aboutsummaryrefslogtreecommitdiff
path: root/drivers/net/cxgb3
AgeCommit message (Collapse)Author
2009-02-18cxgb3: Add support for PCI ID 0x35.Divy Le Ray
Add support for adapters with a PCI id equal to 0x35. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-04cxgb3: Fix lro switchDivy Le Ray
The LRO switch is always set to 1 in the rx processing loop. It breaks the accelerated iSCSI receive traffic. Fix its computation. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-19cxgb3: Fix LRO misalignmentDivy Le Ray
The lro manager's frag_align_pad setting was missing, leading to misaligned access to the skb passed up to the stack. Tested-by: Rick Jones <rick.jones2@hp.com> Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-11cxgb3: Keep LRO off if disabled when interface is downRoland Dreier
I have a system with a Chelsio adapter (driven by cxgb3) whose ports are part of a Linux bridge. Recently I updated the kernel and discovered that things stopped working because cxgb3 was doing LRO on packets that were passed into the bridge code for forwarding. (Incidentally, this problem manifested itself in a strange way that made debugging a bit interesting -- for some reason, the skb_warn_if_lro() check in bridge didn't trigger and these LROed packets were forwarded out a forcedeth interface, and caused the forcedeth transmit path to get stuck) This is because cxgb3 has no way of keeping state for the LRO flag until the interface is brought up, so if the bridging code disables LRO while the interface is down, then cxgb3_up() will just reenable LRO, and on my Debian system at least, the init scripts add interfaces to a bridge before bringing the interfaces up. Fix this by keeping track of each interface's LRO state in cxgb3 so that when bridge disables LRO, it stays disabled in cxgb3_up() when the interface is brought up. I did this by changing the rx_csum_offload flag into a pair of bit flags; the effect of this on the rx_eth() fast path is miniscule enough that it should be fine (eg on x86, a cmpb instruction becomes a testb instruction). Signed-off-by: Roland Dreier <rolandd@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26cxgb3: add control to access embedded imagesDivy Le Ray
Update contol path between cxgb3 and ULP modules (iWARP, iSCSI) to provide access to firware and protocol engine info. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-25drivers/net/cxgb3: comment out dead codeHannes Eder
The function 'vsc8211_set_speed_duplex' is not used, so comment it out. For 'vsc8211_set_automdi' the function 'vsc8211_set_speed_duplex' is the only caller, so comment it out as well. Fix this (sparse) warning: drivers/net/cxgb3/vsc8211.c:269: warning: 'vsc8211_set_automdi' defined but not used drivers/net/cxgb3/vsc8211.c:295:5: warning: symbol 'vsc8211_set_speed_duplex' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-18cxgb3: manage private iSCSI IP addressKaren Xie
The accelerated iSCSI traffic could use a private IP address unknown to the OS: - The IP address is required in both drivers to manage ARP requests and connection set up. - Added an control call to retrieve the ip address. - Reply to ARP requests dedicated to the private IP address. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: Karen Xie <kxie@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-16cxgb3: untie strict FW matchingDivy Le Ray
The NIC driver can work with mutliple versions of the FW. Let the driver load when the embedded FW does not match, and the FW update mechanism failed. The iWARP module will make its own loading decision. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-16cxgb3: Add multiple Tx queue support.Divy Le Ray
Implement NIC Tx multiqueue. Bump up driver version. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-28cxgb3: Fix sparse warning and micro-optimize is_pure_response()Roland Dreier
The function is_pure_response() does "ntohl(var) & const" and then essentially just tests whether the result is 0 or not; this can be done more efficiently by computing "var & htonl(const)" instead and doing the byte swap at compile time instead of run time. This change slightly shrinks the compiled code; eg on x86-64 we save a couple of bswapl instructions: add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-8 (-8) function old new delta t3_sge_intr_msix_napi 544 536 -8 and this also has the pleasant side effect of fixing a sparse warning: drivers/net/cxgb3/sge.c:2313:15: warning: restricted degrades to integer Signed-off-by: Roland Dreier <rolandd@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-26cxgb3: Update FW loading path.Divy Le Ray
