| Age | Commit message (Collapse) | Author |
|---|
|
Remove the support for all the PCI_IDs never make into production
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Different channel has different configuration, need to pass correct
configuration to uCode when send "channel switch" command to uCode.
Invalid configuration will cause sysassert in uCode and produce
un-expected result.
Even it is a very small windows, but we also need to consider and handle
the case if commit_rxon occurred before the "channel switch
announcement" notification received from uCode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Remove un-used parameter "recovery_rxon" from "priv" data structure
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When I added that code setting the swq_id, I evidently
did not understand the distinction between FIFO and TX
queue yet and added code to compare a queue ID and a
FIFO number, which is bogus.
However, the code there need not be this specific, it
can just set all queues to the identity mapping which
will be overwritten by the aggregation queue code. As
a bit of defensive coding, don't assign an swq_id to
the command queue so that if we ever use it for frames
we notice quickly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Spatial Multiplexing Power Save was disabled to achieve better
throughput while in power save mode by activating all the rx chains all the time.
By doing so, the device power consumption is high.
Enable static/dynamic spatial multiplexing power save if device support
it, which can lower the power consumption without impact throughput.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
RX_FREE_BUFFERS and RX_LOW_WATERMARK are currently defined in four places.
Based on how files are included we only need the definition in iwl-fh.h
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reported-by: Frans Pop <elendil@planet.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Increase the size of TFD_MAX_PAYLOAD_SIZE (the size of iwl_device_cmd)
to accommodate iwl6000_channel_switch_cmd data structure.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Acked-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Consolidate most iwlXXXX_apm_init() functions into single iwl_apm_init().
Keep iwl3945_apm_init(), but leverage iwl_apm_init() for most functionality.
Update 4965 init sequence to follow most recent factory recommendations.
Add following members to struct iwl_cfg to guide the init sequence:
pll_cfg_val (replaces needs_pll_cfg), set_l0s, use_bsm
Move L0S enable/disable from nic_config() functions to iwl_apm_init().
This satisifies the "FIXME: put here L1A -L0S w/a" notice, and complies
with factory-recommended sequence.
Add debug info message in iwl_apm_init(), and symmetrical message
in iwl_apm_stop().
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Currently mac80211 initializes the rate scaling before notifying the driver
of the station's existence. The driver dealt with this by not relying on
mac80211's station notifications and instead mixing this functionality with
the rate scaling code and other places. To clean this up the driver needs
to do rate scaling initialization after being notified of the station, this
can be done if the rate scaling information forms part of the station
information passed from mac80211 to driver.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This switches the iwlwifi driver to use paged skb from linear skb for Rx
buffer. So that it relieves some Rx buffer allocation pressure for the
memory subsystem. Currently iwlwifi (4K for 3945) requests 8K bytes for
Rx buffer. Due to the trailing skb_shared_info in the skb->data,
alloc_skb() will do the next order allocation, which is 16K bytes. This
is suboptimal and more likely to fail when the system is under memory
usage pressure. Switching to paged Rx skb lets us allocate the RXB
directly by alloc_pages(), so that only order 1 allocation is required.
It also adjusts the area spin_lock (with IRQ disabled) protected in the
tasklet because tasklet guarentees to run only on one CPU and the new
unprotected code can be preempted by the IRQ handler. This saves us from
spawning another workqueue to make skb_linearize/__pskb_pull_tail happy
(which cannot be called in hard irq context).
Finally, mac80211 doesn't support paged Rx yet. So we linearize the skb
for all the management frames and software decryption or defragmentation
required data frames before handed to mac80211. For all the other frames,
we __pskb_pull_tail 64 bytes in the linear area of the skb for mac80211
to handle them properly.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Remove the ununsed variable data_retry_limit
from priv.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Adding accumulative statistics counters in iwlwifi driver.
Statistics counters are reported by uCode every beacon interval; but can
be reset by uCode when needed. The accumulative statistics counters is
maintained by driver to keep track of the history of all the counters.
Update the ucode stats files in debugfs to display both latest and
accumulative counters.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Instead of always allocate the max number of tx queue structure,
use dynamic allocation based on the number of queues in device
configuration. With these changes, device does not have to allocate more
memory than the h/w can support.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add more items to sensitivity range table to avoid using hardcoded values.
