| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Non-ISP24xx cards must have a loop-id in order to query host
statistics.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Limit assignments via qla2x00_model_name[] array to HBA
subsystem vendor IDs equal to QLogic.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Previous work to add asynchronous-scsi-scanning support
(d19044c32baadeb80e135027124a9e845c6f057c) caused peculiar
semantic changes when no cabling was attached to the HBA
whereby unneeded and intrusive 'error-handling' would take
place due to the initial link state being unset.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Similarly to previous LOGO requests on non-24xx hardware,
perform an implicit-LOGO as to avoid the potential 2 *
R_A_TOV delay which can result during an explicit-LOGO
request.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
This includes BIOS, EFI, FCODE and firmware versions.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
No restriction should be placed on the IRQ number assigned
to a given ISP. Original code incorrectly assumed a
non-zero IRQ number assignment by the system. In these
circumstances the proper freeing of the IRQ (via free_irq())
would not take place.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
What DMA for 16bit pcmcia card, anyway? We never do request_dma()
there and ->dma_channel never changes since initialization to -1.
IOW, that call is dead code.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Why TASK_ATTR_HOQ?
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
This patch removes a duplicate device id from the IPR driver. Based on
the ipr.h file, I'm not so sure this was intended to be a duplicate, and
if so, the .h file should be modified to use the proper sub-device id
instead.
This was pointed out to me by Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Set allow_restart=1 for all SAS disks so that they are spun up when needed.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Register libsas's default device reset code with the scsi.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
This patch moves the code that handles SAS failures out of the main EH
function and into a separate function. It also detects commands that have
no sas_task (i.e. they completed, but with error data) and sends them into
scsi_error for processing. This allows us to handle SCSI errors (and
enables auto-spinup as a side effect) instead of dropping them on the
floor and falling into an infinite loop. It also requires the
implementation of a device reset function, which the SAS failure code has
been modified to employ for REQ_DEVICE_RESET.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Export a couple of functions from scsi_error that are needed to handle
failed SCSI commands from the SAS EH.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
make exports GPL and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Get rid of: "warning: ignoring return value of sysfs_create_link..."
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
sas_rphy_delete does two things: it removes the sas_rphy from the transport
layer and frees the sas_rphy. This can be broken down into two functions,
sas_rphy_remove and sas_rphy_free; sas_rphy_remove is of interest to
sas_discover_root_expander because it calls functions that require
sas_rphy_add as a prerequisite and can fail (namely sas_discover_expander).
In that case, sas_discover_root_expander needs to be able to undo the effects
of sas_rphy_add yet leave the job of freeing the sas_rphy to the caller of
sas_discover_root_expander.
This patch also removes some unnecessary code from sas_discover_end_dev
to eliminate an unnecessary cycle of sas_notify_lldd_gone/found for SAS
devices, thus eliminating a sas_rphy_remove call (and fixing a race condition
where a SCSI target scan can come in between the gone and found call).
It also moves the sas_rphy_free calls into sas_discover_domain and
sas_ex_discover_end_dev to complement the sas_rphy_allocation via
sas_get_port_device.
This patch does not change the semantics of sas_rphy_delete.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Currently, sas_form_port checks the given asd_sas_phy's sas_phy to see if
there's already a port attached. If so, the SAS addresses of the port and
the phy are compared to determine if we need to detach from the port
because the addresses don't match or if we can stop; the SAS address stored
in the sas_port reflects whatever device _was_ attached to the port/phy, and
the SAS address stored in the sas_port reflects whatever device we just
discovered. As written, the code detaches from the port if the addresses
_do_ match, and prints an error if they do _not_ match. I believe this to
be incorrect, as it seems more logical to keep the port if the addresses
match (i.e. the phy was reset but the device didn't change), and detach it
they do not (i.e. the device changed).
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Fix a typo in NCR_D700
Signed-off-by Mark Haverkamp <markh@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Received from Mark Salyzyn,
Take the expose_physicals flag and allow the user to select default (physicals
available via /dev/sg), exposed (physicals available via /dev/sd for
experimental reasons) and hidden (physicals blocked from all access). This
expands the functionality of the previous expose_physicals insmod parameter
which was added to support some experimental configurations.
Signed-off-by Mark Haverkamp <markh@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Received from Mark Salyzyn,
Replace all if/else packet formations with platform function calls. This is in
recognition of the proliferation of read and write packet types, and in the
need to migrate to up-and-coming packets for new products.
Signed-off-by Mark Haverkamp <markh@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Received from Mark Salyzyn,
Add in the NEMER/ARK physical register mapping, represented in up and coming
products currently under test at Adaptec.
