aboutsummaryrefslogtreecommitdiff
path: root/drivers/usb/Makefile
AgeCommit message (Collapse)Author
2009-03-24USB: Add platform device support for the ISP1760 USB chipCatalin Marinas
Currently, the driver only supports PCI and PPC_OF but there are boards like ARM RealView where this is a platform device. The patch adds the necessary functions and registration to the isp1760-if.c file and modifies the corresponding Makefile and Kconfig to be able to use this driver even if PCI and PPC_OF are not enabled. Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Cc: Sebastian Siewior <bigeasy@linutronix.de> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-09USB: Correct Makefile to make isp1760 buildableIvan Kuten
Signed-off-by: Ivan Kuten <ivan.kuten@promwad.com> Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-27USB: Driver for Freescale QUICC Engine USB Host ControllerAnton Vorontsov
This patch adds support for the FHCI USB controller, as found in the Freescale MPC836x and MPC832x processors. It can support Full or Low speed modes. Quite a lot the hardware is doing by itself (SOF generation, CRC generation and checking), though scheduling and retransmission is on software's shoulders. This controller does not integrate the root hub, so this driver also fakes one-port hub. External hub is required to support more than one device. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-09-17wusb: add HWA host controller driverInaky Perez-Gonzalez
Add a driver for Wireless USB host controllers connected via USB (a Host Wire Adapter or HWA). Signed-off-by: David Vrabel <david.vrabel@csr.com>
2008-09-17wusb: add the Wireless USB core (build-system)Greg Kroah-Hartman
Add the WUSB build system (Kconfig and Kbuild) files. Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: David Vrabel <david.vrabel@csr.com>
2008-05-02USB: add Cypress c67x00 OTG controller HCD driverPeter Korsgaard
This patch adds HCD support for the Cypress c67x00 family of devices. Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-10-12USB: always visit drivers/usb/misc/Adrian Bunk
Currently, every driver under drivers/usb/misc/ also has to be listed in drivers/usb/Makefile. This has been forgotten more than once, and this patch changes drivers/usb/Makefile to simply always visit drivers/usb/misc/ when building the USB code. Signed-off-by: Adrian Bunk <bunk@kernel.org> Cc: Toralf Förster <toralf.foerster@gmx.de> Acked-by: Satyam Sharma <satyam@infradead.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-10-12USB: Add drivers/usb/misc/iowarrior.c to the MakefileNico Erfurth
This patch adds the new iowarrior module to the Makefile in drivers/usb. Currently the module isn't build unless another driver from usb/misc is selected. Signed-off-by: Nico Erfurth <masta@perlgolf.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-07-30USB: devices misc: Trivial patch to build the IOWARRIOR when it is selected ↵Juergen Beisert
in Kconfig Trivial patch to build the IOWARRIOR when it is selected in Kconfig. Signed-off-by: Juergen Beisert <jbe@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-07-12USB: remove Makefile reference to obsolete OHCI_AT91Robert P. J. Day
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-07-12USB: r8a66597-hcd: host controller driver for R8A66597Yoshihiro Shimoda
I would like to submit Renesas R8A66597 USB HCD driver. R8A66597 is Renesas USB 2.0 host and peripheral combined controller device originally designed for embedded products. As a limitation of this device, it does not support externel hub more than 2 tier, and cannot communicate with a USB device more than 10. Then this device is not compatible with EHCI and/or OHCI, I wrote driver support patch based on sl811 code. This driver has the following unique specifications: - Implement transfer timeout to share one pipe with plural endpoint. - Detach detection of a USB device connected to externel hub. The driver has been tested external hub, usb-hdd, usb-cdrom, usb-speaker, mice, keyboard, and usbtest driver. Signed-off-by : Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-05-09Move USB network drivers to drivers/net/usb.Jeff Garzik
It is preferable to group drivers by usage (net, scsi, ATA, ...) than by bus. When reviewing drivers, the [PCI|USB|PCMCIA|...] maintainer is probably less qualified on networking issues than a networking maintainer. Also, from a practical standpoint, chips often appear on multiple buses, which is why we do not put drivers into drivers/pci/net. Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-08Input: move USB miscellaneous devices under drivers/input/miscDmitry Torokhov
