Age | Commit message (Collapse) | Author |
|
agp_efficeon_probe()
(This is a resend of a patch originally submitted on 24-Jul-2007 00:14)
Ok, this is something the coverity checker found (CID: 1813).
I'm not at all intimate with this code, so I'm not sure if this
attempt at a fix is correct (but at least it compiles).
Please look it over and NACK if bad or merge if good ;-)
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
|
|
* wrong argument passed to pci_unmap_single() on failure
exit paths
* leak in the same area
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* git://git.infradead.org/~dwmw2/mtd-2.6.23:
[MTD] Makefile fix for mtdsuper
|
|
* git://git.infradead.org/battery-2.6:
Don't compile the PMU power driver on 64-bit PowerPC
|
|
the early setup function serial8250_console_early_setup() can be called
from non __init code (eg. hotpluggable serial ports like serial_cs) so
remove the __init from the call chain to avoid crashes.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC]: Fix O_CLOEXEC values.
[SPARC32]: Fix modular build of floppy driver.
[SOUND] CS4231 SBus: Two fixes.
[CG6]: fix memory size detection
[SPARC64]: Add missing dma_sync_single_range_for_*().
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: fw-core: make two variables static
firewire: fw-ohci: dma_free_coherent needs IRQs enabled
firewire: fw-sbp2: set correct maximum payload (fixes CardBus adapters)
ieee1394: sbp2: more correct Kconfig dependencies
ieee1394: revert "sbp2: enforce 32bit DMA mapping"
|
|
This patch fixes memory size detection on the CG6 card.
The 1MB TGX card has dblbuf property set to 0.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We want drivers/mtd/{mtdcore, mtdsuper, mtdpart}.c to be built and linked
into the same mtd.ko module. Fix the Makefile to ensure this, and remove
duplicate MODULE_ declarations in mtdpart.c, as mtdcore.c already has them.
Signed-off-by: Satyam Sharma <satyam@infradead.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
The nand_base.c driver implicitly casts the uint32_t
eccpos array to 'int *', which is not only not guaranteed
to be the same sign as the source, but is not guaranteed
to be the same size.
Fix by changing nand_base.c to use uint32_t
referencing the eccpos fields.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
The patch below fixes nand driver for AT91 boards which do not have NAND
R/B signal connected to gpio (rdy_pin is not connected).
Signed-off-by: Ivan Kuten <ivan.kuten@promwad.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
When we mark block bad we have to get chip because this involves
writing to the page's OOB. We hit this bug in UBI - we observed
random obscure crashes when it marks block bad from the background
thread and there is some parallel task which utilizes flash.
This patch also adds a TODO note about BBT table protection which
it seems does not exist.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
The patch ensures that the current code (kernel 2.6.22) uses the bits
like the code prior to the refactoring. The variable "bits" is employed
in a useful way now.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
This fixes a leak in the !mtd->erasesize error path (Coverity 1765).
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
As far as I know, all CardBus FireWire 400 adapters have a maximum
payload of 1024 bytes which is less than the speed-dependent limit of
2048 bytes. Fw-sbp2 has to take the host adapter's limit into account.
This apparently fixes Juju's incompatibility with my CardBus cards, a
NEC based card and a VIA based card.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Kristian Høgsberg <krh@redhat.com>
|
|
Make the option SBP2_PHYS_DMA available on all architectures where it
compiles. This includes x86-64 where I runtime-tested it successfully.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Revert commit 0555659d63c285ceb7ead3115532e1b71b0f27a7 from 2.6.22-rc1.
