Age | Commit message (Collapse) | Author |
|
The pipestat fields affect reporting of all vblank-related interrupts, so we
have to reset them during the irq_handler, and while enabling vblank
interrupts. Otherwise, if a pipe status field had been set to non-zero
before enabling reporting, we would never see an interrupt again.
This patch adds i915_enable_pipestat and i915_disable_pipestat to abstract
out the steps needed to change the reported interrupts.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
ml_ff_playback() uses spin_(un)lock_bh. However this function is
called with interrupts disabled from erase_effect() in
drivers/input/ff-core.c:196.
This is not permitted, and will result in a WARN_ON in the bottom
half handling code. This patch changes this function to just use
spin_lock_irqsave() instead, solving the problem and simplifying
the locking logic.
This was reported as entry #106559 in kerneloops.org
Reported-by: kerneloops.org
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Instead of using a spinlock, it is better to call the proper pcm stream
locking schema.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
New firmware image brings enhanced tuning performance.
Firmware is available for download at the following location:
http://www.steventoth.net/linux/sms1xxx
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The video device was part of the gspca device. On device disconnection
while streaming, the device structure is freed at close time.
In this case, the remaining close job on the video device run out of
allocated memory.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The previous subdriver protection against rmmod was done via the
file operations table in the device descriptor. On device disconnection
while streaming, the device structure was freed at close time, and the
module_put still used the module name in the freed area.
Now, explicit module get/put are done on open and close.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
As a side effect, the sd routine stop0 is called on disconnect.
This permits the subdriver to free its resources.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
|
|
the use of is_blah() suggests a 1 or 0 return. This assumption is made in
pxa25x_udc code such as:
dev->vbus = is_vbus_present();
where dev->vbus is a bitfield. This fix allows pxa25x_udc_probe to correctly
detect vbus. Other changes were to make its use consistent in the rest of
the code.
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
It causes recursive locking warning and is unneeded after
introduction of STARTED flag.
* Resume vs. stop is effectively solved by DISCONNECT flag.
* No problem in suspend vs. start -- urb is submitted even after open
which is possible after connect which is called after start.
* Resume vs. start solved by STARTED flag.
* Suspend vs. stop -- no problem in killing urb and timer twice.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5330/1: mach-pxa: Fixup reset for systems using reboot=cold or other strings
[ARM] pxa: fix incorrect PCMCIA PSKTSEL pin configuration for spitz
[ARM] pxa: fix I2C controller device being registered twice on Akita
pxafb: only initialize the smart panel thread when dealing with a smartpanel
pxafb: introduce LCD_TYPE_MASK and use it.
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: ACE1001 patch for cp2101.c
USB: usbmon: fix read(2)
USB: gadget rndis: send notifications
USB: gadget rndis: stop windows self-immolation
USB: storage: update unusual_devs entries for Nokia 5300 and 5310
USB: storage: updates unusual_devs entry for the Nokia 6300
usb: musb: fix bug in musb_schedule
USB: fix SB700 usb subsystem hang bug
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
intel-iommu: fix compile warnings
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (23 commits)
net: fix tiny output corruption of /proc/net/snmp6
atl2: don't request irq on resume if netif running
ipv6: use seq_release_private for ip6mr.c /proc entries
pkt_sched: fix missing check for packet overrun in qdisc_dump_stab()
smc911x: Fix printf format typo in smc911x driver.
asix: Fix asix-based cards connecting to 10/100Mbs LAN.
mv643xx_eth: fix recycle check bound
mv643xx_eth: fix the order of mdiobus_{unregister, free}() calls
sh: sh_eth: Update to change of mii_bus
TPROXY: supply a struct flowi->flags argument in inet_sk_rebuild_header()
TPROXY: fill struct flowi->flags in udp_sendmsg()
net: ipg.c fix bracing on endian swapping
phylib: Fix auto-negotiation restart avoidance
net: jme.c rxdesc.flags is __le16, other missing endian swaps
phylib: fix phy name example in documentation
net: Do not fire linkwatch events until the device is registered.
phonet: fix compilation with gcc-3.4
ixgbe: fix compilation with gcc-3.4
pktgen: fix multiple queue warning
net: fix ip_mr_init() error path
...
|
|
Newer versions of hald tries to open it to call QUERYCAP.