This will allow concentrating all input devices in one place in {menu|x|q}config. Signed-off-by: Dmitry Torokhov <dtor@mail.ru> Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-05-08Input: move USB gamepads under drivers/input/joystickDmitry Torokhov
This will allow concentrating all input devices in one place in {menu|x|q}config. Signed-off-by: Dmitry Torokhov <dtor@mail.ru> Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-05-08Input: move USB touchscreens under drivers/input/touchscreenDmitry Torokhov
This will allow concentrating all input devices in one place in {menu|x|q}config. Signed-off-by: Dmitry Torokhov <dtor@mail.ru> Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-05-08Input: move USB tablets under drivers/input/tabletDmitry Torokhov
This will allow concentrating all input devices in one place in {menu|x|q}config. Signed-off-by: Dmitry Torokhov <dtor@mail.ru> Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-04-30Merge branch 'for-linus' of ↵Linus Torvalds
master.kernel.org:/pub/scm/linux/kernel/git/jikos/hid * 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jikos/hid: (21 commits) USB HID: don't warn on idVendor == 0 USB HID: add 'quirks' module parameter USB HID: add support for dynamically-created quirks USB HID: clarify static quirk handling as squirks USB HID: encapsulate quirk handling into hid-quirks.c USB HID: EMS USBII device needs HID_QUIRK_MULTI_INPUT HID: update copyright and authorship macro HID: introduce proper zeroing of unused bits in output reports USB HID: add support for WiseGroup MP-8800 Quad Joypad USB HID: add FF support for Logitech Force 3D Pro Joystick USB HID: numlock quirk for dell W7658 keyboard USB HID: Logitech MX3000 keyboard needs report descriptor quirk USB HID: extend quirk for Logitech S510 keyboard USB HID: usbkbd/usbmouse - handle errors when registering devices USB HID: add QUIRK_HIDDEV for Belkin Flip KVM HID: enable dead keys on a belkin wireless keyboard USB HID: Thustmaster firestorm dual power v1 support USB HID: specify explicit size for hid_blacklist.quirks USB HID: fix retry & reset logic USB HID: consolidate vendor/product ids ...
2007-04-27USB: remove ancient/broken CRIS hcdDavid Brownell
Remove the old crisv10 HCD ... it can't have built for some time, doesn't even have a Kconfig entry, was the last driver not to have been converted to the "hcd" framework, and considering the usbcore changes since its last patch was merged, has just got to buggy as all get-out. I'm told Axis has a new driver, and will be submitting it soon. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Mikael Starvik <mikael.starvik@axis.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-04-11USB HID: move usbhid code from drivers/usb/input to drivers/hid/usbhidJiri Kosina
Separate usbhid code into dedicated drivers/hid/usbhid directory as discussed previously with Greg, so that it eases maintaineance process. Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-16USB: Driver to charge USB blackberry devicesGreg Kroah-Hartman
A simple driver to turn on the charging capability of a USB BlackBerry device when it is plugged into the machine. It does not bind to the device, so all userspace programs can still sync properly with it. Note, if CONFIG_USB_SUSPEND is enabled, it can play havoc with this device as the power to the port will be shut down. This device id will have to be added to the global blacklist table when it is created. Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-10-17USB: move trancevibrator.c to the proper usb directoryGreg Kroah-Hartman
It's not a input driver, so it doesn't belong in the input directory. Cc: Sam Hocevar <sam@zoy.org> Cc: Dmitry Torokhov <dtor@insightbb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-09-27USB: u132-hcd: host controller driver for ELAN U132 adapterTony Olech
This "u132-hcd" module is one half of the "driver" for ELAN's U132 which is a USB to CardBus OHCI controller adapter. This module needs the "ftdi-elan" module in order to communicate to CardBus OHCI controller inserted into the U132 adapter. When the "ftdi-elan" module detects a supported CardBus OHCI controller in the U132 adapter it loads this "u132-hcd" module. Upon a successful device probe() the single workqueue is started up which does all the processing of commands from the USB core that implement the host controller. The workqueue maintains the urb queues and issues commands via the functions exported by the "ftdi-elan" module. Each such command will result in a callback. Note that the "ftdi-elan" module is a USB client driver. Note that this "u132-hcd" module is a (cut-down OHCI) host controller. Thus we have a topology with the parent of a host controller being a USB client! This really stresses the USB subsystem semaphore/mutex handling in the module removal. Signed-off-by: Tony Olech <tony.olech@elandigitalsystems.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-09-27USB: ftdi-elan: client driver for ELAN Uxxx adaptersTony Olech
