| Age | Commit message (Collapse) | Author |
|---|
|
When iwlan runs on IOMMU, IOMMU generates a lot of PTE write faults
because PTE write bit is not set on some of PTE's. This is because
iwlan driver calls DMA mapping with PCI_DMA_TODEVICE which is read only
in mapping PTE. But iwlan device actually writes to the mapped page to
update its contents. This issue is not exposed in swiotlb. But VT-d
hardware can capture this fault and stop the fault transaction.
The following patch fixes the issue.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Reviewed-by: Bhavesh Davda <bhavesh@vmware.com>
Tested-by: Chris Wright <chrisw@sous-sol.org>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
netns: fix double free at netns creation
veth : add the set_mac_address capability
sunlance: Beyond ARRAY_SIZE of ib->btx_ring
sungem: another error printed one too early
ISDN: fix sc/shmem printk format warning
SMSC: timeout reaches -1
smsc9420: handle magic field of ethtool_eeprom
sundance: missing parentheses?
smsc9420: fix another postfixed timeout
wimax/i2400m: driver loads firmware v1.4 instead of v1.3
vlan: Update skb->mac_header in __vlan_put_tag().
cxgb3: Add support for PCI ID 0x35.
tcp: remove obsoleted comment about different passes
TG3: &&/|| confusion
ATM: misplaced parentheses?
net/mv643xx: don't disable the mib timer too early and lock properly
net/mv643xx: use GFP_ATOMIC while atomic
atl1c: Atheros L1C Gigabit Ethernet driver
net: Kill skb_truesize_check(), it only catches false-positives.
net: forcedeth: Fix wake-on-lan regression
|
|
Fix lost set_mac_address capability.
Signed-off-by: Daniel Lezcano <daniel.lezcano@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Do not go beyond ARRAY_SIZE of ib->btx_ring
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Another error was printed one too early.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With a postfix decrement timeouts will reach -1 rather than 0, so
the error path does not appear.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ethtool.h says the driver should set the magic field in get_eeprom and
verify it in set_eeprom. This patch adds this functionality using an
arbitary driver-specific magic value constant (0x9420).
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Roel Kluin recently fixed several instances where variables reach -1,
but 0 is tested afterwards. This patch fixes another, so the timeout
will be correctly detected and a warning printed.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a one liner change to have the driver use by default the v1.4
of the i2400m firmware instead of v1.3. The v1.4 version of the
firmware has been submitted to David Woodhouse for inclusion in the
linux-firmware tree and it is already available at
http://linuxwimax.org/Download.
The reason for this change is that the 1.3 release of the user space
software and firmware has a few issues that will make it difficult to
use with currently deployed commercial networks such as Xohm and
Clearwire.
As well, the new 1.4 release of the user space software (which matches
the 1.4 firmware) has intermitent issues with the 1.3 firmware.
The 1.4 release in http://linuxwimax.org/Download has been widely
deployed and tested with the codebase in 2.6.29-rc, the 1.4 firmware
and the 1.4 user space components.
We understand it is quite late in the rc process for such a change,
but would like to ask for the change to be taken into consideration.
Alternatively, a user could always force feed a 1.4 firmware into a
driver that doesn't have this modification by:
$ cd /lib/firmware
$ mv i2400m-fw-usb-1.3.sbcf i2400m-fw-usb-1.3.real.sbcf
$ ln -sf i2400m-fw-usb-1.4.sbc i2400m-fw-usb-1.3.sbcf
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for adapters with a PCI id equal to 0x35.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
phyid Can't be both TG3_PHY_OUI_1 and TG3_PHY_OUI_2 and TG3_PHY_OUI_3.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mib_counters_update() also restarts the timer.
So the timer is dequeued, the stats are read and then the timer is
enqueued again. This is "okay" unless someone unloads the module.
