| Age | Commit message (Collapse) | Author |
|---|
|
This is not required as VLAN header is added by device
interface driver, this was causing bad FC_CRC in FCoE pkts when
using VLAN interface.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Removes periodic fcoe_watchdog timer used across all fcoe interface
maintained in fcoe_hostlist instead added new fcoe_queue_timer
per fcoe interface.
Added timer is armed only when some pending skb need to be flushed
as oppose to periodic 1 second fcoe_watchdog, since now
fcoe_queue_timer is used on demand thus set this to 2 jiffies.
Now fcoe_queue_timer is much simple than fcoe_watchdog using lock to
process all fcoe interface from fcoe_hostlist.
I noticed +ve performance result with using 2 jiffies timer as
this helps flushing fcoe_pending_queue quickly.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Currently fcoe_pending_queue.lock held twice for every new skb
adding to this queue when already least one pkt is pending in this
queue and that is not uncommon once skb pkts starts getting queued
here upon fcoe_start_io => dev_queue_xmit failure.
This patch moves most fcoe_pending_queue logic to fcoe_check_wait_queue
function, this new logic grabs fcoe_pending_queue.lock only once to
add a new skb instead twice as used to be.
I think after this patch call flow around fcoe_check_wait_queue
calling in fcoe_xmit is bit simplified with modified
fcoe_check_wait_queue function taking care of adding and
removing pending skb in one function.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
When a sequence is received in response to an exchange we issued previously,
we should check to see if the exchange has completed. If yes, the sequence
should be discarded. Since the exchange might be still in the completion
process, it should be untouched.
Signed-off-by: Steve Ma <steve.ma@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
If we aborted a command, because it timed out we should not use
DID_ABORT. It will fail the command right away back to the upper
layer. We want to use something that indicated that the problem
did not complete normally, but it was not a fatal problem.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
FIP frames should leave the fcoe layer with skb->protocol set to
ETH_P_FIP, not ETH_P_802_3.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
When a reset is sent using fcoeadm on a non-FIP mode NIC,
there's no link flap, so the fcoe_ctlr stays in non-FIP mode.
In that case, FIP wasn't setting the flogi_oxid or map_dest flag,
causing the FLOGI to be sent with the both wrong source MAC and
the wrong destination MAC address, causing it to fail.
This leads to a non-functioning HBA until a link flap or
instance delete/create.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This driver needs dst_cache->dev so it should include net/dst.h
to ensure that it builds. While net/tcp.h probably includes it
already, we shouldn't rely on that since there is no guarantee
that this won't change in future.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Bump driver version
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
There are several scenarios where the ibmvfc driver needs to
try to log back into a target on the fabric. Today when these events
occur, we simply go through re-discovery for all attached targets,
assuming that either the query of the name server or an ADISC will
indicate we might need to log back into the target, which doesn't
work for all scenarios. Fix this by taking note of the affected target(s)
in these conditions and ensuring we try to PLOGI back into the target.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
For certain scenarios during device rediscovery, we detect we need
to log back into a target. Currently we do just that - PLOGI/PRLI
back into the target. Change the code to delete and add the target
from the FC transport layer as well, to ensure we handle any cases
where the target may have changed.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
The virtual I/O server controlling the NPIV adapter associated with
a virtual fibre channel adapter can send a HALT event to the client.
When this occurs, the client can no longer send commands until a RESUME
is received. By adding support for flush on halt, we will get all of
our outstanding commands flushed back before the Virtual I/O server
enters the halt state, eliminating potential command timeouts for
outstanding commands which might occur if we did not support this feature.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This patch adds support for a new command supported by the Virtual I/O
Server, NPIV Logout. The command will abort all outstanding commands
and log out of the fabric. Currently, the only way to do this is
by breaking the CRQ, which can take a fairly long time when lots of
commands are outstanding. The NPIV Logout commands provides a mechanism
to accomplish virtually the same function, but is much faster.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Fixes the following deadlock scenario shown below. We currently allow
queuecommand to send commands when the ibmvfc workqueue is scanning for
new rports, so we should also allow EH to function at this time as well.
