| Age | Commit message (Collapse) | Author |
|---|
|
|
|
Report KEY_BRIGHTNESSUP and KEY_BRIGHTNESSDOWN input events when the
ThinkPad is in "passive brightness control" mode (because either we or
ACPI video touched _BCL), and ACPI video is not processing these
events by itself.
This happens only on Lenovo ThinkPads with ACPI video support, when
operating with the ACPI video driver in acpi_backlight=vendor mode.
Issuing these events is the right thing to do, and will work around
bugzilla #13368, if userspace is properly configured and actively
handles these events.
For other ThinkPads, and when ACPI video is handling brightness
changes, thinkpad-acpi will continue NOT sending KEY_BRIGHTNESS*
events by default.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Init hotkey_source_mask late, so that we can make use of
hotkey_reserved_mask to avoid polling any of the reserved
hotkeys by default.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
echo "reset" > /proc/acpi/ibm/hotkey should do something non-useless,
so instead of setting it to Fn+F2, Fn+F3, Fn+F5, set it to
hotkey_recommended_mask.
It is not like it will survive for much longer, anyway.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Some analysis of the ACPI DSDTs shows that the HKEY pre-enabled mask
is always 0x80c (FN+F3,FN+F4 and FN+F12), which are the hotkeys that
the second gen of HKEY firmware supported (the first gen didn't report
any hotkeys, the second reported these tree hotkeys but had no mask
support, and the third added mask support).
So, this is probably some sort of backwards compatibility with older
versions of the IBM ThinkVantage suite. We have no use for that, and
I know of exactly ZERO users of that attribute, anyway. Start the
process of getting rid of it.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Fix some locking, avoid exiting the kthread before kthread_stop() is
called on it, and clean up the hotkey poll routines a little bit.
Also, restore bits in the firmware mask after hotkey_source_mask is
changed. Without this, we leave events disabled...
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Use stricter checks to decide that we're running on a supported ThinkPad.
This should remove some possible false positives, although nobody ever
bothered to report any.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Use the quirk infrastructure to warn of outdated firmware and also of
firmware versions that are known to cause problems.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
X40 (firmware 1V) and T41 (firmware 1R) have been confirmed to work
well with the new defaults, so we can stop pestering people to confirm
that fact.
For now, whitelist just these two firmware types. It is best to have
at least one more firmware type confirmed for Radeon 9xxx and Intel
GMA-2 ThinkPads before removing the confirmation requests entirely.
Reported-by: Robert de Rooy <robert.de.rooy@gmail.com>
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: stable@kernel.org
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Conflicts:
drivers/acpi/power.c
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] sizeof cleanup
[WATCHDOG] wdt_pci: fix printk and variable type
[WATCHDOG] wdt_pci - use pci_request_region
[WATCHDOG] ar7_wdt: Fix error handling during probe.
[WATCHDOG] ar7_wdt: convert to become a platform driver
[WATCHDOG] fix book E watchdog to take WDIOC_SETTIMEOUT arg in seconds
[WATCHDOG] davinci: use clock framework for timer frequency
[WATCHDOG] Use DIV_ROUND_UP() macro in the coh901327 WDT
[WATCHDOG] Add support for WM831x watchdog
[WATCHDOG] Add watchdog driver for NUC900
[WATCHDOG] add SBC-FITPC2 watchdog driver
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (262 commits)
sh: mach-ecovec24: Add user debug switch support
sh: Kill off unused se_skipped in alignment trap notification code.
sh: Wire up HAVE_SYSCALL_TRACEPOINTS.
video: sh_mobile_lcdcfb: use both register sets for display panning
video: sh_mobile_lcdcfb: implement display panning
sh: Fix up sh7705 flush_dcache_page() build.
sh: kfr2r09: document the PLL/FLL <-> RF relationship.
sh: mach-ecovec24: need asm/clock.h.
sh: mach-ecovec24: deassert usb irq on boot.
sh: Add KEYSC support for EcoVec24
sh: add kycr2_delay for sh_keysc
sh: cpufreq: Include CPU id in info messages.
sh: multi-evt support for SH-X3 proto CPU.
sh: clkfwk: remove bogus set_bus_parent() from SH7709.
sh: Fix the indication point of the liquid crystal of AP-325RXA(AP3300)
sh: Add EcoVec24 romImage defconfig
sh: USB disable process is needed if romImage boot for EcoVec24
sh: EcoVec24: add HIZA setting for LED
sh: EcoVec24: write MAC address in boot
sh: Add romImage support for EcoVec24
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Clean up linker script using standard macros.
