aboutsummaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2010-01-20spi: update MSIOF includesMagnus Damm
Update the MSIOF driver to remove the architecture speficic spi header file and add err.h. This makes the driver compile on non-SH architectures. Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-01-20spi/dw_spi: refine the IRQ mode working flowFeng Tang
Now dw_spi core fully supports 3 transfer modes: pure polling, DMA and IRQ mode. IRQ mode will use the FIFO half empty as the IRQ trigger, so each interface driver need set the fifo_len, so that core driver can handle it properly Signed-off-by: Feng Tang <feng.tang@intel.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-01-20spi/dw_spi: add a missed dw_spi_remove_host() in exit sequenceFeng Tang
Signed-off-by: Feng Tang <feng.tang@intel.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-01-20spi/dw_spi: bug fix in wait_till_not_busy()Feng Tang
Make the driver wait at least for 1 jiffie before issuing the warning, no matter what HZ is set to Signed-off-by: Feng Tang <feng.tang@intel.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-01-20spi/s3c64xx: Add new parameter to cs callbackJassi Brar
Since most of the chip-selects are simply going to be like gpio_set_value, it would do good to have the same callback type so that it could simply be made to point at gpio_set_value. Signed-off-by: Jassi Brar <jassi.brar@samsung.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-01-20spi/s3c64xx: Include moved headerJassi Brar
Header for platform specific stuff has been rename to include the SoC type. Include the new header instead. Signed-off-by: Jassi Brar <jassi.brar@samsung.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-01-20spi/s3c64xx: Check before mem-region releaseJassi Brar
Add precautionary check before releasing memory region. Signed-off-by: Jassi Brar <jassi.brar@samsung.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-01-20spi/s3c64xx: Move src_clk to local driver dataJassi Brar
The pointer to SPI rate source clock had better be the member of driver local data structure rather than platform specific. Also, remove definitions of variable 'sci' that are rendered useless as a consequence. Signed-off-by: Jassi Brar <jassi.brar@samsung.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-01-20spi/s3c64xx: Differentiate ip and rate clockJassi Brar
The instance of SPI clock for controller and that used for generating signals ought to be independently handled. Signed-off-by: Jassi Brar <jassi.brar@samsung.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-01-20spi/s3c64xx: Rename s3c64xx_spi_cntrlr_infoJassi Brar
Rename 'struct s3c64xx_spi_cntrlr_info' to lesser wordy 'struct s3c64xx_spi_info' Signed-off-by: Jassi Brar <jassi.brar@samsung.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-01-20spi/mpc8xxx: don't check platform_get_irq's return value against zeroUwe Kleine-König
platform_get_irq returns -ENXIO on failure, so !irq was probably always true. Make irq a signed variable and compare irq <= 0. Note that a return value of zero is still handled as error even though this could mean irq0. This is a followup to 305b3228f9ff4d59f49e6d34a7034d44ee8ce2f0 that changed the return value of platform_get_irq from 0 to -ENXIO on error. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-01-20spi: Add Freescale/Motorola Coldfire QSPI driverSteven King
Add support for the QSPI controller found some on Freescale/Motorola Coldfire MCUs. Full duplex, active high cs, spi modes 0-3 and word sizes 8-16 bits are supported. The hardware drives the MISO, MOSI and SCLK lines, but the chip selects are managed via GPIO and must be configured by the board code. The QSPI controller has an 80 byte buffer which allows us to transfer up to 16 words at a time. For transfers longer than 16 words, we split the buffer in half so we can update in one half while the controller is operating on the other half. Interrupt latencies then ultimately limits our sustained thru-put to something less than half the maximum speed supported by the part. Signed-off-by: Steven King <sfking@fdwdc.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-01-20spi: make Open Firmware device id constantMárton Németh
The match_table field of the struct of_device_id is constant in <linux/of_platform.h> so it is worth to make the initialization data constant. The semantic match that finds this kind of pattern is as follows: (http://coccinelle.lip6.fr/) // <smpl> @r@ disable decl_init,const_decl_init; identifier I1, I2, x; @@ struct I1 { ... const struct I2 *x; ... }; @s@ identifier r.I1, y; identifier r.x, E; @@ struct I1 y = { .x = E, }; @c@ identifier r.I2; identifier s.E; @@ const struct I2 E[] = ... ; @depends on !c@ identifier r.I2; identifier s.E; @@ + const struct I2 E[] = ...; // </smpl> Signed-off-by: Márton Németh <nm127@freemail.hu> Cc: Julia Lawall <julia@diku.dk> Cc: cocci@diku.dk Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-01-20spi: Fix reversed args to time_before() in Freescale stmp driver.Robert P. J. Day