The locking here is also broken:
mib_counters_update() grabs just a simple spinlock. The only thing the
lock is good for is to protect the timer func against other callers
namely mv643xx_eth_stop() && mv643xx_eth_get_ethtool_stats(). That means
if the spinlock is taken via the ethtool path and than the timer kicks
in then the box will lock up.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Acked-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dev_set_rx_mode() grabs netif_addr_lock_bh():
|BUG: sleeping function called from invalid context at /home/bigeasy/git/cryptodev-2.6/mm/slub.c:1599
|in_atomic(): 1, irqs_disabled(): 0, pid: 859, name: ifconfig
|2 locks held by ifconfig/859:
| #0: (rtnl_mutex){--..}, at: [<c0239ccc>] rtnl_lock+0x18/0x20
| #1: (_xmit_ETHER){-...}, at: [<c022d094>] dev_set_rx_mode+0x1c/0x30
|[<c029f118>] (dump_stack+0x0/0x14) from [<c003df28>] (__might_sleep+0x11c/0x13c)
|[<c003de0c>] (__might_sleep+0x0/0x13c) from [<c00a8854>] (kmem_cache_alloc+0x30/0xd4)
| r5:c78093a0 r4:c034a47c
|[<c00a8824>] (kmem_cache_alloc+0x0/0xd4) from [<c01a5fd0>] (mv643xx_eth_set_rx_mode+0x70/0x188)
|[<c01a5f60>] (mv643xx_eth_set_rx_mode+0x0/0x188) from [<c022ced0>] (__dev_set_rx_mode+0x40/0xac)
|[<c022ce90>] (__dev_set_rx_mode+0x0/0xac) from [<c022d09c>] (dev_set_rx_mode+0x24/0x30)
| r6:00001043 r5:c78090f8 r4:c7809000
|[<c022d078>] (dev_set_rx_mode+0x0/0x30) from [<c02304c4>] (dev_open+0xe4/0x114)
| r5:c7809350 r4:c7809000
|[<c02303e0>] (dev_open+0x0/0x114) from [<c022fd18>] (dev_change_flags+0xb0/0x190)
| r5:00000041 r4:c7809000
|[<c022fc68>] (dev_change_flags+0x0/0x190) from [<c0270250>] (devinet_ioctl+0x2f0/0x710)
| r7:c7221e70 r6:c7aadb00 r5:00000000 r4:00000001
|[<c026ff60>] (devinet_ioctl+0x0/0x710) from [<c02717c8>] (inet_ioctl+0xd4/0x110)
|[<c02716f4>] (inet_ioctl+0x0/0x110) from [<c021fb74>] (sock_ioctl+0x1f4/0x254)
| r4:c7242b40
|[<c021f980>] (sock_ioctl+0x0/0x254) from [<c00b8160>] (vfs_ioctl+0x38/0x98)
| r6:beec9bb8 r5:00008914 r4:c7242b40
|[<c00b8128>] (vfs_ioctl+0x0/0x98) from [<c00b873c>] (do_vfs_ioctl+0x484/0x4d4)
| r6:00008914 r5:c7242b40 r4:c74db1c0
|[<c00b82b8>] (do_vfs_ioctl+0x0/0x4d4) from [<c00b87cc>] (sys_ioctl+0x40/0x64)
|[<c00b878c>] (sys_ioctl+0x0/0x64) from [<c00269a0>] (ret_fast_syscall+0x0/0x2c)
|[42949399.520000] r7:00000036 r6:beec9c80 r5:00000041 r4:beec9bb8
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Acked-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Supporting AR8131, and AR8132.
Signed-off-by: Jie Yang <jie.yang@atheros.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit f55c21fd9a92a444e55ad1ca4e4732d56661bf2e ("forcedeth: call
restore mac addr in nv_shutdown path"), which was introduced to fix
the regression tracked at
http://bugzilla.kernel.org/show_bug.cgi?id=11358 causes the
wake-on-lan mac to be reversed in the shutdown path. Apparently the
forcedeth situation is rather messy in that the mac we need to
writeback for a subsequent modprobe to work is exactly the reverse of
what is needed for proper wake-on-lan.
The following patch explains the situation in the comments and
makes the call to nv_restore_mac_addr() conditional (only called if
we are not really going for poweroff).
Tobias Diedrich wrote:
> Hmm, I had not tried WOL for some time.
> With 2.6.29-rc3 is see the following behaviour:
>
> State WOL Behaviour
> ------------------------------
> shutdown reversed MAC
> disk/shutdown reversed MAC
> disk/platform OK
>
> Apparently nv_restore_mac_addr() restores the MAC in the wrong order
> for WOL (at least for my PCI_DEVICE_ID_NVIDIA_NVENET_15). platform
> works, because the MAC is not touched in the nv_suspend() path.