[IA64] Use standard macros for page-aligned data.
[IA64] Use .ref.text, not .text.init for start_ap.
[IA64] sgi-xp: fix printk format warnings
[IA64] ioc4_serial: fix printk format warnings
[IA64] mbcs: fix printk format warnings
[IA64] pci_br, fix infinite loop in find_free_ate()
[IA64] kdump: Short path to freeze CPUs
[IA64] kdump: Try INIT regardless of
[IA64] kdump: Mask INIT first in panic-kdump path
[IA64] kdump: Don't return APs to SAL from kdump
[IA64] kexec: Unregister MCA handler before kexec
[IA64] kexec: Make INIT safe while transition to
[IA64] kdump: Mask MCA/INIT on frozen cpus
Fix up conflict in arch/ia64/kernel/vmlinux.lds.S as per Tony's
suggestion.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (55 commits)
regulator: Voltage count for AB3100
mfd: Convert WM8350 to use request_threaded_irq()
mfd: Update MAINTAINERS patterns for WM831x
mfd: Fix twl4030-power warnings
regulator: AB3100 support
rtc: AB3100 RTC support
mfd: Fix ab3100-otp build failure
mfd: OMAP: Board-specifc twl4030 DPS scripts for RX51 board
mfd: Print warning for twl4030 out-of-order script loading
mfd: Add support for TWL4030/5030 dynamic power switching
mfd: AB3100 OTP readout
regulator: Add Freescale MC13783 driver
mfd: Add Freescale MC13783 driver
mfd: AB3100 disable irq nosync
mfd: AB3100 alter default setting
mfd: AB3100 propagate error
mfd: AB3100 accessor function cleanups
rtc: Add support for RTCs on Wolfson WM831x devices
regulator: get pcap data from the parent device
input: PCAP2 misc input driver
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (47 commits)
OMAP clock: use debugfs_remove_recursive() for rewinding
OMAP2/3/4 core: create omap_device layer
OMAP: omap_hwmod: call omap_hwmod init at boot; create interconnects
OMAP2/3/4: create omap_hwmod layer
OMAP2/3 board-*.c files: read bootloader configuration earlier
OMAP2/3/4 PRCM: add module IDLEST wait code
OMAP2/3 PM: create the OMAP PM interface and add a default OMAP PM no-op layer
OMAP3 clock: remove superfluous calls to omap2_init_clk_clkdm
OMAP clock: associate MPU clocks with the mpu_clkdm
OMAP3 clock: Fixed processing of bootarg 'mpurate'
OMAP: SDRC: Add several new register definitions
OMAP: powerdomain: Fix overflow when doing powerdomain deps lookups.
OMAP: PM: Added suspend target state control to debugfs for OMAP3
OMAP: PM debug: Add PRCM register dump support
OMAP: PM debug: make powerdomains use PM-debug counters
OMAP: PM: Add pm-debug counters
OMAP: PM: Add closures to clkdm_for_each and pwrdm_for_each.
OMAP: PM: Hook into PM counters
OMAP: PM counter infrastructure.
OMAP3: PM: fix lockdep warning caused by omap3_pm_init
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Fix NULL ptr regression in powernow-k8
[CPUFREQ] Create a blacklist for processors that should not load the acpi-cpufreq module.
[CPUFREQ] Powernow-k8: Enable more than 2 low P-states
[CPUFREQ] remove rwsem lock from CPUFREQ_GOV_STOP call (second call site)
[CPUFREQ] ondemand - Use global sysfs dir for tuning settings
[CPUFREQ] Introduce global, not per core: /sys/devices/system/cpu/cpufreq
[CPUFREQ] Bail out of cpufreq_add_dev if the link for a managed CPU got created
[CPUFREQ] Factor out policy setting from cpufreq_add_dev
[CPUFREQ] Factor out interface creation from cpufreq_add_dev
[CPUFREQ] Factor out symlink creation from cpufreq_add_dev
[CPUFREQ] cleanup up -ENOMEM handling in cpufreq_add_dev
[CPUFREQ] Reduce scope of cpu_sys_dev in cpufreq_add_dev
[CPUFREQ] update Doc for cpuinfo_cur_freq and scaling_cur_freq
|
|
Commit ac89a9174 ("pty: don't limit the writes to 'pty_space()' inside
'pty_write()'") removed the pty_space() checking, in order to let the
regular tty buffer code limit the buffering itself.
