aboutsummaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)Author
2009-10-08Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (40 commits) ethoc: limit the number of buffers to 128 ethoc: use system memory as buffer ethoc: align received packet to make IP header at word boundary ethoc: fix buffer address mapping ethoc: fix typo to compute number of tx descriptors au1000_eth: Duplicate test of RX_OVERLEN bit in update_rx_stats() netxen: Fix Unlikely(x) > y pasemi_mac: ethtool get settings fix add maintainer for network drop monitor kernel service tg3: Fix phylib locking strategy rndis_host: support ETHTOOL_GPERMADDR ipv4: arp_notify address list bug gigaset: add kerneldoc comments gigaset: correct debugging output selection gigaset: improve error recovery gigaset: fix device ERROR response handling gigaset: announce if built with debugging gigaset: handle isoc frame errors more gracefully gigaset: linearize skb gigaset: fix reject/hangup handling ...
2009-10-07ethoc: limit the number of buffers to 128Thomas Chou
Only 128 buffer descriptors are supported in the core. Limit the number in case we have more memory. Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-07ethoc: use system memory as bufferThomas Chou
This patch enabled the ethoc to allocate system memory as buffer when there is no dedicated buffer memory. Some hardware designs may not have dedicated buffer memory such as on chip or off chip SRAM. In this case, only one memory resource is supplied in the platform data instead of two. Then a DMA buffer can be allocated from system memory and used for the transfer. Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-07ethoc: align received packet to make IP header at word boundaryThomas Chou
The packet buffer is allocated at 4 bytes boundary, but the IP header length and version bits is located at byte 14. These bit fields access as 32 bits word and caused exception on processors that do not support unaligned access. The patch adds 2 bytes offset to make the bit fields word aligned. Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-07ethoc: fix buffer address mappingThomas Chou
The pointer address in buffer descriptors is physical address. The pointer that processor used to access packet is virtual address. Though the higher bits of pointer address used by the MAC may be truncated to zero in special case, it is not always true in larger designs. Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-07ethoc: fix typo to compute number of tx descriptorsThomas Chou
It should be max() instead of min(). Use 1/4 of available descriptors for tx, and there should be at least 2 tx descriptors. Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-07au1000_eth: Duplicate test of RX_OVERLEN bit in update_rx_stats()roel kluin
in update_rx_stats() the RX_OVERLEN bit is set twice, replace it by RX_RUNT. in au1000_rx() the RX_MISSED_FRAME bit was tested a few lines earlier already Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Acked-by: Manuel Lauss <manuel.lauss@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-07netxen: Fix Unlikely(x) > yRoel Kluin
The closing parenthesis was not on the right location. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Acked-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-07pasemi_mac: ethtool get settings fixValentine Barshak
Not all pasemi mac interfaces can have a phy attached. For example, XAUI has no phy and phydev is NULL for it. In this case ethtool get settings causes kernel crash. Fix it by returning -EOPNOTSUPP if there's no PHY attached. Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com> Acked-by: Olof Johansson <olof@lixom.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-07tg3: Fix phylib locking strategyMatt Carlson
Felix Radensky noted that chip resets were generating stack trace dumps. This is because the driver is attempting to acquire the mdio bus mutex while holding the tp->lock spinlock. The fix is to change the code such that every phy access takes the tp->lock spinlock instead. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-07rndis_host: support ETHTOOL_GPERMADDRJohn W. Linville
Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06be2net: Bug fix to properly update ethtool tx-checksumming after ethtool -K ↵Ajit Khaparde
<ifname> tx off This is a fix for a bug which was a result of wrong use of checksum offload flag. The status of tx-checksumming was not changed from on to off after a 'ethtool -K <ifname> tx off' operation. Use the proper checksum offload flag NETIF_F_HW_CSUM instead of NETIF_F_IP_CSUM and NETIF_F_IPV6_CSUM. Patch is against net-2.6 tree. Signed-off-by: Ajit Khaparde <ajitk@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06be2net: Fix a typo in be_cmds.hAjit Khaparde
MCC_STATUS_NOT_SUPPORTED should be decimal 66 not hex 66. This patch fixes this typo. Patch against net-2.6 tree. Signed-off-by: Ajit Khaparde <ajitk@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06be2net: Bug Fix while accounting of multicast frames during netdev stats updateAjit Khaparde
While updating the statistics to be passed via the get_stats, tx multicast frames were being accounted instead of rx multicast frames. This patch fixes the bug. This patch is against the net-2.6 tree. Signed-off-by: Ajit Khaparde <ajitk@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06qlge: Fix lock/mutex warnings.Ron Mercer
