| Age | Commit message (Collapse) | Author |
|---|
|
* git://git.infradead.org/mtd-2.6:
mtd: nand: fix build failure and incorrect return from omap_wait()
mtd: Use BLOCK_NIL consistently in NFTL/INFTL
mtd: m25p80 timeout too short for worst-case m25p16 devices
mtd: atmel_nand: Fix typo s/parititions/partitions/
mtd: cmdlineparts: Use 64-bit format when printing a debug message.
mtd: maps: Remove BUS_ID_SIZE from integrator_flash
jffs2: fix another potential leak on error path in scan.c
|
|
This fixes kernel.org bug #13584. The IOVA code attempted to optimise
the insertion of new ranges into the rbtree, with the unfortunate result
that some ranges just didn't get inserted into the tree at all. Then
those ranges would be handed out more than once, and things kind of go
downhill from there.
Introduced after 2.6.25 by ddf02886cbe665d67ca750750196ea5bf524b10b
("PCI: iova RB tree setup tweak").
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: mark gross <mgross@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
cfq-iosched: remove redundant check for NULL cfqq in cfq_set_request()
blocK: Restore barrier support for md and probably other virtual devices.
block: get rid of queue-private command filter
block: Create bip slabs with embedded integrity vectors
cfq-iosched: get rid of the need for __GFP_NOFAIL in cfq_find_alloc_queue()
cfq-iosched: move cfqq initialization out of cfq_find_alloc_queue()
Trivial typo fixes in Documentation/block/data-integrity.txt.
|
|
* 'for-linus' of git://neil.brown.name/md:
md: use interruptible wait when duration is controlled by userspace.
md/raid5: suspend shouldn't affect read requests.
md: tidy up error paths in md_alloc
md: fix error path when duplicate name is found on md device creation.
md: avoid dereferencing NULL pointer when accessing suspend_* sysfs attributes.
md: Use new topology calls to indicate alignment and I/O sizes
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (31 commits)
Revert "ipv4: arp announce, arp_proxy and windows ip conflict verification"
igb: return PCI_ERS_RESULT_DISCONNECT on permanent error
e1000e: io_error_detected callback should return PCI_ERS_RESULT_DISCONNECT
e1000: return PCI_ERS_RESULT_DISCONNECT on permanent error
e1000: fix unmap bug
igb: fix unmap length bug
ixgbe: fix unmap length bug
ixgbe: Fix link capabilities during adapter resets
ixgbe: Fix device capabilities of 82599 single speed fiber NICs.
ixgbe: Fix SFP log messages
usbnet: Remove private stats structure
usbnet: Use netdev stats structure
smsc95xx: Use netdev stats structure
rndis_host: Use netdev stats structure
net1080: Use netdev stats structure
dm9601: Use netdev stats structure
cdc_eem: Use netdev stats structure
ipv4: Fix fib_trie rebalancing, part 3
bnx2x: Fix the behavior of ethtool when ONBOOT=no
sctp: xmit sctp packet always return no route error
...
|
|
The initial patches to support this through sysfs export were broken
and have been if 0'ed out in any release. So lets just kill the code
and reclaim some space in struct request_queue, if anyone would later
like to fixup the sysfs bits, the git history can easily restore
the removed bits.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
This patch restores stacking ability to the block layer integrity
infrastructure by creating a set of dedicated bip slabs. Each bip slab
has an embedded bio_vec array at the end. This cuts down on memory
allocations and also simplifies the code compared to the original bvec
version. Only the largest bip slab is backed by a mempool. The pool is
contained in the bio_set so stacking drivers can ensure forward
progress.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@carl.(none)>
|
|
User space can set various limits on an md array so that resync waits
when it gets to a certain point, or so that I/O is blocked for a short
while.
When md is waiting against one of these limit, it should use an
interruptible wait so as not to add to the load average, and so are
not to trigger a warning if the wait goes on for too long.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
md allows write to regions on an array to be suspended temporarily.
This allows user-space to participate is aspects of reshape.
In particular, data can be copied with not risk of a race.
