aboutsummaryrefslogtreecommitdiff
path: root/drivers/serial
AgeCommit message (Collapse)Author
2006-10-04[PATCH] atmel_serial: Fix roundoff error in atmel_console_get_optionsHaavard Skinnemoen
The atmel_console_get_options() function initializes the baud, parity and bits settings from the actual hardware setup, in case it has been initialized by a e.g. boot loader. The baud rate, however, is not necessarily exactly equal to one of the standard baud rates (115200, etc.) This means that the baud rate calculated by this function may be slightly higher or slightly lower than one of the standard baud rates. If the baud rate is slightly lower than the target, this causes problems when uart_set_option() tries to match the detected baud rate against the standard baud rate, as it will always select a baud rate that is lower or equal to the target rate. For example if the detected baud rate is slightly lower than 115200, usart_set_options() will select 57600. This patch fixes the problem by subtracting 1 from the value in BRGR when calculating the baud rate. The detected baud rate will thus always be higher than the nearest standard baud rate, and uart_set_options() will end up doing the right thing. Tested on ATSTK1000 and AT91RM9200-EK boards. Both are broken without this patch. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Acked-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-04[PATCH] atmel_serial: Support AVR32Haavard Skinnemoen
Make CONFIG_SERIAL_ATMEL selectable on AVR32 and #ifdef out some ARM- specific code in the driver. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Acked-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-04[PATCH] atmel_serial: Pass fixed register mappings through platform_dataHaavard Skinnemoen
In order to initialize the serial console early, the atmel_serial driver had to do a hack where it compared the physical address of the port with an address known to be permanently mapped, and used it as a virtual address. This got around the limitation that ioremap() isn't always available when the console is being initalized. This patch removes that hack and replaces it with a new "regs" field in struct atmel_uart_data that the board-specific code can initialize to a fixed virtual mapping for platform devices where this is possible. It also initializes the DBGU's regs field with the address the driver used to check against. On AVR32, the "regs" field is initialized from the physical base address when this it can be accessed through a permanently 1:1 mapped segment, i.e. the P4 segment. If regs is NULL, the console initialization is delayed until the "real" driver is up and running and ioremap() can be used. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Acked-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-04[PATCH] atmel_serial: Rename at91_register_uart_fnsHaavard Skinnemoen
Rename at91_register_uart_fns and associated structs and variables to make it consistent with the atmel_ prefix used by the rest of the driver. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Acked-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-04[PATCH] serial: Rename PORT_AT91 -> PORT_ATMELHaavard Skinnemoen
The at91_serial driver can be used with both AT32 and AT91 devices from Atmel and has therefore been renamed atmel_serial. The only thing left is to rename PORT_AT91 PORT_ATMEL. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Acked-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-04[PATCH] at91_serial -> atmel_serial: Internal namesHaavard Skinnemoen
Prefix all internal functions and variables with atmel_ instead of at91_. The at91_register_uart_fns() stuff is left as is since I can't find any actual users of it. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Acked-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-04[PATCH] at91_serial -> atmel_serial: Public definitionsHaavard Skinnemoen
Rename the following public definitions: * AT91_NR_UART -> ATMEL_MAX_UART * struct at91_uart_data -> struct atmel_uart_data * at91_default_console_device -> atmel_default_console_device Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Acked-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-04[PATCH] at91_serial -> atmel_serial: Platform device nameHaavard Skinnemoen
Rename the "at91_usart" platform driver "atmel_usart" and update platform devices accordingly. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Acked-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-04[PATCH] at91_serial -> atmel_serial: Kconfig symbolsHaavard Skinnemoen
Rename the following Kconfig symbols: * CONFIG_SERIAL_AT91 -> CONFIG_SERIAL_ATMEL * CONFIG_SERIAL_AT91_CONSOLE -> CONFIG_SERIAL_ATMEL_CONSOLE * CONFIG_SERIAL_AT91_TTYAT -> CONFIG_SERIAL_ATMEL_TTYAT Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Acked-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-04[PATCH] at91_serial -> atmel_serial: at91_serial.cHaavard Skinnemoen
Rename at91_serial.c atmel_serial.c Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Acked-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-04[PATCH] at91_serial -> atmel_serial: at91rm9200_usart.hHaavard Skinnemoen
Move include/asm/arch/at91rm9200_usart.h into drivers/serial and rename it atmel_usart.h. Also delete AVR32's version of this file. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Acked-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-04Merge master.kernel.org:/pub/scm/linux/kernel/git/davej/confighLinus Torvalds
* master.kernel.org:/pub/scm/linux/kernel/git/davej/configh: Remove all inclusions of <linux/config.h> Manually resolved trivial path conflicts due to removed files in the sound/oss/ subdirectory.