Signed-off-by Mark Haverkamp <markh@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Received from Mark Salyzyn,
Replace all if/else communication transports with a platform function call.
This is in recognition of the need to migrate to up-and-coming transports.
Currently the Linux driver does not support two available communication
transports provided by our products, these will be added in future patches, and
will expand the platform function set.
Signed-off-by Mark Haverkamp <markh@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Bump driver version to 2.3.1.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Since the pci_block_user_cfg_access API was modified to track
block/unblocks, it was discovered that the ipr driver had a
path through its code (in PCI error recovery) which would unblock
when not previously blocked.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Don't fail initialization of an adapter if the PCI-X registers
cannot be found since it may be a PCI-E adapter.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Since ipr handles dynamic ids, it must handle driver_data
not being set, so remove the current usage of driver_data
so it can be used for other things in future patches.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
fix typos and bump version number
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Alexis Bruemmer <alexisb@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
number to be incorrect
On Wed, 24 Jan 2007, Andrew Morton wrote:
> On Mon, 22 Jan 2007 13:07:20 -0800
> bugme-daemon@bugzilla.kernel.org wrote:
>
> > http://bugzilla.kernel.org/show_bug.cgi?id=7864
> >
> > Summary: A MTIOCTOP/MTWEOF within the early warning will cause
> > the file number to be incorrect
> > Kernel Version: 2.6.19.2
> > Status: NEW
> > Severity: low
> > Owner: io_scsi@kernel-bugs.osdl.org
> > Submitter: ce_reisinger@yahoo.com
> >
> >
> > Write records to a SCSI tape until a write fails with a ENOSPC (you have reached
> > early warning.
> > Now perform a:
> > struct mtget before, after;
> > ioctl(fd, MTIOCGET, &before);
> > struct mtop mtop = { MTWEOF, 1 };
> > ioctl(fd, MTIOCTOP, &mtop);
> > ioctl(fd, MTIOCGET, &after);
> >
> > Check the value of mt_fileno in the before and after structures. Notice the
> > after is 2 greater then the before.
> >
> > The problem appears to be in the block of code starting at line 2817 in st.c.
> > This block is entered because the drive did return a CHECK CONDITION with NO
> > SENSE and the SENSE_EOM bit set. At lines 2824/5 the fileno is incremented. But
> > it has already been increased by the number of filemarks requested by the
> > MTIOCTOP. I believe that the residue count in the sense data should be
> > subtracted from fileno, not a increment as is done.
> >
>
> Thanks. Could you please send us a tested patch to fix these things, as
> per http://www.zip.com.au/~akpm/linux/patches/stuff/tpp.txt ?
>
The analysis is basically correct and explains the bug. According to the
SCSI standards, the sense code is NO SENSE or RECOVERED ERROR in case
writing filemark(s) succeeds. If it fails (partly or completely) the sense
code is VOLUME OVERFLOW. The patch below is tested to fix the case when
one filemark is successfully written after the EOM early warning. It
should also fix the case at real EOM but this has not been tested.
Carl, thanks for reporting the bug and providing the analysis for the fix.
Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
The included patch fixes the following issues:
1. qla3xxx/qla4xxx co-existence issue which can result in a lockup
when qla3xxx driver is unloaded, or when ifdown; ifup is performed on
one of the interfaces correponding to qla3xxx. This is because qla4xxx
HBA supports one ethernet and iscsi interfaces per port. Both iscsi
and ethernet interfaces share the same state machine. The problem has
to do with synchronizing access to the state machine in the event of a
reset
2. mutex_lock() is sometimes not followed by mutex_unlock() prior to
invoking a msleep() in qla4xxx_mailbox_command()
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
I had thought that all drivers which didn't call scsi_scan_host()
called scsi_scan_target(). Some, such as sbp2, mptsas and libata-scsi,
call scsi_add_device() or __scsi_add_device(). We just need to wait
for the currently executing async scans to complete first. This is the
same code that's in scsi_scan_target(), except that we have to return
an error instead of void when we're declining to scan at all.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (30 commits)
[SCSI] qla1280: set residual correctly
[SCSI] fusion: bump version
[SCSI] fusion: MODULE_VERSION support
[SCSI] fusion: power pc and miscellaneous bug fixs
[SCSI] fusion: fibre channel: return DID_ERROR for MPI_IOCSTATUS_SCSI_IOC_TERMINATED
[SCSI] megaraid_sas: Update module author
[SCSI] 3ware 8000 serialize reset code
[SCSI] sr: fix error code check in sr_block_ioctl()
[SCSI] scsi: lpfc error path fix
[SCSI] aacraid: Product List Update
[SCSI] libiscsi: fix senselen calculation
[SCSI] iscsi: simplify IPv6 and IPv4 address printing
[SCSI] iscsi: newline in printk
[SCSI] iscsi: fix crypto_alloc_hash() error check
[SCSI] iscsi: fix 2.6.19 data digest calculation bug
[SCSI] scsi_scan: fix report lun problems with CDROM or RBC devices
[SCSI] qla2xxx: Update version number to 8.01.07-k4.