That was all good, but as a subtle side effect it meant that we'd be
doing a tty_wakeup() even in the case where the buffers were all filled
up, and didn't actually make any progress on the write.
Which sounds innocuous, but it interacts very badly with the ppp_async
code, which has an infinite loop in ppp_async_push() that tries to push
out data to the tty. When we call tty_wakeup(), that loop ends up
thinking that progress was made (see the subtle interactions between
XMIT_WAKEUP and 'tty_stuffed' for details). End result: one unhappy ppp
user.
Fixed by noticing when tty_insert_flip_string() didn't actually do
anything, and then not doing any more processing (including, very much
not calling tty_wakeup()).
Bisected-and-tested-by: Peter Volkov <pva@gentoo.org>
Cc: stable@kernel.org (2.6.31)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Use sizeof(*) instead of sizeof * (See Codingstyle documentation).
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Fix printk format warning:
drivers/watchdog/wdt_pci.c:652: warning: format '%04x' expects type 'unsigned int', but argument 2 has type 'resource_size_t'
and then use resource_size_t for the "io" variable as well
so that it won't be truncated.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Use pci_request_region instead of request_region for this pci_driver.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Fix error handling in the probe function.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Tested-by: Florian Fainelli <florian@openwrt.org>
|
|
This patch converts the ar7_wdt driver to become
a platform driver. The AR7 SoC specific identification
and base register calculation is performed by the board
code, therefore we no longer need to have access to
ar7_chip_id. We also remove the reboot notifier code to
use the platform shutdown method as Wim suggested.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
The WDIOC_SETTIMEOUT argument is supposed to be a "seconds" value.
However, the book E wdt currently treats it as a "period" which is
interpreted in a board-specific way.
This patch allows the user to pass in a "seconds" value and the driver
will set the smallest timeout that is at least as large as specified
by the user. It's been tested on e500 hardware and works as
expected.
The patch only modifies the CONFIG_FSL_BOOKE case, the CONFIG_4xx case
is left unmodified as I don't have any hardware to test it on.
Signed-off-by: Chris Friesen <cfriesen@nortel.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Remove use of CLOCK_TICK_RATE in favor of using clock framework
for getting timer frequency.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
I saw Julia Lawalls various commits fixing up the use of rounding
macros and since my already submitted patch was not caught in this
I took it upon myself to fix it up for this driver as well.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
The WM831x series of devices provide a watchdog with configurable
behaviour on timer expiry.
Currently this driver support refreshes via a register or GPIO line and
autonomous refreshes from a hardware source (eg, a clock).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Add watchdog device driver for the Nuvoton NUC900 series SoCs.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Add support for watchdog found on SBC-FITPC2 board.
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: Add pata_atp867x driver for Artop/Acard ATP867X controllers
pata_amd: do not filter out valid modes in nv_mode_filter
sata_promise: update reset code
sata_promise: disable hotplug on 1st gen chips
libata: fix spurious WARN_ON_ONCE() on port freeze
ahci: restore pci_intx() handling
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc: Update defconfigs.
sparc: Kill PROM console driver.
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (66 commits)
be2net: fix some cmds to use mccq instead of mbox
atl1e: fix 2.6.31-git4 -- ATL1E 0000:03:00.0: DMA-API: device driver frees DMA
pkt_sched: Fix qstats.qlen updating in dump_stats
ipv6: Log the affected address when DAD failure occurs
wl12xx: Fix print_mac() conversion.
af_iucv: fix race when queueing skbs on the backlog queue
af_iucv: do not call iucv_sock_kill() twice
af_iucv: handle non-accepted sockets after resuming from suspend
af_iucv: fix race in __iucv_sock_wait()
iucv: use correct output register in iucv_query_maxconn()
iucv: fix iucv_buffer_cpumask check when calling IUCV functions
iucv: suspend/resume error msg for left over pathes
wl12xx: switch to %pM to print the mac address
b44: the poll handler b44_poll must not enable IRQ unconditionally
ipv6: Ignore route option with ROUTER_PREF_INVALID
bonding: make ab_arp select active slaves as other modes
cfg80211: fix SME connect
rc80211_minstrel: fix contention window calculation
ssb/sdio: fix printk format warnings
p54usb: add Zcomax XG-705A usbid
...
|
|
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (51 commits)
MIPS: BCM63xx: Add integrated ethernet mac support.