2006-10-04[PARISC] Clean up asm-parisc/serial.hMatthew Wilcox
Russell King pointed out that asm/serial.h is anachronistic and we were misusing BASE_BAUD. So fix BASE_BAUD for PCI 16550 UARTs, move LASI_BASE_BAUD into 8250_gsc, and fix the obsolete comment about reserving serial port slots. Signed-off-by: Matthew Wilcox <matthew@wil.cx> Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
2006-10-04[PARISC] Document that D-class can also use serial_muxCarlos O'Donell
Signed-off-by: Carlos O'Donell <carlos@systemhalted.org> Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
2006-10-04Remove all inclusions of <linux/config.h>Dave Jones
kbuild explicitly includes this at build time. Signed-off-by: Dave Jones <davej@redhat.com>
2006-10-03fix file specification in commentsUwe Zeisberger
Many files include the filename at the beginning, serveral used a wrong one. Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com> Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-10-03Fix several typos in drivers/Matt LaPlante
Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-10-03Merge branch 'devel' of master.kernel.org:/home/rmk/linux-2.6-serialLinus Torvalds
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-serial: (21 commits) [SERIAL] add PNP IDs for FPI based touchscreens [SERIAL] Magic SysRq SAK does nothing on serial consoles [SERIAL] tickle NMI watchdog on serial output. [SERIAL] Fix oops when removing suspended serial port [SERIAL] Fix resume handling bug [SERIAL] Remove wrong asm/serial.h inclusions [SERIAL] CONFIG_PM=n slim: drivers/serial/8250_pci.c [SERIAL] OMAP1510 serial fix for 115200 baud [SERIAL] returning proper error from serial core driver [SERIAL] Make uart_line_info() correctly tell MMIO from I/O port [SERIAL] suspend/resume handlers don't have level arg anymore [SERIAL] 8250 resourse management fixes [SERIAL] serial_cs: Add quirk for brainboxes 2-port RS232 card [SERIAL] serial_cs: handle Nokia multi->single port bodge via config quirk [SERIAL] serial_cs: add configuration quirk [SERIAL] serial_cs: Convert Oxford 950 / Possio GCC wakeup quirk [SERIAL] serial_cs: convert IBM post-init handling to a quirk [SERIAL] serial_cs: allow wildcarded quirks [SERIAL] serial_cs: convert multi-port table to quirk table [SERIAL] serial_cs: Use clean up multiport card detection ...
2006-10-03Merge git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpcLinus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (29 commits) [POWERPC] Fix rheap alignment problem [POWERPC] Use check_legacy_ioport() for ISAPnP [POWERPC] Avoid NULL pointer in gpio1_interrupt [POWERPC] Enable generic rtc hook for the MPC8349 mITX [POWERPC] Add powerpc get/set_rtc_time interface to new generic rtc class [POWERPC] Create a "wrapper" script and use it in arch/powerpc/boot [POWERPC] fix spin lock nesting in hvc_iseries [POWERPC] EEH failure to mark pci slot as frozen. [POWERPC] update powerpc defconfig files after libata kconfig breakage [POWERPC] enable sysrq in pmac32_defconfig [POWERPC] UPIO_TSI cleanup [POWERPC] rewrite mkprep and mkbugboot in sane C [POWERPC] maple/pci iomem annotations [POWERPC] powerpc oprofile __user annotations [POWERPC] cell spufs iomem annotations [POWERPC] NULL noise removal: spufs [POWERPC] ppc math-emu needs -fno-builtin-fabs for math.c and fabs.c [POWERPC] update mpc8349_itx_defconfig and remove some debug settings [POWERPC] Always call cede in pseries dedicated idle loop [POWERPC] Fix loop logic in irq_alloc_virt() ...