scsi_eh_3 D 0000000000000000 12304 1279 2
Call Trace:
[c0000002f7257730] [c0000002f72577e0] 0xc0000002f72577e0 (unreliable)
[c0000002f7257900] [c0000000000118f4] .__switch_to+0x158/0x1a0
[c0000002f72579a0] [c0000000004f8b40] .schedule+0x8d4/0x9dc
[c0000002f7257b60] [c0000000004f8f08] .schedule_timeout+0xa8/0xe8
[c0000002f7257c50] [d0000000001d23e0] .ibmvfc_wait_while_resetting+0xe4/0x140 [ibmvfc]
[c0000002f7257d20] [d0000000001d3984] .ibmvfc_eh_abort_handler+0x60/0xe4 [ibmvfc]
[c0000002f7257dc0] [d000000000366714] .scsi_error_handler+0x38c/0x674 [scsi_mod]
[c0000002f7257f00] [c0000000000a7470] .kthread+0x78/0xc4
[c0000002f7257f90] [c000000000029b8c] .kernel_thread+0x4c/0x68
ibmvfc_3 D 0000000000000000 12432 1280 2
Call Trace:
[c0000002f7253540] [c0000002f72535f0] 0xc0000002f72535f0 (unreliable)
[c0000002f7253710] [c0000000000118f4] .__switch_to+0x158/0x1a0
[c0000002f72537b0] [c0000000004f8b40] .schedule+0x8d4/0x9dc
[c0000002f7253970] [c0000000004f8e98] .schedule_timeout+0x38/0xe8
[c0000002f7253a60] [c0000000004f80cc] .wait_for_common+0x138/0x220
[c0000002f7253b40] [c0000000000a2784] .flush_cpu_workqueue+0xac/0xcc
[c0000002f7253c10] [c0000000000a2960] .flush_workqueue+0x58/0xa0
[c0000002f7253ca0] [d0000000000827fc] .fc_flush_work+0x4c/0x64 [scsi_transport_fc]
[c0000002f7253d20] [d000000000082db4] .fc_remote_port_add+0x48/0x6c4 [scsi_transport_fc]
[c0000002f7253dd0] [d0000000001d7d04] .ibmvfc_work+0x820/0xa7c [ibmvfc]
[c0000002f7253f00] [c0000000000a7470] .kthread+0x78/0xc4
[c0000002f7253f90] [c000000000029b8c] .kernel_thread+0x4c/0x68
fc_wq_3 D 0000000000000000 10720 1283 2
Call Trace:
[c0000002f559ac30] [c0000002f559ace0] 0xc0000002f559ace0 (unreliable)
[c0000002f559ae00] [c0000000000118f4] .__switch_to+0x158/0x1a0
[c0000002f559aea0] [c0000000004f8b40] .schedule+0x8d4/0x9dc
[c0000002f559b060] [c0000000004f8e98] .schedule_timeout+0x38/0xe8
[c0000002f559b150] [c0000000004f80cc] .wait_for_common+0x138/0x220
[c0000002f559b230] [c0000000002721c4] .blk_execute_rq+0xb4/0x100
[c0000002f559b360] [d00000000036a1f8] .scsi_execute+0x118/0x194 [scsi_mod]
[c0000002f559b420] [d00000000036a32c] .scsi_execute_req+0xb8/0x124 [scsi_mod]
[c0000002f559b500] [d0000000000c1330] .sd_sync_cache+0x8c/0x108 [sd_mod]
[c0000002f559b5e0] [d0000000000c15b4] .sd_shutdown+0x9c/0x158 [sd_mod]
[c0000002f559b660] [d0000000000c16d0] .sd_remove+0x60/0xb4 [sd_mod]
[c0000002f559b700] [c000000000392ecc] .__device_release_driver+0xd0/0x118
[c0000002f559b7a0] [c000000000393080] .device_release_driver+0x30/0x54
[c0000002f559b830] [c000000000392108] .bus_remove_device+0x128/0x16c
[c0000002f559b8d0] [c00000000038f94c] .device_del+0x158/0x234
[c0000002f559b960] [d00000000036f078] .__scsi_remove_device+0x5c/0xd4 [scsi_mod]
[c0000002f559b9f0] [d00000000036f124] .scsi_remove_device+0x34/0x58 [scsi_mod]
[c0000002f559ba80] [d00000000036f204] .__scsi_remove_target+0xb4/0x120 [scsi_mod]
[c0000002f559bb10] [d00000000036f338] .__remove_child+0x2c/0x44 [scsi_mod]
[c0000002f559bb90] [c00000000038f11c] .device_for_each_child+0x54/0xb4
[c0000002f559bc50] [d00000000036f2e0] .scsi_remove_target+0x70/0x9c [scsi_mod]
[c0000002f559bce0] [d000000000083454] .fc_starget_delete+0x24/0x3c [scsi_transport_fc]
[c0000002f559bd70] [c0000000000a2368] .run_workqueue+0x118/0x208
[c0000002f559be30] [c0000000000a2580] .worker_thread+0x128/0x154
[c0000002f559bf00] [c0000000000a7470] .kthread+0x78/0xc4
[c0000002f559bf90] [c000000000029b8c] .kernel_thread+0x4c/0x68
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
The ibmvfc driver currently logs errors during discovery for several
transient fabric errors, which generally get retried. If retries
do not work, we see multiple errors in the log. If retries do work,
we see errors in the log which may be confusing since the retry worked.