MIPS: BCM63xx: Add support for the Broadcom BCM63xx family of SOCs.
MIPS: BCM63xx: Add Broadcom 63xx CPU definitions.
MIPS: Octeon: Move some platform device registration to its own file.
MIPS: Don't corrupt page tables on vmalloc fault.
MIPS: Shrink the size of tlb handler
MIPS: Alchemy: override loops_per_jiffy detection
MIPS: hw_random: Add hardware RNG for Octeon SOCs.
MIPS: Octeon: Add hardware RNG platform device.
MIPS: Remove useless zero initializations.
MIPS: Alchemy: get rid of allow_au1k_wait
MIPS: Octeon: Set kernel_uses_llsc to false on non-SMP builds.
MIPS: Allow kernel use of LL/SC to be separate from the presence of LL/SC.
MIPS: Get rid of CONFIG_CPU_HAS_LLSC
MIPS: Malta: Remove pointless use use of CONFIG_CPU_HAS_LLSC
MIPS: Rewrite clearing of ll_bit on context switch in C
MIPS: Rewrite sysmips(MIPS_ATOMIC_SET, ...) in C with inline assembler
MIPS: Consolidate all CONFIG_CPU_HAS_LLSC use in a single C file.
MIPS: Clean up linker script using new linker script macros.
MIPS: Use PAGE_SIZE in assembly instead of _PAGE_SIZE.
...
|
|
This is a new pata driver for ARTOP 867X 64bit 4-channel UDMA133 ATA ctrls.
Based on the Atp867 data sheet rev 1.2, Acard, and in part on early ide codes
from Eric Uhrhane <ericu@google.com>.
Signed-off-by: John(Jung-Ik) Lee <jilee@google.com>
Reviewed-by: Grant Grundler <grundler@google.com>
Reviewed-by: Gwendal Gringo <gwendal@google.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
On a Compaq Presario V3000 laptop (NVIDIA MCP51 chipset), pata_amd selects
PIO0 mode for the PATA DVD-RAM drive instead of MWDMA2 which it supports:
ata4.00: ATAPI: HL-DT-ST DVDRAM GSA-4084N, KQ09, max MWDMA2
ata4: nv_mode_filter: 0x39f&0x7001->0x1, BIOS=0x0 (0x0) ACPI=0x7001 (60:600:0x11)
ata4.00: configured for PIO0
For some reason, the BIOS-set UDMA configuration returns 0 and the ACPI _GTM
reports that UDMA2 and PIO0 are enabled. This causes nv_mode_filter to end up
allowing only PIO0 and UDMA0-2. Since the drive doesn't support UDMA we end up
using PIO0.
Since the controllers should always support PIO4, MWDMA2 and UDMA2 regardless
of what cable type is used, let's make sure we don't filter out these modes
regardless of what wacky settings the BIOS is using.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
sata_promise's reset code has deviated quite a bit from
the Promise reference driver's, and it has been observed
to fail to recover from errors in some cases.
This patch thus updates the reset code to more closely
match the reference driver:
- soft reset (pdc_reset_port):
* wait for ATA engine to not be in packet command mode
(2nd gen only)
* write reset bit in PDC_CTLSTAT before the first read
in the loop
* for 2nd gen SATA follow up with FPDMA reset and clearing
error status registers
- hard reset (pdc_sata_hardreset):
* wait for ATA engine to not be in packet command mode
(2nd gen only)
* reset ATA engine via the PCI control register
* Tejun's change to use non-waiting hardreset + follow-up SRST
I'm not changing the hotplug mask bits since they are taken care
of by sata_promise's ->freeze() and ->thaw() operations. And I'm
not writing the PMP port # because that's always zero (for now).
Tested here on various controllers. In particular, one disk
which used to timeout and fail to recover from certain hdparm
and smartmonctl commands now works nicely.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
1st generation Promise SATA chips are prone to generating spurious
hotplug events which can disrupt normal operation. This has been
observed on 20376 and 20378 chips. This patch thus disables hotplug
support on 1st gen chips while leaving it enabled for 2nd gen chips.
The pdc_sata_hotplug_offset() function becomes redundant so it is
removed.
