| Age | Commit message (Collapse) | Author |
|---|
|
Prevent read from cards[-1] when no card was found.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An `options[cards_found]' that equals `sizeof(options_mapping)' is already beyond
the array.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If vlan has been enabled. ifdown followed by ifup will lost hardware
related state.
Also remove duplicated operation in gfar_vlan_rx_register().
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Acked-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bank offset was being incorrectly calculated on ICH9 parts with a bank
size of 8K (instead of the more common 4K bank) which would cause any NVM
writes to be done on the wrong address after switching from bank 1 to bank
0. Additionally, assume we are meant to use bank 0 if a valid bank is not
detected, and remove the unnecessary acquisition of the SW/FW/HW semaphore
when writing to the shadow ram version of the NVM image.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For ICHx parts, write the EXTCNF_CTRL.SWFLAG bit once when trying to
acquire the SW/FW/HW semaphore instead of multiple times to prevent the
hardware from having problems (especially for systems with manageability
enabled), and extend the timeout for the hardware to set the SWFLAG bit.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For 82599, packet split has to be disabled for FCoE direct data placement.
However, this is only required on received queues allocated for FCoE. This
patch adds a per ring flags to indicate if packet split is disabled on a
per queue basis, particularly for FCoE, as packet split must be disabled
for large receive using direct data placement (DDP).
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of passing the register index of the corresponding rx_ring and find
the way back to get to corresponding rx_ring in ixgbe_configure_srrctl(),
simplify the function ixgbe_configure_srrctl() by passing the rx_ring into
it. Then the register index for that rx_ring is already available from
rx_ring->reg_idx.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As it is, parts of the ioctl runs under the RTNL and parts of
it do not. The unlocked section is still protected by the BKL,
but there can be subtle races. For example, Eric Biederman and
Paul Moore observed that if two threads tried to create two tun
devices on the same file descriptor, then unexpected results
may occur.
As there isn't anything in the ioctl that is expected to sleep
indefinitely, we can prevent this from occurring by extending
the RTNL lock coverage.
This also allows to get rid of the BKL.
Finally, I changed tun_get_iff to take a tun device in order to
avoid calling tun_put which would dead-lock as it also tries to
take the RTNL lock.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit f0b3fbeae11a526c3d308b691684589ee37c359b ("FEC Buffer rework")
breaks transmission of packets where the skb data buffer is not memory
aligned according to FEC_ALIGNMENT. It incorrectly passes to
dma_sync_single() the buffer address directly from the skb, instead of
the address calculated for use (which may be the skb address or one of
the bounce buffers).
It seems there is no use converting the cpu address of the buffer to
a physical either, since dma_map_single() expects the cpu address and
will return the dma address to use in the descriptor. So remove the use
of __pa() on the buffer address as well.
This patch is against 2.6.30-rc5. This breakage is a regression over
2.6.30, which does not have this problem.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
strlcpy() will always null terminate the string.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Chris Snook <csnook@redhat.com>
Cc: Jie Yang <jie.yang@atheros.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
io[i] is read before the bounds check on i, order should be reversed.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
* 'for-linus' of git://git.infradead.org/ubi-2.6:
UBI: compatible fallback in absense of sequence numbers
UBI: fix double free on error path
|
|
these errors are pretty pointless
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Some applications/hardware combinations are triggering the message "failed to
acquire vblank counter" to be issued up to 20 times a second, which makes it
both useless and dangerous, as this may hide other important messages.
This changes makes it only appear when people are debugging.
Signed-off-by: Paul Rolland <rol@as2917.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Lost-twice-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The code which takes probed modes and adds them to a connector eliminates
duplicate modes by comparing them using drm_mode_equal. That function
doesn't consider the type bits, which means that any modes which differ only
in the type field will be lost.
One of the bits in the mode->type field is the DRM_MODE_TYPE_PREFERRED bit.
If the mode with that bit is lost, then higher level code will not know
which mode to select, causing a random mode to be used instead.
