NET_WIRELESS is only a subset of the stuff in drivers/net/wireless; NET_RADIO is what covers all of them. Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
2005-05-15[PATCH] A new 10GB Ethernet Driver by Chelsio CommunicationsChristoph Lameter
A Linux driver for the Chelsio 10Gb Ethernet Network Controller by Chelsio (http://www.chelsio.com). This driver supports the Chelsio N210 NIC and is backward compatible with the Chelsio N110 model 10Gb NICs. It supports AMD64, EM64T and x86 systems. Signed-off-by: Tina Yang <tinay@chelsio.com> Signed-off-by: Scott Bardone <sbardone@chelsio.com> Signed-off-by: Christoph Lameter <christoph@lameter.com> Adrian said: - my3126.c is unused (because t1_my3126_ops isn't used anywhere) - what are the EXTRA_CFLAGS in drivers/net/chelsio/Makefile for? - $(cxgb-y) in drivers/net/chelsio/Makefile seems to be unneeded - completely unused global functions: - espi.c: t1_espi_get_intr_counts - sge.c: t1_sge_get_intr_counts - the following functions can be made static: - sge.c: t1_espi_workaround - sge.c: t1_sge_tx - subr.c: __t1_tpi_read - subr.c: __t1_tpi_write - subr.c: t1_wait_op_done shemminger said: The performance recommendations in cxgb.txt are common to all fast devices, and should be in one file rather than just for this device. I would rather see ip-sysctl.txt updated or a new file on tuning recommendations started. Some of them have consequences that aren't documented well. For example, turning off TCP timestamps risks data corruption from sequence wrap. A new driver shouldn't need so may #ifdef's unless you want to putit on older vendor versions of 2.4 Some accessor and wrapper functions like: t1_pci_read_config_4 adapter_name t1_malloc are just annoying noise. Why have useless dead code like: /* Interrupt handler */ +static int pm3393_interrupt_handler(struct cmac *cmac) +{ + u32 master_intr_status; +/* + 1. Read master interrupt register. + 2. Read BLOCK's interrupt status registers. + 3. Handle BLOCK interrupts. +*/ Jeff said: step 1: kill all the OS wrappers. And do you really need hooks for multiple MACs, when only one MAC is really supported? Typically these hooks are at a higher level anyway -- struct net_device. From: Christoph Lameter <christoph@lameter Driver modified as suggested by Pekka Enberg, Stephen Hemminger and Andrian Bunk. Reduces the size of the driver to ~260k. - clean up tabs - removed my3126.c - removed 85% of suni1x10gexp_regs.h - removed 80% of regs.h - removed various calls, renamed variables/functions. - removed system specific and other wrappers (usleep, msleep) - removed dead code - dropped redundant casts in osdep.h - dropped redundant check of kfree - dropped weird code (MODVERSIONS stuff) - reduced number of #ifdefs - use kcalloc now instead of kmalloc - Add information about known issues with the driver - Add information about authors Signed-off-by: Scott Bardone <sbardone@chelsio.com> Signed-off-by: Christoph Lameter <christoph@lameter.com> Signed-off-by: Andrew Morton <akpm@osdl.org> diff -puN /dev/null Documentation/networking/cxgb.txt
2005-05-15[PATCH] DM9000 network driverSascha Hauer
This patch adds support for the davicom dm9000 network driver. The dm9000 is found on some embedded arm boards such as the pimx1 or the scb9328. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Andrew Morton <akpm@osdl.org> diff -puN /dev/null drivers/net/dm9000.c
2005-05-12 [PATCH] remove two obsolete net driversAdrian Bunk
The options FMV18X and SK_G16 do depend on the non-available CONFIG_OBSOLETE even in kernel 2.4 - IOW, the last time it was able to select them was in kernel 2.2 (or even before). Since it seems noone misses these drivers, this patch removes them. Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-05-12[netdrvr] new driver skge, for SysKonnect cardsStephen Hemminger
2005-04-16Linux-2.6.12-rc2Linus Torvalds
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!