We should not be blocking read requests though, so don't.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
PCI drivers that implement the io_error_detected callback should return
PCI_ERS_RESULT_DISCONNECT if the state passed in is
pci_channel_io_perm_failure. This patch fixes the issue for igb.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
on permanent failure
PCI drivers that implement the io_error_detected callback
should return PCI_ERS_RESULT_DISCONNECT if the state
passed in is pci_channel_io_perm_failure. This state is not
checked in many of the network drivers.
This patch fixes the omission in the e1000e driver.
Signed-off-by: Mike Mason <mmlnx@us.ibm.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PCI drivers that implement the io_error_detected callback
should return PCI_ERS_RESULT_DISCONNECT if the state
passed in is pci_channel_io_perm_failure. This state is
not checked in many of the network drivers.
The patch fixes the omission in the e1000 driver.
Based on Mike Mason's similar patch for e1000e.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
CC: Mike Mason <mmlnx@us.ibm.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
as reported by kerneloops.org
[ 121.781161] ------------[ cut here ]------------
[ 121.781171] WARNING: at lib/dma-debug.c:793 check_unmap+0x14e/0x577()
[ 121.781173] Hardware name: S5520HC
[ 121.781177] e1000 0000:0a:00.0: DMA-API: device driver tries to free DMA
memory it has not allocated [device address=0x00000001d688b0fa] [size=1522
bytes]
[ 121.781180] Modules linked in: e1000 mdio dca [last unloaded: ixgbe]
[ 121.781187] Pid: 4793, comm: bash Tainted: P 2.6.30-master-06161113 #3
[ 121.781190] Call Trace:
[ 121.781195] [<ffffffff8123056f>] ? check_unmap+0x14e/0x577
[ 121.781201] [<ffffffff81057a19>] warn_slowpath_common+0x77/0x8f
[ 121.781205] [<ffffffff81057ae1>] warn_slowpath_fmt+0x9f/0xa1
[ 121.781212] [<ffffffff81477ce2>] ? _spin_lock_irqsave+0x3f/0x49
[ 121.781216] [<ffffffff8122fa97>] ? get_hash_bucket+0x28/0x33
[ 121.781220] [<ffffffff8123056f>] check_unmap+0x14e/0x577
[ 121.781225] [<ffffffff810e4f48>] ? check_bytes_and_report+0x38/0xcb
[ 121.781230] [<ffffffff81230bbf>] debug_dma_unmap_page+0x80/0x92
[ 121.781234] [<ffffffff8122e549>] ? unmap_single+0x1a/0x4e
[ 121.781239] [<ffffffff813901e1>] ? __kfree_skb+0x74/0x78
[ 121.781250] [<ffffffffa00662ef>] pci_unmap_single+0x64/0x6d [e1000]
[ 121.781259] [<ffffffffa0066344>] e1000_clean_rx_ring+0x4c/0xbf [e1000]
[ 121.781268] [<ffffffffa00663df>] e1000_clean_all_rx_rings+0x28/0x36 [e1000]
[ 121.781277] [<ffffffffa0067464>] e1000_down+0x138/0x141 [e1000]
[ 121.781286] [<ffffffffa00681c2>] __e1000_shutdown+0x6b/0x198 [e1000]
[ 121.781296] [<ffffffffa0068405>] e1000_suspend+0x17/0x50 [e1000]
[ 121.781301] [<ffffffff81237665>] pci_legacy_suspend+0x3b/0xbe
[ 121.781305] [<ffffffff81237bc6>] pci_pm_suspend+0x3e/0xf1
[ 121.781310] [<ffffffff812eaf1c>] pm_op+0x57/0xde
[ 121.781314] [<ffffffff812eb444>] dpm_suspend_start+0x31e/0x470
[ 121.781319] [<ffffffff810877da>] suspend_devices_and_enter+0x3e/0x1a2
[ 121.781323] [<ffffffff81087a0f>] enter_state+0xd1/0x127
[ 121.781327] [<ffffffff8108717a>] state_store+0xa7/0xc9
[ 121.781332] [<ffffffff81221843>] kobj_attr_store+0x17/0x19
[ 121.781336] [<ffffffff8113c01e>] sysfs_write_file+0xe5/0x121
[ 121.781341] [<ffffffff810ed165>] vfs_write+0xab/0x105
[ 121.781344] [<ffffffff810ed279>] sys_write+0x47/0x6d
[ 121.781349] [<ffffffff81027aab>] system_call_fastpath+0x16/0x1b
[ 121.781352] ---[ end trace 97bacaaac2ed7786 ]---
Fix is to correctly zero out internal ->dma value when unmapping
and make sure never to unmap unless there specifically was a mapping done.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
driver was mixing NET_IP_ALIGN count bytes in map/unmap calls
unevenly. Only map the bytes that the hardware might dma into
also fix unmap related bug where ->dma was not being cleared
after unmap
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch addresses three WARN_ON statements from DMA-API debug code
ixgbe is mapping more than it unmaps, reduce the length of the map call and
remove the "used once" local variable.