Initialize the table per device since unique per device information is
required to perform sensitivity calibration.
additional items in sensitivity range table:
.barker_corr_th_min: Barker correlation threshold minimum
.barker_corr_th_min_mrc: Barker correlation threshold minimum for MRC
.nrg_th_cca: Energy threshold for Clear Channel Assessment
Barker codes are a technique used in WLAN encoding for transmission.
MRC is "Maximal Ratio Combining", a technique for optimally combining the
signals from 2 or more receivers to achieve a better signal.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
"IWL_CMD_QUEUE_NUM" is being defined in multiple places and used by all
the devices. move it to iwl-dev.h file and shared by all the devices.
Remove "IWL_CMD_FIFO_NUM", replaced by "IWL49_CMD_FIFO_NUM" and IWL50_CMD_FIFO_NUM"
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Clean up device-specific apm_reset() functions and library infrastructure,
now that these reset() functions are no longer being used.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Unify the usage of apm_stop_master and apm_stop
across all hardwares.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The iwlwifi drivers have LED blinking requirements that
mac80211 cannot fulfill due to the use of just a single
LED instead of different ones for TX, RX, radio etc.
Instead, the single LED blinks according to transfers
and is solid on the rest of the time. As such, having
LED class devices registered that mac80211 triggers are
connected to is pointless as we don't use the triggers
anyway.
Remove all the useless code and add hooks into the
driver itself. At the same time, make the LED code
abstracted so the core code that determines blink rate
etc. can be shared between 3945 and agn in iwlcore.
At the same time, the fact that we removed the use of
the mac80211 LED triggers means we can also remove the
IWLWIFI_LEDS Kconfig symbol since the LED support is
now self-contained.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Adding support of Chain Noise Calibration for 6000 series NICs.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Update PCI Subsystem ID for 60x0 series based on HW SKU. Adding new SKU
for "ABG" and "BG" only devices.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Update PCI Subsystem ID for 1000 series based on HW SKU. Adding new SKU
for "BG" only devices.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The chain settings we currently use in iwlwifi are
rather confusing -- and we also go by the wrong
settings entirely under certain circumstances. To
clean it up, create a new variable in the current
HT config -- single_chain_sufficient -- that tells
us whether we need more than one chain. Calculate
that based on the AP and operating mode (no IBSS
HT implemented -- so no need for multiple chains,
for station mode we use the AP's capabilities).
Additionally, since APs always send disabled SM PS
mode, keeping track of their sm_ps mode isn't very
useful -- doubly not so for our _own_ RX config
since that should depend on our, not the AP's, SM
PS mode.
Finally, document that our configuration of the
number of RX chains used is currently wrong when
in powersave (by adding a comment).
All together this removes the two remaining items
in struct iwl_ht_config that were done wrong there.
For the future, the number of RX chains and some
SM PS handshaking needs to be added to mac80211,
which then needs to tell us, and the new variable
current_ht_config.single_chain_sufficient should
also be calculated by mac80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Daniel Halperin pointed out that the naming
here is rather inconsistent with at least 3
different names being used for one thing in
different contexts. Rename the struct to
iwl_ht_config (rather than iwl_ht_info) and
use ht_conf as a variable for it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
is_ht can be bool instead of u8, and there's
no need to use IWL_CHANNEL_WIDTH_* constants
in supported_chan_width when that could just
be named is_40mhz instead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The ICT IRQ table is a set of __le32 values, not u32 values,
so when reading it we need to take into account that it has
to be converted to CPU endianness. This was causing a lot of
trouble on my powerpc box where various things would simply
not work for no apparent reason with 5xxx cards, but worked
with 4965 -- which doesn't use the ICT table.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Changing the name from "tx_power_channel_lmt" to "tx_power_device_lmt";
to give idea that scope of limit is for overall device, not any
individual channels
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Green-field mode should be configured in the HT station table. This patch uses
both the per-station GF support flag as well as the current BSS HT operation
mode (non-GF stations present flag).
Added the "ht_greenfield_support" field to struct iwl_cfg to replace the
device-specific check in rs_use_green(). That check has been moved to
iwlcore_init_ht_hw_capab().