This patch simply merges the two mode type bits together; that seems
reasonable to me, but perhaps only a subset of the bits should be used? None
of these can be user defined as they all come from looking at just the
hardware.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: fix oops on disconnect in cdc-acm
USB: storage: include Prolific Technology USB drive in unusual_devs list
USB: ftdi_sio: add product_id for Marvell OpenRD Base, Client
USB: ftdi_sio: add vendor and product id for Bayer glucose meter serial converter cable
USB: EHCI: fix counting of transaction error retries
USB: EHCI: fix two new bugs related to Clear-TT-Buffer
USB: usbfs: fix -ENOENT error code to be -ENODEV
USB: musb: fix the nop registration for OMAP3EVM
USB: devio: Properly do access_ok() checks
USB: pl2303: New vendor and product id
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
Staging: rspiusb: Fix buffer overflow
staging: add dependencies on PCI for drivers that require it
Staging: rtl8192su: fix build error
Staging: rt2870: Revert d44ca7 Removal of kernel_thread() API
Staging: rt2870: Add USB ID for Linksys, Planex Communications, Belkin
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel: (22 commits)
drm/i915: Fix read outside array bounds in restoring the SWF10 range.
drm/i915: Use our own workqueue to avoid wedging the system along with the GPU.
drm/i915: Add support for dual-channel LVDS on 8xx.
drm/i915: Return disconnected for SDVO DVI when there's no digital EDID.
drm/i915: Choose real sdvo output according to result from detection
drm/i915: Set preferred mode for integrated TV according to TV format
drm/i915: fix 845G FIFO size & burst length
drm/i915: fix VGA detect on IGDNG
drm/i915: Add eDP support on IGDNG mobile chip
drm/i915: enable DisplayPort support on IGDNG
drm/i915: Fix channel ending action for DP aux transaction
drm/i915: fix issue in display pipe setup on IGDNG
drm/i915: disable VGA plane reliably
drm/I915: Fix offset to DVO timings in LVDS data
drm/i915: hdmi detection according by reading edid
drm/i915: correct self-refresh calculation in "everything off" case
drm/i915: handle FIFO oversubsription correctly
drm/i915: FIFO watermark calculation fixes
drm/i915: ignore lvds on AOpen Mini PC MP-915
drm/i915: Allow frame buffers up to 4096x4096 on 915/945 class hardware
...
|
|
usb_buffer_map_sg() may return -1. This will result in a read from
pdx->PixelUrb[frameInfo][-1]
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch adds PCI dependencies to staging drivers that require it.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This fixes a build error when selecting the rtl8192su driver as a
module. This has been reported by me, and the opensuse kernel developer
team, and I finally tracked it down.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Staging: rt2870: Revert d44ca7 Removal of kernel_thread() API
The sanity check this patch introduced triggers on shutdown, apparently due to
threads having already exited by the time BUG_ON() is reached.
Signed-off-by: Mike Galbraith <efault@gmx.de>
Cc: Peter Teoh <htmldeveloper@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Linksys WUSB100, Belkin F5D8053 N, Planex Communications unknown model.
Signed-off-by: Jakob Gruber <jakob.gruber@kabelnet.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch fixes an oops caused when during an unplug a device's table
of endpoints is zeroed before the driver is notified. A pointer to
the endpoint must be cached.
this fixes a regression caused by commit
5186ffee2320942c3dc9745f7930e0eb15329ca6
Therefore it should go into 2.6.31
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Add a quirk entry for the Leading Driver UD-11 usb flash drive.
As Alan Stern told me, the device doesn't deal correctly with the
locking media feature of the device, and this patch incorporates it.
Compiled, tested, working.
Signed-off-by: Rogerio Brito <rbrito@ime.usp.br>
Cc: Phil Dibowitz <phil@ipom.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Robert Hancock <hancockrwd@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
reference:
http://www.open-rd.org
Signed-off-by: Dhaval Vasa <dhaval.vasa@einfochips.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
converter cable
Attached patch adds USB vendor and product IDs for Bayer's USB to serial
converter cable used by Bayer blood glucose meters. It seems to be a
FT232RL based device and works without any problem with ftdi_sio driver
when this patch is applied. See: http://winglucofacts.com/cables/
Signed-off-by: Marko Hänninen <bugitus@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1274) simplifies the counting of transaction-error
retries. Now we will count up from 0 to QH_XACTERR_MAX instead of
down from QH_XACTERR_MAX to 0.
