| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reworked receive queue fill policies to make the driver more tolerant
in low memory conditions.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PAGE_SIZE allocations via slab are not guaranteed to be page-aligned. Fixed
all memory allocations where page alignment is required by firmware.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adapt to lately introduced net_device_ops structure.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Following the removal of the unused struct net_device * parameter from
the NAPI functions named *netif_rx_* in commit 908a7a1, they are
exactly equivalent to the corresponding *napi_* functions and are
therefore redundant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These are powerpc specific drivers.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
ehea_plpar_hcall9() takes an "unsigned long" array to return its results,
so change the arrays we pass to it to match. This is currently only
64 bit code, so the transformation is actually a noop, but because
ehea_plpar_hcall9() copies the values of registers into the array,
if this was ported to a 32 bit hypervisor interface "unsigned long"
would probably still be the correct type.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The flags field of struct ehea_port is only used with test_bit(),
clear_bit() and set_bit() and these interfaces only work on
"unsigned long"s, so change the field to be an "unsigned long". Also,
this field only has two bits defined for it (0 and 1) so will still be
fine if someone builds this driver for a 32 bit arch (at least as far as
this flags field is concerned).
Also note that ehea_driver_flags is only used in ehca_main.c, so make it
static in there.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 908a7a16b852ffd618a9127be8d62432182d81b4 ("net: Remove unused
netdev arg from some NAPI interfaces") missed two spots.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
With slub debug enabled, I see the following errors and crash with
2.6.28-rc9:
IBM eHEA ethernet device driver (Release EHEA_0095)
ehea: Error in ehea_h_register_rpage_mr: not on pageboundary
ehea: Error in ehea_reg_mr_section: register_rpage_mr failed
ehea: Error in ehea_reg_kernel_mr: registering mr failed
ehea: Error in ehea_setup_ports: creating MR failed
ehea 23c00100.lhea: setup_ports failed
Unable to handle kernel paging request for data at address 0x6b6b6b6b6b6bbdcb
Faulting instruction address: 0xd000000000064a24
cpu 0x0: Vector: 300 (Data Access) at [c0000000740e7190]
pc: d000000000064a24: .ehea_update_firmware_handles+0x84/0x47c [ehea]
lr: d00000000006df34: .ehea_probe_adapter+0x35c/0x39c [ehea]
sp: c0000000740e7410
msr: 8000000000009032
dar: 6b6b6b6b6b6bbdcb
dsisr: 40000000
current = 0xc000000074233780
paca = 0xc0000000008a3300
pid = 2046, comm = modprobe
enter ? for help
[c0000000740e74f0] d00000000006df34 .ehea_probe_adapter+0x35c/0x39c [ehea]
[c0000000740e75a0] c00000000041d5a4 .of_platform_device_probe+0x78/0xb0
[c0000000740e7630] c0000000002d8b38 .driver_probe_device+0x13c/0x200
[c0000000740e76c0] c0000000002d8c90 .__driver_attach+0x94/0xd8
[c0000000740e7750] c0000000002d7d64 .bus_for_each_dev+0x80/0xd8
[c0000000740e7800] c0000000002d889c .driver_attach+0x28/0x40
[c0000000740e7880] c0000000002d8340 .bus_add_driver+0xd4/0x284
[c0000000740e7920] c0000000002d90a0 .driver_register+0xc4/0x198
[c0000000740e79d0] c00000000041d45c .of_register_driver+0x4c/0x60
[c0000000740e7a50] c000000000020ef8 .ibmebus_register_driver+0x30/0x4c
[c0000000740e7ae0] d00000000006e108 .ehea_module_init+0x194/0x208c [ehea]
[c0000000740e7b90] c000000000009028 .do_one_initcall+0x90/0x1ac
[c0000000740e7d90] c00000000008619c .sys_init_module+0xc4/0x200
[c0000000740e7e30] c0000000000084ac syscall_exit+0x0/0x40
(When slub debug is disabled it works fine.)
PAGE_SIZE allocations via slab are not guaranteed to be page-aligned;
use get_zeroed_page for the 'pt' buffer (I don't really know what this
is, only that it is passed to firmware and that the first error
message complains about its alignment). This allows the system to
boot.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In each case, vpage is checked not to be NULL just after it is initialized
at the beginning of each loop iteration.
A simplified version of the semantic patch that makes this change is as
follows: (http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
expression E;
position p1,p2;
@@
if (x@p1 == NULL || ...) { ... when forall
return ...; }
... when != \(x=E\|x--\|x++\|--x\|++x\|x-=E\|x+=E\|x|=E\|x&=E\|&x\)
(
x@p2 == NULL
|
x@p2 != NULL
)
// another path to the test that is not through p1?