The dma_set_mask call somehow failed on a PowerMac G5, PPC64:
http://lkml.org/lkml/2007/8/1/344
Should there ever occur a DMA mapping beyond the physical DMA range, a
proper SBP-2 firmware will report transport errors. So let's leave it
at that.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Tested-by: Olaf Hering <olh@suse.de>
|
|
We can't call hid_free_buffers() when the underlying usbhid_device
has already been freed.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Add forgotten freeing of usbhid_device structure.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
If, in usb_hid_configure(), we fail to allocate storage for 'usbhid',
"if (!(usbhid = kzalloc(sizeof(struct usbhid_device), GFP_KERNEL)))",
then we'll jump to the 'fail:' label where we have this code:
usb_free_urb(usbhid->urbin);
usb_free_urb(usbhid->urbout);
usb_free_urb(usbhid->urbctrl);
Since we got here because we couldn't allocate storage for 'usbhid',
what we have here is a NULL pointer dereference - ouch...
This patch solves that little problem by adding a new
'fail_no_usbhid:' label after the problematic calls to
usb_free_urb() and jumps to that one instead, in the problem case.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Some of ASUS' notebooks (e.g G Series) include a tiny oled display, which is
attached to an internal USB bus. Unfortunatly the device reports a wrong
DeviceDescriptor and is therefore identified as a HID device...
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This patch adds the entire range of Logitech's ProductIDs that are reserved
for their Harmony remotes. The in-kernel HID driver can't do anything with
these, and now there is a GPL user-space application that can handle them:
http://www.sf.net/projects/harmonycontrol
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The IR sensor in some newer Apple computers has no other
driver in the kernel, yet. However, the macmini driver in lirc
requires a HID device for the IR sensor.
Cc: Soeren Sonnenburg <kernel@nn7.de>
Signed-off-by: Tino Keitel <tino.keitel@tikei.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6:
scc_pata: PIO fixes
piix/slc90e66: fix PIO1 handling in ->speedproc method (take 2)
jmicron: PIO fixes
it8213: PIO fixes (take 2)
cs5535: PIO fixes
cs5520: fix PIO auto-tuning in ->ide_dma_check method
drivers/scsi/ide-scsi.c: kmalloc + memset conversion to kzalloc
drivers/ide/arm/icside.c: kmalloc + memset conversion to kzalloc
ide: eliminate warnings in ide-tape.c
ide: fix runtogether printk's in cmd64x IDE driver
sis5513: Add FSC Amilo A1630 PCI subvendor/dev to laptops
alim15x3: Correct HP detect
ide: Fix an overrun found in the CS5535 IDE driver
|
|
* Use pio == 255 == "auto-tune" in scc_config_drive_for_dma() instead of
forcing PIO4 on PIO fallback. Fix comment while at it.
* Rename scc_tuneproc() to scc_tune_pio() and add scc_tuneproc() wrapper.
Move finding of the best PIO mode and setting of transfer mode on the device
to the new wrapper.
* Fix scc_tune_chipset() to tune PIO modes. Do a small cleanup while at it.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Don't call {piix,slc90e66}_dma_2_pio() for PIO modes in
{piix,slc90e66}_tune_chipset().
* Add PIO1 handling to {piix,slc90e66}_tune_chipset().
* Bump driver version.
v2:
* Remove PIO modes from {piix,slc90e66}_dma_2_pio(), they are no longer needed
there (Noticed by Sergei)
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Set transfer mode on the device in jmicron_tuneproc(),
also add pio == 255 == "auto-tune" handling.
* Use jmicron_tuneproc() in jmicron_config_drive_for_dma().
* Remove no longer needed config_jmicron_chipset_for_pio().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Rename it8213_tuneproc() to it8213_tune_pio() and add it8213_tuneproc()
wrapper. Move finding of the best PIO mode to the new wrapper.
* Add setting of transfer mode on the device to it8213_tuneproc().
* Don't call it8213_dma_2_pio() for PIO modes in it8213_tune_chipset().
* Use it8213_tuneproc() in it8213_config_drive_for_dma().
v2:
* Remove PIO modes from it8213_dma_2_pio(), they are no longer needed there
(Noticed by Sergei)
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Fix cs5535_tuneproc() to pass PIO transfer mode value instead of PIO mode
number to cs5535_set_speed() (fixes random PIO timings being programmed
and a possible OOPS). Do a little cleanup while at it.