Update FW loading path to accomodate in-kernel images location Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-26cxgb3: avoid potential memory leak.Divy Le Ray
Add consistency in alloc_ring() parameter checking to avoid potential memory leaks. alloc_ring() callers are correct fo far. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-26cxgb3: set hard_xmit in the netdev_opsDivy Le Ray
Fix t3_eth_xmit() missing into the netdev_ops structure. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20netdev: add more functions to netdevice opsStephen Hemminger
This patch moves neigh_setup and hard_start_xmit into the network device ops structure. For bisection, fix all the previously converted drivers as well. Bonding driver took the biggest hit on this. Added a prefetch of the hard_start_xmit in the fast path to try and reduce any impact this would have. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-19cxgb3: convert to net_device_opsStephen Hemminger
Convert this driver to network device ops. Compile tested only. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-18Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/isdn/i4l/isdn_net.c fs/cifs/connect.c
2008-11-11RDMA/cxgb3: deadlock in iw_cxgb3 can cause hang when configuring interface.Steve Wise
When the iw_cxgb3 module's cxgb3_client "add" func gets called by the cxgb3 module, the iwarp driver ends up calling the ethtool ops get_drvinfo function in cxgb3 to get the fw version and other info. Currently the iwarp driver grabs the rtnl lock around this down call to serialize. As of 2.6.27 or so, things changed such that the rtnl lock is held around the call to the netdev driver open function. Also the cxgb3_client "add" function doesn't get called if the device is down. So, if you load cxgb3, then load iw_cxgb3, then ifconfig up the device, the iw_cxgb3 add func gets called with the rtnl_lock held. If you load cxgb3, ifconfig up the device, then load iw_cxgb3, the add func gets called without the rtnl_lock held. The former causes the deadlock, the latter does not. In addition, there are iw_cxgb3 sysfs handlers that also can call down into cxgb3 to gather the fw and hw versions. These can be called concurrently on different processors and at any time. Thus we need to push this serialization down in the cxgb3 driver get_drvinfo func. The fix is to remove rtnl lock usage, and use a per-device lock in cxgb3. Signed-off-by: Steve Wise <swise@opengridcomputing.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-11cxgb3 - Limit multiqueue setting to msi-xDivy Le Ray
Allow multiqueue setting in MSI-X mode only Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-11cxgb3 - eeprom read fixesDivy Le Ray
Protect against invalid phy entries in the eeprom. Extend eeprom access timeout. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-03drivers/net: Kill now superfluous ->last_rx stores.David S. Miller
The generic packet receive code takes care of setting netdev->last_rx when necessary, for the sake of the bonding ARP monitor. Drivers need not do it any more. Some cases had to be skipped over because the drivers were making use of the ->last_rx value themselves. Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-31cxgb3 - enable lro control through ethtoolDivy Le Ray
Implement ethtool's get_flags and set_flags methods. It enables ethtool to control the LRO settings. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-22cxgb3: Fix kernel crash caused by uninitialized l2t_entry.arpqRoland Dreier
Commit 147e70e6 ("cxgb3: Use SKB list interfaces instead of home-grown implementation.") causes a crash in t3_l2t_send_slow() when an iWARP connection request is received. This is because the new l2t_entry.arpq skb queue is never initialized, and therefore trying to add an skb to it causes a NULL dereference. With the old code there was no need to initialize the queues because the l2t_entry structures were zeroed, and the code used NULL to mean empty. Fix this by adding __skb_queue_head_init() when all the l2t_entry structures get allocated. Signed-off-by: Roland Dreier <rolandd@cisco.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-13cxgb3: extend copyrights to 2008Divy Le Ray
Update copyright banner to 2008. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-13cxgb3: update driver versionDivy Le Ray