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Short guard interval support is a local per-station parameter not a global
per-NIC parameter. (mac80211 will correctly remove SGI support from station
capabilities if the BSS does not permit it). This patch removes the short GI
support bitfield from the global iwl_ht_info struct and properly uses
per-station HT capabilities during rate selection.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Some members of iwl_ht_info are unused, and one of
them is write-only, so we can remove these three:
max_amsdu_size, ampdu_factor and mpdu_density.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
For devices using OTP memory, EEPROM image can start from
any one of the OTP blocks. If shadow RAM is disabled, we need to
traverse link list to find the last valid block, then start the EEPROM
image reading.
If OTP is not full, the valid block is the block _before_ the last block
on the link list; the last block on the link list is the empty block
ready for next OTP refresh/update.
If OTP is full, then the last block is the valid block to be used for
configure the device.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The tx_chan_width entry is never used, supported_chan_width is used instead.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Depending on required latency requested by pm_qos (via mac80211)
we can automatically adjust the sleep state. Also, mac80211 has
a user-visible dynamic sleep feature where we are supposed to
stay awake after sending/receiving frames to better receive
response frames to our packets, this can be integrated into the
sleep command.
Currently, and this patch doesn't change that yet, we default
to using sleep level 1 if PS is enabled. With a module parameter
to iwlcore, automatic adjustment to changing network latency
requirements can be enabled -- this isn't yet the default due
to requiring more testing.
The goal is to enable automatic adjustment and then go into the
deepest possible sleep state possible depending on the networking
latency requirements.
This patch does, however, enable IEEE80211_HW_SUPPORTS_DYNAMIC_PS
to avoid the double-timer (one in software and one in the device)
when transmitting -- the exact timeout may be ignored but that is
not of big concern.
Note also that we keep the hard-coded power indices around for
thermal throttling -- the specification of that calls for using
the specified power levels. Those can also be selected in debugfs
to allow easier testing of such parameters.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Some of the thermal throttle data structures and code
are really very intermingled with the sleep (power)
control code. They really do belong together in a way
since the thermal throttle code uses powersaving to
achieve its goal, but it's making it hard to work on
the powersave code. Split this up to make that easier.
I've also changed the antenna defines to an enum and
used the same enum for RX and TX.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Move all the thermal throttling functions to background task to make
sure do not change power and rx chain in interrupt handler.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
commit "iwlwifi: uCode Alive notification with timeout" introduced a more
reliable mechanism for ucode loading. Unfortunately we hit a problem with
it frequently enough to make a 4965 unusable. The problem can be seen in
debug log below. What this code attempts is to set runtime ucode up to
load, start a timer to wait for the alive response from runtime ucode, and
if it times out it tries again. As can be seen below we receive the alive
response and wake the waiting task _before_ the tasks starts waiting. The
task thus times out as the alive response is not received while it is
waiting for it and it restarts the device. This starts the cycle all over
again.
[29739.000819] ieee80211 phy0: U iwl_mac_start enter
[29739.005751] ieee80211 phy0: U iwl_prepare_card_hw iwl_prepare_card_hw enter
[29739.012798] ieee80211 phy0: U iwl_set_hw_ready hardware ready
[29739.057200] ieee80211 phy0: U iwl4965_load_bsm Begin load bsm
[29739.063366] ieee80211 phy0: U iwl4965_verify_bsm Begin verify bsm
[29739.072485] ieee80211 phy0: U iwl4965_verify_bsm BSM bootstrap uCode image OK
[29739.079671] ieee80211 phy0: U iwl4965_load_bsm BSM write complete, poll 0 iterations
[29739.257019] ieee80211 phy0: I iwl_rx_reply_alive Alive ucode status 0x00000001 revision 0x1 0x9
[29739.260964] ieee80211 phy0: I iwl_rx_reply_alive Initialization Alive received.
[29739.260964] ieee80211 phy0: U __iwl_up iwlagn is coming up
[29739.278571] ieee80211 phy0: U iwl_mac_start Start UP work done.
