| Age | Commit message (Collapse) | Author |
|---|
|
master.kernel.org:/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:
Documentation/powerpc/booting-without-of.txt
drivers/atm/Makefile
drivers/net/fs_enet/fs_enet-main.c
drivers/pci/pci-acpi.c
net/8021q/vlan.c
net/iucv/iucv.c
|
|
Handling the zero STag in receive work request requires some extra
logic in the driver:
- Only set the QP_PRIV bit for kernel mode QPs.
- Add a zero STag build function for recv wrs. The uP needs a PBL
allocated and passed down in the recv WR so it can construct a HW
PBL for the zero STag S/G entries. Note: we need to place a few
restrictions on zero STag usage because of this:
1) all SGEs in a recv WR must either be zero STag or not. No mixing.
2) an individual SGE length cannot exceed 128MB for a zero-stag SGE.
This should be OK since it's not really practical to allocate
such a large chunk of pinned contiguous DMA mapped memory.
- Add an optimized non-zero-STag recv wr format for kernel users.
This is needed to optimize both zero and non-zero STag cracking in
the recv path for kernel users.
- Remove the iwch_ prefix from the static build functions.
- Bump required FW version.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
|
|
- Add a new rdma ctl command called RDMA_GET_MIB to the cxgb3 low
level driver to obtain the protocol mib from the rnic hardware.
- Add new iw_cxgb3 provider method to get the MIB from the low level
driver.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Add iSCSI (S3xx) support.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Hide struct vlan_dev_info from drivers to prevent them from growing
more creative ways to use it. Provide accessors for the two drivers
that currently use it.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
T3C added support is now reflected to the RDMA driver.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Add LRO support.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Add page support to Jumbo frame Rx queues.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Take potential dma mapping errors in account.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Reset the chip when the PCI link goes down.
Preserve the napi structure when a sge qset's resources are freed.
Replay only HW initialization when the chip comes out of reset.
Signed-off-by: Divy Le ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Fix faiures path when ports are stopped and restarted
in EEH recovery.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Otherwise theoretically at least
CAP_NET_ADMIN
Reload new firmware
Wait..
Firmware patches kernel
So it should be CAY_SYS_RAWIO - not that I suspect this is in fact a
credible attack vector!
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Open MPI, Intel MPI and other applications don't respect the iWARP
requirement that the client (active) side of the connection send the
first RDMA message. This class of application connection setup is
called peer-to-peer. Typically once the connection is setup, _both_
sides want to send data.
This patch enables supporting peer-to-peer over the chelsio RNIC by
enforcing this iWARP requirement in the driver itself as part of RDMA
connection setup.
Connection setup is extended, when the peer2peer module option is 1,
such that the MPA initiator will send a 0B Read (the RTR) just after
connection setup. The MPA responder will suspend SQ processing until
the RTR message is received and reply-to.
In the longer term, this will be handled in a standardized way by
enhancing the MPA negotiation so peers can indicate whether they
want/need the RTR and what type of RTR (0B read, 0B write, or 0B send)
should be sent. This will be done by standardizing a few bits of the
private data in order to negotiate all this. However this patch
enables peer-to-peer applications now and allows most of the required
firmware and driver changes to be done and tested now.
Design:
- Add a module option, peer2peer, to enable this mode.
- New firmware support for peer-to-peer mode:
- a new bit in the rdma_init WR to tell it to do peer-2-peer
and what form of RTR message to send or expect.
- process _all_ preposted recvs before moving the connection
into rdma mode.
- passive side: defer completing the rdma_init WR until all
pre-posted recvs are processed. Suspend SQ processing until
the RTR is received.
- active side: expect and process the 0B read WR on offload TX
queue. Defer completing the rdma_init WR until all
pre-posted recvs are processed. Suspend SQ processing until
the 0B read WR is processed from the offload TX queue.
- If peer2peer is set, driver posts 0B read request on offload TX
queue just after posting the rdma_init WR to the offload TX queue.
- Add CQ poll logic to ignore unsolicitied read responses.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
None of these files use any of the functionality promised by
asm/semaphore.h. It's possible that they rely on it dragging in some
unrelated header file, but I can't build all these files, so we'll have
fix any build failures as they come up.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
|
|
Fix the warning:
drivers/net/cxgb3/cxgb3_main.c: In function ‘offload_open’:
drivers/net/cxgb3/cxgb3_main.c:936: warning: ignoring return value of
‘sysfs_create_group’, declared with attribute warn_unused_result
Now the return value is checked; if sysfs_create_group() returns failure,
a warning is printed using dev_dbg, and the code continues as before. Use
of dev_dbg ensures printk is not needlessly included unless desired for
debugging.