2006-10-02[PATCH] const struct tty_operationsJeff Dike
As part of an SMP cleanliness pass over UML, I consted a bunch of structures in order to not have to document their locking. One of these structures was a struct tty_operations. In order to const it in UML without introducing compiler complaints, the declaration of tty_set_operations needs to be changed, and then all of its callers need to be fixed. This patch declares all struct tty_operations in the tree as const. In all cases, they are static and used only as input to tty_set_operations. As an extra check, I ran an i386 allyesconfig build which produced no extra warnings. 53 drivers are affected. I checked the history of a bunch of them, and in most cases, there have been only a handful of maintenance changes in the last six months. serial_core.c was the busiest one that I looked at. Signed-off-by: Jeff Dike <jdike@addtoit.com> Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-01[SERIAL] add PNP IDs for FPI based touchscreensMatthew Garrett
The Compaq TC1000 and Fujitsu Stylistic range of tablet machines use touchscreens from FPI. These are implemented as serial interfaces, generally exposed in the ACPIPNP information on the system. This patch adds them to the 8250_pnp driver tables, avoiding the need to mess around with setserial to set them up. I haven't been able to confirm what FUJ02B5, FUJ02BA and FUJ02BB are. FUJ02B1 refers to the controller for the system hotkeys. FUJ02BC appears to be the last in the range - after this, they moved to Wacom-based systems. Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01[SERIAL] tickle NMI watchdog on serial output.Dave Jones
Serial is _slow_ sometimes. So slow, that the NMI watchdog kicks in. NMI Watchdog detected LOCKUP on CPU2CPU 2 Modules linked in: loop usb_storage md5 ipv6 parport_pc lp parport autofs4 i2c_dev i2c_core rfcomm l2cap bluetooth sunrpc pcdPid: 3138, comm: gpm Not tainted 2.6.11-1.1290_FC4smp RIP: 0010:[<ffffffff80273b8a>] <ffffffff80273b8a>{serial_in+106} RSP: 0018:ffff81003afc3d50 EFLAGS: 00000002 RAX: 0000000000000020 RBX: 0000000000000020 RCX: 0000000000000000 RDX: 00000000000003fd RSI: 0000000000000005 RDI: ffffffff804dcd60 RBP: 00000000000024fc R08: 000000000000000a R09: 0000000000000033 R10: ffff81001beb7c20 R11: 0000000000000020 R12: ffffffff804dcd60 R13: ffffffff804ade76 R14: 000000000000002b R15: 000000000000002c FS: 00002aaaaaac4920(0000) GS:ffffffff804fca00(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: 00002aaaaabcb000 CR3: 000000003c0d0000 CR4: 00000000000006e0 Process gpm (pid: 3138, threadinfo ffff81003afc2000, task ffff81003eb63780) Stack: ffffffff80275f2e 0000000000000000 ffffffff80448380 0000000000007d6b 000000000000002c fffffffffffffbbf 0000000000000292 0000000000008000 ffffffff80138e8c 0000000000007d97 Call Trace:<ffffffff80275f2e>{serial8250_console_write+270} <ffffffff80138e8c>{__call_console_drivers+76} <ffffffff8013914b>{release_console_sem+315} <ffffffff80260325>{con_open+149} <ffffffff80254e99>{tty_open+537} <ffffffff80192713>{chrdev_open+387} <ffffffff80188824>{dentry_open+260} <ffffffff80188994>{filp_open+68} <ffffffff80187b73>{get_unused_fd+227} <ffffffff80188a6c>{sys_open+76} <ffffffff8010ebc6>{tracesys+209} Code: 0f b6 c0 c3 66 90 41 57 49 89 f7 41 56 41 be 00 01 00 00 41 console shuts up ... I initially did the patch below a year ago for the Fedora kernel, and have been keeping it up to date since. I recently got the same thing happening on a vanilla kernel, so figured it was time to repost this. Signed-off-by: Dave Jones <davej@redhat.com> Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01[SERIAL] Fix oops when removing suspended serial portRussell King
A serial card might have been removed when the system is resumed. This results in a suspended port being shut down, which results in the ports shutdown method being called twice in a row. This causes BUGs. Avoid this by tracking the suspended state separately from the initialised state. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01[SERIAL] Fix resume handling bugRussell King
Unfortunately, pcmcia_dev_present() returns false when a device is suspended, so checking this on resume does not work too well. Omit this test. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01[SERIAL] CONFIG_PM=n slim: drivers/serial/8250_pci.cAlexey Dobriyan