This patch enhances the discovery time error logging to only log errors
for command failures during discovery if all allowed retries have been
used up. The existing behavior of logging all failures can be restored
by setting the hosts log_level to a value of 3 or greater.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Use DEVICE_ATTR macro for defining device sysfs attributes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Since target allocations can occur while resetting the virtual adapter,
we shouldn't be using GFP_KERNEL for them as it could hang. Switch to
use GFP_NOIO.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Fix an obvious bug in processing error responses for SCSI commands
which can result in successful responses being incorrectly returned
with DID_ERROR.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
The async split up of probing in sd.c created a potential failure case where
something goes wrong with device_add(), but which we don't recover properly.
Since, in general, asynchronous error handling is hard, move the device_add()
into the asynchronous path (it should be fast) and make sure all the deferred
processing cannot fail.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
The Documentation is incorrect (we removed some functions referred to), and
none of the bug warnings now apply. Additionally remove the spurious check on
the return from blk_get_request() which can't fail if __GFP_WAIT is passed in.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Add support for persistent vport definitions at creation at boot time
Also includes a few misc fixes for:
- conversion to vpi name from vport slang name
- couple of small mailbox references
- some additional discovery mods
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Miscellaneous Changes:
- Convert from SLI2_ACTIVE flag to more correct SLI_ACTIVE (generic) flag
- Reposition log verbose messaging definitions
- Update naming for vpi object name from vport slang name
- Handle deferred error attention condition
- Add 10G link support
- Small bug fixup
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Update of copyrights on modified files
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
SLI4 supports both FC and FCOE, with some extended topology objects.
This patch adss support for the objects, and updates the disovery
engines for their use.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
The mailbox commands themselves are the same, or very similar to
their SLI3 counterparts. This patch genericizes mailbox command
handling and adds support for the new SLI4 mailbox queue.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Adds support for the new queues in the SLI-4 interface. There are :
- Work Queues - host-to-adapter for fast-path traffic
- Mailbox Queues - host-to-adapter for control (slow-path)
- Buffer Queues - host-to-adapter for posting buffers for async receive
- Completion Queues - adapter-to-host for posting async events,
completions for fast or slow patch work, receipt of async
receive traffic
- Event Queues - tied to MSI-X vectors, binds completion queues with
interrupts
These patches add the all the support code to tie into command submission
and response paths, updates the interrupt handling, etc.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Adds new hardware and interface definitions.
Adds new interface routines - utilizing the reorganized layout of the
driver. Adds SLI-4 specific functions for attachment, initialization,
teardown, etc.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Preps the organization of the driver so that the bottom half, which
interacts with the hardware, can share common code sequences for
attachment, detachment, initialization, teardown, etc with new hardware.
For very common code sections, which become specific to the interface
type, the driver uses an indirect function call. The function is set at
initialization. For less common sections, such as initialization, the
driver looks at the interface type and calls the routines relative to
the interface.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This allows fnic to configure number of retries for lport and rport
separately.
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Acked-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Bump driver version.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This fix's is for all local function so their name has the "_" preceeding
the module name, then function name. Most the code is already is using this
naming convention.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This patch will find an active mid for a query_task request via the ioctl path.
This code is already there for task_abort, so this patch combining code using
the same fuction _ctl_set_task_mid(), previously _ctl_do_task_abort().
