aboutsummaryrefslogtreecommitdiff
path: root/drivers/serial
AgeCommit message (Collapse)Author
2007-03-23[PATCH] add Fujitsu Siemens Tablet PC devices to 8250_pnp.cDanny Kukawka
Adds device ids of two Fujitsu Siemens Tablet PCs to pnp_dev_table Signed-off-by: Danny Kukawka <dkukawka@suse.de> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-03-14serial: Fix sh-sci break interrupt/sysrq handling.Paul Mundt
The sh-sci sci_br_interrupt() handler was failing to call in to uart_handle_break(), which was something that only the SH-3 path was doing, fix that up. Additionally, SUPPORT_SYSRQ seems to have moved down too far, move it back to the top so uart_handle_break() and friends aren't no-ops. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-03-08[PATCH] 2.6 Altix: console fix for CONFIG_DEBUG_SHIRQ usagePat Gefre
The sn console driver was snagged by the use of CONFIG_DEBUG_SHIRQ! The request_irq() immediate call to the interrupt handler caused another attempt to lock the port lock - deadlock. This is a patch to fix that. Signed-off-by: Patrick Gefre <pfg@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-03-06[PATCH] m68knommu: fix work queues in mcfserial.c driverGreg Ungerer
Fix work queue code to support new model. Signed-off-by: Greg Ungerer <gerg@uclinux.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-03-06[PATCH] m68knommu: set GPIO lines for serial ports on 5282 in mcfserial.cGreg Ungerer
For the Freescale M5282 ColdFire, Port UA Pin Assignment Register should set to UART mode. Patch submitted by David Wu <davidwu@arcturusnetworks.com>. Signed-off-by: Greg Ungerer <gerg@uclinux.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-03-05[PATCH] dz: remove struct pt_regs referencesMaciej W. Rozycki
Remove remaining references to saved registers now that uart_handle_sysrq_char() does not want them. Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-26Merge master.kernel.org:/pub/scm/linux/kernel/git/kyle/parisc-2.6Linus Torvalds
* master.kernel.org:/pub/scm/linux/kernel/git/kyle/parisc-2.6: (78 commits) [PARISC] Use symbolic last syscall in __NR_Linux_syscalls [PARISC] Add missing statfs64 and fstatfs64 syscalls Revert "[PARISC] Optimize TLB flush on SMP systems" [PARISC] Compat signal fixes for 64-bit parisc [PARISC] Reorder syscalls to match unistd.h Revert "[PATCH] make kernel/signal.c:kill_proc_info() static" [PARISC] fix sys_rt_sigqueueinfo [PARISC] fix section mismatch warnings in harmony sound driver [PARISC] do not export get_register/set_register [PARISC] add ENTRY()/ENDPROC() and simplify assembly of HP/UX emulation code [PARISC] convert to use CONFIG_64BIT instead of __LP64__ [PARISC] use CONFIG_64BIT instead of __LP64__ [PARISC] add ASM_EXCEPTIONTABLE_ENTRY() macro [PARISC] more ENTRY(), ENDPROC(), END() conversions [PARISC] fix ENTRY() and ENDPROC() for 64bit-parisc [PARISC] Fixes /proc/cpuinfo cache output on B160L [PARISC] implement standard ENTRY(), END() and ENDPROC() [PARISC] kill ENTRY_SYS_CPUS [PARISC] clean up debugging printks in smp.c [PARISC] factor syscall_restart code out of do_signal ... Fix conflict in include/linux/sched.h due to kill_proc_info() being made publicly available to PARISC again.