Add a field to the driver versioning info. Update version to 1.1.0. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08cxgb3: Add 1G fiber supportDivy Le Ray
Add support for 1G optical Vitesse PHY. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08cxgb3: Support for Aeluros 2005 PHYDivy Le Ray
Add support for SR PHY. Auto-detect phy module type, and report type changes. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08cxgb3: commnonize LASI phy codeDivy Le Ray
Add generic code to manage interrupt driven PHYs. Do not reset the phy after link parameters update, the new values might get lost. Return early from link change notification when the link parameters remain unchanged. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08cxgb3: More flexible support for PHY interrupts.Divy Le Ray
Do not require PHY interrupts to be connected to GPIs in ascending order. Base interrupt availability both on PHYs supporting them and on GPIs being hooked up. Allows boards to specify interrupt GPIs though the PHYs don't use them. Remove spurious PHY interrupts due to clearing T3DBG interrupts before setting their polarity. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08cxgb3: simplify port type struct and usageDivy Le Ray
Second step in overall phy layer reorganization. Clean up the port_type_info structure. Support coextistence of clause 22 and clause 45 MDIO devices. Select the type of MDIO transaction on a per transaction basis. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08cxgb3: allow for PHY reset statusDivy Le Ray
First step towards overall PHY layering re-organization. Allow a status return when a PHY is reset. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08cxgb3: Allocate multiqueues at init timeDivy Le Ray
Allocate a queue set per core, up to the maximum of available qsets. Share the queue sets on multi port adapters. Rename MSI-X interrupt vectors ethX-N, N being the queue set number. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08cxgb3: reset the adapter on fatal errorDivy Le Ray
when a fatal error occurs, bring ports down, reset the chip, and bring ports back up. Factorize code used for both EEH and fatal error recovery. Fix timer usage when bringing up/resetting sge queue sets. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08[2.6.28,1/1] cxgb3 - fix race in EEHDivy Le Ray
A SGE queue set timer might access registers while in EEH recovery, triggering an EEH error loop. Stop all timers early in EEH process. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-09-24drivers/net: replace __FUNCTION__ with __func__Harvey Harrison
__FUNCTION__ is gcc-specific, use __func__ Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-24cxgb3 - remove duplicate tests in lroDivy Le Ray
The generic lro code checks TCP flags/options. Remove duplicate tests done in the driver. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-22cxgb3: Use SKB list interfaces instead of home-grown implementation.David S. Miller
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-29cxgb3: Allow 64KB firmware images.Steve Wise
Starting with FW version 7.0, the driver needs to allow larger images. Signed-off-by: Steve Wise <swise@opengridcomputing.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-26dma-mapping: add the device argument to dma_mapping_error()FUJITA Tomonori
Add per-device dma_mapping_ops support for CONFIG_X86_64 as POWER architecture does: This enables us to cleanly fix the Calgary IOMMU issue that some devices are not behind the IOMMU (http://lkml.org/lkml/2008/5/8/423). I think that per-device dma_mapping_ops support would be also helpful for KVM people to support PCI passthrough but Andi thinks that this makes it difficult to support the PCI passthrough (see the above thread). So I CC'ed this to KVM camp. Comments are appreciated. A pointer to dma_mapping_ops to struct dev_archdata is added. If the pointer is non NULL, DMA operations in asm/dma-mapping.h use it. If it's NULL, the system-wide dma_ops pointer is used as before. If it's useful for KVM people, I plan to implement a mechanism to register a hook called when a new pci (or dma capable) device is created (it works with hot plugging). It enables IOMMUs to set up an appropriate dma_mapping_ops per device. The major obstacle is that dma_mapping_error doesn't take a pointer to the device unlike other DMA operations. So x86 can't have dma_mapping_ops per