Tested on 1st gen 20376 and 20378 mainboard chips and on a 2nd gen
SATA300 PCI card.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Kurt Roeckx <kurt@roeckx.be>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Commit 54c38444fad6a99b4b19512f8f0055d69115e69e makes libata abort qcs
after the port is frozen. This is necessary to guarantee that TF
registers are accessed after the DMA engine is shutdown after an
error. However, this triggers WARN_ON_ONCE() check in
ata_qc_complete() spuriously. Move WARN_ON_ONCE() downwards such that
failing commands while frozen doesn't trigger it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Commit a5bfc4714b3f01365aef89a92673f2ceb1ccf246 dropped explicit
pci_intx() manipulation from ahci because it seemed unnecessary and
ahci doesn't seem to be the right place to be tweaking it if it were.
This was largely okay but there are exceptions. There was one on an
embedded platform which was fixed via firmware and now bko#14124
reports it on a HP DL320.
http://bugzilla.kernel.org/show_bug.cgi?id=14124
I still think this isn't something libata drivers should be caring
about (the only ones which are calling pci_intx() explicitly are
libata ones and one other driver) but for now reverting the change
seems to be the right thing to do.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
If we reach the test just below the loop with a `timeout' value of 0,
this does not mean that the timeout caused the loop to end, but rather
the `smi_rd.s.pending', in the last iteration. If timeout caused the
loop to end, then `timeout' is -1, not 0.
Since this can occur only in the last iteration, it is not very likely
to be a problem. By changing the post- to prefix decrement we ensure
that a timeout of 0 does mean it timed out.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
All cmds issued to BE after the creation of mccq must now use the mcc-q
(and not mbox) to avoid a hw issue that results in mbox poll timeout.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
use the wrong API when free dma. So when map dma use a flag to
demostrate whether it is 'pci_map_single' or 'pci_map_page'. When free
the dma, check the flags to select the right APIs('pci_unmap_single'
or 'pci_unmap_page').
set the flags type to u16 instead of unsigned long on David's comments.
Signed-off-by: Jie Yang <jie.yang@atheros.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
amd64_edac: check NB MCE bank enable on the current node properly
amd64_edac: Rewrite unganged mode code of f10_early_channel_count
amd64_edac: cleanup amd64_check_ecc_enabled
x86, EDAC: Provide function to return NodeId of a CPU
amd64_edac: build driver only on AMD hardware
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu: (53 commits)
m68knommu: Make PAGE_SIZE available to assembly files.
m68knommu: fix ColdFire definition of CLOCK_TICK_RATE
m68knommu: set multi-function pins for ethernet when enabled
m68knommu: remove special interrupt handling code for ne2k support
m68knommu: relax IO_SPACE_LIMIT setting
m68knommu: remove ColdFire direct interrupt register access
m68knommu: create a speciailized ColdFire 5272 interrupt controller
m68knommu: add support for second interrupt controller of ColdFire 5249
m68knommu: clean up old ColdFire timer irq setup
m68knommu: map ColdFire interrupts to correct masking bits
m68knommu: clean up ColdFire 532x CPU timer setup
m68knommu: simplify ColdFire "timers" clock initialization
m68knommu: support code to mask external interrupts on old ColdFire CPU's
m68knommu: merge old ColdFire interrupt controller masking macros
m68knommu: remove duplicate ColdFire mcf_autovector() code
m68knommu: move ColdFire INTC definitions to new include file
m68knommu: mask off all interrupts in ColdFire intc-simr controller
m68knommu: remove timer device interrupt setup for ColdFire 532x
m68knommu: remove interrupt masking from ColdFire pit timer
m68knommu: remove unecessary interrupt level setting in ColdFire 520x setup
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (lm85) Don't bind to Winbond/Nuvoton WPCD377I
hwmon: (pcf8591) Documentation clean-ups
hwmon: Clearly mark ACPI drivers as such
hwmon: Use resource_size
hwmon: Include <linux/io.h> instead of <asm/io.h>
hwmon: (tmp421) Add documentation
hwmon: Add driver for Texas Instruments TMP421/422/423 sensor chips
hwmon-vid: Ignore 6th VID pin of AMD family 0Fh processors
hwmon: (asus_atk0110) Add maintainer information
hwmon: (abituguru3) Support multiple DMI strings per chip ID
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb
* 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb:
uwb: avoid radio controller reset loops
uwb: stop uwbd thread if rc->start() fails
uwb: handle radio controller events with out-of-range IDs correctly
|
|
This sets the number of voltages for the AB3100 regulators so that
they play well with the voltage listing functions and can be used
properly with the MMC regulator integration glue for example.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
