| Age | Commit message (Collapse) | Author |
|---|
|
This change adds support for the mmc4 4-bit wide-bus mode.
The mmc4 spec defines 8-bit and 4-bit transfer modes. As we do not support
any 8-bit hardware, this patch only adds support for the 4-bit mode, but
it can easily be built upon when the time comes.
The 4-bit mode is electrically compatible with SD's 4-bit mode but the
procedure for turning it on is different. This patch implements only
the essential parts of the procedure as defined by the spec. Two additional
steps are recommended but not compulsory. I am documenting them here so
that there's a record.
1) A bus-test mechanism is implemented using dedicated mmc commands which allow
for testing the functionality of the data bus at the electrical level. This is
pretty paranoid and they way the commands work is not compatible with the mmc
subsystem (they don't set valid CRC values).
2) MMC v4 cards can indicate they would like to draw more than the default
amount of current in wide-bus modes. We currently will never switch the card
into a higher draw mode. Supposedly, allowing the card to draw more current
will let it perform better, but the specs seem to indicate that the card will
function correctly without the mode change. Empirical testing supports this
interpretation.
Signed-off-by: Philip Langdale <philipl@overt.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
This adds support for the high-speed modes defined by mmc v4
(assuming the host controller is up to it). On a TI sdhci controller,
it improves read speed from 1.3MBps to 2.3MBps. The TI controller can
only go up to 24MHz, but everything helps. Another person has taken
this basic patch and used it on a Nokia 770 to get a bigger boost
because that controller can run at 48MHZ.
Signed-off-by: Philip Langdale <philipl@overt.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
PXA MMC driver supports not only PXA255 but also PXA250 and newer ones
Signed-off-by: Marcin Juszkiewicz <hrw@openembedded.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
This patch is part of Juha Yrjola's and Komal Shah's earlier patch to
make general code cleanups
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar <at> indt.org.br>
Signed-off-by: Juha Yrjola <juha.yrjola <at> solidboot.com>
Signed-off-by: Komal Shah <komal_shah802003 <at> yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
This patch is part of Tony Lindgren's earlier patch to add
MMC_CAP_{MULTIWRITE,BYTEBLOCK} flags in omap.c
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar <at> indt.org.br>
Signed-off-by: Tony Lindgren <tony <at> atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
This patch is part of Juha Yrjola's earlier patch to add platform device
error handling and a BUG_ON to verify if host == NULL
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar <at> indt.org.br>
Signed-off-by: Juha Yrjola <juha.yrjola <at> solidboot.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
This patch is part of Juha Yrjola's earlier patch to move register
definitions away from the header file and the header file is removed.
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar <at> indt.org.br>
Signed-off-by: Juha Yrjola <juha.yrjola <at> solidboot.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
This patch is part of Juha Yrjola's earlier patch to change
OMAP_MMC_{READ,WRITE} macros to use the host pointer
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar <at> indt.org.br>
Signed-off-by: Juha Yrjola <juha.yrjola <at> solidboot.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
This patch is part of Juha Yrjola's earlier patch to replace base
with virt_base and phys_base
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar <at> indt.org.br>
Signed-off-by: Juha Yrjola <juha.yrjola <at> solidboot.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Now that mmc_host_ops can be constified, update the various drivers
to constify those method tables and shrink the writable data segment.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Replace kernel_thread() with kthread_run()/kthread_stop().
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
This changes the type of variable "i" in rtl8169_init_one()
from "unsigned int" to "int". "i" is checked for < 0 later,
which can never happen for "unsigned". This results in broken
error handling.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[PATCH] libata: Fixup ata_sas_queuecmd to handle __ata_scsi_queuecmd failure
[PATCH] ahci: AHCI mode SATA patch for Intel ICH9
[PATCH] libata: don't schedule EH on wcache on/off if old EH
|
|
When we sleep and wait for a suspended operation to be resumed, go
back and check until it's ready -- don't just continue after the first
time we're woken. This can cause file system corruption.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Fixes ata_sas_queuecmd to properly handle a failure from
__ata_scsi_queuecmd.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This patch adds the Intel ICH9 AHCI controller DID's for SATA support.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Do not schedule EH for revalidation on wcache on/off if old EH. Old
EH cannot handle it and will result in WARN_ON()'s and oops.
This closes bug #7412.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[XFRM] STATE: Fix to respond error to get operation if no matching entry exists.
[NET]: Re-fix of doc-comment in sock.h
[6PACK]: Masking bug in 6pack driver.
