| Age | Commit message (Collapse) | Author |
|---|
|
|
|
1) Forgotten counter incrementation in sis900_rx() in case
it doesn't get memory for skb, that leads to whole interface failure.
Problem is accompanied with messages:
eth0: Memory squeeze,deferring packet.
eth0: NULL pointer encountered in Rx ring, skipping
2) If counter cur_rx overflows and there'll be temporary memory problems
buffer can't be recreated later, when memory IS available.
3) Limit the work in handler to prevent the endless packets processing
if new packets are generated faster then handled.
Signed-off-by: Konstantin Khorenko <khorenko@sw.ru>
Signed-off-by: Vasily Averin <vvs@sw.ru>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
removing executable bits.
|
|
This patch replaces current PowerPC 4xx EMAC driver with
new, re-written from the scratch version. This patch is quite big
(~234K) because there is virtualy 0% of common code between old and
new version.
New driver uses NAPI, it solves stability problems under heavy packet
load and low memory, corrects chip register access and fixes numerous
small bugs I don't even remember now.
This patch has been tested on all supported in 2.6 PPC 4xx boards.
It's been used in production for almost a year now on custom
4xx hardware. PPC32 specific parts are already upstream.
Patch was acked by the current EMAC driver maintainer (Matt Porter). I
will be maintaining this new version.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
--
Kconfig | 72
ibm_emac/Makefile | 13
ibm_emac/ibm_emac.h | 418 +++--
ibm_emac/ibm_emac_core.c | 3414 ++++++++++++++++++++++++----------------------
ibm_emac/ibm_emac_core.h | 313 ++--
ibm_emac/ibm_emac_debug.c | 377 ++---
ibm_emac/ibm_emac_debug.h | 63
ibm_emac/ibm_emac_mal.c | 674 +++++----
ibm_emac/ibm_emac_mal.h | 336 +++-
ibm_emac/ibm_emac_phy.c | 335 ++--
ibm_emac/ibm_emac_phy.h | 105 -
ibm_emac/ibm_emac_rgmii.c | 201 ++
ibm_emac/ibm_emac_rgmii.h | 68
ibm_emac/ibm_emac_tah.c | 111 +
ibm_emac/ibm_emac_tah.h | 96 -
ibm_emac/ibm_emac_zmii.c | 255 +++
ibm_emac/ibm_emac_zmii.h | 114 -
17 files changed, 4114 insertions(+), 2851 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
Under heavy PCI bus load, ports of the DFE-580TX 4-ethernet port board stop
working, with currently no other cure than a powercycle. Here is a tested
fix. By the way, I also fixed some references and attribution.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
|
|
|
|
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
IXDP2x01 systems can be built without PCI network cards, so we should not
require NET_PCI to build CS89x0 on these systems.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
If the interface is not used right away after being probed it wastes
power needlessly. Noted by Holger Schurig.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
Here is a patch that changes the way the MAC filter is computed for the
multicast addresses. The computation is taken from the SiS GPL driver.
This patch is necessary to get IPv6 working.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
Looks like someone used the MII constants instead of the ethtool constants.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
The documentation about s2io is available at
Documentation/networking/s2io.txt.
Signed-off-by: Akinobu Mita <mita@miraclelinux.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
prism54 is leaking information when passing transmits to the firmware.
There is no requirement to adjust the length to >= ETH_ZLEN.
Just pass the skb length (after possible adjustment).
Signed-off-by: Roger While <simrw@sim-basis.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
Some older DL10019 based cards need to setup
the auto-negotiation-advertisement register
to advertise 100Full,100Half,10Full and 10Half.
Signed-off-by: <komurojun-mbn@nifty.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
This patch fixes a bug that happens when the hypervisor can't add a
buffer. The old code wrote IBM_VETH_INVALID_MAP into the free_map
array, so next time the index was used, a ibmveth_assert() caught it and
called BUG(). The patch writes the right value into the free_map array
so that the index can be reused.
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
This patch adds the lockless TX feature to the ibmveth driver. The
hypervisor has its own locking so the only change that is necessary is
to protect the statistics counters.
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
This patch removes the allocation of RX skb's buffers from a workqueue
to be called directly at RX processing time. This change was suggested
by Dave Miller when the driver was starving the RX buffers and
deadlocking under heavy traffic:
> Allocating RX SKBs via tasklet is, IMHO, the worst way to
> do it. It is no surprise that there are starvation cases.
>
> If tasklets or work queues get delayed in any way, you lose,
> and it's very easy for a card to catch up with the driver RX'ing
> packets very fast, no matter how aggressive you make the
> replenishing. By the time you detect that you need to be
> "more aggressive" it is already too late.
> The only pseudo-reliable way is to allocate at RX processing time.