@s exists@
local idexpression r.x;
position r.p1,r.p2;
@@
... when != x@p1
(
x@p2 == NULL
|
x@p2 != NULL
)
@fix depends on !s@
position r.p1,r.p2;
expression x,E;
statement S1,S2;
@@
(
- if ((x@p2 != NULL) || ...)
S1
|
- if ((x@p2 == NULL) && ...) S1
|
- BUG_ON(x@p2 == NULL);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the napi api was changed to separate its 1:1 binding to the net_device
struct, the netif_rx_[prep|schedule|complete] api failed to remove the now
vestigual net_device structure parameter. This patch cleans up that api by
properly removing it..
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes some trailing whitespaces and spaces before tabs.
Signed-off-by: Hannes Hering <hering2@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Drivers need not do it any more.
Some cases had to be skipped over because the drivers
were making use of the ->last_rx value themselves.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All kernel memory which is used for kernel/hardware data transfer must
be registered with firmware using "memory regions". 16GB hugepages
may not be part of a memory region due to firmware restrictions.
This patch modifies the walk_memory_resource callback fn to filter
hugepages and add only standard memory to the busmap which is later
on used for MR registration.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
This patch implements the memory notifier to update the busmap
instantly instead of rebuilding the whole map. This is necessary
because walk_memory_resource provides different information than
required during memory hotplug.
Signed-off-by: Hannes Hering <hering2@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
This reverts commit 2eefbd63d0c85daa1317636474c226e236beba81.
On request by driver author and Jeff Garzik.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the capability flag to the capability list for dynamic LPAR
memory remove to enable this feature.
Signed-off-by: Hannes Hering <hering2@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Looks like to me that the ehea_fw_handles.lock mutex and the
ehea_bcmc_regs.lock spinlock are taken much longer than necessary and could
as well be pushed inside the functions that need them
(ehea_update_firmware_handles() and ehea_update_bcmc_registrations())
rather than at each callsite.
Signed-off-by: Sebastien Dugue <sebastien.dugue@bull.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The ehea busmap must be allocated only once in the first of many calls of the
ehea_create_busmap_callback.
Signed-off-by: Hannes Hering <hering2@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Fix typo in ehea_h_query_ehea() which prevents building when DEBUG is on.
Signed-off-by: Sebastien Dugue <sebastien.dugue@bull.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The mutex is released on a successful return, so it would seem that it
should be released on an error return as well.
The semantic patch finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression l;
@@
mutex_lock(l);
... when != mutex_unlock(l)
when any
when strict
(
if (...) { ... when != mutex_unlock(l)
+ mutex_unlock(l);
return ...;
}
|
mutex_unlock(l);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
iph->tot_len is stored in network byte order, so access it using
ntohs(). This doesn't have any real world impact on ehea, since ehea
only exists for big-endian platfroms (at the moment at least) but fixing
this gets rid of a sparse warning and avoids having a bad example in the
tree.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
When ehea_stop is called the function
cancel_work_sync(&port->reset_task) is used to ensure
that the reset task is not running anymore. We need an
additional flag to ensure that it can not be scheduled
after this call again for a certain time.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Required to allow distros to easily detect when ehea
module needs to be loaded
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
A mutex has to be replaced by spinlocks as it can be called from
a context which does not allow sleeping.
The kzalloc flag GFP_KERNEL has to be replaced by GFP_ATOMIC
for the same reason.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
If the RTNL is held when we invoke flush_scheduled_work() we could
deadlock. One such case is linkwatch, it is a work struct which tries
to grab the RTNL semaphore.
The most common case are net driver ->stop() methods. The
simplest conversion is to instead use cancel_{delayed_}work_sync()
explicitly on the various work struct the driver uses.
This is an OK transformation because these work structs are doing
things like resetting the chip, restarting link negotiation, and so
forth. And if we're bringing down the device, we're about to turn the
chip off and reset it anways. So if we cancel a pending work event,
that's fine here.
