aboutsummaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2009-12-14Merge branch 'x86-fixes-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: x86, mce: Clean up thermal init by introducing intel_thermal_supported() x86, mce: Thermal monitoring depends on APIC being enabled x86: Gart: fix breakage due to IOMMU initialization cleanup x86: Move swiotlb initialization before dma32_free_bootmem x86: Fix build warning in arch/x86/mm/mmio-mod.c x86: Remove usedac in feature-removal-schedule.txt x86: Fix duplicated UV BAU interrupt vector nvram: Fix write beyond end condition; prove to gcc copy is safe mm: Adjust do_pages_stat() so gcc can see copy_from_user() is safe x86: Limit the number of processor bootup messages x86: Remove enabling x2apic message for every CPU doc: Add documentation for bootloader_{type,version} x86, msr: Add support for non-contiguous cpumasks x86: Use find_e820() instead of hard coded trampoline address x86, AMD: Fix stale cpuid4_info shared_map data in shared_cpu_map cpumasks Trivial percpu-naming-introduced conflicts in arch/x86/kernel/cpu/intel_cacheinfo.c
2009-12-14Merge git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6: pcmcia: CodingStyle fixes pcmcia: remove unused IRQ_FIRST_SHARED
2009-12-14Merge branch 'next-spi' of git://git.secretlab.ca/git/linux-2.6Linus Torvalds
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6: (23 commits) spi: fix probe/remove section markings Add OMAP spi100k driver spi-imx: don't access struct device directly but use dev_get_platdata spi-imx: Add mx25 support spi-imx: use positive logic to distinguish cpu variants spi-imx: correct check for platform_get_irq failing ARM: NUC900: Add spi driver support for nuc900 spi: SuperH MSIOF SPI Master driver V2 spi: fix spidev compilation failure when VERBOSE is defined spi/au1550_spi: fix setupxfer not to override cfg with zeros spi/mpc8xxx: don't use __exit_p to wrap plat_mpc8xxx_spi_remove spi/i.MX: fix broken error handling for gpio_request spi/i.mx: drain MXC SPI transfer buffer when probing device MAINTAINERS: add SPI co-maintainer. spi/xilinx_spi: fix incorrect casting spi/mpc52xx-spi: minor cleanups xilinx_spi: add a platform driver using the xilinx_spi common module. xilinx_spi: add support for the DS570 IP. xilinx_spi: Switch to iomem functions and support little endian. xilinx_spi: Split into of driver and generic part. ...
2009-12-14Merge branch 'for-linus' of git://neil.brown.name/mdLinus Torvalds
* 'for-linus' of git://neil.brown.name/md: (27 commits) md: add 'recovery_start' per-device sysfs attribute md: rcu_read_lock() walk of mddev->disks in md_do_sync() md: integrate spares into array at earliest opportunity. md: move compat_ioctl handling into md.c md: revise Kconfig help for MD_MULTIPATH md: add MODULE_DESCRIPTION for all md related modules. raid: improve MD/raid10 handling of correctable read errors. md/raid10: print more useful messages on device failure. md/bitmap: update dirty flag when bitmap bits are explicitly set. md: Support write-intent bitmaps with externally managed metadata. md/bitmap: move setting of daemon_lastrun out of bitmap_read_sb md: support updating bitmap parameters via sysfs. md: factor out parsing of fixed-point numbers md: support bitmap offset appropriate for external-metadata arrays. md: remove needless setting of thread->timeout in raid10_quiesce md: change daemon_sleep to be in 'jiffies' rather than 'seconds'. md: move offset, daemon_sleep and chunksize out of bitmap structure md: collect bitmap-specific fields into one structure. md/raid1: add takeover support for raid5->raid1 md: add honouring of suspend_{lo,hi} to raid1. ...
2009-12-14Merge branch 'for-next' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6 * 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (58 commits) mfd: Add twl6030 regulator subdevices regulator: Add support for twl6030 regulators rtc: Add twl6030 RTC support mfd: Add support for twl6030 irq framework mfd: Rename twl4030_ routines in twl-regulator.c mfd: Rename twl4030_ routines in rtc-twl.c mfd: Rename all twl4030_i2c* mfd: Rename twl4030* driver files to enable re-use mfd: Clarify twl4030 return value for read and write mfd: Add all twl4030 regulators to the twl4030 mfd driver mfd: Don't set mc13783 ADREFMODE for touch conversions mfd: Remove ezx-pcap defines for custom led gpio encoding mfd: Near complete mc13783 rewrite mfd: Remove build time warning for WM835x register default tables mfd: Force I2C to be built in when building WM831x mfd: Don't allow wm831x to be built as a module mfd: Fix incorrect error check for wm8350-core mfd: Fix twl4030 warning gpiolib: Implement gpio_to_irq() for wm831x mfd: Remove default selection of AB4500 ...