Remove some code which is unneeded if CONFIG_PM=n. Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01[SERIAL] OMAP1510 serial fix for 115200 baudJonathan McDowell
The patch below is necessary for 115200 baud on an OMAP1510 internal UART. It's been in the linux-omap tree for some time and with it applied to a vanilla Linus git tree the serial console on the Amstrad Delta (which is OMAP1510 based and whose initial bootloader runs at 115200) works fine (it doesn't without it). Signed-off-by: Jonathan McDowell <noodles@earth.li> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01[SERIAL] returning proper error from serial core driverRam Gupta
Fix the issue of returning 0 even in case of error from uart_set_info function. Now it returns the error EBUSY when it can not set new port. Signed-off-by: Ram Gupta <r.gupta@astronautics.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01[SERIAL] Make uart_line_info() correctly tell MMIO from I/O portSergei Shtylyov
/proc/tty/driver/serial incorrectly claims that UARTs having iotype of UPIO_MEM32, UPIO_AU, or UPIO_TSI are I/O mapped. Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01[SERIAL] suspend/resume handlers don't have level arg anymoreSergei Shtylyov
8250.c and serial_txx9.c port suspend/resume handler still have this obsolete argument documented... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01[SERIAL] 8250 resourse management fixesSergei Shtylyov
I think register ranges obviously need to be claimed/released for all UARTs including those with UPIO_MEM32 and UPIO_TSI iotype. Also, serial8250_request_rsa_resources() returns false positives with UPIO_MEM32, UPIO_AU, and UPIO_TSI iotype -- I don't think this makes any sense. Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01[SERIAL] serial_cs: Add quirk for brainboxes 2-port RS232 cardRussell King
Mauro Ziliani reports that this card has a higher clock rate. Rather than tweak the 8250 driver to handle this, add a quirk to pass the correct clock rate to the driver. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01[SERIAL] serial_cs: handle Nokia multi->single port bodge via config quirkRussell King
According to the existing code, Nokia only make single-port cards, but are detected as multi-port cards. Handle this in roughly the same way via the config quirk - forcing it to be a real single port card (info->multi=0) changes the way we allocate the IO memory, which might stop the card working. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01[SERIAL] serial_cs: add configuration quirkRussell King
Add a quirk primerily to handle tweaks to the link->conf structure, eg as required for Socket cards. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01[SERIAL] serial_cs: Convert Oxford 950 / Possio GCC wakeup quirkRussell King
Move the Oxford Semi OX950 / Possio GCC wakeup handling to a quirk wakeup handler. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01[SERIAL] serial_cs: convert IBM post-init handling to a quirkRussell King
Move IBM quirk handling into its own quirk entry. Note that doing quirk handling after we've registered the ports is racy, but since I don't know if moving this will have an undesired effect, it's probably better to leave where it is. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01[SERIAL] serial_cs: allow wildcarded quirksRussell King
Some quirks we will introduce next apply to (eg) all cards of one manufacturer. Therefore, we need a way to list these in the quirk table - use ~0 - this is not a possible device ID value. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01[SERIAL] serial_cs: convert multi-port table to quirk tableRussell King
- rename multi_id table to serial_quirk / quirks[] - use named initialisers - store a pointer to the quirk table in the serial_info structure so we can use the quirk table entry later. - apply multi-port quirk after the multi-port guessing code, but only if it's != -1. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01[SERIAL] serial_cs: Use clean up multiport card detectionRussell King
- Use ARRAY_SIZE() instead of home grown based version. - use parse->manfid.card rather than le16_to_cpu(buf[1]) - manfid.card is already converted to this format. - use info->prodid in subsequent tests rather than parse->manfid.card. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01[SERIAL] Remove m32r_sio dependency on asm/serial.hRussell King