>
> A possible fix might be to only call nv_restore_mac_addr() if
> system_state != SYSTEM_POWER_OFF.
With the following patch:
shutdown OK
disk/shutdown OK
disk/platform OK
kexec OK
Signed-off-by: Tobias Diedrich <ranma+kernel@tdiedrich.de>
Tested-by: Philipp Matthias Hahn <pmhahn@titan.lahn.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (32 commits)
wimax: fix oops in wimax_dev_get_by_genl_info() when looking up non-wimax iface
net: 4 bytes kernel memory disclosure in SO_BSDCOMPAT gsopt try #2
netxen: fix compile waring "label ‘set_32_bit_mask’ defined but not used" on IA64 platform
bnx2: Update version to 1.9.2 and copyright.
bnx2: Fix jumbo frames error handling.
bnx2: Update 5709 firmware.
bnx2: Update 5706/5708 firmware.
3c505: do not set pcb->data.raw beyond its size
Documentation/connector/cn_test.c: don't use gfp_any()
net: don't use in_atomic() in gfp_any()
IRDA: cnt is off by 1
netxen: remove pcie workaround
sun3: print when lance_open() fails
qlge: bugfix: Add missing rx buf clean index on early exit.
qlge: bugfix: Fix RX scaling values.
qlge: bugfix: Fix TSO breakage.
qlge: bugfix: Add missing dev_kfree_skb_any() call.
qlge: bugfix: Add missing put_page() call.
qlge: bugfix: Fix fatal error recovery hang.
qlge: bugfix: Use netif_receive_skb() and vlan_hwaccel_receive_skb().
...
|
|
used" on IA64 platform
When compile the latest kernel on IA64 platform,I got a warning:
drivers/net/netxen/netxen_nic_main.c:203: warning: label ‘set_32_bit_mask’
defined but not used
We do not need label ‘set_32_bit_mask’ on IA64 platform,So move it to #else.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If errors are reported on a frame descriptor, we need to
account for the buffer pages that may have been used for this
error packet and recycle them. Otherwise, we may get the wrong
pages for the next packet.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
New firmware fixes a data corruption issue when receiving and
placing jumbo frames into host buffers. In some cases, the
buffer descriptor is not updated correctly and this will lead
to the driver linking the wrong number of pages into the SKB.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
New firmware fixes a data corruption issue when receiving and
placing jumbo frames into host buffers. In some cases, the
buffer descriptor is not updated correctly and this will lead
to the driver linking the wrong number of pages into the SKB.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ensure that we do not set pcb->data.raw beyond its size, print an error message
and return false if we attempt to. A timout message was printed one too early.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If no prior break occurs, cnt reaches 101 after the loop, so we are still able
to change speed when cnt has become 100.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove workaround for pcie bug in early revisions of NX3031
(rev 41 or earlier). This is taken care of during firmware init.
The workaround required writing pcie config reg of every
pcie function on a card, not all of which are enabled.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With while (--i > 0) { ... } i reaches 0; print when lance_open() fails
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The large receive buffer queue is not properly tracking the current
index in the case where an early exit occurs. This can happen when a
page alloc or dma mapping fails. If this occurs the queue will get
out of sync and invalid indexes can be written to the hardware.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Receive packets were only scaling across 2 of the receive queues. The
value was hardcoded to 2 instead of being based on how many rx queues
were running.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Moved the buffer mapping to a point after TSO logic has modified the
iph->check field. We were seeing stale data on the PCIe bus.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We put the skb back if we can't get mapping for it. We don't
want unmapped buffers on our receive buffer queue.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We put the page back if we can't get mapping for it. We don't
want unmapped buffers on our receive buffer queue.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace calls to vlan_hwaccel_rx() and netif_rx().
Thanks to Dave Miller for pointing out the the driver was making
the wrong upcall for passing packets into the stack.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With while (limit--) { ... } limit reaches -1, so 0 means success.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Here we do two things:
First, revert "iwlwifi: save PCI state before suspend, restore after
resume". That misguided patch led to being unable to use iwlwifi
devices after resume.