2009-12-14Merge branch 'devel' of master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: ARM: fix lh7a40x build ARM: fix sa1100 build ARM: fix clps711x, footbridge, integrator, ixp2000, ixp2300 and s3c build bug ARM: VFP: fix vfp thread init bug and document vfp notifier entry conditions ARM: pxa: fix now incorrect reference of skt->irq by using skt->socket.pci_irq [ARM] pxa/zeus: default configuration for Arcom Zeus SBC. [ARM] pxa/zeus: make Viper pcmcia support more generic to support Zeus [ARM] pxa/zeus: basic support for Arcom Zeus SBC [ARM] pxa/em-x270: fix usb hub power up/reset sequence PCMCIA: fix pxa2xx_lubbock modular build error ARM: RealView: Fix typo in the RealView/PBX Kconfig entry ARM: Do not allow the probing of the local timer ARM: Add an earlyprintk debug console
2009-12-14Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (34 commits) m68k: rename global variable vmalloc_end to m68k_vmalloc_end percpu: add missing per_cpu_ptr_to_phys() definition for UP percpu: Fix kdump failure if booted with percpu_alloc=page percpu: make misc percpu symbols unique percpu: make percpu symbols in ia64 unique percpu: make percpu symbols in powerpc unique percpu: make percpu symbols in x86 unique percpu: make percpu symbols in xen unique percpu: make percpu symbols in cpufreq unique percpu: make percpu symbols in oprofile unique percpu: make percpu symbols in tracer unique percpu: make percpu symbols under kernel/ and mm/ unique percpu: remove some sparse warnings percpu: make alloc_percpu() handle array types vmalloc: fix use of non-existent percpu variable in put_cpu_var() this_cpu: Use this_cpu_xx in trace_functions_graph.c this_cpu: Use this_cpu_xx for ftrace this_cpu: Use this_cpu_xx in nmi handling this_cpu: Use this_cpu operations in RCU this_cpu: Use this_cpu ops for VM statistics ... Fix up trivial (famous last words) global per-cpu naming conflicts in arch/x86/kvm/svm.c mm/slab.c
2009-12-14md: add 'recovery_start' per-device sysfs attributeDan Williams
Enable external metadata arrays to manage rebuild checkpointing via a md/dev-XXX/recovery_start attribute which reflects rdev->recovery_offset Also update resync_start_store to allow 'none' to be written, for consistency. Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14md: rcu_read_lock() walk of mddev->disks in md_do_sync()Dan Williams
Other walks of this list are either under rcu_read_lock() or the list mutation lock (mddev_lock()). This protects against the improbable case of a disk being removed from the array at the start of md_do_sync(). Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2009-12-14md: integrate spares into array at earliest opportunity.NeilBrown
As v1.x metadata can record that a member of the array is not completely recovered, it make sense to record that a spare has become a regular member of the array at the earliest opportunity. So remove the tests on "recovery_offset > 0" in super_1_sync as they really aren't needed, and schedule a metadata update immediately after adding spares to a degraded array. This means that if a crash happens immediately after a recovery starts, the new device will be included in the array and recovery will continue from wherever it was up to. Previously this didn't happen unless recovery was at least 1/16 of the way through. Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14md: move compat_ioctl handling into md.cArnd Bergmann
The RAID ioctls are only implemented in md.c, so the handling for them should also be moved there from fs/compat_ioctl.c. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Neil Brown <neilb@suse.de> Cc: Andre Noll <maan@systemlinux.org> Cc: linux-raid@vger.kernel.org Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14md: revise Kconfig help for MD_MULTIPATHNeilBrown
Make it clear in the config message that MD_MULTIPATH is not under active development. Cc: Oren Held <orenhe@il.ibm.com> Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14md: add MODULE_DESCRIPTION for all md related modules.NeilBrown
Suggested by Oren Held <orenhe@il.ibm.com> Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14raid: improve MD/raid10 handling of correctable read errors.Robert Becker
We've noticed severe lasting performance degradation of our raid arrays when we have drives that yield large amounts of media errors. The raid10 module will queue each failed read for retry, and also will attempt call fix_read_error() to perform the read recovery. Read recovery is performed while the array is frozen, so repeated recovery attempts can degrade the performance of the array for extended periods of time. With this patch I propose adding a per md device max number of corrected read attempts. Each rdev will maintain a count of read correction attempts in the rdev->read_errors field (not used currently for raid10). When we enter fix_read_error() we'll check to see when the last read error occurred, and divide the read error count by 2 for every hour since the last read error. If at that point our read error count exceeds the read error threshold, we'll fail the raid device. In addition in this patch I add sysfs nodes (get/set) for the per md max_read_errors attribute, the rdev->read_errors attribute, and added some printk's to indicate when fix_read_error fails to repair an rdev. For testing I used debugfs->fail_make_request to inject IO errors to the rdev while doing IO to the raid array. Signed-off-by: Robert Becker <Rob.Becker@riverbed.com> Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14md/raid10: print more useful messages on device failure.Robert Becker