2007-02-22[SERIAL] serial_txx9 driver updateAtsushi Nemoto
* Use platform_device. * Fix and cleanup suspend/resume/initialization codes. Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2007-02-20[PATCH] 8250: Fix GCC4 signed/unsigned mismatch warningThomas Koeller
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-19Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (117 commits) [ARM] 4058/2: iop32x: set ->broken_parity_status on n2100 onboard r8169 ports [ARM] 4140/1: AACI stability add ac97 timeout and retries [ARM] 4139/1: AACI record support [ARM] 4138/1: AACI: multiple channel support for IRQ handling [ARM] 4211/1: Provide a defconfig for ns9xxx [ARM] 4210/1: base for new machine type "NetSilicon NS9360" [ARM] 4222/1: S3C2443: Remove reference to missing S3C2443_PM [ARM] 4221/1: S3C2443: DMA support [ARM] 4220/1: S3C24XX: DMA system initialised from sysdev [ARM] 4219/1: S3C2443: DMA source definitions [ARM] 4218/1: S3C2412: fix CONFIG_CPU_S3C2412_ONLY wrt to S3C2443 [ARM] 4217/1: S3C24XX: remove the dma channel show at startup [ARM] 4090/2: avoid clash between PXA and SA1111 defines [ARM] 4216/1: add .gitignore entries for ARM specific files [ARM] 4214/2: S3C2410: Add Armzone QT2410 [ARM] 4215/1: s3c2410 usb device: per-platform vbus_draw [ARM] 4213/1: S3C2410 - Update definition of ADCTSC_XY_PST [ARM] 4098/1: ARM: rtc_lock only used with rtc_cmos [ARM] 4137/1: Add kexec support [ARM] 4201/1: SMP barriers pair needed for the secondary boot process ... Fix up conflict due to typedef removal in sound/arm/aaci.h
2007-02-19Merge git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpcLinus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (34 commits) [POWERPC] 86xx: Cleaned up platform dts files [POWERPC] 85xx: Renamed MPC8568 MDS board code to match other boards [POWERPC] 85xx: Cleaning up machine probing [POWERPC] QE: clean up ucc_slow.c and ucc_fast.c [POWERPC] 85xx: Cleaned up platform dts files [POWERPC] 83xx: Renamed MPC8323 MDS dts and defconfig to match other boards [POWERPC] 83xx: Updated and renamed MPC8360PB to MPC836x MDS [POWERPC] 83xx: Use of_platform_bus_probe to setup QE devices [POWERPC] 83xx: use default value of loops_per_jiffy [POWERPC] 83xx: Remove obsolete setting of ROOT_DEV. [POWERPC] 83xx: Cleaning up machine probing and board initcalls [POWERPC] Dispose irq mapping when done in mpc52xx_serial.c [POWERPC] 86xx: Add missing of_node_put() in mpc86xx_hpcn_init_irq(). [POWERPC] 8[56]xx: Remove obsolete setting of ROOT_DEV for 85xx and 86xx platforms. [POWERPC] pseries: Enabling auto poweron after power is restored. [POWERPC] use winbond libata instead of ide driver for pseries CD drives [POWERPC] powerpc: remove references to the obsolete linux,platform property [POWERPC] add of_get_mac_address and update fsl_soc.c to use it [POWERPC] 83xx: Cleaned up 83xx platform dts files [POWERPC] Fix bug with early ioremap and 64k pages ...
2007-02-17Merge AT91, EP93xx, General devel, PXA, S3C, V6+ and Xscale treesRussell King
2007-02-17[POWERPC] Dispose irq mapping when done in mpc52xx_serial.cSylvain Munaut
Signed-off-by: Sylvain Munaut <tnt@246tNt.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-02-17Merge branch 'parisc' from /home/kyle/repos/parisc-2.6.gitKyle McMartin
Conflicts: arch/parisc/hpux/sys_hpux.c arch/parisc/mm/ioremap.c
2007-02-16serial: Add PCMCIA IDs for Quatech DSP-100 dual RS232 adapter.Sergei Organov
Add PCMCIA IDs for Quatech DSP-100 dual RS232 adapter. Signed-off-by: Sergei Organov <osv@javad.com> Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-16[POWERPC] Fix compile failure in cpm_uart_cpm2Paul Gortmaker
Fix bug that exists in kernel.org since 2.6.17rc4 - compiles fail if CONFIG_SERIAL_CPM_SMC is defined. Tested on a board using SMC1 console. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-02-14[PATCH] remove many unneeded #includes of sched.hTim Schmielau
After Al Viro (finally) succeeded in removing the sched.h #include in module.h recently, it makes sense again to remove other superfluous sched.h includes. There are quite a lot of files which include it but don't actually need anything defined in there. Presumably these includes were once needed for macros that used to live in sched.h, but moved to other header files in the course of cleaning it up. To ease the pain, this time I did not fiddle with any header files and only removed #includes from .c-files, which tend to cause less trouble. Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha, arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig, allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all configs in arch/arm/configs on arm. I also checked that no new warnings were introduced by the patch (actually, some warnings are removed that were emitted by unnecessarily included header files). Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de> Acked-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-14[PATCH] PNX8550 UART driverVitaly Wool