Get rid of spinlock and private mutex usage for exclusive access to the HW semaphore register. rtnl_lock already creates exclusive access to this register in all driver API. Add rtnl to firmware worker threads that also use the HW semaphore register. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06qlge: Fix queueing of firmware handler in ISR.Ron Mercer
Check that we are not already polling firmware events before we queue the firmware event worker, then disable firmware interrupts. Otherwise we can queue the same event multiple times. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06qlge: Fix some bit definitions for reset register.Ron Mercer
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-05be2net: Fix a bug in preparation of mcc wrb which was causing flash ↵Ajit Khaparde
operation to fail This patch fixes a bug that got introduced in commit 76998bc7. During preparation of mcc wrb, req was being wrongly overwritten and the flash operation was failing. Signed-off-by: Ajit Khaparde <ajitk@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-05pcnet_cs: add cis of National Semicondoctor's multifunction pcmcia cardKen Kawasaki
pcnet_cs,serial_cs: add cis of National Semicondoctor's lan&modem mulitifunction pcmcia card, NE2K, tamarack ethernet card, and some serial card(COMpad2, COMpad4). Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-04e1000e: swap max hw supported frame size between 82574 and 82583Alexander Duyck
There appears to have been a mixup in the max supported jumbo frame size between 82574 and 82583 which ended up disabling jumbo frames on the 82574 as a result. This patch swaps the two so that this issue is resolved. This patch fixes http://bugzilla.kernel.org/show_bug.cgi?id=14261 Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-04ixgbe: add support for 82599 based X520 10G Dual KX4 Mezz cardDon Skidmore
This patch adds device support for the 82599 based X520 10GbE Dual Port KX4 Mezzanine card. Signed-off-by: Don Skidmore<donald.c.skidmore@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-04ixgbe: add support for 82599 Combined BackplaneDon Skidmore
This patch will add support for the 82599 Dual port Backplane device (0x10f8). This device has the ability to link in serial (KR) and parallel (KX4/KX) modes, depending on what the switch capabilities are in the blade chassis. Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-02Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (46 commits) cnic: Fix NETDEV_UP event processing. uvesafb/connector: Disallow unpliviged users to send netlink packets pohmelfs/connector: Disallow unpliviged users to configure pohmelfs dst/connector: Disallow unpliviged users to configure dst dm/connector: Only process connector packages from privileged processes connector: Removed the destruct_data callback since it is always kfree_skb() connector/dm: Fixed a compilation warning connector: Provide the sender's credentials to the callback connector: Keep the skb in cn_callback_data e1000e/igb/ixgbe: Don't report an error if devices don't support AER net: Fix wrong sizeof net: splice() from tcp to pipe should take into account O_NONBLOCK net: Use sk_mark for routing lookup in more places sky2: irqname based on pci address skge: use unique IRQ name IPv4 TCP fails to send window scale option when window scale is zero net/ipv4/tcp.c: fix min() type mismatch warning Kconfig: STRIP: Remove stale bits of STRIP help text NET: mkiss: Fix typo tg3: Remove prev_vlan_tag from struct tx_ring_info ...
2009-10-02cnic: Fix NETDEV_UP event processing.Michael Chan
This fixes the problem of not handling the NETDEV_UP event properly during hot-plug or modprobe of bnx2 after cnic. The handling was skipped by mistakenly using "else if" to check for the event. Also update version to 2.0.1. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-02e1000e/igb/ixgbe: Don't report an error if devices don't support AERFrans Pop
The only error returned by pci_{en,dis}able_pcie_error_reporting() is -EIO which simply means that Advanced Error Reporting is not supported. There is no need to report that, so remove the error check from e1000e, igb and ixgbe. Signed-off-by: Frans Pop <elendil@planet.nl> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-02net: Fix wrong sizeofJean Delvare
Which is why I have always preferred sizeof(struct foo) over sizeof(var). Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-01sky2: irqname based on pci addressStephen Hemminger
This is based on Michal Schmidt fix for skge. Most network drivers request their IRQ when the interface is activated. sky2 does it in ->probe() instead, because it can work with two-port cards where the two net_devices use the same IRQ. This works fine most of the time, except in some situations when the interface gets renamed. Consider this example: 1. modprobe sky2 The card is detected as eth0 and requests IRQ 17. Directory /proc/irq/17/eth0 is created. 2. There is an udev rule which says this interface should be called eth1, so udev renames eth0 -> eth1. 3. modprobe 8139too The Realtek card is detected as eth0. It will be using IRQ 17 too. 4. ip link set eth0 up Now 8139too requests IRQ 17. The result is: WARNING: at fs/proc/generic.c:590 proc_register ... proc_dir_entry '17/eth0' already registered The fix is for sky2 to name the irq based on the pci device, as is done by some other devices DRM, infiniband, ... ie. sky2@pci:0000:00:00 Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Reviewed-by: Michal Schmidt <mschmidt@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-01skge: use unique IRQ nameMichal Schmidt