When we get a read error on a device in a RAID10, and attempting to repair the error fails, print more useful messages about why it failed. Signed-off-by: Robert Becker <Rob.Becker@riverbed.com> Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14md/bitmap: update dirty flag when bitmap bits are explicitly set.NeilBrown
There is a sysfs file which allows bits in the write-intent bitmap to be explicit set - indicating that the block is thought to be 'dirty'. When this happens we should really set recovery_cp backwards to include the block to reflect this dirtiness. In particular, a 'resync' process will refuse to start if recovery_cp is beyond the end of the array, so this is needed to allow a resync to be triggered. Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14md: Support write-intent bitmaps with externally managed metadata.NeilBrown
In this case, the metadata needs to not be in the same sector as the bitmap. md will not read/write any bitmap metadata. Config must be done via sysfs and when a recovery makes the array non-degraded again, writing 'true' to 'bitmap/can_clear' will allow bits in the bitmap to be cleared again. Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14md/bitmap: move setting of daemon_lastrun out of bitmap_read_sbNeilBrown
Setting daemon_lastrun really has nothing to do with reading the bitmap superblock, it just happens to be needed at the same time. bitmap_read_sb is about to become options, so move that code out to after the call to bitmap_read_sb. Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14md: support updating bitmap parameters via sysfs.NeilBrown
A new attribute directory 'bitmap' in 'md' is created which contains files for configuring the bitmap. 'location' identifies where the bitmap is, either 'none', or 'file' or 'sector offset from metadata'. Writing 'location' can create or remove a bitmap. Adding a 'file' bitmap this way is not yet supported. 'chunksize' and 'time_base' must be set before 'location' can be set. 'chunksize' can be set before creating a bitmap, but is currently always over-ridden by the bitmap superblock. 'time_base' and 'backlog' can be updated at any time. Signed-off-by: NeilBrown <neilb@suse.de> Reviewed-by: Andre Noll <maan@systemlinux.org>
2009-12-14md: factor out parsing of fixed-point numbersNeilBrown
safe_delay_store can parse fixed point numbers (for fractions of a second). We will want to do that for another sysfs file soon, so factor out the code. Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14md: support bitmap offset appropriate for external-metadata arrays.NeilBrown
For md arrays were metadata is managed externally, the kernel does not know about a superblock so the superblock offset is 0. If we want to have a write-intent-bitmap near the end of the devices of such an array, we should support sector_t sized offset. We need offset be possibly negative for when the bitmap is before the metadata, so use loff_t instead. Also add sanity check that bitmap does not overlap with data. Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14md: remove needless setting of thread->timeout in raid10_quiesceNeilBrown
As bitmap_create and bitmap_destroy already set thread->timeout as appropriate, there is no need to do it in raid10_quiesce. There is a possible need to wake the thread after the timeout has been set low, but it is better to do that where the timeout is actually set low, in bitmap_create. Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14md: change daemon_sleep to be in 'jiffies' rather than 'seconds'.NeilBrown
This removes a lot of multiplications by HZ. Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14md: move offset, daemon_sleep and chunksize out of bitmap structureNeilBrown
... and into bitmap_info. These are all configuration parameters that need to be set before the bitmap is created. Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14md: collect bitmap-specific fields into one structure.NeilBrown
In preparation for making bitmap fields configurable via sysfs, start tidying up by making a single structure to contain the configuration fields. Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14md/raid1: add takeover support for raid5->raid1NeilBrown
A 2-device raid5 array can now be converted to raid1. Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14md: add honouring of suspend_{lo,hi} to raid1.NeilBrown
This will allow us to stop writeout to portions of the array while they are resynced by someone else - e.g. another node in a cluster. Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14md/raid5: don't complete make_request on barrier until writes are scheduledNeilBrown