Next, indicate to PCI driver that the saved PCI state is valid during suspend.
We restore PCI state and enable the device when network interface is created,
similarly PCI state is saved and the device is disabled when network interface
is removed. Thus, when .suspend is called the PCI state is saved and device
is disabled. This is the case even if an interface is never created as PCI
state is saved and device disabled during .probe.
PCI driver assumes PCI state is saved in .suspend. Saving the state at this
time will save state of disabled device and thus cause problems during
resume (resuming a disabled device). We thus indicate directly to PCI
driver that current PCI saved state is valid.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Alex Riesen <fork0@users.sf.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Three people (Petr Mensik <pihhan@cipis.net>
["si" should be U+0161 U+00ED], Stephen Ho <stephenhoinhk@gmail.com>
on zd1211-devs and Ismael Ojeda Perez <iojedaperez@gmail.com>
on linux-wireless) reported success in getting TP-Link WN322G/WN422G
working by treating MAXIM_NEW_RF(0x08) as UW2453_RF(0x09) for rf
chip hardware initialization.
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Tested-by: Petr Mensik <pihhan@cipis.net>
Tested-by: Stephen Ho <stephenhoinhk@gmail.com>
Tested-by: Ismael Ojeda Perez <iojedaperez@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Christoph Biedl <sourceforge.bnwi@manchmal.in-ulm.de> reported success
in the sourceforge zd1211 mailing list on this addition. This product ID
was supported by the vendor driver ZD1211LnxDrv 2.22.0.0 (and possibly
earlier) and it probably should have been added earlier.
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Tested-by: Christoph Biedl <sourceforge.bnwi@manchmal.in-ulm.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Under memory pressure, we may not be able to allocate a new skb for
new packets. If the allocation fails, ath5k_tasklet_rx will exit but
will leave a buffer in the list with a NULL skb, eventually triggering
a BUG_ON.
Extract the skb allocation from ath5k_rxbuf_setup() and change the
tasklet to allocate the next skb before accepting a packet.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Currently, the sunhme driver installs SBus Quattro interrupt handler
when at least one HME card was initialized correctly and at least one
Quattro card is present. This breaks when a Quattro card fails
initialization for whatever reason - IRQ is registered and OOPS happens
when it fires.
The solution, as suggested by David Miller, was to keep track which
cards of the Quattro bundles have been initialized, and request/free the
Quattro IRQ only when all four devices have been successfully
initialized.
The patch only touches SBus initialization - PCI init already resets the
card pointer to NULL on init failure.
The patch has been tested on Sun E3500 with SBus and PCI single HME
cards and one PCI Quattro HME card in a situation where any PCI card
failed init when the SBus routines tried to init them by mistake.
Additionally it replaces Quattro request_irq panic with error return -
if this card fails to work, at least let the others work.
Tested on E450 with PCI HME and PCI Quad HME.
[ Minor coding style fixups -DaveM ]
Signed-off-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mdc pin should always be output. Initialize it as output,
so each board code does not need to do this.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (23 commits)
bridge: Fix LRO crash with tun
IPv6: fix to set device name when new IPv6 over IPv6 tunnel device is created.
gianfar: Fix boot hangs while bringing up gianfar ethernet
netfilter: xt_sctp: sctp chunk mapping doesn't work
netfilter: ctnetlink: fix echo if not subscribed to any multicast group
netfilter: ctnetlink: allow changing NAT sequence adjustment in creation
netfilter: nf_conntrack_ipv6: don't track ICMPv6 negotiation message
netfilter: fix tuple inversion for Node information request
netxen: fix msi-x interrupt handling
de2104x: force correct order when writing to rx ring
tun: Fix unicast filter overflow
drivers/isdn: introduce missing kfree
drivers/atm: introduce missing kfree
sunhme: Don't match PCI devices in SBUS probe.
9p: fix endian issues [attempt 3]
net_dma: call dmaengine_get only if NET_DMA enabled
3c509: Fix resume from hibernation for PnP mode.
sungem: Soft lockup in sungem on Netra AC200 when switching interface up
RxRPC: Fix a potential NULL dereference
r8169: Don't update statistics counters when interface is down
...
|
|
Ira Snyder found that commit 8c7396aebb68994c0519e438eecdf4d5fa9c7844
"gianfar: Merge Tx and Rx interrupt for scheduling clean up ring" can
cause hangs. It's because there was removed clearing of interrupts in
gfar_schedule_cleanup() (which is called by an interrupt handler) in
case when netif scheduling has been disabled. This patch brings back
this action and a comment.