Signed-off-by: Dan Noe <dpn@isomerica.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/usb/rndis_host.c
drivers/net/wireless/b43/dma.c
net/ipv6/ndisc.c
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Using iWARP with a Chelsio T3 NIC generates the following lockdep warning:
=================================
[ INFO: inconsistent lock state ]
2.6.25-rc6 #50
---------------------------------
inconsistent {softirq-on-W} -> {in-softirq-W} usage.
swapper/0 [HC0[0]:SC1[1]:HE0:SE0] takes:
(&adap->sge.reg_lock){-+..}, at: [<ffffffff880e5ee2>] cxgb_offload_ctl+0x3af/0x507 [cxgb3]
The problem is that reg_lock is used with plain spin_lock() in
drivers/net/cxgb3/sge.c but is used with spin_lock_irqsave() in
drivers/net/cxgb3/cxgb3_offload.c. This is technically a false
positive, since the uses in sge.c are only in the initialization and
cleanup paths and cannot overlap with any use in interrupt context.
The best fix is probably just to use spin_lock_irq() with reg_lock in
sge.c. Even though it's not strictly required for correctness, it
avoids triggering lockdep and the extra overhead of disabling
interrupts is not important at all in the initialization and cleanup
slow paths.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/wireless/rt2x00/rt2x00dev.c
net/8021q/vlan_dev.c
|
|
The last change in the Tx queue stop mechanism opens a window
where the Tx queue might be stopped after pending credits
returned.
Tx credits are returned via a control message generated by the HW.
It returns tx credits on demand, triggered by a completion bit
set in selective transmit packet headers.
The current code can lead to the Tx queue stopped
with all pending credits returned, and the current frame
not triggering a credit return. The Tx queue will then never be
awaken.
The driver could alternatively request a completion for packets
that stop the queue. It's however safer at this point to go back
to the pre-existing behaviour.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
neigh_is_connected() is not popular at all, and the only user
drivers/net/cxgb3/l2t.c:t3_l2t_update() also have raw (expanded) expression.
Let's expand it and remove the inline function.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
|
|
When ARP completes due to a request rather than a reply the neighbor is
marked NUD_STALE instead of reachable (see arp_process()). The handler
for the resulting netevent needs to check also for NUD_STALE.
Failure to use the arp entry can cause RDMA connection failures.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
1. Add common code for stopping queue.
2. No need to call netif_stop_queue followed by netif_wake_queue (and
infact a netif_start_queue could have been used instead), instead
call stop_queue if required, and remove code under USE_GTS macro.
3. There is no need to check for netif_queue_stopped, as the network
core guarantees that for us (I am sure every driver could remove
that check, eg e1000 - I have tested that path a few billion times
with about a few hundred thousand qstops but the condition never
hit even once).
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Checking if an address is a vmalloc address is done in a couple of places.
Define a common version in mm.h and replace the other checks.
Again the include structures suck. The definition of VMALLOC_START and
VMALLOC_END is not available in vmalloc.h since highmem.c cannot be included
there.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When PCI error recovery was added to cxgb3, a function t3_io_slot_reset()
was added. This function can call back into t3_prep_adapter() at any
time, so t3_prep_adapter() can no longer be marked __devinit.
This patch removes the __devinit annotation from t3_prep_adapter() and
all the functions that it calls, which fixes
WARNING: drivers/net/cxgb3/built-in.o(.text+0x2427): Section mismatch in reference from the function t3_io_slot_reset() to the function .devinit.text:t3_prep_adapter()
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
set_pci_drvdata() stores a pointer to the adapter,
not the net device.
Add missing softirq blocking in t3_mgmt_tx.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Add parity initialization for T3C adapters.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Synchronize memory access before ringing
the Tx door bell.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Disable PEX errors. The HW generates false positives.
Update RSS hash function to a symmetric algorithm.
Update T3C HW support
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Remove unused argument in sysfs methods
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Do not use skb->cb to stash unmap info,
save the info to the descriptor state.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Bump up FW version to 5.0.
Do not downgrade FW within the same major version range.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Add PCI recovery support
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Remove sysfs entries before unregistering the net devices.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Subdevice ID is not necessarily set to 1.
Use wild card for PCI device matching
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Return error code when msi-x settings fail.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Update GPIO mapping for T3C.
Update xgmac for T3C support.
Fix typo in mtu table.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Rather than hand-rolling our own prototype, make the code more
future-proof by using the standard irq_handler_t typedef.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
remove asm/bitops.h includes
including asm/bitops directly may cause compile errors. don't include it
and include linux/bitops instead. next patch will deny including asm header
directly.
Cc: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix warnings from sparse related to shadowed variables and routines
that should be declared static.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This patch removes dead code ("tx_xcnt" can never be != 0 at this place)
spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
These have been superceded by the new ->get_sset_count() hook.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For the operations
get-tx-csum
get-sg
get-tso
get-ufo
the default ethtool_op_xxx behavior is fine for all drivers, so we
permit op==NULL to imply the default behavior.
This provides a more uniform behavior across all drivers, eliminating
ethtool(8) "ioctl not supported" errors on older drivers that had
not been updated for the latest sub-ioctls.
The ethtool_op_xxx() functions are left exported, in case anyone
wishes to call them directly from a driver-private implementation --
a not-uncommon case. Should an ethtool_op_xxx() helper remain unused
for a while, except by net/core/ethtool.c, we can un-export it at a
later date.
[ Resolved conflicts with set/get value ethtool patch... -DaveM ]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it. The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.
[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