found by Joerg Roedel <joerg.roedel@amd.com> in 2.6.30, so is a candidate
for -stable.
in addition, fix missing ->dma = 0 after unmap to prevent double free with
pci_unmap_single
and lastly, don't unmap (half) pages that aren't mapped.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adapter link advertisement capabilities were not persistent during
adapter resets. While configuring multispeed fiber link check for
phy autoneg_advertised settings before overwriting with default
link capabilities
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
82599 single speed fiber modules only support 10G/Full. Return
proper device capabilities while querrying the adapter and error
while changing device advertisement/speed/duplex capabilities.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We had a wide range of log messages for the same sort of SFP
failure. This patch makes them all more similar and less
confusing along with converting them to dev_err.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that netdev has its own stats structure we should use that
instead.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that netdev has its own stats structure we should use that
instead.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that netdev has its own stats structure we should use that
instead.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that netdev has its own stats structure we should use that
instead.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that netdev has its own stats structure we should use that
instead.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that netdev has its own stats structure we should use that
instead.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As the recent bug in md_alloc showed, having a single exit path for
unlocking and putting is a good idea. So restructure md_alloc to have
a single mutex_unlock and mddev_put, and use gotos where necessary.
Found-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
When an md device is created by name (rather than number) we need to
check that the name is not already in use. If this check finds a
duplicate, we return an error without dropping the lock or freeing
the newly create mddev.
This patch fixes that.
Cc: stable@kernel.org
Found-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm:
dm table: fix blk_stack_limits arg to use bytes not sectors
dm exception store: really fix type lookup
|
|
A crappy macro prevents us unlocking on a fail path.
Expand the macro and unlock appropriatelly.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Make sure we do not actually request the RTC IRQ until the device driver
is fully ready to handle and process any interrupt. This way a spurious
interrupt won't crash the system (which may happen if the bootloader was
poking the RTC right before booting Linux).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Block writes require 64 byte alignment. Since block writes could be used
with SGRAM or WRAM also refine the memory type detection to check for
either type before deciding to use the 64 byte alignment.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Tested-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Apparently HP OmniBook 500's BIOS doesn't like the way atyfb reprograms
the hardware. The BIOS will simply hang after a reboot. Fix the problem
by restoring the hardware to it's original state on reboot.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Cc: Mikulas Patocka <mpatocka@redhat.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
IRQ handling is wrong for any GPIO >= PL061_GPIO_NR.
Fix this by implementing and using a proper .to_irq method.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Note that IRQ has not been initialized when kmalloc() fails.
Also, use DECLARE_BITMAP() to make the code clearer.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Bugfix to spi_bitbang infrastructure: make sure to always set transfer
parameters on the first pass through the message's per-transfer loop.
This can matter with drivers that replace the per-word or per-buffer
transfer primitives, on busses with multiple SPI devices.
Previously, this could have started messages using the settings left after
previous messages. The problem was observed when a high speed chip
(m25p80 type flash) was running very slowly because a low speed device
(avr8 microcontroller) had previously used the bus. Similar faults could
have driven the low speed device too fast, or used an unexpected word
size.