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Adding new eh_target_reset_handler for target reset. Change the
eh_device_reset_handler so its sending
MPI2_SCSITASKMGMT_TASKTYPE_LOGICAL_UNIT_RESET, instead of
MPI2_SCSITASKMGMT_TASKTYPE_TARGET_RESET. Add new function
_scsih_scsi_lookup_find_by_lun as a sanity check to insure I_T_L commands are
completed upon completing lun reset.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This add support for type 1 and 3 DIF support per the Oracle API.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Signed-off-by: Ying Chu <jasonchu@marvell.com>
Signed-off-by: Andy Yan <ayan@marvell.com>
Signed-off-by: Ke Wei <kewei@marvell.com
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This patch just adds some debug statements for the abort
and completion paths.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
If a task did not complete normally due to a TMF, libiscsi will
now complete the task with the state ISCSI_TASK_ABRT_TMF. Drivers
like bnx2i that need to free resources if a command did not complete normally
can then check the task state. If a driver does not need to send
a special command if we have dropped the session then they can check
for ISCSI_TASK_ABRT_SESS_RECOV.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Instead of having libiscsi check if the offload bit is set, have
it check if the lld created a work queue. I think this is more
clear.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
If the session is failed, but we have not yet fully transitioned
to the recovery stage we were still queueuing IO. The idea is
that for some failures we can recvover at the command level
and still continue to execute other IO. Well, we never have
added the recovery within a command code, so queueing up IO here
just creates the possibility that it might time time out so
this just has us requeue the IO the scsi layer for now.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
bnx2i needs to send a hardware specific cleanup command if
a command has not completed normally (iscsi/scsi response from
target), and the session is still ok (this is the case when we
send a TMF to stop the command).
At this time it will need to drop the session lock. The problem
with the current code is that fail_all_commands assumes we
will hold the lock the entire time, so it uses list_for_each_entry_safe.
If while bnx2i drops the session lock multiple cmds complete then
list_for_each_entry_safe will not handle this correctly.
This patch removes the running lists and just has us loop over
the cmds array (in later patches we will then replace that
array with a block tag map at the session level). It also fixes
up the completion path so that if the TMF code and the normal recv
path were completing the same command then they both do not try
to do release the refcount taken when the task is queued.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
If we have not got any pdus for recv_timeout seconds, then we will
send a iscsi ping/nop to make sure the target is still around. The
problem is if this is a slow link, and the ping got queued after
the data for a data_out (read), then the transport code could think
the ping has failed when it is just slowly making its way through
the network. This patch has us check if we are making progress while
the nop is outstanding. If we are still reading in data, then we
do not fail the session at that time.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Everytime we read in a pdu libiscsi will update a tracking field.
It uses this to decide when to check if the transport might be bad.
If we have not got data in recv_timeout seconds then we will
send a iscsi ping/nop.
If we are on a slow link then it could take a while to read in all
the data for a data_in. In that case we might send a ping/nop when
we do not need to or we might drop a session thinking it is bad
when the lower layer is making forward progress on it.
This patch has libiscsi_tcp update the recv tracking for each skb
(basically network packet from our point of view) instead of the
entire iscsi pdu+data, so we account for these cases where data is
coming in slowly.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
If we are responding to a nop from the target by sending our nop,
and the session is getting torn down, then iscsi_start_session_recovery
could set the conn stop bits while the recv path is sending the nop
response and we will hit the bug ons in __iscsi_conn_send_pdu.
This has us check the state in __iscsi_conn_send_pdu and fail all
incoming mgmt IO if we are not logged in and if the pdu is not login
related. It also changes the ordering of the setting of conn stop state
bits so they are set after the session state is set (both are set under
the session lock).
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This has iscsi_data_in_rsp call iscsi_update_cmdsn when a pdu is
completed like is done for other pdu's that are don.
For libiscsi_tcp, this means that it calls iscsi_update_cmdsn when
it is handling the pdu internally to only transfer data, but if there is
status then it does not need to call it since the completion handling
will do it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
bnx2i needs to be able to look up mgmt task like login and nop, because
it does some processing of them on the completion path. This exports
iscsi_itt_to_task so it can look up the task.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
If we could not allocate the initiator name or some other id like
the hwaddress or netdev, then userspace could deal with the failure
by just running in a dregraded mode.
Now we want to be able to switch values for the params and we
want some feedback, so this patch will check if a string like
the initiatorname could not be allocated and return an error.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
bnx2i does not have one. It currently preallocates the bdt
when the session is setup.
We probably want to change that to a dma pool, then allocate from
the pool in the alloc pdu. Until then check if there is a alloc
pdu callout.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
When we create the tcp/ip connection by calling ep_connect, we currently
just go by the routing table info.
I think there are two problems with this.
1. Some drivers do not have access to a routing table. Some drivers like
qla4xxx do not even know about other ports.
2. If you have two initiator ports on the same subnet, the user may have
set things up so that session1 was supposed to be run through port1. and
session2 was supposed to be run through port2. It looks like we could
end with both sessions going through one of the ports.
Fixes for cxgb3i from Karen Xie.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
