| Age | Commit message (Collapse) | Author |
|---|
|
The Qdiv roundup routine is essentially a fixed-point
division algorithm, using only integer math.
However, the version in the specs had a major error
that has been recently fixed (a missing quotient++).
Replace Qdiv roundup with a rewritten, simplified version.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The RC calibration code has some typos - fix them.
Also, make the default channel 7, as channel 1 is still
broken (only channels 7 and 8, and occasionally 9 work).
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This add hardware tkip for b43.
Signed-off-by: Gregor Kowski <gregor.kowski@gmail.com>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Larry has started re-checking all current routines against a new
version of the Broadcom MIPS driver. This patch implements the first
round of changes he documented on the specs wiki.
Also remove a few FIXMEs regarding missing initial values for variables
with dynamic initial values where reading the values has been implemented.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The specs are beginning to support rev3 LP-PHYs - implement one of
the changes needed for rev3 support.
Also, in the new MIPS driver, the "Japan TX filter" was renamed to
"analog TX filter init" - however, calling it "init" is confusing,
so name it "set analog filter", with a comment for easier future
identification.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Call set_tx_power_control with a LPPHY_TXPCTL rather than an
LPPHY_TX_PWR_CTL_CMD_MODE.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Check the mode the hardware is in, not the mode we used the last time.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Over time, a whole bunch of drivers have come up
with their own scheme to delay the configure_filter
operation to a workqueue. To be able to simplify
things, allow configure_filter to sleep, and add
a new prepare_multicast callback that drivers that
need the multicast address list implement. This new
callback must be atomic, but most drivers either
don't care or just calculate a hash which can be
done atomically and then uploaded to the hardware
non-atomically.
A cursory look suggests that at76c50x-usb, ar9170,
mwl8k (which is actually very broken now), rt2x00,
wl1251, wl1271 and zd1211 should make use of this
new capability.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Larry has reported success getting scan data with an LP-PHY device,
so it's probably time to release LP-PHY support for testing.
Also disable 802.11a support for now, as 802.11a currently causes
the driver to panic on startup (NULL pointer dereference).
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The spec for initializing the B2062 radio have changed recently,
update the code to match the changes.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
I missed the "+16" part of the instruction in the specs.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
A few typos have been discovered in both the specs and the code.
This patch fixes them.
Also use lpphy_op_switch_channel consistently, and make all users
of it print its return value for easier debugging.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The channel switch routine had a whole instruction missing. Add it.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The spec had some nasty typos, and a large part of the rev0/1 BB
init procedure was also missing. Fix these.
Also make the init-time channel switch debuggable.
(The change from -EINVAL to -EIO is simply to make it possible
to distinguish the PLL charge pump error from a channel-not-found
error.)
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Don't drop all packets received from an LP-PHY with WARN_ON.
Also update a comment with LP-specific information.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This should fix the remaining WARN_ON.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Rev2+ never needs to have gain tables adjusted according to the spec.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
-Enable rate memory init for LP-PHY (same as G and N-PHY).
-Mark rev.2 LP-PHYs with the B2063 radio as supported.
-Allow using the 5GHz band on LP-PHYs.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add support for loading LP-PHY firmware to b43_try_request_fw.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
-Move pdiv from lpphy_2062_init to struct b43_phy_lp.
-Add channel table for the B2062 radio.
-Add code for tuning the B2062 radio to channel.
-Add error handling to op_switch_channel, and use it for both radios.
Rev0/1/B2062 will now hopefully show some signs of life, though
it won't work at full performance, as calibration is still missing.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Rev.2+/B2063 will now hopefully show some signs of life, though
it won't work at full performance, as calibration is still missing.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The HW TX power control init still needs work.
The SW init is complete according to the specs.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The V4 dummy transmission has two extra bools in its prototype,
so update all callers with the 2 bools.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Also implement get/set BB mult, get/set TX gain, set RX gain,
disable/restore CRS, run/stop DDFS, RX IQ est and QDIV roundup
in the process.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Make it possible to write individual gain table entries.
Allow gain table entries to be written outside gain table init.
Add version-agnostic helpers for writing gain tables.
Use the new TX gain table helpers during table init.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Some of the new variables in b43_phy_lp appear to be dead code in
the vendor driver; they will be removed if they remain unused when
LP-PHY implementation is finished.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
I completely missed the "one's complement" instruction from the specs.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The rev2+ BB init spec has changed behind us, and thus the code is
no longer up to date. Update the code to match the current specs.
Also implement save/restore dig filt state, as required by the
new specification.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Implement LP-PHY baseband table init for all revisions.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The v2+ radio init (B2063) is now complete, modulo BCM4325 support.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This fixes the hardware encryption keys index and array size handling.
Thanks to Gregor Kowski for reporting this issue.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Update a comment that still says IEEE80211_IF_TYPE instead of NL80211_IFTYPE.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The tkip hw support uncovered a bug in b43_write_probe_resp_template : it is
writing at the wrong shm offset, it is in the B43_SHM_SH_TKIPTSCTTAK
zone. Remove b43_write_probe_resp_template, b43_write_probe_resp_plcp
and b43_write_probe_resp_plcp because the probe response offload is
currently not supported by mac80211.
Signed-off-by: Gregor Kowski <gregor.kowski@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Make use of HostFlags defines in the LP-PHY code.
Fix fallout from the IEEE80211_IF_TYPE to NL80211_IFTYPE change.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add B2063 radio init code and tables for LP-PHY.
