Age | Commit message (Collapse) | Author |
|
Some usage was only sizing a pointer rather than the data type.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to set/clear the mac address register when the link goes up/down
respectively. Without this both ports of a 2-port device can end up
with the same mac address in a bonding scenario.
The new ql_link_on() and ql_link_off() will also be used in handling
certain firmware events.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This addes functionality to set/clear the MAC address in the hardware
when the link goes up/down.
The MAC address register is persistent across function resets. In
bonding the same address can bounce from one port to the other. This
can cause packets to be delivered to the wrong port.
This patch clears the MAC address in the hardware when the link is down
and sets it when the link comes up.
It was found that pulling/pushing the cable from one port to another
causes the same MAC address to be in both ports.
The next patch in this series will use this functionality as well.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The caller will free acquired resouces if a failure occurs.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We were turning on the carrier without verifying the link was up.
This adds link up to the link initialize check before turning carrier
on.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Not clearing the routing bits can cause frames to erroneously get routed to
management processor.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The hardware semaphore covers the configuration register as well as the
ICB registers. The ICB high and low regs contain the address of the
initialization control block and the config register is used to signal
the hardware that a block is ready to be downloaded. Currently we were
only protecting the ICB regs. This changes expands to cover the config
register as well.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:
Documentation/feature-removal-schedule.txt
drivers/scsi/fcoe/fcoe.c
net/core/drop_monitor.c
net/core/net-traces.c
|
|
fix ETIMEOUT -> ETIMEDOUT typos
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
RX buffer rings can be comprised of non-contiguous fixed
size chunks of memory. The ring is given to the hardware
as a pointer to a location that stores the location of
the queue. If the queue is greater than 4096 bytes then
the hardware gets a list of said pointers.
This patch addes the necessary logic to generate the list if
the queue size exceeds 4096.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The alignment was on size of queue boundary, but the hardware
only requires 4-byte alignment.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently we support only PCIe NIC functions zero and one, and FCoE
functions as 3 and 4. Future configurations can mix these up in any
fashion.
This patch removes the 0-1 dependancy and allows usage of any of the 4
functions. We also find the alternate NIC function (if exist) and
determine our port number based on the comparison of the two functions:
Lower function number gets first port, higher function gets second port.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extract either manufacturer or Bladecenter Open Fabric
Manager (BOFM) MAC address. BOFM may indicate an
alternate MAC address. This patch honors that request
by extracting the MAC address from a different
flash location if a flag is set.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The max frame size register is set higher than the MTU to
accomodate FCoE frames.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Not necessary if hardware supports 65536 as it's the default setting.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is used by driver banner and ethtool info.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Followup of commits 9d21493b4beb8f918ba248032fefa393074a5e2b
and 08baf561083bc27a953aa087dd8a664bb2b88e8e
(net: tx scalability works : trans_start)
(net: txq_trans_update() helper)
Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Multi queue drivers can
avoid one cache miss (on dev->trans_start) in their start_xmit()
handler.
Exceptions are NETIF_F_LLTX drivers (vxge & tehuti)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/igb/igb_main.c
drivers/net/qlge/qlge_main.c
drivers/net/wireless/ath9k/ath9k.h
drivers/net/wireless/ath9k/core.h
drivers/net/wireless/ath9k/hw.c
|
|
With some asic configurations xmit of frames smaller than 60 bytes may
fail.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Moving netif_napi_del() up the call chain so it will get called from all
exit points.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Chip does not do UDP checksum when fragmentation occurs.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This was introduced in an earlier net-next patch.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With some asic configurations xmit of frames smaller than 60 bytes may
fail.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Moving netif_napi_del() up the call chain so it will get called from all
exit points.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is nothing to contend with it.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The completion interrupt disable routine is only called from the ISR, so
there is no need for irqsave/restore.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Chip does not do UDP checksum when fragmentation occurs.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Get rid of extraneous ql_cycle_adapter. It's only called from the one
place.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This worker and it's supporting routines are used for
IDC 'inter-device-communication' events that require
an ACK mailbox command be sent to allow completion
of the request. These requests are originated by
another function wanting to change some common
port paramters. Typical example would be:
1) Change max TX/RX frame size allowed.
2) Change pause parameters.
3) Change loopback mode.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds functionality to get and set port parameters.
Currently it is used to set maximum TX/RX frame sizes. This process is
also capable of setting:
1) Pause type: Standard or Priority based.
2) Loop back mode.
3) Enable Jumbo frame mode (included here...)
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This device has more firmware support for link management, setting
TX and RX maximum frame sizes.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Get rid of some noise that is for debug only.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This organizes a few calls into a function table to enable adding new
devices.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is not a logical change but rather a move of the inbound firmware event
handler into it's own function as it will later be called by the outbound
path.
The addition of the mutex is to create exclusive access to the mailbox
commands between inbound and outbound handling.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently there are two paths for filling rx buffer queues. One is
used during initialization and the other during runtime. This patch
removes ql_alloc_sbq_buffers() and ql_alloc_lbq_buffers() and replaces
them with a call to the runtime functions ql_update_lbq() and
ql_update_sbq().
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RX Buffers are refilled in chunks of 16 at a time before notifying the
hardware with a register write. This can cause several writes to take
place in a given napi poll call. This change causes the write to take place
only once at the end of the call.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of taking/giving the hw semaphore repeatedly when iterating over
several frame to queue route settings, we have the caller hold it until
all are done.
This reduces PCI bus chatter and possible waits.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of taking/giving the semaphore repeatedly when iterating over
several adderesses, we have the caller hold it until all are done. This
reduces PCI bus chatter and possible waits.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Setting MAC addresses and routing frames to various queues will need to
be done in response to firmware events as well as during initialization.
This change encapsulates the facilities into a single call that can
later me made from other places.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|