Reported-by: Ira Snyder <iws@ovro.caltech.edu>
Reported-by: Peter Korsgaard <jacmet@sunsite.dk>
Bisected-by: Ira Snyder <iws@ovro.caltech.edu>
Tested-by: Peter Korsgaard <jacmet@sunsite.dk>
Tested-by: Ira Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o Cut down msi-x vectors from 8 to 1 since only one is used for now.
o Use separate handler for msi-x, that doesn't unnecessarily scrub
msi status register.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DescOwn should not be set, thus allowing the chip to use the
descriptor, before everything else is set up correctly.
Signed-off-by: Risto Suominen <Risto.Suominen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tap devices can make use of a small MAC filter set via the
TUNSETTXFILTER ioctl. The filter has a set of exact matches
plus a hash for imperfect filtering of additional multicast
addresses. The current code is unbalanced, adding unicast
addresses to the multicast hash, but only checking the hash
against multicast addresses. This results in the filter
dropping unicast addresses that overflow the exact filter.
The fix is simply to disable the filter by leaving count set
to zero if we find non-multicast addresses after the exact
match table is filled.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Unfortunately, the OF device tree nodes for SBUS and PCI
hme devices have the same device node name on some systems.
So if the name of the parent node isn't 'sbus', skip it.
Based upon an excellent report and detective work by
Meelis Roos and Eric Brower.
Signed-off-by: David S. Miller <davem@davemloft.net>
Tested-by: Meelis Roos <mroos@linux.ee>
|
|
From: Ondrej Zary <linux@rainbow-software.org>
last year, I posted a patch which fixed hibernation on 3c509
cards. That was back in 2.6.24. It worked fine in 2.6.25. But then I
stopped using hibernation (as it did not work with my new IT8212 RAID
controller).
Now I fixed it and noticed that 3c509 does not wake up properly
anymore (in 2.6.28) - neither in PnP nor in ISA modes. ifconfig
down/up makes the card work again in PnP mode. However, in ISA mode,
ifconfig up ends with "No such device" error.
Comparing the 3c509 driver between 2.6.25 and 2.6.28, there's only
some statistics-related change. So the cause of the problem must be
somewhere else.
This patch makes the resume work in PnP mode, but it's still not
enough for ISA mode.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
From: Ilkka Virta <itvirta@iki.fi>
In the lockup situation the driver seems to go off in an eternal storm
of interrupts right after calling request_irq(). It doesn't actually
do anything interesting in the interrupt handler. Since connecting the link
afterwards works, something later in initialization must fix this.
Looking at gem_do_start() and gem_open(), it seems that the only thing
done while opening the device after the request_irq(), is a call to
napi_enable().
I don't know what the ordering requirements are for the
initialization, but I boldly tried to move the napi_enable() call
inside gem_do_start() before the link state is checked and interrupts
subsequently enabled, and it seems to work for me. Doesn't even break
anything too obvious...
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some Realtek chips (RTL8169sb/8110sb in my case) are unable to retrieve
ethtool statistics when the interface is down. The process stays in
endless loop in rtl8169_get_ethtool_stats. This is because these chips
need to have receiver enabled (CmdRxEnb bit in ChipCmd register) that is
cleared when the interface is going down. It's better to update statistics
only when the interface is up and otherwise return copy of statistics
grabbed when the interface was up (in rtl8169_close).
It is interesting that PCI-E NICs (like 8168b/8111b...) are not affected.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
Revert "tcp: Always set urgent pointer if it's beyond snd_nxt"
ipv6: Copy cork options in ip6_append_data
udp: Fix UDP short packet false positive
gianfar: Fix potential soft reset race
gianfar: Fix BD_LENGTH_MASK definition
cxgb3: Fix lro switch
iwlwifi: save PCI state before suspend, restore after resume
iwlwifi: clean key table in iwl_clear_stations_table
|