This "ftdi-elan" module is one half of the "driver" for ELAN's Uxxx series adapters which are USB to PCMCIA CardBus adapters. Currently only the U132 adapter is available and it's module is called "u132-hcd". When the USB hot plug subsystem detects a Uxxx series adapter it should load this module. Upon a successful device probe() the jtag device file interface is created and the status workqueue started up. The jtag device file interface exists for the purpose of updating the firmware in the Uxxx series adapter, but as yet it had never been used. The status workqueue initializes the Uxxx and then sits there polling the Uxxx until a supported PCMCIA CardBus device is detected it will start the command and respond workqueues and then load the module that handles the device. This will initially be only the u132-hcd module. The status workqueue then just polls the Uxxx looking for card ejects. The command and respond workqueues implement a command sequencer for communicating with the firmware on the other side of the FTDI chip in the Uxxx. This "ftdi-elan" module exports some functions to interface with the sequencer. Note that this module is a USB client driver. Note that the "u132-hcd" module is a (cut-down OHCI) host controller. Thus we have a topology with the parent of a host controller being a USB client! This really stresses the USB subsystem semaphore/mutex handling in the module removal. Signed-off-by: Tony Olech <tony.olech@elandigitalsystems.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-09-27USB: add PlayStation 2 Trance Vibrator driverSam Hocevar
This patch is a driver for the PlayStation 2 specific Trance Vibrator device. The only thing that device can do is vibrate at various speeds. Signed-off-by: Sam Hocevar <sam@zoy.org> Cc: Pete Zaitcev <zaitcev@redhat.com> Cc: Luiz Fernando N. Capitulino" <lcapitulino@mandriva.com.br> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-09-27USB: Add ADU support for Ontrak ADU devicesSteven Haigh
This patch adds support for Ontrak ADU USB devices. Fixed for printk issues by Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Steven Haigh <netwiz@crc.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-07-12[PATCH] USB: rename Cypress CY7C63xxx driver to proper name and fix up some ↵Oliver Bock
tiny things This is a new driver for the Cypress CY7C63xxx mirco controller series. It currently supports the pre-programmed CYC63001A-PC by AK Modul-Bus GmbH. It's based on a kernel 2.4 driver (cyport) by Marcus Maul which I ported to kernel 2.6 using sysfs. I intend to support more controllers of this family (and more features) as soon as I get hold of the required IDs etc. Please see the source code's header for more information. Signed-off-by: Oliver Bock <o.bock@fh-wolfenbuettel.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-21[PATCH] USB: new driver for Cypress CY7C63xxx mirco controllersOliver Bock
This is a new driver for the Cypress CY7C63xxx mirco controller series. It currently supports the pre-programmed CYC63001A-PC by AK Modul-Bus GmbH. It's based on a kernel 2.4 driver (cyport) by Marcus Maul which I ported to kernel 2.6 using sysfs. I intend to support more controllers of this family (and more features) as soon as I get hold of the required IDs etc. Please see the source code's header for more information. Signed-off-by: Oliver Bock <o.bock@fh-wolfenbuettel.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-21[PATCH] Driver for Apple Cinema Displayakpm@osdl.org
This is a driver to control the brightness of an Apple Cinema Display over USB. It updates the local brightness value if the user presses a button on the display. Signed-off-by: Michael Hanselmann <linux-kernel@hansmi.ch> Cc: Oliver Neukum <oliver@neukum.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-03-25V4L/DVB (3599a): Move drivers/usb/media to drivers/media/videoMauro Carvalho Chehab
Because of historic reasons, there are two separate directories with V4L stuff. Most drivers are located at driver/media/video. However, some code for USB Webcams were inserted under drivers/usb/media. This makes difficult for module authors to know were things should be. Also, makes Kconfig menu confusing for normal users. This patch moves all V4L content under drivers/usb/media to drivers/media/video, and fixes Kconfig/Makefile entries. Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2006-03-20[PATCH] USB: add support for OCHI on AT91rm9200Andrew Victor