device. Note all the POWER IOMMUs use the same dma_mapping_error function so this is not a problem for POWER but x86 IOMMUs use different dma_mapping_error functions. The first patch adds the device argument to dma_mapping_error. The patch is trivial but large since it touches lots of drivers and dma-mapping.h in all the architecture. This patch: dma_mapping_error() doesn't take a pointer to the device unlike other DMA operations. So we can't have dma_mapping_ops per device. Note that POWER already has dma_mapping_ops per device but all the POWER IOMMUs use the same dma_mapping_error function. x86 IOMMUs use device argument. [akpm@linux-foundation.org: fix sge] [akpm@linux-foundation.org: fix svc_rdma] [akpm@linux-foundation.org: build fix] [akpm@linux-foundation.org: fix bnx2x] [akpm@linux-foundation.org: fix s2io] [akpm@linux-foundation.org: fix pasemi_mac] [akpm@linux-foundation.org: fix sdhci] [akpm@linux-foundation.org: build fix] [akpm@linux-foundation.org: fix sparc] [akpm@linux-foundation.org: fix ibmvscsi] Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Cc: Muli Ben-Yehuda <muli@il.ibm.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Avi Kivity <avi@qumranet.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-18Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/torvalds/linux-2.6 Conflicts: Documentation/powerpc/booting-without-of.txt drivers/atm/Makefile drivers/net/fs_enet/fs_enet-main.c drivers/pci/pci-acpi.c net/8021q/vlan.c net/iucv/iucv.c
2008-07-14RDMA/cxgb3: Fixes for zero STagSteve Wise
Handling the zero STag in receive work request requires some extra logic in the driver: - Only set the QP_PRIV bit for kernel mode QPs. - Add a zero STag build function for recv wrs. The uP needs a PBL allocated and passed down in the recv WR so it can construct a HW PBL for the zero STag S/G entries. Note: we need to place a few restrictions on zero STag usage because of this: 1) all SGEs in a recv WR must either be zero STag or not. No mixing. 2) an individual SGE length cannot exceed 128MB for a zero-stag SGE. This should be OK since it's not really practical to allocate such a large chunk of pinned contiguous DMA mapped memory. - Add an optimized non-zero-STag recv wr format for kernel users. This is needed to optimize both zero and non-zero STag cracking in the recv path for kernel users. - Remove the iwch_ prefix from the static build functions. - Bump required FW version. Signed-off-by: Steve Wise <swise@opengridcomputing.com>
2008-07-14RDMA/cxgb3: Add support for protocol statisticsSteve Wise
- Add a new rdma ctl command called RDMA_GET_MIB to the cxgb3 low level driver to obtain the protocol mib from the rnic hardware. - Add new iw_cxgb3 provider method to get the MIB from the low level driver. Signed-off-by: Steve Wise <swise@opengridcomputing.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-07-11cxgb3 - Add iscsi supportKaren Xie
Add iSCSI (S3xx) support. Signed-off-by: Karen Xie <kxie@chelsio.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-10cxgb3: treat firmware data as constDavid Woodhouse
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2008-07-08vlan: move struct vlan_dev_info to private headerPatrick McHardy
Hide struct vlan_dev_info from drivers to prevent them from growing more creative ways to use it. Provide accessors for the two drivers that currently use it. Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24cxgb3 - add missing adapter type for RDMADivy Le Ray
T3C added support is now reflected to the RDMA driver. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-22cxgb3 - Add LRO supportDivy Le Ray
Add LRO support. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-22cxgb3 - Add page support to jumbo frame Rx queueDivy Le Ray
Add page support to Jumbo frame Rx queues. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-22cxgb3 - Fix dma mapping error pathDivy Le Ray
Take potential dma mapping errors in account. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-13cxgb3 - fix EEHDivy Le Ray
Reset the chip when the PCI link goes down. Preserve the napi structure when a sge qset's resources are freed. Replay only HW initialization when the chip comes out of reset. Signed-off-by: Divy Le ray <divy@chelsio.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-13cxgb3 - fix port up/down error pathDivy Le Ray
Fix faiures path when ports are stopped and restarted in EEH recovery. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>