[NET]: Fix kfifo_alloc() error check.
[UDP]: Make udp_encap_rcv use pskb_may_pull
[NETFILTER]: H.323 conntrack: fix crash with CONFIG_IP_NF_CT_ACCT
|
|
The tda10086 causes an oops (divide by zero) if a zero symbol rate is used;
this prevents this.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
The old code would accept any device on the same i2c address as the
saa711x chips as an saa711x. However, this fails with saa717x chips,
which use that same address and so are misdetected as a saa7111. Now
check whether the chip is really a saa711x model.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
The patch fix bug 5748.
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Sparse noticed a lock imbalance in read_from_buf(). Further inspection shows
that the lock should not be held when the function exits.
This adds a spin_unlock_irqrestore(), so that every exit path of the
read_from_buf() function is consistent. The unlock was missing on an error
path.
Signed-off-by: Ira W. Snyder <devel@irasnyder.com>
Signed-off-by: Hans J. Koch <koch@hjk-az.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Spotted by coverity/Adrian Bunk.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
subsystem-id 13c2:1003
New module parameter diseqc_method for cards with subsystem-id 13c2:1003.
- 0: unreliable method, can be used by all board revisions (default)
- 1: reliable method, works for newer board layouts only
The parameter has no effect for cards with other subsystem-ids.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Fixes to DISEQC on these cards inadvertently broke normal tone/voltage
signalling. This restores the necessary function.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Looks like a broken masking to me, binary not is used where bitwise
not was intended.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a bug. When checking for ati_remote->outbuf we free freeing
ati_remote->inbuf so we end up freeing ati_remote->inbuf twice.
Also the checks for 'ati_remote->inbuf != NULL' and 'ati_remote->outbuf !=
NULL' are redundant as usb_buffer_free() does this.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Acked-by: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The return value of platform_device_register_simple() should be checked by
IS_ERR().
This patch also fix misc_register() error case. Because misc_register()
returns error code.
Cc: Sebastien Bouchard <sebastien.bouchard@ca.kontron.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch removes a module_exit function that sgiioc4 should not have had.
It seems that the IDE layer doesn't support submodule unloading. sgiioc4 was
the only driver in drivers/ide/pci that had an exit function. After an
unload, the devices would stay around and the next attempt to reference would
crash...
Signed-off-by: Jeremy Higdon <jeremy@sgi.com>
Acked-by: "Bartlomiej Zolnierkiewicz" <bzolnier@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
dev->devt_attr is allocated in device_add() but it is never freed in
device_del() in the drivers/base/core.c file (reported by kmemleak).
Signed-off-by: Catalin Marinas <catalin.marinas@gmail.com>
Acked-by: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The correct order is: NULL check before dereference
This was a guaranteed NULL dereference with debugging enabled since
rs5c372_sysfs_show_osc() does actually pass NULL...
Spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
I got a lockdep warning when running "rtctest" so I though it'd be good
to see what was up.
- The warning was for rtc->irq_task_lock, gotten from rtc_update_irq()
by irq handlerss ... but in a handful of other cases, grabbed without
blocking IRQs.
- Some callers to rtc_update_irq() were not ensuring IRQs were blocked,
yet the routine expects that; make sure all callers block IRQs.
It would appear that RTC API tests haven't been part of anyone's kernel
regression test suite recently, at least not with lockdep running.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The RTC framework has an irq_set_freq() method that should be used to manage
the periodic IRQ frequency, but the current ioctl logic doesn't know how to do
that. This patch teaches it how.
This means that drivers implementing irq_set_freq() will automatically support
RTC_IRQP_{READ,SET} ioctls; that logic doesn't need duplication within the
driver.
[akpm@osdl.org: export rtc_irq_set_freq]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Add required locking to dfbc9e9d33adb1ac9910dd7f8ceb911947039a52
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Pavol Gono <Palo.Gono@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Fix recent i2c-ixp4xx compilation breakage. Sorry for overlooking it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
processor_perflib.c::acpi_processor_ppc_notifier() check if the value
returned by the processor's _PPC method is 0 and return failed if so.
This is wrong since 0 indicate that the bios think the processor can go
to the highest frequency. This patch for example fix the HP NX 6125 to
allow its highest frequency to be available.
Signed-off-by: Bruno Ducrot <ducrot@poupinou.org>
Cc: "Pallipadi, Venkatesh" <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Not all graphic page remappers support physical addresses over the 4GB
mark for remapping, so while some do (the AMD64 GART always did, and I
just fixed the i965 to do so properly), we're safest off just forcing
GFP_DMA32 allocations to make sure graphics pages get allocated in the
low 32-bit address space by default.
