aboutsummaryrefslogtreecommitdiff
path: root/drivers/net/sfc
AgeCommit message (Collapse)Author
2009-01-30sfc: Replace stats_enabled flag with a disable countBen Hutchings
Currently we use a spin-lock to serialise statistics fetches and also to inhibit them for short periods of time, plus a flag to enable/disable statistics fetches for longer periods of time, during online reset. This was apparently insufficient to deal with the several reasons for stats being disabled. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-30sfc: SFX7101/SFT9001: Fix AN advertisementsBen Hutchings
All 10Xpress PHYs require autonegotiation all the time; enforce this in the set_settings() method and do not treat it as a workaround. Remove claimed support for 100M HD mode since it is not supported by current firmware. Do not set speed override bits when AN is enabled, and do not use register 1.49192 for AN configuration as it can override what we set elsewhere. Always set the AN selector bits to 1 (802.3). Fix confusion between Next Page and Extended Next Page. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-30sfc: SFT9001: Always enable XNP exchange on SFT9001 rev BBen Hutchings
This workaround is not specific to rev A. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-30sfc: Update board info for hardware monitor on SFN4111T-R5 and laterBen Hutchings
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-30sfc: Test for PHYXS faults whenever we cannot test link state bitsSteve Hodgson
Depending on the loopback mode, there may be no pertinent link state bits. In this case we test the PHYXS RX fault bit instead. Make sure to do this in all cases where there are no link state bits. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-30sfc: Reinitialise the PHY completely in case of a PHY or NIC resetSteve Hodgson
In particular, set pause advertising bits properly. A PHY reset is not necessary to recover from the register self-test, so use a "invisible" reset there instead. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-30sfc: Fix post-reset MAC selectionSteve Hodgson
Modify falcon_switch_mac() to always set NIC_STAT_REG, even if the the MAC is the same as it was before. This ensures that the value is correct after an online reset. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-30sfc: SFN4111T: Fix GPIO sharing between I2C and FLASH_CFG_1Ben Hutchings
Change sfn4111t_reset() to change only GPIO output enables so that it doesn't break subsequent I2C operations. Update comments to explain exactly what we're doing. Add a short sleep to make sure the FLASH_CFG_1 value is latched before any subsequent I2C operations. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-30sfc: SFT9001: Fix speed reporting in 1G PHY loopbackSteve Hodgson
Instead of disabling AN in loopback, just prevent restarting AN and override the speed in sft9001_get_settings(). Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-30sfc: SFX7101: Remove workaround for bad link trainingSteve Hodgson
Early versions of the SFX7101 firmware could complete link training in a state where it would not adequately cancel noise (Solarflare bug 10750). We previously worked around this by resetting the PHY after seeing many Ethernet CRC errors. This workaround is unsafe since it takes no account of the interval between errors; it also appears to be unnecessary with production firmware. Therefore remove it. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-30sfc: SFT9001: Enable robust link trainingSteve Hodgson
Enable a firmware option that appears to be necessary for reliable operation. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-11sfc: SFT9001: Fix condition for LNPGA power-offBen Hutchings
Only the SFX7101 requires software power control. This was incorrectly being applied to the SFT9001 rev A as well. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-07net: sfc: Use pci_clear_master() to disable bus masteringBen Hutchings
pci_disable_device() disables many features, like MSI-X, which we never reenable in efx_reset(). Further, calls to pci_enable_device() and pci_disable_device() must be matched since the nesting count was introduced, so switch to using pci_clear_master() instead. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2008-12-26net: Fix warning fallout from recent NAPI interface changes.David S. Miller
When we removed the network device argument from several NAPI interfaces in 908a7a16b852ffd618a9127be8d62432182d81b4 ("net: Remove unused netdev arg from some NAPI interfaces.") several drivers now started getting unused variable warnings. This fixes those up. Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26sfc: If AN is enabled, always read speed/duplex from the AN advertising bitsBen Hutchings
When AN is enabled and the link is down the speed/duplex control bits will not be meaningful. Use the advertising bits instead, and mask them with the LPA bits if and only if AN is complete (as before). Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26sfc: When disabling the NIC, close the device rather than unregistering itBen Hutchings
This should reduce user confusion and may also aid recovery (ioctls will still be available). Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26sfc: SFT9001: Add cable diagnosticsBen Hutchings
The SFT9001 firmware implements cable diagnostics; run those and include their results in a self-test. In case of a cable fault, do not fail the self-test as a whole; only faults in the NIC should cause that. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26sfc: Add support for multiple PHY self-testsBen Hutchings
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26sfc: Merge top-level functions for self-testsBen Hutchings
Pass in ethtool test flags to determine which tests to run. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26sfc: Clean up PHY mode management in loopback self-testBen Hutchings
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26sfc: Fix unreliable link detection in some loopback modesBen Hutchings
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26sfc: Generate unique names for per-NIC workqueuesBen Hutchings
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-22net: Remove unused netdev arg from some NAPI interfaces.Neil Horman
When the napi api was changed to separate its 1:1 binding to the net_device struct, the netif_rx_[prep|schedule|complete] api failed to remove the now vestigual net_device structure parameter. This patch cleans up that api by properly removing it.. Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12sfc: Version 2.3Ben Hutchings
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12sfc: Fix synchronisation of efx_mtd_{probe,rename,remove}Ben Hutchings
Currently efx_mtd_rename() can race with the probe() and remove() functions. Move probe() before device registration and remove() after unregistration. Move initialisation/update of all names based on the netdev name into a new function and call it under the RTNL immediately after registration. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12sfc: Use kzalloc() to ensure struct efx_spi_device is fully initialisedBen Hutchings