Most network drivers request their IRQ when the interface is activated. skge does it in ->probe() instead, because it can work with two-port cards where the two net_devices use the same IRQ. This works fine most of the time, except in some situations when the interface gets renamed. Consider this example: 1. modprobe skge The card is detected as eth0 and requests IRQ 17. Directory /proc/irq/17/eth0 is created. 2. There is an udev rule which says this interface should be called eth1, so udev renames eth0 -> eth1. 3. modprobe 8139too The Realtek card is detected as eth0. It will be using IRQ 17 too. 4. ip link set eth0 up Now 8139too requests IRQ 17. The result is: WARNING: at fs/proc/generic.c:590 proc_register ... proc_dir_entry '17/eth0' already registered ... And "ls /proc/irq/17" shows two subdirectories, both called eth0. Fix it by using a unique name for skge's IRQ, based on the PCI address. The naming from the example then looks like this: $ grep skge /proc/interrupts 17: 169 IO-APIC-fasteoi skge@pci:0000:00:0a.0, eth0 irqbalance daemon will have to be taught to recognize "skge@" as an Ethernet interrupt. This will be a one-liner addition in classify.c. I will send a patch to irqbalance if this change is accepted. Signed-off-by: Michal Schmidt <mschmidt@redhat.com> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-01Kconfig: STRIP: Remove stale bits of STRIP help textRalf Baechle
Remove references to dead web site mosquitonet.Stanford.EDU. Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-01NET: mkiss: Fix typoRalf Baechle
This typo was introduced by 5793f4be23f0171b4999ca68a39a9157b44139f3 on October 14, 2005 ... Reported-by: Matti Aarnio <matti.aarnio@zmailer.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-01tg3: Remove prev_vlan_tag from struct tx_ring_infoEric Dumazet
prev_vlan_tag field is not used. Patch saves 512*8 bytes per tx queue ring on 64bit arches. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Matthew Carlson <mcarlson@broadcom.com>
2009-10-01move virtnet_remove to .devexit.textUwe Kleine-König
The function virtnet_remove is used only wrapped by __devexit_p so define it using __devexit. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Sam Ravnborg <sam@ravnborg.org> Cc: David S. Miller <davem@davemloft.net> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Alex Williamson <alex.williamson@hp.com> Cc: Mark McLoughlin <markmc@redhat.com> Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-01don't use __devexit_p to wrap sgiseeq_removeUwe Kleine-König
The function sgiseeq_remove is defined using __exit, so don't use __devexit_p but __exit_p to wrap it. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Cc: David S. Miller <davem@davemloft.net> Cc: Wang Chen <wangchen@cn.fujitsu.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Patrick McHardy <kaber@trash.net> Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-01don't use __devexit_p to wrap meth_removeUwe Kleine-König
The function meth_remove is defined using __exit, so don't use __devexit_p but __exit_p to wrap it. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Cc: David S. Miller <davem@davemloft.net> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Patrick McHardy <kaber@trash.net> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-01bonding: set primary param via sysfsJiri Pirko
Primary module parameter passed to bonding is pernament. That means if you release the primary slave and enslave it again, it becomes the primary slave again. But if you set primary slave via sysfs, the primary slave is only set once and it's not remembered in bond->params structure. Therefore the setting is lost after releasing the primary slave. This simple one-liner fixes this. Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-01Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
2009-10-01ixgbe: correct the parameter descriptionJiri Pirko
ccffad25b5136958d4769ed6de5e87992dd9c65c changed parameters for function ixgbe_update_uc_addr_list_generic but parameter description was not updated. This patch corrects it. Signed-off-by: Jiri Pirko <jpirko@redhat.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-30be2net: Workaround to fix a bug in Rx Completion processing.Ajit Khaparde
vtp bit in RX completion descriptor could be wrongly set in some skews of BladEngine. Ignore this bit if vtm is not set. Resending because the previous patch was against net-next tree. This patch is against the net-2.6 tree. Signed-off-by: Ajit Khaparde <ajitk@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-303c59x: Rework suspend and resumeAnton Vorontsov