Due to the lack of a proper locking, it is possible to open the device
before it finishes initialization.
This patch adds a lock to avoid this risk, and to protect the list of
em28xx devices.
While here, remove the uneeded BKL lock.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Don't reconnect device in the USB-bus. Reconnect command was not
executed every time by device firmware and that causes harm.
Reconnection is not needed so remove it.
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Now that we have a polling task for IR, there's a race condition, since
IR can be polling while other operations are being doing. Also, we are
now sharing the same urb_buf for both read and write control urb
operations. So, we need a mutex.
Thanks to Davin Heitmueller <devin.heitmueller@gmail.com> for warning me.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Before this patch, every register setup on em28xx were dynamically
allocating a temporary buffer for control URB's to be handled.
To avoid this ping-pong, use, instead a pre-allocated buffer.
Also, be sure that read control URB's also use the buffer, instead of
relying on a stack buffer.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
em28xx_init_dev() has some error conditions that are not properly
de-allocating dev var, nor freeing the device number for a future usage.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
0x0810/0x0002 needs the very same handling as 0x0001.
Reported-by: Steve Conklin <sconklin@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
If the device is suspended with the cable disconnected, then
resumed with the cable connected, dev->open is called before
resume. During resume, we request an IRQ, but the IRQ was
already assigned during dev->open, resulting in the warning
shown below.
Don't request an IRQ if the device is running.
Call Trace:
[<c011b89a>] warn_on_slowpath+0x40/0x59
[<c023df15>] raw_pci_read+0x4d/0x55
[<c023dff3>] pci_read+0x1c/0x21
[<c01bcd81>] __pci_find_next_cap_ttl+0x44/0x70
[<c01bce86>] __pci_find_next_cap+0x1a/0x1f
[<c01bcef9>] pci_find_capability+0x28/0x2c
[<c01c4144>] pci_msi_check_device+0x53/0x62
[<c01c49c2>] pci_enable_msi+0x3a/0x1cd
[<e019f17b>] atl2_write_phy_reg+0x40/0x5f [atl2]
[<c01061b1>] dma_generic_alloc_coherent+0x0/0xd7
[<e019f107>] atl2_request_irq+0x15/0x49 [atl2]
[<e01a1481>] atl2_open+0x20b/0x297 [atl2]
[<c024a35c>] dev_open+0x62/0x91
[<c0248b9a>] dev_change_flags+0x93/0x141
[<c024f308>] do_setlink+0x238/0x2d5
[<c02501b2>] rtnl_setlink+0xa9/0xbf
[<c0297f0c>] mutex_lock+0xb/0x19
[<c024ffa7>] rtnl_dump_ifinfo+0x0/0x69
[<c0250109>] rtnl_setlink+0x0/0xbf
[<c024fe42>] rtnetlink_rcv_msg+0x185/0x19f
[<c0240fd1>] sock_rmalloc+0x23/0x57
[<c024fcbd>] rtnetlink_rcv_msg+0x0/0x19f
[<c0259457>] netlink_rcv_skb+0x2d/0x71
[<c024fcb7>] rtnetlink_rcv+0x14/0x1a
[<c025929e>] netlink_unicast+0x184/0x1e4
[<c025992a>] netlink_sendmsg+0x233/0x240
[<c023f405>] sock_sendmsg+0xb7/0xd0
[<c0129131>] autoremove_wake_function+0x0/0x2b
[<c0129131>] autoremove_wake_function+0x0/0x2b
[<c0147796>] mempool_alloc+0x2d/0x9e
[<c020c923>] scsi_pool_alloc_command+0x35/0x4f
[<c0297f0c>] mutex_lock+0xb/0x19
[<c028e867>] unix_stream_recvmsg+0x357/0x3e2
[<c01b81c9>] copy_from_user+0x23/0x4f
[<c02452ea>] verify_iovec+0x3e/0x6c
[<c023f5ab>] sys_sendmsg+0x18d/0x1f0
[<c023ffa8>] sys_recvmsg+0x146/0x1c8
[<c0240016>] sys_recvmsg+0x1b4/0x1c8
[<c0118f48>] __wake_up+0xf/0x15
[<c02586cd>] netlink_table_ungrab+0x17/0x19
[<c01b83ba>] copy_to_user+0x25/0x3b
[<c023fe4a>] move_addr_to_user+0x50/0x68
[<c0240266>] sys_getsockname+0x6f/0x9a
[<c0240280>] sys_getsockname+0x89/0x9a
[<c015046a>] do_wp_page+0x3ae/0x41a
[<c0151525>] handle_mm_fault+0x4c5/0x540
[<c02405d0>] sys_socketcall+0x176/0x1b0
[<c010376d>] sysenter_do_call+0x12/0x21
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Jay Cliburn <jcliburn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
In commit a96d6ef34, the mouse interfaces on the unibody macbooks were
put into hid mouse ignore list. This was a little bit too premature
though, as the corresponding bcm5974 changes are scheduled for 2.6.29.