Currently the mtd field is not initialised early enough. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12sfc: Treat probe as unsuccessful if it scheduled a resetSteve Hodgson
From: Steve Hodgson <shodgson@solarflare.com> efx_pci_probe_main() can return success despite a reset being scheduled. Catch this and retry or abort probe depending on the reset type. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12sfc: Use model numbers for PHY type namesBen Hutchings
Some of the PHY type names are overly generic. Change them to include the model numbers of the PHYs they represent. Correct the model number reference at the top of xfp_phy.c. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12sfc: Use mutex_lock_interruptible() for ethtool EEPROM accessBen Hutchings
ethtool must contend with the MTD driver for the SPI bus lock, which may carry out long operations such as flash erase. Allow it to be interrupted while waiting. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12sfc: Specify a meaningful component for loopback RX-side and PHY testsBen Hutchings
Our ethtool self-test result names each begin with a component name. For some results this is "port0", which is not very meaningful. Change that to "rx" or "phy" as appropriate. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12sfc: Remove leading spacesBen Hutchings
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12sfc: Add support for SFN4111TBen Hutchings
Add support code for the SFN4111T 100/1000/10GBASE-T reference design, based in part on the existing code for the SFE4001. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12sfc: Add support for Solarflare 10Xpress SFT9001Ben Hutchings
Add type codes for the new PHY and rename the SFX7101 type code. Add definition of clause 22 extension MMD. Adapt the 10Xpress SFX7101 code to support the SFT9001 as well. Clean up register definitions. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12sfc: Rework MAC, PHY and board event handlingBen Hutchings
From: Steve Hodgson <shodgson@solarflare.com> MAC, PHY and board events may be separately enabled and signalled. Our current arrangement of chaining the polling functions can result in events being missed. Change them to be more independent. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12sfc: Implement auto-negotiationBen Hutchings
Add infrastructure for auto-negotiation of speed, duplex and flow control. When using 10Xpress, auto-negotiate flow control. While we're at it, clean up the code to warn when partner is not 10GBASE-T capable. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12sfc: Add support for sub-10G speedsBen Hutchings
The SFC4000 has a separate MAC for use at sub-10G speeds. Introduce an efx_mac_operations structure with implementations for the two MACs. Switch between the MACs as necessary. PHY settings are independent of the MAC, so add get_settings() and set_settings() to efx_phy_operations. Also add macs field to indicate which MACs the PHY is connected to. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12sfc: Clean up MDIO flag settingBen Hutchings
We often want to set or clear a flag in an MDIO register, but avoid writing if no change is required since this can have side-effects. Encapsulate this in a function, mdio_clause45_set_flag(). Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12sfc: Clean up board identificationBen Hutchings
Remove kluge for development boards with unspecified board type. Remove assumption of contiguous board type code assignments. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12sfc: Add phy_type device attributeBen Hutchings
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12sfc: Add support for MMDs numbered >15Ben Hutchings
Combine DEVS0 and DEVS1 registers into a 32-bit mask instead of reading just DEVS0. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12sfc: Remove MII extension cruftBen Hutchings
Replace efx_nic::link_options bitfield with link_speed (speed in Mbit/s) and link_fd (full duplex flag). Remove broken auto-negotiation functions. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12sfc: Don't count RX checksum errors during loopback self-testBen Hutchings
The loopback self-test checks that IP packets with incorrect checksums are not altered when sent on a queue with checksum generation off. These should not contribute to RX error statistics. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12sfc: Abbreviate self-test names so they are not truncatedBen Hutchings
Change "channel" to "chan". Shorten PHY loopback names. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12sfc: Provide hints to irqbalance daemonBen Hutchings
Allocate IRQs with the name format <device>[-<type>]-<number> so that future versions of irqbalanced understand what we're doing. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12sfc: Add option to use a separate channel for TX completionsNeil Turton
In a bidirectional forwarding test, we find that the best performance is achieved by sending the TX completion interrupts from one NIC to a CPU which shares an L2 cache with RX completion interrupts from the other NIC. To facilitate this, add an option (through a module parameter) to create separate channels for RX and TX completion with separate IRQs when MSI-X is available. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12sfc: Restore phy_flash_cfg module parameterBen Hutchings
This is needed for recovery in case a PHY firmware upgrade is aborted. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12sfc: Work around unreliable strap pinsBen Hutchings
The SFC4000 has strap pins indicating the presence of SPI flash and/or EEPROM. These pins are also used for GPIO, and in some cases they may be read wrongly at reset. However, on production boards it must boot from one or the other device, so we can assume the boot device is present and read the board config from there. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12sfc: Clean up waits for flash/EEPROM operationsBen Hutchings
Make falcon_spi_wait() ignore the write timer - it is only relevant to write commands, it only works for the device that contains VPD, and it might not be initialised properly at all. Rename falcon_spi_fast_wait() to falcon_spi_wait_write(), reflecting its use, and make it wait up to 10 ms (not 1 ms) since buffered writes to EEPROM may take this long to complete. Make both wait functions sleep instead of busy-waiting. Replace wait for command completion at top of falcon_spi_cmd() with a single poll; no command should be running when the function starts. Correct some comments. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12sfc: Make reset_workqueue driver-global rather than per-NICSteve Hodgson
Each reset is serialised by the rtnl_lock anyway, so there's no win per-NIC. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-12sfc: Correct interpretation of second param to ethtool phys_id()Ben Hutchings
A value of 0 means indefinite repetition (until interrupted). Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-22 06:56:05 +0000