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-01-20spi: Add SPI master driver for DaVinci/DA8xxSandeep Paulraj
This patch adds support for a SPI master driver for the DaVinci series of SOCs Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com> Signed-off-by: Mark A. Greer <mgreer@mvista.com> Signed-off-by: Philby John <pjohn@in.mvista.com> Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-01-12Merge git://git.infradead.org/battery-2.6Linus Torvalds
* git://git.infradead.org/battery-2.6: pmu_battery: Fix battery full reporting
2010-01-12[SCSI] megaraid_sas: remove sysfs poll_mode_io world writeable permissionsBryn M. Reeves
/sys/bus/pci/drivers/megaraid_sas/poll_mode_io defaults to being world-writable, which seems bad (letting any user affect kernel driver behavior). This turns off group and user write permissions, so that on typical production systems only root can write to it. Signed-off-by: Bryn M. Reeves <bmr@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-01-12Merge branch 'for-linus' of git://gitorious.org/linux-omap-dss2/linuxLinus Torvalds
* 'for-linus' of git://gitorious.org/linux-omap-dss2/linux: OMAP: DSS2: OMAPFB: fix crash when panel driver was not loaded OMAP: DSS2: Reject scaling settings when they cannot be supported OMAP: DSS2: Make check-delay-loops consistent OMAP: DSS2: OMAPFB: fix omapfb_free_fbmem() video/omap: add __init/__exit macros to drivers/video/omap/lcd_htcherald.c OMAP: DSS2: Fix compile warning MAINTAINERS: Combine DSS2 and OMAPFB2 into one entry MAINTAINERS: change omapfb maintainer OMAP: OMAPFB: add dummy release function for omapdss OMAP: OMAPFB: fix clk_get for RFBI OMAP: DSS2: RFBI: convert to new kfifo API OMAP: DSS2: Fix crash when panel doesn't define enable_te() OMAP: DSS2: Collect interrupt statistics OMAP: DSS2: DSI: print debug DCS cmd in hex OMAP: DSS2: DSI: fix VC channels in send_short and send_null
2010-01-12lib: Introduce generic list_sort functionDave Chinner
There are two copies of list_sort() in the tree already, one in the DRM code, another in ubifs. Now XFS needs this as well. Create a generic list_sort() function from the ubifs version and convert existing users to it so we don't end up with yet another copy in the tree. Signed-off-by: Dave Chinner <david@fromorbit.com> Acked-by: Dave Airlie <airlied@redhat.com> Acked-by: Artem Bityutskiy <dedekind@infradead.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-01-12Merge branch 'upstream-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev * 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: libata: retry link resume if necessary ata_piix: enable 32bit PIO on SATA piix sata_promise: don't classify overruns as HSM errors
2010-01-12Merge master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds
* master.kernel.org:/home/rmk/linux-2.6-arm: ARM: Ensure ARMv6/7 mm files are built using appropriate assembler options ARM: Fix wrong dmb ARM: 5874/1: serial21285: fix disable_irq-from-interrupt-handler deadlock ARM: 5873/1: ARM: Fix the reset logic for ARM RealView boards ARM: 5872/1: ARM: include needed linux/cpu.h in asm/cpu.h ARM: 5871/1: arch/arm: Fix build failure for lpd7a404_defconfig caused by missing includes ARM: 5870/1: arch/arm: Fix build failure for defconfigs without CONFIG_ISA_DMA_API set ARM: 5868/1: ARM: fix "BUG: using smp_processor_id() in preemptible code" ARM: 5867/1: Update U300 defconfig ARM: 5866/1: arm ptrace: use unsigned types for kernel pt_regs [ARM] pxa: fix strange characters in zaurus gpio .desc ARM: add missing recvmmsg syscall number [ARM] pxa: fix compiler warnings of unused variable 'id' in cpu_is_pxa9*() [ARM] pxa: update pwm_backlight->notify() to include missed 'struct device *' [ARM] pxa: enable L2 if present in XSC3 [ARM] pxa: do not enable L2 after MMU is enabled
2010-01-12Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (56 commits) sky2: Fix oops in sky2_xmit_frame() after TX timeout Documentation/3c509: document ethtool support af_packet: Don't use skb after dev_queue_xmit() vxge: use pci_dma_mapping_error to test return value netfilter: ebtables: enforce CAP_NET_ADMIN e1000e: fix and commonize code for setting the receive address registers e1000e: e1000e_enable_tx_pkt_filtering() returns wrong value e1000e: perform 10/100 adaptive IFS only on parts that support it e1000e: don't accumulate PHY statistics on PHY read failure e1000e: call pci_save_state() after pci_restore_state() netxen: update version to 4.0.72 netxen: fix set mac addr netxen: fix smatch warning netxen: fix tx ring memory leak tcp: update the netstamp_needed counter when cloning sockets TI DaVinci EMAC: Handle emac module clock correctly. dmfe/tulip: Let dmfe handle DM910x except for SPARC on-board chips ixgbe: Fix compiler warning about variable being used uninitialized netfilter: nf_ct_ftp: fix out of bounds read in update_nl_seq() mv643xx_eth: don't include cache padding in rx desc buffer size ... Fix trivial conflict in drivers/scsi/cxgb3i/cxgb3i_offload.c