Add UART support for PNX8330/8550/8950 Philips MIPS-based SoCs. Signed-off-by: Vitaly Wool <vitalywool@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-14[PATCH] serial: replace kmalloc+memset with kzallocBurman Yan
Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-14[PATCH] serial: make sure UART is powered up when dumping MCTRL statusGeorge G. Davis
Since serial devices are powered down when not in use and some of those devices cannot be accessed when powered down, we need to enable power around calls to get_mcrtl() when dumping port state via uart_line_info(). This resolves hangs observed on some machines while reading serial device registers when a port is powered off. Signed-off-by: George G. Davis <gdavis@mvista.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-14[PATCH] serial: trivial code flow simplificationBjorn Helgaas
Return failure immediately, so we don't have to test it twice. Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Cc: Adam Belay <ambx1@neo.rr.com> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-14[PATCH] 8250 UART backup timerAlex Williamson
The patch below works around a minor bug found in the UART of the remote management card used in many HP ia64 and parisc servers (aka the Diva UARTs). The problem is that the UART does not reassert the THRE interrupt if it has been previously cleared and the IIR THRI bit is re-enabled. This can produce a very annoying failure mode when used as a serial console, allowing a boot/reboot to hang indefinitely until an RX interrupt kicks it into working again (ie. an unattended reboot could stall). To solve this problem, a backup timer is introduced that runs alongside the standard interrupt driven mechanism. This timer wakes up periodically, checks for a hang condition and gets characters moving again. This backup mechanism is only enabled if the UART is detected as having this problem, so systems without these UARTs will have no additional overhead. This version of the patch incorporates previous comments from Pavel and removes races in the bug detection code. The test is now done before the irq linking to prevent races with interrupt handler clearing the THRE interrupt. Short delays and syncs are also added to ensure the device is able to update register state before the result is tested. Aristeu says: this was tested on the following HP machines and solved the problem: rx2600, rx2620, rx1600 and rx1620s. hpa says: I have seen this same bug in soft UART IP from "a major vendor." Signed-off-by: Alex Williamson <alex.williamson@hp.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Russell King <rmk@arm.linux.org.uk> Acked-by: Aristeu Sergio Rozanski Filho <aris@cathedrallabs.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-14[POWERPC] Open Firmware serial port driverArnd Bergmann
This can be used for serial ports that are connected to an OF platform bus but are not autodetected by the lecacy serial support. It will automatically take over devices that come from the legacy serial detection, which usually is only one device. In some cases, rtas may be set up to use the serial port in the firmware, which allows easier debugging before probing the serial ports. In this case, the "used-by-rtas" property must be set by the firmware. This patch also adds code to the legacy serial driver to check for this. Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-02-13[POWERPC] Fixup mp5200 drivers to match device tree changesGrant Likely
Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-02-12[PATCH] atmel_serial: Use __raw I/O register accessHaavard Skinnemoen
Access to chip-internal registers should always be native-endian. This is especially important for AVR32 since it's a big-endian architecture and the non-raw readl() and writel() macros are defined to do little-endian accesses. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Acked-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-11[PATCH] serial: support for new boardMatthias Fuchs
Add support for the CPCI-ASIO4 quad port CompactPCI UART board from electronic system design gmbh. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-11[PATCH] Perle multimodem card (PCI-RAS) detectionThomas Hoehn