As noticed by Alan Stern, there is still one issue with the driver: we disable PCI IRQ on suspend, but other devices on the same IRQ line might still need the IRQ enabled to suspend properly. Nowadays, PCI core handles all power management work by itself, with one condition though: if we use dev_pm_ops. So, rework the driver to only quiesce 3c59x internal logic on suspend, while PCI core will manage PCI device power state with IRQs disabled. Suggested-by: Rafael J. Wysocki <rjw@sisk.pl> Suggested-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Acked-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-30drivers/net: ks8851_mll ethernet network driverChoi, David
This is the first registration of ks8851 network driver with MLL(address/data multiplexed) interface. Signed-off-by : David J. Choi <david.choi@micrel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-30skge: Make sure both ports initialize correctlyMike McCormack
If allocation of the second ports fails, make sure that hw->ports is not 2 otherwise we'll crash trying to access the second port. This fix is copied from a similar fix in the sky2 driver (ca519274...), but is untested, as I don't have a skge card. Signed-off-by: Mike McCormack <mikem@ring3k.org> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-30bcm63xx_enet: timeout off by one in do_mdio_op()roel kluin
`while (limit-- >= 0)' reaches -2 after the loop upon timeout. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Acked-by: Maxime Bizon <mbizon@freebox.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-30qlge: Fix error exit for probe call.Ron Mercer
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-30qlge: Protect reset recovery with rtnl_lock().Ron Mercer
Move the call to rtnl_lock() to before the internal call to ql_adapter_down()/ql_adapter_up(). This prevents collisions that can happen when recovering from an asic error. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-30qlge: Fix spin_lock warning.Ron Mercer
Remove the unnecessary locking around the call to ql_adapter_reset(). Sep 25 08:17:29 localhost kernel: SOFTIRQ-ON-W at: Sep 25 08:17:29 localhost kernel: [<c0000000000a2964>] .lock_acquire+0x10c/0x158 Sep 25 08:17:29 localhost kernel: [<c0000000004542e0>] ._spin_lock+0x34/0x58 Sep 25 08:17:29 localhost kernel: [<d000000006723070>] .ql_adapter_down+0x40c/0x4a0 [qlge] Sep 25 08:17:29 localhost kernel: [<d0000000067256d8>] .qlge_close+0x38/0x58 [qlge] Sep 25 08:17:29 localhost kernel: [<c0000000003ada6c>] .dev_close+0xdc/0x118 Sep 25 08:17:29 localhost kernel: [<c0000000003adb48>] .rollback_registered+0xa0/0x158 Sep 25 08:17:29 localhost kernel: [<c0000000003adc50>] .unregister_netdevice+0x50/0x7c Sep 25 08:17:29 localhost kernel: [<c0000000003adca0>] .unregister_netdev+0x24/0x40 Sep 25 08:17:29 localhost kernel: [<d00000000672e0c0>] .qlge_remove+0x28/0x64 [qlge] Sep 25 08:17:29 localhost kernel: [<c000000000253fdc>] .pci_device_remove+0x50/0x90 Sep 25 08:17:29 localhost kernel: [<c0000000002f5434>] .__device_release_driver+0x94/0xf8 Sep 25 08:17:29 localhost kernel: [<c0000000002f5560>] .driver_detach+0xc8/0xfc Sep 25 08:17:29 localhost kernel: [<c0000000002f3fd8>] .bus_remove_driver+0xb4/0x114 Sep 25 08:17:29 localhost kernel: [<c0000000002f5d4c>] .driver_unregister+0x80/0xa4 Sep 25 08:17:29 localhost kernel: [<c00000000025421c>] .pci_unregister_driver+0x50/0xc8 Sep 25 08:17:29 localhost kernel: [<d00000000672e044>] .qlge_exit+0x1c/0x34 [qlge] Sep 25 08:17:29 localhost kernel: [<c0000000000ac8b0>] .SyS_delete_module+0x234/0x2d0 Sep 25 08:17:29 localhost kernel: [<c000000000008554>] syscall_exit+0x0/0x40 Sep 25 08:17:29 localhost kernel: INITIAL USE at: Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-30qlge: Fix out of sync hardware semaphore.Ron Mercer
ql_clear_routing_entries() takes/gives it's own hardware semaphore since it is called from more than one place. ql_route_initialize() should make this call and THEN take it's own semaphore before doing it's work. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-30qlge: Fix bad bit definitions.Ron Mercer
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-30ixgbe: Remove ATR computation for UDP trafficPeter P Waskiewicz Jr
ATR support for UDP on 82599 needs to be redesigned, since the current model doesn't make much sense. The fallout from having it in though is it causes all UDP traffic to still compute the ATR hashes on transmit, which are useless. This removal will return upwards of 10% of relative computational overhead in forwarding tests. Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-30ixgbe patch to provide NIC's tx/rx counters via ethtoolBen Greear
When LRO is enabled, the received packet and byte counters represent the LRO'd packets, not the packets/bytes on the wire. The Intel 82599 NIC has registers that keep count of the physical packets. Add these counters to the ethtool stats. The byte counters are 36-bit, but the high 4 bits were being ignored in the 2.6.31 ixgbe driver: Read those as well to allow longer time between polling the stats to detect wraps. Signed-off-by: Ben Greear <greearb@candelatech.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-30ixgbe: Bump driver version numberPeter P Waskiewicz Jr
A number of changes have gone in since the last version bump. Bump it to reflect the changes. Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-04 20:45:26 +0000