| Age | Commit message (Collapse) | Author |
|---|
|
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6: (230 commits)
[SPARC64]: Update defconfig.
[SPARC64]: Fix 2 bugs in huge page support.
[SPARC64]: CONFIG_BLK_DEV_RAM fix
[SPARC64]: Optimized TSB table initialization.
[SPARC64]: Allow CONFIG_MEMORY_HOTPLUG to build.
[SPARC64]: Use SLAB caches for TSB tables.
[SPARC64]: Don't kill the page allocator when growing a TSB.
[SPARC64]: Randomize mm->mmap_base when PF_RANDOMIZE is set.
[SPARC64]: Increase top of 32-bit process stack.
[SPARC64]: Top-down address space allocation for 32-bit tasks.
[SPARC64] bbc_i2c: Fix cpu check and add missing module license.
[SPARC64]: Fix and re-enable dynamic TSB sizing.
[SUNSU]: Fix missing spinlock initialization.
[TG3]: Do not try to access NIC_SRAM_DATA_SIG on Sun parts.
[SPARC64]: First cut at VIS simulator for Niagara.
[SPARC64]: Fix system type in /proc/cpuinfo and remove bogus OBP check.
[SPARC64]: Add SMT scheduling support for Niagara.
[SPARC64]: Fix 32-bit truncation which broke sparsemem.
[SPARC64]: Move over to sparsemem.
[SPARC64]: Fix new context version SMP handling.
...
|
|
|
|
Sun does't put an SEEPROM behind the tigon3 chip, among other things,
so accesses to these areas just give bus timeouts.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 40-bit DMA workaround recently implemented for 5714, 5715, and
5780 needs to be expanded because there may be other tg3 devices
behind the EPB Express to PCIX bridge in the 5780 class device.
For example, some 4-port card or mother board designs have 5704 behind
the 5714.
All devices behind the EPB require the 40-bit DMA workaround.
Thanks to Chris Elmquist again for reporting the problem and testing
the patch.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
The Coverity checker spotted this dead code (note that (clock_ctrl == 7)
is already handled above).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Add DMA workaround for chips that do not support full 64-bit DMA
addresses.
5714, 5715, and 5780 chips only support DMA addresses less than 40
bits. On 64-bit systems with IOMMU, set the dma_mask to 40-bit so
that pci_map_xxx() calls will map the DMA address below 40 bits if
necessary. On 64-bit systems without IOMMU, set the dma_mask to
64-bit and check for DMA addresses exceeding the limit in
tg3_start_xmit().
5788 only supports 32-bit DMA so need to set the mask appropriately
also.
Thanks to Chris Elmquist at SGI for reporting and helping to debug
the problem on 5714.
Thanks to David Miller for explaining the HIGHMEM and DMA stuff.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Some Sun parts don't have PCI_VENDOR_ID_SUN in the subsystem
vendor ID. So add another fallback test, which is the name
of the OBP firmware device tree node. If it's a Sun part we'll
get "network", else it will be named "ethernet".
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure tg3_reset_task() is flushed in the close and suspend paths
as noted by Jeff Garzik.
In the close path, calling flush_scheduled_work() may cause deadlock
if linkwatch_event() is on the workqueue. linkwatch_event() will try
to get the rtnl_lock() which is already held by tg3_close(). So
instead, we set a flag in tg3_reset_task() and tg3_close() polls
the flag until it is cleared.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add nvram lock count so that calls to tg3_nvram_lock()/unlock() can
be nested. Add error checking to all callers of tg3_nvram_lock()
where appropriate. To prevent nvram lock failures after halting the
firmware, it is also necessary to release firmware's nvram lock in
tg3_halt_cpu().
Update version to 3.48.
Based on David Miller's initial patch.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Turning struct iphdr::tot_len into __be16 added sparse warning.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To help in reducing the number of include dependencies, several files were
touched as they were getting needed headers indirectly for stuff they use.
Thanks also to Alan Menegotto for pointing out that net/dccp/proto.c had
linux/dccp.h include twice.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Resubmitting after recommendation to use GET_REG32_1() instead of
GET_REG32_LOOP(..., 1). Retested. Problem remains fixed.
Prevent tg3_get_regs() from reading reserved and undocumented registers
at RX_CPU_BASE and TX_CPU_BASE offsets which caused hostile behavior
on PCIe platforms.
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Skip the memory 0xb50 to 0x1000 during "ethtool -t" memory test.
Overwriting memory in this region can cause ASF problems.
Update version and release date.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The tw32_f() function (register write with immediate read flush) can
hang when used on some registers to switch clock frequencies and
power. A new tw32_wait_f() is added for such registers with the
delay before the read and after the read.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add some missing workarounds in tg3_set_power_state():
1. Workaround to prevent overdrawing current on 5714.
2. Do not power down 5700's PHY because of hw limitation.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Locate the pdev_peer for dual port 5714 NIC devices in addition to
5704 devices. The name is also changed to tg3_find_peer() from
tg3_find_5704_peer(). It is also necessary to call netdev_priv() to
get to the peer's private tg3 structure.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the following bugs in tg3_set_power_state():
1. Both WOL and ASF flags require switching to aux power.
2. Add a missing handshake with firmware to enable WOL.
3. Turn off the PHY if both WOL and ASF are disabled.
4. Add nvram arbitration before halting the firmware.
5. Fix tg3_setup_copper_phy() to switch to 100Mbps when
changing to low power state.