The patch also fixes a small bug: qh->xacterr was not getting
initialized for interrupt endpoints.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Matthijs Kooijman <matthijs@stdin.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1273) fixes two(!) bugs introduced by the new
Clear-TT-Buffer implementation in ehci-hcd.
It is now possible for an idle QH to have some URBs on its
queue -- this will happen if a Clear-TT-Buffer is pending for
the QH's endpoint. Consequently we should not issue a warning
when someone tries to unlink an URB from an idle QH; instead
we should process the request immediately.
The refcounts for QHs could get messed up, because
submit_async() would increment the refcount when calling
qh_link_async() and qh_link_async() would then refuse to link
the QH into the schedule if a Clear-TT-Buffer was pending.
Instead we should increment the refcount only when the QH
actually is added to the schedule. The current code tries to
be clever by leaving the refcount alone if an unlink is
immediately followed by a relink; the patch changes this to an
unconditional decrement and increment (although they occur in
the opposite order).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Tested-by: Manuel Lauss <manuel.lauss@gmail.com>
Tested-by: Matthijs Kooijman <matthijs@stdin.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1272) changes the error code returned when an open call
for a USB device node fails to locate the corresponding device. The
appropriate error code is -ENODEV, not -ENOENT.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Kay Sievers <kay.sievers@vrfy.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
OMAP3EVM uses ISP1504 phy which doesn't require any programming and
thus has to use NOP otg transceiver.
Cleanups being done:
- Remove unwanted code in usb-musb.c file
- Register NOP in OMAP3EVM board file using
usb_nop_xceiv_register().
- Select NOP_USB_XCEIV for OMAP3EVM boards.
- Don't enable TWL4030_USB in omap3_evm_defconfig
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Eino-Ville Talvala <talvala@stanford.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
access_ok() checks must be done on every part of the userspace structure
that is accessed. If access_ok() on one part of the struct succeeded, it
does not imply it will succeed on other parts of the struct. (Does
depend on the architecture implementation of access_ok()).
This changes the __get_user() users to first check access_ok() on the
data structure.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: stable <stable@kernel.org>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
I am submitting a patch for the pl2303 driver. This patch adds support
for the "Sony QN-3USB" cable (vendor=0x054c, product=0x0437). This USB
cable is a so-called data cable used to connect a Sony mobile phone to a
computer. Supported models are Sony CMD-J5, J6, J7, J16, J26, J70 and
Z7.
I have used this patch with my Sony CMD-J70 for several days and I
haven't encountered any kernel/hardware issue.
From: Khanh-Dang Nguyen Thu Lam <kdntl@yahoo.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
* master.kernel.org:/home/rmk/linux-2.6-arm: (30 commits)
ARM: 5639/1: arm: clkdev.c should include <linux/clk.h>
ARM: 5638/1: arch/arm/kernel/signal.c: use correct address space for CRUNCH
ARM: 5637/1: [KS8695] Don't reference CLOCK_TICK_RATE in drivers
ARM: S3C64XX: serial: Fix section mismatch warning
ARM: S3C24XX: serial: Fix section mismatch warnings
ARM: S3C: PWM fix for low duty cycle
ARM: 5597/1: [PCI] reset all internal hardware prior PCI initialization
ARM: 5627/1: Fix restoring of lr at the end of mcount
ARM: 5624/1: Document cache aliasing region
S3C64XX: Fix ARMCLK configuration
S3C64XX: Fix get_rate() for ARMCLK
S3C24XX: GPIO: Fix pin range check in s3c_gpiolib_getchip
mx3 defconfig update
mx27 defconfig update
ARM: 5623/1: Treo680: ir shutdown typo fix
ARM: includecheck fix: plat-stmp3xxx/pinmux.c
ARM: includecheck fix: plat-s3c64xx/pm.c
ARM: includecheck fix: mach-omap2/mcbsp.c
ARM: includecheck fix: mach-omap1/mcbsp.c
ARM: includecheck fix: board-sffsdr.c
...