This adds support for OHCI on AT91rm9200 based boards. Possibly of interest here is the way this uses <linux/clk.h> to gate clocks on/off during system pm state transitions. That's typical for non-PCI systems. Some can go further; Mini-A host side connectors enable ID-pin sensing. From: Andrew Victor <andrew@sanpeople.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-03-20[PATCH] USB: remove OBSOLETE_OSS_USB_DRIVER driversAdrian Bunk
This patch removes the obsolete USB_MIDI and USB_AUDIO drivers. Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-03-20[PATCH] USB: Add ZC0301 Video4Linux2 driverLuca Risolia
This patch adds a Video4Linux2 driver for ZC0301 Image Processor and Control Chip. Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-31[PATCH] USB: Add ET61X[12]51 Video4Linux2 driverLuca Risolia
This patch adds a Video4Linux2 driver giving support to ET61X151 and ET61X251 PC Camera Controllers made by Etoms Electronics. Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-04[PATCH] USB: drivers/usb/storage/libusualPete Zaitcev
This patch adds a shim driver libusual, which routes devices between usb-storage and ub according to the common table, based on unusual_devs.h. The help and example syntax is in Kconfig. Signed-off-by: Pete Zaitcev <zaitcev@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-10-28[PATCH] USB: delete the bluetty driverGreg Kroah-Hartman
We have a real Bluetooth system in Linux, lets finally delete this driver as no one is using it (and if they are, they are using a closed source bluetooth stack, which I can't support anyway.) Marcel, you owe me a beer :) Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-10-28[PATCH] USB: move handoff codeDavid Brownell
This moves the PCI quirk handling for USB host controllers from the PCI directory to the USB directory. Follow-on patches will need to: (a) merge these copies with the originals in the HCD reset methods. they don't wholly agree, despite doing the very same thing; and (b) eventually change it so "usb-handoff" is the default, to help get more robust USB/BIOS/input/... interactions. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> drivers/Makefile | 2 drivers/pci/quirks.c | 253 --------------------------------------- drivers/usb/Makefile | 1 drivers/usb/host/Makefile | 5 drivers/usb/host/pci-quirks.c | 272 ++++++++++++++++++++++++++++++++++++++++++ 5 files changed, 280 insertions(+), 253 deletions(-)
2005-07-12[PATCH] USB: add ldusb driverMichael Hund
The following driver provides complete interrupt-in and interrupt-out reports (raw data) to a user program. Until now it uses the HIDIOCGDEVINFO ioctl call, because I don't know better :-(. Perhaps, it will be ok for you - and I will be happy, if you assign 8 minor numbers. I have tested it in several environments and it works very well for me. However, it has a problem with two or more devices at the same hub, if the two or more devices need 1 ms interrupt-in transfers. Unfortunately more than one interrupt-in transfer every ms isn't possible (ehci driver?). This is why the min_interrupt_in_interval and min_interrupt_out_interval are increased to 2 ms (see the corresponding module parameters). This way, I can use two devices simultaneously at the same hub. Signed-off-by: Michael Hund <mhund@ld-didactic.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-07-12[PATCH] USB: SiS USB Makefile fixesThomas Winischhofer
although 2.6.12 now contains the sisusb driver, it failes to build this driver due to a missing patch of the Makefile. From: Thomas Winischhofer <thomas@winischhofer.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-06-27Merge master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6Linus Torvalds
2005-06-27[PATCH] USB: Add isp116x-hcd USB host controller driverOlav Kongas
This patch provides an "isp116x-hcd" driver for Philips' ISP1160/ISP1161 USB host controllers. The driver: - is relatively small, meant for use on embedded platforms. - runs usbtests 1-14 without problems for days. - has been in use by 6-7 different people on ARM and PPC platforms, running a range of devices including USB hubs. - supports suspend/resume of both the platform device and the root hub; supports remote wakeup of the root hub (but NOT the platform device) by USB devices. - does NOT support ISO transfers (nobody has asked for them). - is PIO-only. Signed-off-by: Olav Kongas <ok@artecdesign.ee> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-06-06Input: add driver for Acecad Flair USB tabletsStephane VOLTZ
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2005-04-16Linux-2.6.12-rc2Linus Torvalds
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!