Update revision and date.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the dual-port 5704 is configured as a single-port device with
only one PCI function, it would trigger a BUG() condition in
tg3_find_5704_peer(). This fixes the problem by returning its
own pdev if the peer cannot be found.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix tg3_suspend() and tg3_resume() by clearing and setting the
TG3_FLAG_INIT_COMPLETE flag when appropriate. tg3_set_power_state()
looks at TG3_FLAG_INIT_COMPLETE on the peer device to determine
when to appropriately switch to aux power.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The nvram arbitration rules were not strictly followed in a few places
and this could lead to reading corrupted values from the nvram.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
[ Move assosciated code comment to the correct spot, and
update driver version and release date -DaveM ]
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This one from my DMA_{32,64}BIT_MASK series did not seem to make it
through to upstream.
Use the DMA_{32,64}BIT_MASK constants from dma-mapping.h when calling
pci_set_dma_mask() or pci_set_consistent_dma_mask()
This patch includes dma-mapping.h explicitly because it caused errors
on some architectures otherwise.
See http://marc.theaimsgroup.com/?t=108001993000001&r=1&w=2 for details
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
|
|
Update version and reldate and add more sanity checking to
tg3_set_settings().
Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
Change the ASF heart beat to 5 seconds for faster detection of system
crash. The driver sends the heartbeat every 2 seconds and the ASF
firmware will timeout and reset the device if no heartbeat is received
after 5 seconds. The old scheme of 2 minutes is ineffective.
tg3_write_mem_fast() is added to speed up the IO to send the heartbeat.
When no workaround is needed, it will use direct MMIO to memory space
to write to memory.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
Add complete support for 5714/5715. These chips are very similar to
5780 so the changes are very trivial. A TG3_FLG2_5780_CLASS flag is
added to identify these chips.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Test for VIA K8T800 north bridge instead of AMD K8 HyperTransport
bridge based on new information from Andi Kleen. The AMD
HyperTransport interface is not responsible for PCI transactions
and so the re-ordering is more likely done by the VIA north bridge.
This code is subject to change if we get more information from AMD
or VIA.
PCI Express devices are excluded from doing the read flush since all
chipsets in the write_reorder list are PCI chipsets.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix interrupt test handler by adding check for IRQ assertion in
PCI_STATE register in addition to the status block updated bit.
Add test for valid ethernet address in tg3_set_mac_addr().
Add tg3_bus_string() to setup the PCI bus speed/width string for all
PCI/PCIX/PCI Express devices. This is used to print the bus type
during init_one().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix 5780 PHY related problems:
1. MAC_RX_MODE reset must be done before setting up the MAC_MODE
register on 5705_PLUS chips or the chip will stop receiving after
a while. The MAC_RX_MODE reset is needed to prevent intermittently
losing the first receive packet on serdes chips.
2. Skip MAC loopback test on 5780 because of hardware errata. Normal
traffic including PHY loopback is not affected by the errata.
3. PHY loopback fails intermittently on 5708S and this is fixed by
putting the PHY in loopback mode first before programming the MAC
mode register. A MAC_RX_MODE reset is also added.
4. Return -EINVAL in tg3_nway_reset() if device is in TBI mode. Allow
nway_reset if 5780S is in parallel detect mode.
5. Add missing PHY IDs in KNOWN_PHY_ID() macro.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix and simplify the workaround code for the 4GB boundary tx buffer
hardware bug.
1. Need to unmap the original SKB's dma addresses if a new SKB cannot
be allocated.
2. Need to pass the base flag to tigon3_4gb_hwbug_workaround() or TSO
won't work properly.
3. The guilty entry and length parameters for
tigon3_4gb_hwbug_workaround() are removed as they are not necessary.
4. Remove assumption that only one fragment can hit the 4GB boundary.
Another fragment can hit 8GB for example.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change 0 to NULL where appropriate.
Signed-off-by: Peter Hagervall <hager@cs.umu.se>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Thanks to Andy Stewart for the report and testing
debug patches from Michael Chan.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead, count them as part of rx_missed_errors.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the status tag to determine if there are new events in
tg3_interrupt_tagged(). We discussed about this a while ago with Grant
Grundler and DaveM. This scheme makes it unnecessary to clear the
updated bit in the status block when using tagged mode, and only
a simple comparison is needed to determine if there are new events.
The tp->lock around netif_rx_complete() and tg3_restart_ints() is also
removed. It is unnecessary with DaveM's new locking scheme.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove unnecessary status block accesses in tg3_msi(). Since MSI is
not shared, it is unnecessary to read the status block to determine if
there are any new events in the MSI handler. It is also unnecessary to
clear the updated bit in the status block.
Since the poll list is per-cpu, tg3_poll() will be scheduled to run on
the same CPU that received the MSI. Prefetches for the status block
and the next rx descriptors are added in tg3_msi() to improve their
access times when tg3_poll() runs.
In the non-MSI irq handlers, we need to check the status block because
interrupts may be shared. Only prefetches for the next rx descriptors
are added.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Improve ethtool loopback self test by adding PHY loopback to the
existing MAC loopback test.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Minor SerDes bug fixes for 5780S and nvram bug fixes for 5780 and
5752.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is similar to Eric Dumazet's tx_lock patch for tg3 but takes it
one step further to eliminate the tx_lock in the tx_completion path
when the tx queue is not stopped.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Found a bug while reviewing the patches the second time.
The TG3_FLAG_TXD_MBOX_HWBUG flag is set after the register access
methods have been determined. This patch fixes it by moving it up before
the various access methods are assigned.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