2010-01-12libata: retry link resume if necessaryTejun Heo
Interestingly, when SIDPR is used in ata_piix, writes to DET in SControl sometimes get ignored leading to detection failure. Update sata_link_resume() such that it reads back SControl after clearing DET and retry if it's not clear. Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: fengxiangjun <fengxiangjun@neusoft.com> Reported-by: Jim Faulkner <jfaulkne@ccs.neu.edu> Cc: stable@kernel.org Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-01-12ata_piix: enable 32bit PIO on SATA piixTejun Heo
Commit 871af1210f13966ab911ed2166e4ab2ce775b99d enabled 32bit PIO for PATA piix but didn't for SATA. There's no reason not to use 32bit PIO on SATA piix. Enable it. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-01-12sata_promise: don't classify overruns as HSM errorsMikael Pettersson
When sata_promise encounters an overrun or underrun error it translates that to a libata AC_ERR_HSM, causing a hard reset. Since over/under-runs were thought to be rare and transient, this action seemed reasonable. Unfortunately it turns out that the controller throws overrun errors when e.g. hal polls a CD or DVD writer containing blank media, causing long sequences of hard resets and retries before EH finally gives up. This patch updates sata_promise to classify over/under-runs as AC_ERR_OTHER instead. This allows libata EH and upper layers to retry or fail the operation as they see fit without the disruption caused by repeated hard resets. This fixes a problem using a DVD-RAM drive with sata_promise, reported by Thomas Schorpp. I also tested it on a DVD-RW drive. Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Tested-by: thomas schorpp <thomas.schorpp@googlemail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-01-12sky2: Fix oops in sky2_xmit_frame() after TX timeoutJarek Poplawski
During TX timeout procedure dev could be awoken too early, e.g. by sky2_complete_tx() called from sky2_down(). Then sky2_xmit_frame() can run while buffers are freed causing an oops. This patch fixes it by adding netif_device_present() test in sky2_tx_complete(). Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=14925 With debugging by: Mike McCormack <mikem@ring3k.org> Reported-by: Berck E. Nash <flyboy@gmail.com> Tested-by: Berck E. Nash <flyboy@gmail.com> Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-12OMAP: DSS2: OMAPFB: fix crash when panel driver was not loadedTomi Valkeinen
If the panel's probe had failed, omapfb would still go on, eventually crashing. A better fix would be to handle each display properly, and leaving just the failed display out. But that is a bigger change. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-01-12OMAP: DSS2: Reject scaling settings when they cannot be supportedVille Syrjälä
If the scaling ratio is below 0.5 video output width can't be identical to the display width. Reject such settings. Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com> Acked-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-01-11Merge branch 'agp-fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/agp-2.6 * 'agp-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/agp-2.6: agp/hp: fail gracefully if we don't find an IOC agp/hp: fixup hp agp after ACPI changes agp: correct missing cleanup on error in agp_add_bridge
2010-01-11Merge branch 'drm-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6 * 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (45 commits) drm/nv04: Fix set_operation software method. drm/nouveau: initialise DMA tracking parameters earlier drm/nouveau: use dma.max rather than pushbuf size for checking GET validity drm/nv04: differentiate between nv04/nv05 drm/nouveau: Fix null deref in nouveau_fence_emit due to deleted fence drm/nv50: prevent a possible ctxprog hang drm/nouveau: have ttm's fault handler called directly drm/nv50: restore correct cache1 get/put address on fifoctx load drm/nouveau: create function for "dealing" with gpu lockup drm/nouveau: remove unused nouveau_channel_idle() function drm/nouveau: fix handling of fbcon colours in 8bpp drm/nv04: Context switching fixes. drm/nouveau: Use the software object for fencing. drm/nouveau: Allocate a per-channel instance of NV_SW. drm/nv50: make the blocksize depend on vram size drm/nouveau: better alignment of bo sizes and use roundup instead of ALIGN drm/nouveau: Don't skip card take down on nv0x. drm/nouveau: Implement nv42-nv43 TV load detection. drm/nouveau: Clean up the nv17-nv4x load detection code a bit. drm/nv50: fix fillrect color ...