* Fix cs5535_set_speed() to check if the mate device is present (fixes PIO0
taskfile timings being used if there is no other device on the cable).
* Use cs5535_tuneproc() in cs5535_dma_check(). The old code had the same
issue as cs5535_tuneproc() and add additionally caused 0x00-0x04 transfer
mode values (== default PIO, default PIO w/ IORDY + two invalid values)
being set on the device instead of values 0x08-0x0c (XFER_PIO_[0,4]).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
drivers/scsi/ide-scsi.c | 34642 -> 34536 (-106 bytes)
drivers/scsi/ide-scsi.o | 171728 -> 171524 (-204 bytes)
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Is this a bug? In original verison memset cleared sizeof(state) bytes
instead of sizeof(*state). If it was intentional then this patch is invalid.
If not intentional -> valid :) Please review.
Bart: Yes, it is a bug so this patch is a valid bugfix. :-)
drivers/ide/arm/icside.c | 18883 -> 18849 (-34 bytes)
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
drivers/ide/ide-tape.c: In function '__idetape_kmalloc_stage':
drivers/ide/ide-tape.c:2588: warning: large integer implicitly truncated to unsigned type
drivers/ide/ide-tape.c:2616: warning: large integer implicitly truncated to unsigned type
b_size in struct idetape_bh is an unsigned short. We sometimes assigne
PAGE_SIZE to it and PAGE_SIZE can be 64K or larger, so make it a u32.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Fix a couple of runtogether printks in cmd64x.c IDE driver by adding
proper newlines.
Signed-off-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Recognise the FSC Amilo A1630's incarnation of a SiS5513 chip as laptop to
get UDMA100 support.
Signed-off-by: David Lamparter <equinox@diac24.net>
Cc: Lionel Bouton <Lionel.Bouton@inet6.fr>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Direct port of Alan's fix for pata_ali.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
As found by the Coverity checker, and reported by Adrian Bunk, this
fixes a overrun error in the CS5535 IDE driver. Somebody got a little
excited with the if() statement - the CS5535 only supports UDMA 0-4.
Bart:
Not a bug per se since the upper layer will never feed this function
with speed > XFER_UDMA_4 (thanks to ->ultra_mask being set to 0x1f).
Worth fixing anyway.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Fix MWDMA timings setup in sis_old_set_dmamode() and sis_66_set_dmamode().
The old timings were overclocked (even worse behavior than sis5513 IDE driver
which depends on BIOS to program correct timings), the new timings are taken
from the datasheet (they match timings from ATA spec).
* Fix UDMA timings setup in sis_old_set_dmamode().
Misplaced pci_write_config_word() call resulted in UDMA timings never
being set.
* Fix comments for sis_133_early_set_dmamode() and sis_133_set_dmamode():
- only the former function handles early SiS 961 bridges
- both functions lack MWDMA timings setup
* Fix typos in sis_100_set_piomode() and sis_133_set_piomode() comments.
* Bump driver version.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
SAMSUNG HD401LJ / ZZ100-15 does spurious completion of NCQ commands.
Disable NCQ. Reported by Ulrich in bugzilla #8805.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Ulrich <stellplatz-nr.13a@datenparkplatz.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Add Tecra M3 to the broken suspend blacklist. Tecra M3 doesn't have
proper DMI_PRODUCT_NAME but has an OEM_STRING instead. Match it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Separate out broken suspend blacklist matching into
piix_broken_suspend().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Rename __pci_reenable_device() to pci_reenable_device().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Seems nobody else is checking/testing this case as it keeps getting
horked.