[29739.284509] ieee80211 phy0: U iwlcore_verify_inst_sparse ucode inst image size is 788
[29739.292432] ieee80211 phy0: U iwlcore_verify_inst_sparse ucode inst image size is 10312
[29739.302004] ieee80211 phy0: U iwl_verify_ucode Initialize uCode is good in inst SRAM
[29739.309746] ieee80211 phy0: U iwl4965_hw_get_temperature Running temperature calibration
[29739.317833] ieee80211 phy0: U iwl4965_hw_get_temperature Calib values R[1-3]: -36 13522 -13496 R4: -2726
[29739.327337] ieee80211 phy0: U iwl4965_hw_get_temperature Calibrated temperature: 310K, 37C
[29739.335598] ieee80211 phy0: U iwl4965_init_alive_start Initialization Alive received.
[29739.343477] ieee80211 phy0: U iwl4965_set_ucode_ptrs Runtime uCode pointers are set.
[29739.351283] ieee80211 phy0: I iwl_rx_reply_alive Alive ucode status 0x00000001 revision 0x1 0x0
[29739.355210] ieee80211 phy0: I iwl_rx_reply_alive Runtime Alive received.
[29739.366731] iwlagn 0000:03:00.0: Runtime uCode already alive? Waiting for alive anyway
[29743.284110] iwlagn 0000:03:00.0: START_ALIVE timeout after 4000ms.
[29743.290337] ieee80211 phy0: U iwl_mac_add_interface enter: type 2
[29744.364089] iwlagn 0000:03:00.0: Runtime timeout after 5000ms
[29744.370882] ieee80211 phy0: U iwl_alive_start Runtime Alive received.
[29744.377347] ieee80211 phy0: U iwlcore_verify_inst_sparse ucode inst image size is 788
[29744.385287] ieee80211 phy0: U iwlcore_verify_inst_sparse ucode inst image size is 10312
[29744.393397] ieee80211 phy0: U iwlcore_verify_inst_sparse ucode inst image size is 94720
[29744.415835] ieee80211 phy0: U iwl_verify_ucode Runtime uCode is good in inst SRAM
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Break down the traffic type and counter for both Tx and Rx.
Enhance the tx_statistics and rx_statistics debugfs function and move
to /sys/kernel/debug/ieee80211/phy0/iwlagn/debug directory to help
better debugging both driver and uCode related problems.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The traffic buffer will only beallocated and used if either bit 23
(IWL_DX_TX) or bit 24 (IWL_DL_RX) of "debug" is set;
example: "debug=0x800000" - log tx data traffic
"debug=0x1000000" - log rx data traffic
"debug=0x1800000" - log both tx and rx traffic
The traffic log will store the beginning portion (64 bytes) of the
latest 256 of tx and rx packets in the round-robbin buffer for
debugging,
user can examine the log through debugfs file.
How to display the current logged tx/rx traffic and txfifo and rxfifo
read/write point:
"cat traffic_log" in /sys/kernel/debug/ieee80211/phy0/iwlagn/debug
directory
By echo "0" to traffic_log file will empty the traffic log buffer and
reset both tx and rx taffic log index to 0.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Rename "fat" to "ht40"
The term "fat channel" is deprecated in favor of "HT40"
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Commit "iwlwifi: make debug level more user friendly" cleaned up the
debug level handling. In doing so it created a single global debug
level for all devices. Some setups do consits of more that one iwlwifi
device and in these setups there is a requirement that debug levels
should be unique per device.
We now re-introduce the per device debugging while maintaining the
cleanup effort of the previous patch.
The maintain the global debug level and now introduce a per-device debug
level that will be used if it (the per-device debug level) is set. The
per-device debug level can be controlled via the debug_level sysfs file
while the global debug level is controlled by the debug module parameter.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Remove the support for deprecated devices. These devices are
engineering samples and no longer supported by the uCode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
For 6x00 2x2 NIC, two types of Power Amplifier are available.
In order for uCode to apply correct tx power,
driver needs to program the CSR_GP_DRIVER_REG register and
let uCode know the type of PA.
If driver do not program CSR_GP_DRIVER_REG register (default to 0),
then it is uCode's decision for tx power
2x2 Hybrid card: use both internal and external PA
2x2 IPA(Internal Power Amplifier) card: internal PA only
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add debugfs file to enable/disable HT40(40MHz) channel support.
By default, 40MHz is supported if AP can support the function.
By echo "1" to "disable_ht40" file, iwlwifi driver will disable the
40MHz support and only allow 20MHz channel.