Get the Perle quad-modem PCI card (PCI-RAS4) detected by serial driver. It may also get the PCI-RAS8 running, but can't guarantee as I didn't had one for testing. Signed-off-by: Thomas Hoehn <thomas.hoehn@avocent.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-11[PATCH] serial: serial_txx9 driver updateAtsushi Nemoto
Update the serial_txx9 driver. * Configurable manumum port number. (SERIAL_TXX9_NR_UARTS) * Remove some code which is unneeded if CONFIG_PM=n. * Use PCI_DEVICE() for pci device id table and make it const. * Do not include <asm/irq.h> Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-11[PATCH] Char: tty_wakeup cleanupJiri Slaby
tty_wakeup cleanup - remove wake_up_interruptible(&tty->write_wait) surrounding tty_wakup(tty); - substitute tty->ldisc.write_wakeup(tty) + wake_up() by tty_wakeup(tty); Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Acked-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-11[PATCH] IOC3/IOC4: PCI mem space resourcesBrent Casavant
The SGI IOC3 and IOC4 PCI devices implement memory space apertures, not I/O space apertures. Use the appropriate region management functions. Signed-off-by: Brent Casavant <bcasavan@sgi.com> Cc: Pat Gefre <pfg@sgi.com> Cc: Stanislaw Skowronek <skylark@linux-mips.org> Cc: Brent Casavant <bcasavan@sgi.com> Acked-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-11[ARM] amba-pl010: add reference to ep93xx to Kconfig help entryLennert Buytenhek
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-02-11[ARM] i.MX serial: fix IRQ allocationPavel Pisa
If RTS interrupt is caused by RTS senzing logic inside i.MX UART module the IRQ type cannot be set. It applies only for interrupts going through GPIO layer. The problem has been noticed by Konstantin Kletschke some time ago. No IRQF_TRIGGER set_type function for IRQ 26 (MPU) I would not change type to fixed 0, because it could be possible to use different GPIO MX1 pin for RTS in the theory. On the other hand it is only for documentation purposes now, because RTS read code would have to be adjusted in such case. Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-02-11[ARM] i.MX serial: fix tx buffer overflowsSascha Hauer
Fix occasional tx buffer overflows in the i.MX serial driver which came from the fact that space in the buffer was checked after sending the first byte. Also, fifosize is 32 bytes, not 8. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-02-09[PATCH] drivers/serial NULL noise removalAl Viro
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-08[ARM] 4151/1: AT91 / AVR32: Move at91_pdc.h to linux/atmel_pdc.hAndrew Victor
The Atmel AT91 and AVR32 processor architectures share many of the same peripherals. The PDC (Peripheral Data Controller) registers are also implemented within in a number of the on-chip peripherals (eg, USART, MMC, SPI, SSC, etc). In a attempt not to duplicate the register definitions in each peripheral, or in each architecture, the at91_pdc.h header in asm-arm/arch-at91 and asm-avr32/arch-at32ap has been replaced with linux/atmel_pdc.h. The definitions have also been renamed from AT91_PDC_* to ATMEL_PDC_*, and the drivers updated accordingly. Original patch from Nicolas Ferre. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-02-07Merge branch 'linux-2.6'Paul Mackerras
2007-02-07[POWERPC] Fix kernel build errors for mpc8272ads and mpc8560adsVitaly Bordug
Recent update of asm-powerpc/io.h caused cpm-related stuff to break in the current kernel. Current patch fixes it, as well as other inconsistencies expressed, that do not permit targets from working properly: - Updated dts with a chosen node with interrupt controller, - fixed messed device IDs among CPM2 SoC devices, - corrected odd header name and fixed type in defines, - Added 82xx subdir to the powerpc/platforms Makefile, missed during initial commit, - new solely-powerpc header file for 8260 family (was using one from arch/ppc, this one cleaned up from the extra stuff), in fact for now a placeholder to get the board-specific includes for stuff not yet capable to live with devicetree peeks only - Fixed couple of misprints in reference mpc8272 dts. Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-02-07[POWERPC] cpm_uart: OF-related fix for CPM1Vitaly Bordug
This makes cpm uart able to work using OF-passed parameters in case of CPM stuff (found on most mpc8xx reference and custom boards). The idea is to keep ppc stuff working yet making it able to be used for powerpc. Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-01-24[ARM] Fix AMBA serial drivers for non-first serial portsRussell King