m32r_sio re-uses a custom defined BASE_BAUD from asm/serial.h, and replaces SERIAL_PORT_DFNS with its own driver private copy. Since asm/serial.h is supposed to define 8250-based ports using these symbols, this isn't a sane idea. Hence, eliminate asm/serial.h from m32r_sio.c. Acked-by: Hirokazu Takata <takata@linux-m32r.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01[PATCH] ioremap balanced with iounmap for drivers/serial/sunsu.cAmol Lad
ioremap must be balanced by an iounmap and failing to do so can result in a memory leak. Signed-off-by: Amol Lad <amol@verismonetworks.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: David S. Miller <davem@sunset.davemloft.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-01[PATCH] ioremap balanced with iounmap for drivers/serial/mux.cAmol Lad
ioremap must be balanced by an iounmap and failing to do so can result in a memory leak. Signed-off-by: Amol Lad <amol@verismonetworks.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-01[PATCH] ioremap balanced with iounmap for drivers/serial/mpsc.cAmol Lad
ioremap must be balanced by an iounmap and failing to do so can result in a memory leak. Signed-off-by: Amol Lad <amol@verismonetworks.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Mark A. Greer <mgreer@mvista.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-01[PATCH] ioremap balanced with iounmap for drivers/serial/mpc52xx_uart.cAmol Lad
ioremap must be balanced by an iounmap and failing to do so can result in a memory leak. Signed-off-by: Amol Lad <amol@verismonetworks.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-01[PATCH] ioremap balanced with iounmap for drivers/serial/ip22zilog.cAmol Lad
ioremap must be balanced by an iounmap and failing to do so can result in a memory leak. Signed-off-by: Amol Lad <amol@verismonetworks.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-01[PATCH] ioremap balanced with iounmap for drivers/serial/ioc4_serial.cAmol Lad
ioremap must be balanced by an iounmap and failing to do so can result in a memory leak. Signed-off-by: Amol Lad <amol@verismonetworks.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Brent Casavant <bcasavan@sgi.com> Cc: Pat Gefre <pfg@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-01[PATCH] ioremap balanced with iounmap for drivers/serial/8250_gsc.cAmol Lad
ioremap must be balanced by an iounmap and failing to do so can result in a memory leak. Signed-off-by: Amol Lad <amol@verismonetworks.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-01[PATCH] ioremap balanced with iounmap for drivers/serial/8250_acorn,cAmol Lad
ioremap must be balanced by an iounmap and failing to do so can result in a memory leak. Signed-off-by: Amol Lad <amol@verismonetworks.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-09-29[SERIAL] sunzilog: Mark sunzilog_init_hw as __devinit.David S. Miller
Signed-off-by: David S. Miller <davem@davemloft.net>
2006-09-29[PATCH] fix serial/amba-pl011.c console KconfigPeter Korsgaard
Fix the Kconfig entry for console on AMBA PL011 to match the code. Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-09-28Merge branch 'devel' of master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (130 commits) [ARM] 3856/1: Add clocksource for Intel IXP4xx platforms [ARM] 3855/1: Add generic time support [ARM] 3873/1: S3C24XX: Add irq_chip names [ARM] 3872/1: S3C24XX: Apply consistant tabbing to irq_chips [ARM] 3871/1: S3C24XX: Fix ordering of EINT4..23 [ARM] nommu: confirms the CR_V bit in nommu mode [ARM] nommu: abort handler fixup for !CPU_CP15_MMU cores. [ARM] 3870/1: AT91: Start removing static memory mappings [ARM] 3869/1: AT91: NAND support for DK and KB9202 boards [ARM] 3868/1: AT91 hardware header update [ARM] 3867/1: AT91 GPIO update [ARM] 3866/1: AT91 clock update [ARM] 3865/1: AT91RM9200 header updates [ARM] 3862/2: S3C2410 - add basic power management support for AML M5900 series [ARM] kthread: switch arch/arm/kernel/apm.c [ARM] Off-by-one in arch/arm/common/icst* [ARM] 3864/1: Refactore sharpsl_pm [ARM] 3863/1: Add Locomo SPI Device [ARM] 3847/2: Convert LOMOMO to use struct device for GPIOs [ARM] Use CPU_CACHE_* where possible in asm/cacheflush.h ...