The post-barrier-flush is sent by md as soon as make_request on the barrier write completes. For raid5, the data might not be in the per-device queues yet. So for barrier requests, wait for any pre-reading to be done so that the request will be in the per-device queues. We use the 'preread_active' count to check that nothing is still in the preread phase, and delay the decrement of this count until after write requests have been submitted to the underlying devices. Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14md: support barrier requests on all personalities.NeilBrown
Previously barriers were only supported on RAID1. This is because other levels requires synchronisation across all devices and so needed a different approach. Here is that approach. When a barrier arrives, we send a zero-length barrier to every active device. When that completes - and if the original request was not empty - we submit the barrier request itself (with the barrier flag cleared) and then submit a fresh load of zero length barriers. The barrier request itself is asynchronous, but any subsequent request will block until the barrier completes. The reason for clearing the barrier flag is that a barrier request is allowed to fail. If we pass a non-empty barrier through a striping raid level it is conceivable that part of it could succeed and part could fail. That would be way too hard to deal with. So if the first run of zero length barriers succeed, we assume all is sufficiently well that we send the request and ignore errors in the second run of barriers. RAID5 needs extra care as write requests may not have been submitted to the underlying devices yet. So we flush the stripe cache before proceeding with the barrier. Note that the second set of zero-length barriers are submitted immediately after the original request is submitted. Thus when a personality finds mddev->barrier to be set during make_request, it should not return from make_request until the corresponding per-device request(s) have been queued. That will be done in later patches. Signed-off-by: NeilBrown <neilb@suse.de> Reviewed-by: Andre Noll <maan@systemlinux.org>
2009-12-14md: don't reset curr_resync_completed after an interrupted resyncNeilBrown
If a resync/recovery/check/repair is interrupted for some reason, it can be useful to know exactly where it got up to. So in that case, do not clear curr_resync_completed. Initialise it when starting a resync/recovery/... instead. Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14md: adjust resync_min usefully when resync aborts.NeilBrown
When a 'check' or 'repair' finished we should clear resync_min so that a future check/repair will cover the whole array (by default). However if it is interrupted, we should update resync_min to where we got up to, so that when the check/repair continues it just does the remainder of the array. Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14md: remove sparse warning:symbol XXX was not declared.NeilBrown
Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14md/raid5: remove some sparse warnings.NeilBrown
qd_idx is previously declared and given exactly the same value! Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14md/bitmap: protect against bitmap removal while being updated.NeilBrown
A write intent bitmap can be removed from an array while the array is active. When this happens, all IO is suspended and flushed before the bitmap is removed. However it is possible that bitmap_daemon_work is still running to clear old bits from the bitmap. If it is, it can dereference the bitmap after it has been freed. So introduce a new mutex to protect bitmap_daemon_work and get it before destroying a bitmap. This is suitable for any current -stable kernel. Signed-off-by: NeilBrown <neilb@suse.de> Cc: stable@kernel.org
2009-12-14mfd: Add twl6030 regulator subdevicesRajendra Nayak
This patch adds initial support for creating twl6030 PMIC specific voltage regulators in the twl mfd driver. Board specific regulator configurations will have to be passed from respective board files. Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Balaji T K <balajitk@ti.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Reviewed-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2009-12-14regulator: Add support for twl6030 regulatorsRajendra Nayak
This patch updates the regulator driver to add support for TWL6030 PMIC specific LDO regulators. SMPS resources are not yet supported for TWL6030 and also .set_mode and .get_status for LDO's are yet to be implemented for TWL6030. Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Balaji T K <balajitk@ti.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Reviewed-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2009-12-14rtc: Add twl6030 RTC supportBalaji T K
This patch adds support for RTC in phoenix TWL6030. Register offset addresses have changed in TWL6030 rtc-twl.c will hence forth support all twl RTC (4030, 5030, 6030 ..) Signed-off-by: Balaji T K <balajitk@ti.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Reviewed-by: Tony Lindgren <tony@atomide.com> Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2009-12-14mfd: Add support for twl6030 irq frameworkBalaji T K