Because the information exchange happen during association time,
so enable/disable ht40 channel only can be performed when it is not
associated with AP.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Fix incorrect name for HT MPDU Density.
default set to 4 uSec
Reported-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
No existing callbacks use anything other than the return
value 1, which means that the caller should free the
reply skb, so it seems safer in terms of not introducing
memory leaks to simply remove the return value and let
the caller always free the skb.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The current command sending in iwlwifi is a bit of a mess:
1) there is a struct, iwl_cmd, that contains both driver
and device data in a single packed structure -- this
is very confusing
2) the on-stack data and the command metadata share a
structure by embedding the latter in the former, which
is also rather confusing because it leads to weird
unions and similarly odd constructs
3) each txq always has enough space for 256 commands,
even if only 32 end up being used
This patch fixes these things:
1) rename iwl_cmd to iwl_device_cmd and keep track of
command metadata and device command separately, in
two arrays in each tx queue
2) remove the 'meta' member from iwl_host_cmd and only
put in the required members
3) allocate the cmd/meta arrays separately instead of
embedding them into the txq structure
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
If advance thermal throttling is used the driver need to pass both
"enter" and "exit" temperature to uCode.
Using different critical temperature threshold for legacy and advance
thermal throttling management based on the type of thermal throttling
method is used except 1000.
For 1000, it use advance thermal throttling critical temperature
threshold, but with legacy thermal management implementation until ucode
has the necessary implementations in place.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
* Deprecate the "debug50" module parameter used to obtain
5000 series and up debugging. Replace it with "debug" module
parameter to match with original driver and be consistent
between them. The "debug50" module parameter can still be used,
except that the module parameter is not writable in keeping
with its previous state. We currently just mark it as "deprecated"
and do not have it in the feature-removal-schedule. Some more
cleanup of module parameters needs to be done and can then be
entered together.
* Only make "debug" module parameters visible if the driver
is compiled with CONFIG_IWLWIFI_DEBUG. This will eliminate
a lot of confusion where users think they have set debug flags
but yet cannot see any debug output.
* Make module parameters writable. This eliminates the need for the
"debug_level" sysfs file, which can now also be deprecated and
added to feature-removal-schedule. This file is in significant
use though with many iwlwifi documents and text referring users
to it. We can thus not take its removal lightly and keep it around.
With iwlcore shared between iwlagn and iwl3945 we really do not need
debug module parameters for each but can instead have one debug
module parameter for the iwlcore module. The same issue is here as
with the sysfs file - a lot of iwlwifi documentation and text (like
bug reports) rely on iwlagn and iwl3945 having this module parameter,
so changing this to a module parameter of iwlcore will have significant
impact and we do not do this for that reason.
One consequence of this patch is that if a user is running a system
with both 3945 and later hardware then the setting of the one module
parameter will affect the value of the other. The likelihood of this
seems low - and even if this setup is present it does not seem like an
issue for both modules to run with the same debug level.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Wait for REPLY_ALIVE notification from init and runtime uCode.
based on the type of REPLY_ALIVE, different status bit will be set to
wake up the queue:
STATUS_INIT_UCODE_ALIVE for init uCode
STATUS_RT_UCODE_ALIVE for runtime uCode.
If timeout, attempt to download the failing uCode image again. This can
only be done for the init ucode images of all iwlagn devices and the
runtime ucode image of the 5000 series and up. If there is a problem
with the 4965 runtime ucode coming up we restart the interface and thus
trigger a new download of the init ucode also.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Adding new API version to account for change to ucode file format. New
header includes the build number of the ucode. This build number is the
SVN revision thus allowing for exact correlation to the code that
generated it.
The header adds the build number so that older ucode images can also be
enhanced to include the build in the future.
some cleanup in iwl_read_ucode needed to ensure old header not used and
reduce unnecessary references through pointer with the data is already
in heap variable.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We need to provide a reasonable minimum that will result in a
working setup if used. Set minimum to be 10 to provide for
4 standard TX queues + 1 command queue + 2 (unused) HCCA queues +
4 HT queues (one per AC).
We allow the user to change the number of queues used via a module
parameter and use this minimum value to check if it is valid. Without
this patch a user can select a value for the number of queues that
will result in a failing setup.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