Acked-by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add a mutex to avoid a circular locking problem between the mm layer
semaphore and fbdev ioctl mutex through the fb_mmap() call.
Also, add mutex to all places where smem_start and smem_len fields change
so the mutex inside the fb_mmap() is actually used. Changing of these
fields before calling the framebuffer_register() are not mutexed.
This is 2.6.31 material. It removes one lockdep (fb_mmap() and
register_framebuffer()) but there is still another one (fb_release() and
register_framebuffer()). It also cleans up handling of the smem_start and
smem_len fields used by mutexed section of the fb_mmap().
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add a new spi_master.flags word listing constraints relevant to that
controller. Define the first constraint bit: a half duplex restriction.
Include that constraint in the OMAP1 MicroWire controller driver.
Have the mmc_spi host be the first customer of this flag. Its coding
relies heavily on full duplex transfers, so it must fail when the
underlying controller driver won't perform them.
(The spi_write_then_read routine could use it too: use the
temporarily-withdrawn full-duplex speedup unless this flag is set, in
which case the existing code applies. Similarly, any spi_master
implementing only SPI_3WIRE should set the flag.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add two new spi_device.mode bits to accomodate more protocol options, and
pass them through to usermode drivers:
* SPI_NO_CS ... a second 3-wire variant, where the chipselect
line is removed instead of a data line; transfers are still
full duplex.
This obviously has STRONG protocol implications since the
chipselect transitions can't be used to synchronize state
transitions with the SPI master.
* SPI_READY ... defines open drain signal that's pulled low
to pause the clock. This defines a 5-wire variant (normal
4-wire SPI plus READY) and two 4-wire variants (READY plus
each of the 3-wire flavors).
Such hardware flow control can be a big win. There are ADC
converters and flash chips that expose READY signals, but not
many host controllers support it today.
The spi_bitbang code should be changed to use SPI_NO_CS instead of its
current nonportable hack. That's a mode most hardware can easily support
(unlike SPI_READY).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: "Paulraj, Sandeep" <s-paulraj@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Since some new MPC85xx SOCs support DDR3 memory now, so add DDR3 memory
type for MPC85xx EDAC.
Signed-off-by: Yang Shi <yang.shi@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add support for the PCI-Express NetMos 9901 Multi-IO card.
0001:06:00.0 Serial controller [0700]: NetMos Technology Device [9710:9901] (prog-if 02 [16550])
Subsystem: Device [a000:1000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 65
Region 0: I/O ports at 0030 [size=8]
Region 1: Memory at 80105000 (32-bit, non-prefetchable) [size=4K]
Region 4: Memory at 80104000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: serial
Kernel modules: 8250_pci
0001:06:00.1 Serial controller [0700]: NetMos Technology Device [9710:9901] (prog-if 02 [16550])
Subsystem: Device [a000:1000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 65
Region 0: I/O ports at 0020 [size=8]
Region 1: Memory at 80103000 (32-bit, non-prefetchable) [size=4K]
Region 4: Memory at 80102000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: serial
Kernel modules: 8250_pci
0001:06:00.2 Parallel controller [0701]: NetMos Technology Device [9710:9901] (prog-if 03 [IEEE1284])
Subsystem: Device [a000:2000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 65
Region 0: I/O ports at 0010 [size=8]
Region 1: I/O ports at <unassigned>
Region 2: Memory at 80101000 (32-bit, non-prefetchable) [size=4K]
Region 4: Memory at 80100000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: parport_pc
Kernel modules: parport_pc
[ 16.760181] PCI parallel port detected: 416c:0100, I/O at 0x812010(0x0), IRQ 65
[ 16.760225] parport0: PC-style at 0x812010, irq 65 [PCSPP,TRISTATE,EPP]
[ 16.851842] serial 0001:06:00.0: enabling device (0004 -> 0007)
[ 16.883776] 0001:06:00.0: ttyS0 at I/O 0x812030 (irq = 65) is a ST16650V2
[ 16.893832] serial 0001:06:00.1: enabling device (0004 -> 0007)
[ 16.926537] 0001:06:00.1: ttyS1 at I/O 0x812020 (irq = 65) is a ST16650V2
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Change the eventfd interface to de-couple the eventfd memory context, from
the file pointer instance.
