| Age | Commit message (Collapse) | Author |
|---|
|
ELP mode is working now, let's enable it so that the firmware can sleep
and reduce power consumption.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Check the return call from wl12xx_ps_elp_wakeup() and bail out if it
fails. This shouldn't happen, but if does there's a fundamental low
level issue.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The wakeup call was done too deep in code path, it's better to wakeup
chip from higher levels. This will also reduce wakeup calls significantly.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The function doesn't lock the mutex before sending the acx.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
CMD_TEST via netlink API has been broken since
e29c3f59cfbc38c3b481a2694b08962da19c4664: cmd and acx interface rework.
The user of the interface sends the request in a buffer without the
wl12xx_command header but expects the response to have the wl12xx_command
header (with id and status).
This patch reverts the e29c3f5 commit for cmd.c:wl12xx_cmd_test
and implements the needed wrapper functionality in netlink.c. Now the
API of wl12xx_cmd_test and rest of wl12xx_cmd_* commands in cmd.c are
similar.
Signed-off-by: Ari Kauppi <Ext-Ari.Kauppi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
A warning message in wl12xx_acx_event_mbox_mask has a copy/paste
error. Fix it to print the correct acx command.
Signed-off-by: Ari Kauppi <Ext-Ari.Kauppi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add support for block reading (multiple bytes) from a fixed chipset
register address. This is required for the wl1271 TX data path.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Moved wl1251 TX path implementation into chip specific files to enable
parallel implementation for the wl1271 TX path.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Changed the function wl12xx_acx_wake_up_conditions() so that it receives an
argument with the actual wake up condition, instead of having
WAKE_UP_EVENT_DTIM_BITMAP hardcoded. This is needed because we have to use
different conditions in 1271.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
In the wl1271 implementation, we need to read memory from the register
partition using fixed addresses. This change adds the possibility to request
fixed address when calling wl12xx_spi_read() or wl12xx_spi_reg_read().
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch adds the code that recognizes the new WL1271 chip revision (PG 2.0).
Full support for this chip is not yet implemented and support for WL1271 PG 1.0
is not guaranteed anymore.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
With WL1271, the firmware version can only be read right after booting the
chip. To keep WL1251 aligned with this procedure, the code that reads the
firmware version initially has been moved to a common place where it can be
read from both chipsets.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
In some cases we need to read more than 32 bits from the register area.
These functions were added to support that, like the existing
wl12xx_spi_mem_read() and wl12xx_spi_mem_write() already do for large blocks
in the memory area.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The chipset source interrupt source configuration during fw wakeup was
blocking interrupts on the wl1271. The configuration is effectively
unused here as it is used to trigger an interrupt for the chipset
wake-up event, which is not handled, or waited for, in the fw wakeup
anyway on either wl1251 or wl1271.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Rx descriptor was incorrectly allocated from stack, use struct wl12xx
instead. Needed for DMA transfers.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
As a side effect the transfer is now DMA safe.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Needed for DMA transfers.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Needed for DMA safe transfers.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This is now DMA safe.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Resources were not freed properly in some cases.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The buffer is needed for DMA safe transfers.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Rework cmd and acx interfaces, it was just too confusing earlier. Now
all commands need to contain all the needed headers, either just cmd
headers or both cmd and acx headers. This accomplish to remove the
extra copy done for each command. The interfaces are now properly
documented as well.
Also try to make all commands safe for DMA transfers. I might have missed
some, but most of them should be fixed now.
And this is not all! As a free bonus you will also get some cosmetic
cleanups and code reorganisation. Order today!
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch moves the sanity check on beacon interval
which was done only for mesh mode to all operating
modes just to be safe.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Power save support depends on the firmware capabilities rather than the
card's hardware interface. Use the FW_CAPINFO_PS bit in the firmware
capabilities mask throughout the driver in place of the redundant
ps_supported flag and don't make decisions about PS support in the
interface drivers (with the exception of a special case in the USB
driver).
V2: put the USB special case in the right place.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Cardbus and some PCI cards use hardware LEDs rather than software GPIOs.
Program them with the proper blink patterns when idle, scanning or
associated. Fixes http://bugzilla.kernel.org/show_bug.cgi?id=13288.
Tested-by: Frans Pop <elendil@planet.nl>
Tested-by: Mark Hindley <mark@hindley.org.uk>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ah_gpios array isn't used, and ah_current_channel can be a pointer
instead of an embedded struct. Removing these and some other
write-only variables, and moving some things around for better
packing and cache utilization saves 116 bytes.
text data bss dec hex filename
121762 472 64 122298 1ddba ath5k_before.ko
121646 472 64 122182 1dd46 ath5k.ko
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We can easily run out of tx buf if there is any stuck in
transmission, so downgrade it to WARN_ON().