This patch adds support for phoenix interrupt framework. New iInterrupt status register A, B, C are introduced in Phoenix and are cleared on write. Due to the differences in interrupt handling with respect to TWL4030, twl6030-irq.c is created for TWL6030 PMIC Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Balaji T K <balajitk@ti.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Reviewed-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2009-12-13mfd: Rename twl4030_ routines in twl-regulator.cRajendra Nayak
This patch renames all twl4030_ functions to twl so that regulator driver can be reused by Triton - TWL4030 and Phoenix - TWL6030. Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Balaji T K <balajitk@ti.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Acked-by: Kevin Hilman <khilman@deeprootsystems.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2009-12-13mfd: Rename twl4030_ routines in rtc-twl.cBalaji T K
This patch renames all twl4030_ functions to twl_ so that RTC driver can be shared between Triton and Phoenix. Signed-off-by: Balaji T K <balajitk@ti.com> Signed-off-by: Nayak Rajendra <rnayak@ti.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Acked-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2009-12-13mfd: Rename all twl4030_i2c*Balaji T K
This patch renames function names like twl4030_i2c_write_u8, twl4030_i2c_read_u8 to twl_i2c_write_u8, twl_i2c_read_u8 and also common variable in twl-core.c Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Balaji T K <balajitk@ti.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Acked-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2009-12-13Merge branch 'master' into develRussell King
2009-12-13mfd: Rename twl4030* driver files to enable re-useSantosh Shilimkar
The upcoming TWL6030 is companion chip for OMAP4 like the current TWL4030 for OMAP3. The common modules like RTC, Regulator creates opportunity to re-use the most of the code from twl4030. This patch renames few common drivers twl4030* files to twl* to enable the code re-use. Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Balaji T K <balajitk@ti.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Acked-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2009-12-13mfd: Clarify twl4030 return value for read and writeAmit Kucheria
We should be checking if all the messages were tranferred. If not, then we should propagate the i2c core error code or EIO. Currently we return success (0) even if none of messages were transferred successfully. Signed-off-by: Amit Kucheria <amit.kucheria@verdurent.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2009-12-13mfd: Add all twl4030 regulators to the twl4030 mfd driverJuha Keski-Saari
Add all twl4030 regulators to the twl4030 mfd driver and twl4030_platform_data Signed-off-by: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2009-12-13mfd: Don't set mc13783 ADREFMODE for touch conversionsUwe Kleine-König
Setting ADREFMODE is utter nonsense, but that's hard to read out of the spec. Strange enough it's possible to read x and y values even when it's set. When unset you can get values not only for the axes, but also for contact resistance which allows the touch driver to report pressure values. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2009-12-13mfd: Near complete mc13783 rewriteUwe Kleine-König
This fixes several things while still providing the old API: - simplify and fix locking - better error handling - don't ack all irqs making it impossible to detect a reset of the rtc - use a timeout variant to wait for completion of ADC conversion - provide platform-data to regulator subdevice (This allows making struct mc13783 opaque for other drivers after the regulator driver is updated to use its platform_data.) - expose all interrupts - use threaded irq After all users in mainline are converted to the new API, some things (e.g. mc13783-private.h) can go away. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2009-12-13mfd: Remove build time warning for WM835x register default tablesMark Brown
Systems using the WM835x need to choose which of the default register settings are required on the system. Currently there is a compile time warning as well as a runtime error intended to flag up to users that this is required but this also triggers for people building the driver in order to obtain build coverage. Remove the build warning, leaving only the runtime error, in order to reduce noise for people doing generic kernel work. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2009-12-13mfd: Force I2C to be built in when building WM831xMark Brown
This works around issues with allmodconfig where it won't propagate the dependency from the WM831x core back to the I2C and MFD cores. When doing allmodconfig this causes WM831x to be omitted and ensures that in normal builds the dependencies get shaken out. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2009-12-13mfd: Don't allow wm831x to be built as a moduleMark Brown
The genirq infrastructure functions aren't currently exported, preventing modular builds. Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>