|
|
* git://git.infradead.org/~dwmw2/iommu-2.6.31:
intel-iommu: Fix enabling snooping feature by mistake
intel-iommu: Mask physical address to correct page size in intel_map_single()
intel-iommu: Correct sglist size calculation.
|
|
* git://git.infradead.org/mtd-2.6:
jffs2: Fix return value from jffs2_do_readpage_nolock()
mtd: mtdblock: introduce mtdblks_lock
mtd: remove 'SBC8240 Wind River' Device Driver Code
mtd: OneNAND: OMAP2/3: free GPMC CS on module removal
mtd: OneNAND: fix incorrect bufferram offset
mtd: blkdevs: do not forget to get MTD devices
mtd: fix the conversion from dev to mtd_info
mtd: let include/linux/mtd/partitions.h stand on its own
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: matrix_keypad - make matrix keymap size dynamic
Input: wistron_btns - support Prestigio Wifi RF kill button
Input: i8042 - add Asus G1S to noloop exception list
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: setup MC/VRAM the same way for suspend/resume
drm/radeon/kms: Fix caching mode selection for GTT object
|
|
sdhci_alloc_host returns an ERR_PTR value in an error case instead of NULL.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@match exists@
expression x, E;
statement S1, S2;
@@
x = sdhci_alloc_host(...)
... when != x = E
(
* if (x == NULL || ...) S1 else S2
|
* if (x == NULL && ...) S1 else S2
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Philip Langdale <philipl@overt.org>
Cc: Pierre Ossman <pierre@ossman.eu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Recent framebuffer locking patches first made affected systems unbootable,
then the dead-lock has been fixed but as of 2.6.31-rc4 the framebuffer on
mx3 machines doesn't work. Fix this.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Catalin and kmemleak spotted a leak of a VC screen buffer in
vc_allocate() due to the following chain of events:
vc_allocate()
visual_init(init=1)
vc->vc_sw->con_init(init=1)
fbcon_init()
vc_resize()
vc->screen_buf = kmalloc()
vc->screen_buf = kmalloc()
The common way for the VC drivers is to set the screen dimension
parameters manually in the init case and only call vc_resize() for
!init - which allocates a screen buffer according to the new
dimensions.
fbcon instead would do vc_resize() unconditionally and afterwards set
the dimensions manually (again) for !init - i.e. completely upside
down. The vc_resize() allocated buffer would then get lost by
vc_allocate() allocating a fresh one.
Use vc_resize() only for actual resizing to close the leak.
Set the dimensions manually only in initialization mode to remove the
redundant setting in resize mode.
The kmemleak trace from Catalin:
unreferenced object 0xde158000 (size 12288):
comm "Xorg", pid 1439, jiffies 4294961016
hex dump (first 32 bytes):
20 00 20 00 20 00 20 00 20 00 20 00 20 00 20 00 . . . . . . . .
20 00 20 00 20 00 20 00 20 00 20 00 20 00 20 00 . . . . . . . .
backtrace:
[<c006f74b>] __save_stack_trace+0x17/0x1c
[<c006f81d>] create_object+0xcd/0x188
[<c01f5457>] kmemleak_alloc+0x1b/0x3c
[<c006e303>] __kmalloc+0xdb/0xe8
[<c012cc4b>] vc_do_resize+0x73/0x1e0
[<c012cdf1>] vc_resize+0x15/0x18
[<c011afc1>] fbcon_init+0x1f9/0x2b8
[<c0129e87>] visual_init+0x9f/0xdc
[<c012aff3>] vc_allocate+0x7f/0xfc
[<c012b087>] con_open+0x17/0x80
[<c0120e43>] tty_open+0x1f7/0x2e4
[<c0072fa1>] chrdev_open+0x101/0x118
[<c006ffad>] __dentry_open+0x105/0x1cc
[<c00700fd>] nameidata_to_filp+0x2d/0x38
[<c00788cd>] do_filp_open+0x2c1/0x54c
[<c006fdff>] do_sys_open+0x3b/0xb4
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Tested-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This fixes a bug caused by changing pointers (viafb_mode, viafb_mode1)
assigned by module_param. It reduces driver complexity by not needlessly
changing these vars as they are only read once and removing now
superfluous code.