>
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
This patch changes the way the ibmveth driver handles the receive
buffers. The old code mallocs and maps all the buffers in the pools
regardless of MTU size and it also limits the number of buffer pools to
three. This patch makes the driver malloc and map the buffers necessary
to support the current MTU. It also changes the hardcoded names of the
buffer pool number, size, and elements to arrays to make it easier to
change (with the hope of making them runtime parameters in the future).
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
This patch updates dev->trans_start and dev->last_rx so that the ibmveth
driver can be used with the ARP monitor in the bonding driver.
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
Update version and reldate and add more sanity checking to
tg3_set_settings().
Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
Change the ASF heart beat to 5 seconds for faster detection of system
crash. The driver sends the heartbeat every 2 seconds and the ASF
firmware will timeout and reset the device if no heartbeat is received
after 5 seconds. The old scheme of 2 minutes is ineffective.
tg3_write_mem_fast() is added to speed up the IO to send the heartbeat.
When no workaround is needed, it will use direct MMIO to memory space
to write to memory.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
Add complete support for 5714/5715. These chips are very similar to
5780 so the changes are very trivial. A TG3_FLG2_5780_CLASS flag is
added to identify these chips.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
|
|
Manual fixup for trivial "gfp_t" changes.
|
|
git://brick.kernel.dk/data/git/linux-2.6-block
|
|
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Jens Axboe <axboe@suse.de>
|
|
- 100msec sleep is a little excessive, lots of requests can complete
in that timeframe. Use 10msec instead.
- Rename QUEUE_FLAG_BYPASS to QUEUE_FLAG_ELVSWITCH to indicate what
is going on.
Signed-off-by: Jens Axboe <axboe@suse.de>
|
|
This patch reimplements elevator switch. This patch assumes generic
dispatch queue patchset is applied.
* Each request is tagged with REQ_ELVPRIV flag if it has its elevator
private data set.
* Requests which doesn't have REQ_ELVPRIV flag set never enter
iosched. They are always directly back inserted to dispatch queue.
Of course, elevator_put_req_fn is called only for requests which
have its REQ_ELVPRIV set.
* Request queue maintains the current number of requests which have
its elevator data set (elevator_set_req_fn called) in
q->rq->elvpriv.
* If a request queue has QUEUE_FLAG_BYPASS set, elevator private data
is not allocated for new requests.
To switch to another iosched, we set QUEUE_FLAG_BYPASS and wait until
elvpriv goes to zero; then, we attach the new iosched and clears
QUEUE_FLAG_BYPASS. New implementation is much simpler and main code
paths are less cluttered, IMHO.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
|
|
This patch kills max_back_kb handling from elv_dispatch_sort() and
kills max_back_kb field from struct request_queue.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
|
|
Remove last_merge handling from all ioscheds. This patch
removes merging capability of noop iosched.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
Currently, both generic elevator code and specific ioscheds
participate in the management and usage of last_merge. This
and the following patches move last_merge handling into
generic elevator code.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
|
|
This patch updates all four ioscheds to use generic dispatch
queue. There's one behavior change in as-iosched.
* In as-iosched, when force dispatching
(ELEVATOR_INSERT_BACK), batch_data_dir is reset to REQ_SYNC
and changed_batch and new_batch are cleared to zero. This
prevernts AS from doing incorrect update_write_batch after
the forced dispatched requests are finished.
* In cfq-iosched, cfqd->rq_in_driver currently counts the
number of activated (removed) requests to determine
whether queue-kicking is needed and cfq_max_depth has been
reached. With generic dispatch queue, I think counting
the number of dispatched requests would be more appropriate.
* cfq_max_depth can be lowered to 1 again.
Original from Tejun Heo, modified version applied.
Signed-off-by: Jens Axboe <axboe@suse.de>
|
|
Signed-off-by: Jens Axboe <axboe@suse.de>
|
|
- Split elv_dispatch_insert() into two functions
- Rename rq_last_sector() to rq_end_sector()
Signed-off-by: Jens Axboe <axboe@suse.de>
|
|
Implements generic dispatch queue which can replace all
dispatch queues implemented by each iosched. This reduces
code duplication, eases enforcing semantics over dispatch
queue, and simplifies specific ioscheds.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
|
|
This patch removes try_module_get race in elevator_find.
try_module_get should always be called with the spinlock protecting
what the module init/cleanup routines register/unregister to held. In
the case of elevators, we should be holding elv_list to avoid it going
away between spin_unlock_irq and try_module_get.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
|
|
disk stat when "now" is different from disk->stamp. Otherwise, we
are again needlessly adding zero to the stats.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
|
|
struct gendisk has these two fields: stamp, stamp_idle. Update to
stamp_idle is always in sync with stamp and they are always the same.
Therefore, it does not add any value in having two fields tracking
same timestamp. Suggest to remove it.
Also, we should only update gendisk stats with non-zero value.
Advantage is that we don't have to needlessly calculate memory address,
and then add zero to the content.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
|
|
|
|
|