Using console=ttyAM1 or console=ttyAMA1 resulted in an oops during boot due to trying to drive the console before that port had been registered. Fix this by checking whether the port is present before allowing console setup to proceed. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-01-24[ARM] 4088/1: AT91: Unbalanced IRQ in serial driver suspend/resumeAndrew Victor
This patch fixes the unbalanced calls to enable_irq_wake() and disable_irq_wake() in the AT91 (and AVR32) serial driver. It should resolve these kernel messages: Unbalanced IRQ x wake disable BUG: warning at kernel/irq/manage.c:167/set_irq_wake() Original patch from Marc Pignat. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-01-24[ARM] 4086/1: AT91: Whitespace cleanupAndrew Victor
A couple of whitespace cleanups, mainly in the AT91 header files. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-01-11[PATCH] x86-64: modpost add more symbols to whitelist pattern2Vivek Goyal
o MODPOST generates warning for i386 if compiled with CONFIG_RELOCATABLE=y and serial console support is enabled. o Serial console setup function, serial8250_console_setup(), is a non __init function and it calls functions which are of type __init(). (uart_parse_options() and uart_set_options()). Assuming, setup will be called during init time, changing serial8250_console_setup() to __init. o Adding one more pattern to modpost whitelist. Console drivers might have *_console structures containing references to setup functions which can be of __init type. Don't generate warnings for those. WARNING: vmlinux - Section mismatch: reference to .init.text: from .data between 'serial8250_console' (at offset 0xc05a33d8) and 'serial8250_reg' Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com> Signed-off-by: Andi Kleen <ak@suse.de> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Andi Kleen <ak@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org>
2007-01-09[POWERPC] Fix mpc52xx serial driver to work for arch/ppc againGrant Likely
The mpc52xx_uart_of_enumerate() function was added when adding 52xx support to arch/powerpc, but it must not be called for arch/ppc. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-12-31[SPARC64]: Fix of_iounmap() region release.David S. Miller
We need to pass in the resource otherwise we cannot release the region properly. We must know whether it is an I/O or MEM resource. Spotted by Eric Brower. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-12-22[PATCH] serial/uartlite: Only enable port if request_port succeededPeter Korsgaard
The uartlite driver used to always enable the port even if request_port failed causing havoc. This patch fixes it. Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-13[PATCH] Add support for Korenix 16C950-based PCI cardsRussell King
This adds initial support to 8250-pci for the Korenix Jetcard PCI serial cards. The JC12xx cards are standard RS232-based serial cards utilising the Oxford 16C950 device. The JC14xx are RS422/RS485-based cards, but in order for these to be supported natively, we will need additional tweaks to the 8250 layers so we can specify some values for the 950's registers. Hence, these two entries are commented out. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-12Merge git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivialLinus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: Fix inotify maintainers entry Fix typo in new debug options. Jon needs a new shift key. fs: Convert kmalloc() + memset() to kzalloc() in fs/. configfs.h: Remove dead macro definitions. kconfig: Standardize "depends" -> "depends on" in Kconfig files e100: replace kmalloc with kcalloc um: replace kmalloc+memset with kzalloc fix typo in net/ipv4/ip_fragment.c include/linux/compiler.h: reject gcc 3 < gcc 3.2 Kconfig: fix spelling error in config KALLSYMS help text Remove duplicate "have to" in comment Fix small typo in drivers/serial/icom.c Use consistent casing in help message EXT{2,3,4}_FS: remove outdated part of the help text
2006-12-12kconfig: Standardize "depends" -> "depends on" in Kconfig filesRobert P. J. Day
Standardize the miniscule percentage of occurrences of "depends" in Kconfig files to "depends on", and update kconfig-language.txt to reflect that. Signed-off-by: Robert P. J. Day <rpjday@mindspring.com> Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-12-12Fix small typo in drivers/serial/icom.cThomas Hisch
Signed-off-by: Thomas Hisch <t.hisch@gmail.com> Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-12-12sh: SH-MobileR SH7722 CPU support.Paul Mundt
This adds CPU support for the SH7722. Signed-off-by: Paul Mundt <lethal@linux-sh.org>