Rename structures common between B2062 and B2063 to B206X.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Implement baseband init for rev.0 and rev.1 LP PHYs. Convert boardflags_hi values to defines.
Implement b43_phy_copy for easier copying between registers, as needed by LP-PHY init.
Signed-off-by: Gábor Stefanik<netrolller.3d@gmail.com>
Cc: Michael Buesch<mb@bu3sch.de>
Cc: Larry Finger<larry.finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The tkip hw support uncovered a bug in b43_write_probe_resp_template : it is
writing at the wrong shm offset, it is in the B43_SHM_SH_TKIPTSCTTAK zone. This
patch comments these writes.
Signed-off-by: Gregor Kowski <gregor.kowski@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This fixes unaligned 32bit SHM-shared read/write access.
The low and high 16 bits were swapped.
It also adds a testcase for this to the chipaccess validation.
(Thanks to Albert Herranz for tracking down this bug.)
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The mac80211 workqueue exists to enable mac80211 and drivers
to queue their own work on a single threaded workqueue. mac80211
takes care to flush the workqueue during suspend but we never
really had requirements on drivers for how they should use
the workqueue in consideration for suspend.
We extend mac80211 to document how the mac80211 workqueue should
be used, how it should not be used and finally move raw access to
the workqueue to mac80211 only. Drivers and mac80211 use helpers
to queue work onto the mac80211 workqueue:
* ieee80211_queue_work()
* ieee80211_queue_delayed_work()
These helpers will now warn if mac80211 already completed its
suspend cycle and someone is trying to queue work. mac80211
flushes the mac80211 workqueue prior to suspend a few times,
but we haven't taken the care to ensure drivers won't add more
work after suspend. To help with this we add a warning when
someone tries to add work and mac80211 already completed the
suspend cycle.
Drivers should ensure they cancel any work or delayed work
in the mac80211 stop() callback.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
As shown in http://thread.gmane.org/gmane.linux.kernel.wireless.general/36497,
mac80211 has a bug that allows a call to the TX routine after the queues have
been stopped. This situation will only occur under extreme stress. Although
b43 does not crash when this condition occurs, it does generate a WARN_ON and
also logs a queue overrun message. This patch recognizes b43 is not at fault
and logs a message only when the most verbose debugging mode is enabled. In
the unlikely event that the queue is not stopped when the DMA queue becomes
full, then a warning is issued.
During testing of this patch with one output stream running repeated tcpperf
writes and a second running a flood ping, this routine was entered with
the DMA ring stopped about once per hour. The condition where the DMA queue is
full but the ring has not been stopped has never been seen by me.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Use %pM instead, and also remove stray variables
declared with DECLARE_MAC_BUF.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Within mac80211, we often need to copy the rx status into
skb->cb. This is wasteful, as drivers could be building it
in there to start with. This patch changes the API so that
drivers are expected to pass the RX status in skb->cb, now
accessible as IEEE80211_SKB_RXCB(skb). It also updates all
drivers to pass the rx status in there, but only by making
them memcpy() it into place before the call to the receive
function (ieee80211_rx(_irqsafe)). Each driver can now be
optimised on its own schedule.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Added support for the Broadcom 4318E chipset on PCMCIA/CF cards. The
4318E can do 802.11A/B/G, only B and G mode are supported in b43.
Signed-off-by: Clyde McPherson <ccmcphe@verizon.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Fix condition in which radio LED did not initialize correctly, and remove
4 compilation warnings.
After the recent changes in rfkill, the radio LED used by b43/b43legacy
did not always initialize correctly.
Both b43 and b43legacy used the deprecated variable radio_enabled in
struct ieee80211_conf.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add automagic feature flags, so the firmware can tell the driver
about supported features and the driver can switch features on/off as
needed.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This ports the b43/legacy rfkill code to the new API offered
by cfg80211 and thus removes a lot of useless stuff.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Fix possible unaligned u32 access in b43_generate_plcp_hdr().
Unaligned data is read/write with a u32 pointer instead of using the
packed structure. Some versions of gcc ignore the "packed" attribute, if the
structure element is accessed through a local pointer.
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch completely rewrites the rfkill core to address
the following deficiencies:
* all rfkill drivers need to implement polling where necessary
rather than having one central implementation
* updating the rfkill state cannot be done from arbitrary
contexts, forcing drivers to use schedule_work and requiring
lots of code
* rfkill drivers need to keep track of soft/hard blocked
internally -- the core should do this
* the rfkill API has many unexpected quirks, for example being
asymmetric wrt. alloc/free and register/unregister
* rfkill can call back into a driver from within a function the
driver called -- this is prone to deadlocks and generally
should be avoided
* rfkill-input pointlessly is a separate module
* drivers need to #ifdef rfkill functions (unless they want to
depend on or select RFKILL) -- rfkill should provide inlines
that do nothing if it isn't compiled in
* the rfkill structure is not opaque -- drivers need to initialise
it correctly (lots of sanity checking code required) -- instead
force drivers to pass the right variables to rfkill_alloc()
* the documentation is hard to read because it always assumes the
reader is completely clueless and contains way TOO MANY CAPS
* the rfkill code needlessly uses a lot of locks and atomic
operations in locked sections
* fix LED trigger to actually change the LED when the radio state
changes -- this wasn't done before
Tested-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> [thinkpad]
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