On unpatched kernels loading viafb with viafb_mode or viafb_mode1 option
used and afterwards unloading it results in:
kernel BUG at mm/slub.c:2926!
invalid opcode: 0000 [#1] PREEMPT
last sysfs file: /sys/devices/virtual/block/loop0/removable
Modules linked in: snd_hda_codec_realtek snd_hda_intel snd_hda_codec
snd_hwdep snd_pcm rtl8187 snd_timer eeprom_93cx6 mmc_block snd soundcore
via_sdmmc fb snd_page_alloc i2c_algo_bit i2c_viapro ehci_hcd uhci_hcd
cfbcopyarea mmc_core cfbimgblt cfbfillrect video output [last unloaded:
viafb]
Pid: 3355, comm: rmmod Not tainted (2.6.31-rc1 #0)
EIP: 0060:[<c106a759>] EFLAGS: 00010246 CPU: 0
EIP is at kfree+0x80/0xda
EAX: c17c2da0 EBX: dc7edbdc ECX: 0000010f EDX: 00000000
ESI: c102c700 EDI: dc7ed8fa EBP: d703ff2c ESP: d703ff20
DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 0068
Process rmmod (pid: 3355, ti=d703e000 task=db1412c0 task.ti=d703e000)
Stack:
dc7edbdc 00000014 00000016 d703ff40 c102c700 dc7f45d4 dc7f45d4 00000880
d703ff4c c103e571 00000000 d703ffac c103e751 66616976 da140062 db89ba80
00000328 d702edf8 db89ba80 d703ff9c c105d0f0 00000200 da14f898 00000014
Call Trace:
[<c102c700>] ? destroy_params+0x1e/0x2b
[<c103e571>] ? free_module+0xa2/0xd7
[<c103e751>] ? sys_delete_module+0x1ab/0x1da
[<c105d0f0>] ? do_munmap+0x20a/0x225
[<c10029b4>] ? sysenter_do_call+0x12/0x26
Code: 10 76 7a 8d 87 00 00 00 40 c1 e8 0c c1 e0 05 03 05 1c 87 41 c1 66 83 38 00 79 03 8b 40 0c 8b 10 84 d2 78 12 66 f7 c2 00 c0 75 04 <0f> 0b eb fe e8 6f 5a fe ff eb 47 8b 55 04 8b 58 0c 9c 5e fa 3b
EIP: [<c106a759>] kfree+0x80/0xda SS:ESP 0068:d703ff20
This is caused by the current code changing the pointers assigned by
module_param. During unload it tries to free the memory the pointers
point at which is now part of an internal structure.
The patch simply avoids changing the pointers. This is okay as they are
read only once during the initialization process.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Cc: Joseph Chan <JosephChan@via.com.tw>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix the rotate_ud() function not to crash in case of a font which has not
a width of multiple by 8: The inner loop of the font pixel copy should not
access a bit outside the font memory area. Subtract the shift offset from
the font width will prevent this.
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This was found using a semantic patch, more info can be found at:
http://www.emn.fr/x-info/coccinelle/
Signed-off-by: Stoyan Gaydarov <sgayda2@uiuc.edu>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Older Gcc compilers (3.4.5 tested) need additional hints in order to get
the packing of the rxpd structure (which contains a 16 bit union)
correct on the ARM processor.
struct txpd does not need these hints since it contains a 32 bit union
that packs naturally.
Signed-off-by: R.J.Dunlop <rdunlop@guralp.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We need to unregister our ieee80211_hw before resetting the chip, as
the former causes firmware commands to be issued which will time out
once the chip has been reset.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