2010-01-11Merge branch 'hwmon-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging * 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging: hwmon: Make PCI device ids constant hwmon: (coretemp) Fix TjMax for Atom N450/D410/D510 CPUs hwmon: (k10temp) Blacklist more family 10h processors hwmon: (asus_atk0110) Add debugfs interface hwmon: (asus_atk0110) Refactor interface probe code hwmon: (adt7462) Fix pin 28 monitoring
2010-01-11Merge branch 'omap-fixes-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 * 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (26 commits) OMAP2 clock: dynamically allocate CPUFreq frequency table OMAP clock/CPUFreq: add clk_exit_cpufreq_table() OMAP2xxx OPP: clean up comments in OPP data OMAP2xxx clock: clk2xxx.c doesn't compile if CPUFREQ is enabled OMAP1 clock: remove __initdata from struct clk_functions to prevent crash OMAP1 clock: Add missing clocks for OMAP 7xx OMAP clock: remove incorrect EXPORT_SYMBOL()s OMAP3 clock: Add capability to change rate of dpll4_m5_ck OMAP3 clock: McBSP 2, 3, 4 functional clock parent is PER_96M_FCLK, not CORE_96M_FCLK OMAP3: clock: add clockdomains for UART1 & 2 OMAP2420 IO mapping: move IVA mapping virtual address out of vmalloc space OMAP2xxx IO mapping: mark DSP mappings as being 2420-only ARM: OMAP3: PM: Fix the Invalid CM_CLKSTCTRL reg access. OMAP2: remove duplicated #include omap3: EVM: Choose OMAP_PACKAGE_CBB omap3: Fix booting if package is uninitialized omap3: add missing parentheses omap3: add missing parentheses omap2/3: ZOOM: Correcting key mapping for few keys omap2/3: make serial_in_override() address the right uart port ...
2010-01-11rtc_cmos: convert shutdown to new pnp_driver->shutdownOGAWA Hirofumi
commit abd6633c67925f90775bb74755f9c547e30f1f20 ("pnp: add a shutdown method to pnp drivers") adds shutdown method to bus driver blindly. With it, driver->shutdown is no longer valid. Use pnp_driver->shutdown instead. Addresses http://bugzilla.kernel.org/show_bug.cgi?id=14889 Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp> Reported-by: Malte Schröder <maltesch@gmx.de> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Cc: Bjorn Helgaas <bjorn.helgaas@hp.com> Cc: David Hardeman <david@hardeman.nu> Cc: Dmitry Torokhov <dtor@mail.ru> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Paul Gortmaker <p_gortmaker@yahoo.com> Cc: <stable@kernel.org> [2.6.32.x] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-01-11gpio: adp5588-gpio: new driver for ADP5588 GPIO expandersMichael Hennerich
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-01-11drivers/cpuidle/governors/menu.c: fix undefined reference to `__udivdi3'Stephen Hemminger
menu: use proper 64 bit math The new menu governor is incorrectly doing a 64 bit divide. Compile tested only Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Len Brown <len.brown@intel.com> Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-01-11hwmon: driver for Texas Instruments amc6821 chipTomaz Mertelj
Signed-off-by: <tomaz.mertelj@guest.arnes.si> Cc: Jean Delvare <khali@linux-fr.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-01-11gpiolib: fix poll(2) support reconfigure on sysfs polarity changeJani Nikula
Previously enabled poll(2) support on one edge was never reconfigured when sysfs polarity change was triggered from kernel, because 'struct device *dev' shadowed an earlier definition. Found by sparse, which I should've run much earlier. Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-01-11mmc: allow for MMC v4.4Adrian Hunter
JEDEC eMMC specification version 4.4 (MMCA 4.4) defines Extended CSD structure versions up to 5. Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-01-11mmc_block: fix queue cleanupAdrian Hunter