[SCSI] qla2xxx: Use generic isp_ops.fw_dump() function.
[SCSI] qla2xxx: Perform a fw-dump when an ISP23xx RISC-paused state is detected.
[SCSI] qla2xxx: Correct reset handling logic.
...
|
|
The EH should fall into I_T recovery (and potentially stronger
remedies) if ABORT TASK fails.
Signed-off-by: Alexis Bruemmer <alexisb@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Track sas_ha_struct state so that we ignore events that come in while
we're shutting things down.
Signed-off-by: Malahal Naineni <malahal@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Convert the phy port locks to use irq spinlocks.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Add the necessary hooks to the aic94xx driver to support the asynchronous SCSI
device scan infrastructure.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Allowing the phy reset controls to be world-triggerable does not seem like
a terribly good idea because SAS devices can be disrupted (and ATA devices
are really disrupted) by a phy reset. By default only root should be able
to do things like that.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Extend the use of the DDB lock to include all DDB accesses, because
DDB updates now occur from multiple threads. This fixes the SMP timeout
problems that we were occasionally seeing with a x260, because the
controller got confused when the DDBs got corrupted.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Ed Chim of Adaptec informs us that the DDB registers need to be zeroed at
initialization time and that some SCB initializations need to happen even if
we don't use the SCB.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
The vmalloc() blob holding the sequencer firmware wasn't being released at
module unload time, which resulted in a memory leak.
Signed-off-by: Alexis Bruemmer <alexisb@us.ibm.com>
Acked-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Now that task aborts and device port resets are done by the EH, we can
remove all the code that set up workqueues and such and simply call
sas_task_abort and let libsas figure things out.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
sas_task_abort() should simply abort the upper-level SCSI command and wait
until the error handler to send the actual ABORT TASK command. By
deferring things to the EH we simplify the concurrency coordination and
eliminate some race conditions. Note that sas_task_abort has a few hooks
to handle libsas internal commands properly too.
Also rename do_sas_task_abort to __sas_task_abort just in case we really
want to abort the task *right now* and we don't have a scsi_cmnd attached
to the command. This is a hook for libata internal commands to abort.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
When a SAS LLDD needs to request a device port reset, it needs to have all
commands aborted before it can reset the port. Since commands are put on
the EH's list in the order that they were queued, the LLDD can set a "need
reset" flag in the last task to be aborted so that the EH can reset the
port after all commands are aborted.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
This flag is no longer necessary because we push tasks to be aborted into
the EH as soon as we possibly can, and let the SCSI EH code take care of
the coordination for which this flag was used.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
In this driver, TMF_QUERY_TASK translates to QUERY_SSP_TASK. The
sequencer, it seems, is perfectly happy sending us a SSP response, which
this function promptly "converts" into TMF_RESP_FUNC_FAILED. This leads to
the SAS EH making bad decisions based on bad data, so we should not perform
the conversion in this case.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Magic number cleanup.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
The aic94xx module has a parameter that looks like it should set
lldd_max_execute_num in the sas_ha, but it never sets this value. Either
we should set it or remove the parameter. This allows us to enable task
collector mode for this driver, though it is still off by default.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
If we use task collector mode, we can end up destroying the task collector
thread before we release the ports, which is bad if a port release causes
a disk I/O (such as cache flushing).
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Every so often, a scsi_cmnd will time out, and the libsas timeout handler
will discover that the scsi_cmnd does not have a sas_task attached to it.
This can happen in two cases: (1) the scsi_cmnd actually made it through
libsas to the HBA and is now going through scsi_done, or (2) the
scsi_cmnd has been held up (host lock, slab alloc, etc) and libsas has
not yet attached a sas_task. In both cases, it is safe to ask SCSI for
more time to process the command via EH_RESET_TIMER; we cannot blindly
return EH_HANDLED because if (2) happens, we could end up calling
scsi_done while another CPU is heading towards sas_queuecommand, which
causes slab corruption when sas_task_done updates the freed scsi_cmnd.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