Some drivers were working around this deadlock by using a msleep()
polling loop of some sort, and those cases are converted to instead
use cancel_{delayed_}work_sync() as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
eHEA has to call firmware functions in order to change the mac address
of a logical port. This patch checks if the logical port is up
when calling the register / deregister mac address calls. If the port
is down these firmware calls would fail and are therefore not executed.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Fixes the following use after free oops:
ehea: Reboot: freeing all eHEA resources
Unable to handle kernel paging request for data at address 0x6b6b6b6b6b6b6c5b
Faulting instruction address: 0xd000000000354488
cpu 0x0: Vector: 300 (Data Access) at [c00000002ec6f310]
pc: d000000000354488: .ehea_shutdown_single_port+0x50/0x78 [ehea]
lr: d00000000035447c: .ehea_shutdown_single_port+0x44/0x78 [ehea]
sp: c00000002ec6f590
msr: 8000000000009032
dar: 6b6b6b6b6b6b6c5b
dsisr: 40000000
current = 0xc0000000281412e0
paca = 0xc0000000006df300
pid = 10930, comm = reboot
enter ? for help
[c00000002ec6f590] d00000000035d64c .ehea_remove+0x44/0x124 [ehea] (unreliable)
[c00000002ec6f630] c000000000319f88 .of_platform_device_remove+0x40/0x58
[c00000002ec6f6a0] c000000000291018 .__device_release_driver+0xb0/0xf0
[c00000002ec6f730] c000000000291120 .driver_detach+0xc8/0xfc
[c00000002ec6f7c0] c00000000028fe24 .bus_remove_driver+0xb4/0x114
[c00000002ec6f850] c000000000291768 .driver_unregister+0x54/0x74
[c00000002ec6f8e0] c00000000031a0c8 .of_unregister_driver+0x14/0x28
[c00000002ec6f950] c000000000023ba0 .ibmebus_unregister_driver+0x10/0x24
[c00000002ec6f9c0] d000000000354180 .ehea_reboot_notifier+0x30/0x4c [ehea]
[c00000002ec6fa40] c0000000003c95a8 .notifier_call_chain+0x5c/0xcc
[c00000002ec6fae0] c000000000082cd4 .__blocking_notifier_call_chain+0x70/0xb0
[c00000002ec6fb90] c000000000075cf8 .kernel_restart_prepare+0x24/0x58
[c00000002ec6fc10] c000000000075f0c .kernel_restart+0x20/0x6c
[c00000002ec6fc90] c000000000078674 .sys_reboot+0x1d4/0x290
[c00000002ec6fe30] c0000000000086ac syscall_exit+0x0/0x40
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The eHEA driver uses the recently modified walk_memory_resource for powerpc
functionality to detect the memory layout. It further uses the memory hotplug
notifiers to catch memory hotplug events.
Signed-off-by: Hannes Hering <hering2@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
ehea_flush_sq() and ehea_purge_sq() should be static.
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Thomas Klein <osstklei@de.ibm.com>
Cc: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/ehea/ehea_main.c
drivers/net/wireless/iwlwifi/Kconfig
drivers/net/wireless/rt2x00/rt61pci.c
net/ipv4/inet_timewait_sock.c
net/ipv6/raw.c
net/mac80211/ieee80211_sta.c
|
|
This patch fixes two weaknesses in send/receive packet handling which may
lead to kernel panics during DLPAR memory add operations.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Convert the port_lock to a mutex. There is also some additional cleanup. The
line length inside the ehea_rereg_mrs was getting long so I made some
adjustments to shorten them.
[akpm@linux-foundation.org: dec99ification]
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Cc: Christoph Raisch <raisch@de.ibm.com>
Cc: Jan-Bernd Themann <themann@de.ibm.com>
Cc: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Convert the ehea_bcmc_regs.lock to a mutex.
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Cc: Christoph Raisch <raisch@de.ibm.com>
Cc: Jan-Bernd Themann <themann@de.ibm.com>
Cc: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Nested locks always need to be taken in the same order. This change factors
out the ehea_fw_handles.lock to make the locking order consistent.
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Cc: Christoph Raisch <raisch@de.ibm.com>
Cc: Jan-Bernd Themann <themann@de.ibm.com>
Cc: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Converted the ehea_fw_handles.lock to a mutex.
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Cc: Christoph Raisch <raisch@de.ibm.com>
Cc: Jan-Bernd Themann <themann@de.ibm.com>
Cc: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Converted the dlpar_mem_lock. With a bit of cleanup, I converted to
DEFINE_MUTEX() instead of a runtime init. I also made the lock static.
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Cc: Christoph Raisch <raisch@de.ibm.com>
Acked-by: Jan-Bernd Themann <themann@de.ibm.com>
Cc: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Indicate that HEA calculates IPv4 checksums only
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This patch adds kdump support to the ehea driver. As the firmware doesn't free
resource handles automatically, the driver has to run an as simple as possible
free resource function in case of a crash shutdown. The function iterates over
two arrays freeing all resource handles which are stored there. The arrays are
kept up-to-date during normal runtime. The crash handler fn is triggered by the
recently introduced PPC crash shutdown reg/unreg functions.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Due to changes in the struct device_driver there is no direct
access to its kobj any longer. The kobj was used to create
sysfs links between eHEA ethernet devices and the driver.
This patch removes the affected sysfs links to resolve
the build problems.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cc: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Doug Maxey <dwm@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cc: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Doug Maxey <dwm@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cc: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Doug Maxey <dwm@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cc: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Doug Maxey <dwm@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cc: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Doug Maxey <dwm@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prevent driver from brawly logging packet checksum errors.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Using own tx_packets counter instead of firmware counters.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
eHEA resources that are allocated via H_CALLs have a unique identifier each.
These identifiers are necessary to free the resources. A reboot notifier
is used to free all eHEA resources before the indentifiers get lost, i.e
before kexec starts a new kernel.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