If we have no BAR4 mapping on an SFF controller this is *NOT* an error,
it just means it isn't doing BMDMA.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
I must have been half asleep when doing the original code
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog: (28 commits)
[WATCHDOG] Fix pcwd_init_module crash
[WATCHDOG] ICH9 support for iTCO_wdt
[WATCHDOG] 631xESB/632xESB support for iTCO_wdt - add all LPC bridges
[WATCHDOG] 631xESB/632xESB support for iTCO_wdt
[WATCHDOG] omap_wdt.c - default error for IOCTL is -ENOTTY
[WATCHDOG] Return value of nonseekable_open
[WATCHDOG] mv64x60_wdt: Rework the timeout register manipulation
[WATCHDOG] mv64x60_wdt: disable watchdog timer when driver is probed
[WATCHDOG] mv64x60_wdt: Support the WDIOF_MAGICCLOSE feature
[WATCHDOG] mv64x60_wdt: Add a module parameter to change nowayout setting
[WATCHDOG] mv64x60_wdt: Add WDIOC_SETOPTIONS ioctl support
[WATCHDOG] mv64x60_wdt: Support for WDIOC_SETTIMEOUT ioctl
[WATCHDOG] mv64x60_wdt: Fix WDIOC_GETTIMEOUT return value
[WATCHDOG] mv64x60_wdt: Check return value of nonseekable_open
[WATCHDOG] mv64x60_wdt: Add arch/powerpc platform support
[WATCHDOG] mv64x60_wdt: Get register address from platform data
[WATCHDOG] mv64x60_wdt: set up platform_device in platform code
[WATCHDOG] ensure mouse and keyboard ignored in w83627hf_wdt
[WATCHDOG] s3c2410_wdt: fixup after arch include moves
[WATCHDOG] git-watchdog-typo
...
|
|
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (50 commits)
[MIPS] Add smp_call_function_single()
[MIPS] thread_info.h: kmalloc + memset conversion to kzalloc
[MIPS] Kexec: Fix several 64-bit bugs.
[MIPS] Kexec: Fix several warnings.
[MIPS] DDB5477: Remove support
[MIPS] Fulong: Remove unneeded header file
[MIPS] Cobalt: Enable UART on RaQ1
[MIPS] Remove unused GROUP_TOSHIBA_NAMES
[MIPS] remove some duplicate includes
[MIPS] Oprofile: Fix rm9000 performance counter handler
[MIPS] Use -Werror on subdirectories which build cleanly.
[MIPS] Yosemite: Fix warning.
[MIPS] PMON: Fix cpustart declaration.
[MIPS] Yosemite: Only build ll_ht_smp_irq_handler() if HYPERTRANSPORT.
[MIPS] Yosemite: Fix build error due to undeclared titan_mailbox_irq().
[MIPS] Yosemite: Don't declare titan_mailbox_irq() as asmlinkage.
[MIPS] Yosemite: Fix warnings in i2c-yoesmite by deleting the unused code.
[MIPS] Delete unused arch/mips/gt64120/common/
[MIPS] Fix build warning in unaligned load/store emulator.
[MIPS] IP32: Don't ignore request_irq's return value.
...
|
|
* 'release' of git://lm-sensors.org/kernel/mhoffman/hwmon-2.6:
hwmon: fscher read control bugfix
hwmon: (adm1031) Fix broken links in documentation
hwmon: make abituguru3_read_increment_offset() static
hwmon: Fix regression caused by typo in lm90.c
hwmon: (applesmc) add temperature sensors set for Macbook
hwmon: fscher control update bugfix
hwmon: fix dme1737 temp fault attribute
hwmon: Add missing __devexit tags in various drivers
hwmon: clean up duplicate includes
hwmon: fix lm78 detection regression
hwmon: fix array overruns in lm93.c
hwmon: add support for THMC50 and ADM1022
|
|
CONFIG_ACPI_PROCFS_SLEEP is a NO-OP -- delete it (again).
Apparently 296699de6bdc717189a331ab6bbe90e05c94db06 creating CONFIG_SUSPEND
and CONFIG_PM_SLEEP was based on an out-dated version of drivers/acpi/Kconfig,
as it erroneously restored this recently deleted config option.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|