AGP sub-drivers that really care, and can do better, could just choose
to implement their own allocator (or we could add another "64-bit safe"
default allocator for their use), but quite frankly, you're not likely
to care in practice.
So for now, this trivial change means that we won't be allocating pages
that we can't map correctly by mistake on x86-64.
[ On traditional 32-bit x86, this could never happen, because GFP_KERNEL
would never allocate any highmem memory anyway ]
Acked-by: Andi Kleen <ak@suse.de>
Acked-by: Dave Jones <davej@redhat.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This introduces a i965-specific "mask_memory()" function that knows
about the extended physical addresses that the i965 supports. This
allows us to correctly map in physical memory in the >4GB range into the
GTT.
Also simplify/clean-up the i965 case for the aperture sizing by just
returning the fixed 512kB size from "fetch_size()". We don't really
care that not all of the aperture may be visible - the only thing that
cares about the aperture size is the Intel "stolen memory" calculation,
which depends on the fixed size.
Cc: Keith Packard <keithp@keithp.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[TG3]: Add missing unlock in tg3_open() error path.
[IPV6]: Fix address/interface handling in UDP and DCCP, according to the scoping architecture.
[IRDA]: Lockdep fix.
[BLUETOOTH]: Fix unaligned access in hci_send_to_sock.
[XFRM]: nlmsg length not computed correctly in the presence of subpolicies
[XFRM]: Sub-policies broke policy events
[IGMP]: Fix IGMPV3_EXP() normalization bit shift value.
[Bluetooth] Ignore L2CAP config requests on disconnect
[Bluetooth] Always include MTU in L2CAP config responses
[Bluetooth] Check if RFCOMM session is still attached to the TTY
[Bluetooth] Handling pending connect attempts after inquiry
[Bluetooth] Attach low-level connections to the Bluetooth bus
[IPV6] IP6TUNNEL: Add missing nf_reset() on input path.
[IPV6] IP6TUNNEL: Delete all tunnel device when unloading module.
[IPV6] ROUTE: Do not enable router reachability probing in router mode.
[IPV6] ROUTE: Prefer reachable nexthop only if the caller requests.
[IPV6] ROUTE: Try to use router which is not known unreachable.
|
|
Sparse noticed a locking imbalance in tg3_open(). This patch adds an
unlock to one of the error paths, so that tg3_open() always exits
without the lock held.
Signed-off-by: Ira W. Snyder <kernel@irasnyder.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ONDEMAND governor needs FREQ_TABLE
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
ipath uses skb functions and won't build without CONFIG_NET.
Spotted by Randy Dunlap.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
This is a quick hack to overcome the fact that SRCU currently does not
allow static initializers, and we need to sometimes initialize those
things before any other initializers (even "core" ones) can do so.
Currently we don't allow this at all for modules, and the only user that
needs is right now is cpufreq. As reported by Thomas Gleixner:
"Commit b4dfdbb3c707474a2254c5b4d7e62be31a4b7da9 ("[PATCH] cpufreq:
make the transition_notifier chain use SRCU breaks cpu frequency
notification users, which register the callback > on core_init
level."
Cc: Thomas Gleixner <tglx@timesys.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Andrew Morton <akpm@osdl.org>,
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB: Clear high octet in QP number
|
|
Fix a build error for the enter:now PCI card.
Signed-off-by: Toralf Foerster <toralf.foerster@gmx.de>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Fix printk format warnings:
drivers/char/ftape/zftape/zftape-buffers.c:87: warning: format '%d' expects type
'int', but argument 3 has type 'size_t'
drivers/char/ftape/zftape/zftape-buffers.c:104: warning: format '%d' expects type
'int', but argument 3 has type 'size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
i2c_bit_add_bus() returns -E;
-E != 0 => err = 1
probe fails with positive error code
Signed-off-by: Alexey Dobriyan <adobriyan@openvz.org>
Cc: Deepak Saxena <dsaxena@mvista.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Having unbound PCMCIA devices: doing a 'find /sys' after a 'rmmod pcmcia'
gives an oops because the pcmcia_device is not unregisterd from the driver
core.
fixes bugzilla #7481
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Pavol Gono <Palo.Gono@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jbglaw/vax-linux
* 'fixes4linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbglaw/vax-linux:
lkkbd: Remove my old snail-mail address
|