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
mac80211 already has one to keep track of number of failure
addba attempts.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
IEEE80211_TX_CTL_AMPDU in tx control flags should be enough
to confirm BA is negotiated for that tid.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
If there was a reason I'm passing the ifidx I cannot
remember it any more and don't see one now, so let's
just pass the pointer itself.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
|
|
Commit c3a8c5b6 ("cxgb3: move away from LLTX") exposed a bug in how
cxgb3 looks up the netdev_queue it stashes away in a qset during
initialization. For multiport devices, the TX queue index it uses is
offset by the first_qset index of each port. This leads to a crash
once LLTX is removed, since hard_start_xmit is called with one TX
queue lock held, while the TX reclaim timer task grabs a different
(wrong) TX queue lock when it frees skbs.
Fix this by removing the first_qset offset used to look up the TX
queue passed into t3_sge_alloc_qset() from setup_sge_qsets().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix coexistence of Fiber Channel over Ethernet (FCoE) and Flow Director (FDIR)
in 82599 and remove the disabling of FDIR when FCoE is enabled.
Currently, FDIR is turned off when FCoE is enabled under the assumption that
FCoE is always enabled with DCB being turned on. However, FDIR does not have
to be turned off all the time when FCoE is enabled since FCoE can be enabled
without DCB being turned on, e.g., use link pause only. This patch makes sure
that when DCB is turned on or off, FDIR is turned on or off correspondingly;
and when FCoE is enabled, it does not disable FDIR, rather, it will have FDIR
set up properly so FCoE and FDIR can coexist regardless of DCB being on or off.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
In the mainline kernel, p54usb will fail because the TX queue length can
become < 0. This problem has been reported as Bugzilla #13725. The failure
is expressed by the following message in the logs:
WARNING: at net/mac80211/tx.c:1325 ieee80211_tx+0x23c/0x298 [mac80211]()
Hardware name: HP Pavilion dv2700 Notebook PC
tx refused but queue active
This problem has been recently observed in the wireless-testing tree, where
a full solution is being tested. That fix is too invasive for 2.6.31-rcX,
but the simple change supplied here will prevent the failure.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Atheros top level menu needs a "depends WLAN_80211" to properly indent
within menuconfig and xconfig interfaces.
This is purely a visual issue but it effects all subsequent drivers.
The issue is the top level menu does not include a dependency on
WLAN_80211 so within the tree structure, Atheros is at the same level as
WLAN_80211 but when WLAN_80211 collapsed, the menu disappears along with
all subsequent drives, so it is really a subordinate.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
There's a race condition -- started can be set to true
before channel is set due to the way mac80211 callbacks
currently work (->start should probably pass the channel
we would like to have initially). For now simply add a
check to hwsim to avoid dereferencing the NULL channel
pointer.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Added support for the Broadcom 4318E chipset on PCMCIA/CF cards. The
4318E can do 802.11A/B/G, only B and G mode are supported in b43.
Signed-off-by: Clyde McPherson <ccmcphe@verizon.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Yevgen Kotikov reported success on the sourceforge zd1211-devs list
with the following details:
Brand/retail: SONY IFU-WLM2
USB-IDs: Vendor: 0x054C Device: 0x0257
chip ID: zd1211b chip 054c:0257 v4802 high 00-0b-6b AL2230_RF pa0 -----
FCC ID: unknown
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Tested-by: Yevgen Kotikov <yevgen.kotikov@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
On a shuttle machine here we got 07b8:6001 device, handled by zd1211rw, which does not work.
Scanning is OK but association does not work, we get "direct probe to AP xxx timed out"
It appears that this simple patch makes the device work perfectly.
This id was already there in initial import of the driver so I don't know if it has ever been
working as ZD1211 (which would mean they changed it and kept the id :( ).
Signed-off-by: Pascal Terjan <pterjan@mandriva.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Drain the MAC TX fifos when a port goes down.
Back pressure might otherwise occur, leading to both
ports of the same adapter to hang.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Override the mac index computation for the gen2 adapter,
as each port is expected to use index 0.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the HW SMT table initialization to avoid random
mss miscomputations for offload connections.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
use request_firmware() to load the phy's EDC programmation
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We don't always see the link status update interrupt
when we come out of reset and the peer is up.
Check and report the link status right before enabling interrupts.
Also fix LED settings, to get a consistent link status.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Max packet size is not the only field in T3C's High Water Mark register.
Mask the register to access this field.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
2 phys are were not getting the Global Tx disable bit set
when powered down, leading to an inconsistent link state
on peer.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add missing SUPPORTED_TP flag.
Update FW version checking.
Do the full initialization even if the FW version is unknown,
it might help catching further issues.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the r6040 device IRQ line is shared we will enter the driver
interrupt service routine, mask off the device interrupt enable
register (MIER) and return with IRQ_NONE, we would then leave the
device with interrupts disabled, this patch fixes that issue.
Reported-by: Steve Holland <sdh4@iastate.edu>
Signed-off-by: Joe Chou <joe.chou@rdc.com.tw>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