Without such change, there is no clean way to racely free handle the
POLLHUP event sent when the last instance of the file* goes away. Also,
now the internal eventfd APIs are using the eventfd context instead of the
file*.
This patch is required by KVM's IRQfd code, which is still under
development.
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Gregory Haskins <ghaskins@novell.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Cc: Avi Kivity <avi@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If we try to modify one of the md/ sysfs files
suspend_lo or suspend_hi
when the array is not active, we dereference a NULL.
Protect against that.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Switch MD over to the new disk_stack_limits() function which checks for
aligment and adjusts preferred I/O sizes when stacking.
Also indicate preferred I/O sizes where applicable.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
This is the same fix as commit
7959ea254ed18faee41160b1c50b3c9664735967 ("bnx2: Fix the behavior of
ethtool when ONBOOT=no"), but for bnx2x:
--------------------
When configure in ifcfg-eth* is ONBOOT=no,
the behavior of ethtool command is wrong.
# grep ONBOOT /etc/sysconfig/network-scripts/ifcfg-eth2
ONBOOT=no
# ethtool eth2 | tail -n1
Link detected: yes
I think "Link detected" should be "no".
--------------------
Signed-off-by: Naohiro Ooiwa <nooiwa@miraclelinux.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The offset passed to blk_stack_limits() must be in bytes not sectors.
Fixes false warnings like the following:
device-mapper: table: 254:1: target device sda6 is misaligned
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Reported-by: Frans Pop <elendil@planet.nl>
Tested-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Fix exception store name handling.
We need to reference exception store by zero terminated string.
Fixes regression introduced in commit f6bd4eb73cdf2a5bf954e497972842f39cabb7e3
Cc: Yi Yang <yi.y.yang@intel.com>
Cc: Jonathan Brassow <jbrassow@redhat.com>
Cc: stable@kernel.org
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide-2.6:
ide: memory overrun in ide_get_identity_ioctl() on big endian machines using ioctl HDIO_OBSOLETE_IDENTITY
ide: fix resume for CONFIG_BLK_DEV_IDEACPI=y
ide-cd: handle fragmented packet commands gracefully
ide: always kill the whole request on error
ide: fix ide_kill_rq() for special ide-{floppy,tape} driver requests
|
|
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ioctl HDIO_OBSOLETE_IDENTITY
This patch fixes a memory overrun in function ide_get_identity_ioctl() which
chooses the size of a memory buffer depending on the ioctl command that led
to the function call, however, passes that buffer to a function which needs the
buffer size to be always chosen unconditionally.
Due to conditional compilation the memory overrun can only happen on big endian
machines. The error can be triggered using ioctl HDIO_OBSOLETE_IDENTITY. Usage
of ioctl HDIO_GET_IDENTITY is safe.
Signed-off-by: Christian Engelmayer <christian.engelmayer@frequentis.com>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 2f0d0fd2a605666d38e290c5c0d2907484352dc4 ("ide-acpi: cleanup
do_drive_get_GTF()") didn't account for the lack of hwif->acpidata
check in generic_ide_suspend() [ indirect user of do_drive_get_GTF()
through ide_acpi_exec_tfs() ] resulting in broken resume when ACPI
support is enabled but ACPI data is unavailable.
Fix it by adding ide_port_acpi() helper for checking if port needs
ACPI handling and cleaning generic_ide_{suspend,resume}() to use it
instead of hiding hwif->acpidata and ide_noacpi checks in IDE ACPI
helpers (this should help in preventing similar bugs in the future).
While at it:
- kill superfluous debugging printks in ide_acpi_{get,push}_timing()
Reported-and-tested-by: Etienne Basset <etienne.basset@numericable.fr>
Also-reported-and-tested-by: Jeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight:
backlight: Fix tdo24m crash on kmalloc
|