The main bug was that 'blk_cleanup_queue()' was called while the block device could still be in use, for example, because the card was removed while files were still open. In addition, to be sure that 'mmc_request()' will get called for all new requests (so it can error them out), the queue is emptied during cleanup. This is done after the worker thread is stopped to avoid racing with it. Finally, it is not a device error for this to be happening, so quiet the (sometimes very many) error messages. Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com> Cc: <linux-mmc@vger.kernel.org> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-01-11mmc_block: fix probe error cleanup bugJarkko Lavinen
If mmc_blk_set_blksize() fails mmc_blk_probe() the request queue and its thread have been set up and they need to be shut down properly before putting the disk. Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com> Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com> Cc: <linux-mmc@vger.kernel.org> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-01-11mmc_block: add dev_t initialization checkAnna Lemehova
When a card is removed before mmc_blk_probe() has called add_disk(), then the minor field is uninitialized and has value 0. This caused mmc_blk_put() to always release devidx 0 even if 0 was still in use. Then the next mmc_blk_probe() used the first free idx of 0, which oopses in sysfs, since it is used by another card. Signed-off-by: Anna Lemehova <EXT-Anna.Lemehova@nokia.com> Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com> Cc: <linux-mmc@vger.kernel.org> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-01-11power: fix kernel-doc notationRandy Dunlap
Warning(drivers/base/power/main.c:453): No description found for parameter 'dev' Warning(drivers/base/power/main.c:453): No description found for parameter 'cb' Warning(drivers/base/power/main.c:719): No description found for parameter 'dev' Warning(drivers/base/power/main.c:719): No description found for parameter 'state' Warning(drivers/base/power/main.c:719): No description found for parameter 'cb' Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Cc: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-01-11ARM: 5874/1: serial21285: fix disable_irq-from-interrupt-handler deadlockSimon Kagstrom
The console hangs during bootup when disable_irq is called from the transmit interrupt handler (it will wait forever for it's "own" interrupt in synchronize_irq). Fix by using disable_irq_nosync() instead. Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-01-11OMAP: DSS2: Make check-delay-loops consistentTomi Valkeinen
Loops checking for certain condition were rather inconsistent. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com> Reported-by: Juha Leppanen <juha_motorsportcom@luukku.com>
2010-01-11OMAP: DSS2: OMAPFB: fix omapfb_free_fbmem()Tomi Valkeinen
Fixes bug causing VRFB memory area to be released twice. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com> Reported-by: Eino-Ville Talvala <talvala@stanford.edu>
2010-01-11video/omap: add __init/__exit macros to drivers/video/omap/lcd_htcherald.cPeter Huewe
Trivial patch which adds the __init/__exit macros to the module_init/ module_exit functions of drivers/video/omap/lcd_htcherald.c Please have a look at the small patch and either pull it through your tree, or please ack' it so Jiri can pull it through the trivial tree. Patch against linux-next-tree, 22. Dez 08:38:18 CET 2009 but also present in linus tree. Signed-off-by: Peter Huewe <peterhuewe@gmx.de> Acked-by: Tony Lindgren <tony@atomide.com>
2010-01-11OMAP: DSS2: Fix compile warningVaibhav Hiremath
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com> Acked-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-01-11OMAP: OMAPFB: add dummy release function for omapdssTomi Valkeinen
This should fix: WARNING: at drivers/base/core.c:131 device_release+0x68/0x7c() Device 'omapdss' does not have a release() function, it is broken and must be fixed. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-01-11OMAP: OMAPFB: fix clk_get for RFBITomi Valkeinen
omapfb platform device was still used to get clocks inside rfbi.c Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com> Tested-by: Sergey Lapin <slapin@ossfans.org>
2010-01-11OMAP: DSS2: RFBI: convert to new kfifo APITomi Valkeinen
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-16 00:30:25 +0000