Remove these devices from the ignore list for now, in order to provide at
least basic functionality with the HID driver.
Will be reintroduced in 2.6.29
Reported-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Signed-off-by: Vernon Sauder <VernonInHand@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add AX_MEDIUM_ENCK also when speed = 10/100Mbps. This allows my belkin
f5d5055 to work with my 100Mbps switch and with an old 10Mbps ISA card.
Without this patch, the card is recognized and the interface is brought
up fine, but no packets actually flow through the interface.
Signed-off-by: Pantelis Koukousoulas <pktoss@gmail.com>
Acked-by: David Hollis <dhollis@davehollis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When mv643xx_eth allocates skbuffs, it adds
'dma_get_cache_alignment() - 1' to the length it needs, so that it can
align the skb's ->data pointer to a cache boundary. When checking
whether a transmitted skbuff can be reused as a receive buffer, these
bytes needs to be included into the minimum bound for the recycle check.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update to change of mii_bus interface and fix some warning.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch which adds IDs for AKTAKOM USB->RS232 cable
(http://www.aktakom.ru/product/kio/ace-1001.htm) is attached.
From: M Kondrin <mkondrin@hppi.troitsk.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
There's a bug in the usbmon binary reader: When using read() to fetch
the packets and a packet's data is partially read, the next read call
will once again return up to len_cap bytes of data. The b_read counter
is not regarded when determining the remaining chunk size.
So, when dumping USB data with "cat /dev/usbmon0 > usbmon.trace" while
reading from a USB storage device and analyzing the dump file
afterwards it will get out of sync after a couple of packets.
Signed-off-by: Ingo van Lil <inguin@gmx.de>
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
It turns out that atomic_inc_return() returns the *new* value
not the original one, so the logic in rndis_response_available()
kept the first RNDIS response notification from getting out.
This prevented interoperation with MS-Windows (but not Linux).
Fix this to make RNDIS behave again.
Signed-off-by: Richard Röjfors <richard.rojfors@endian.se>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Somewhere in the conversion of the RNDIS gadget code to the new
framework, the descriptor of its data interface seems to have
been copied from the CDC Ethernet driver. Unfortunately that
means it got a nonzero altsetting ... which is incorrect. Issue
uncovered by Richard Röjfors <richard.rojfors@endian.se>.
This patch fixes that problem, and resolves at least some cases
of Windows XP bluescreening itself.
Tested-by: Richard Röjfors <richard.rojfors@endian.se>.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1168) updates the unusual_devs entry for the Nokia 5300.
According to Jorge Lucangeli Obes <t4m5yn@gmail.com>, some existing
models have a revision number lower than the lower limit of the
current entry.
The patch also moves the entry for the Nokia 5310 to its correct place
in the file.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1169) modifies the unusual_devs entry for the Nokia
6300. According to Maciej Gierok <mgierok@gmail.com> and David
McBride <dwm@doc.ic.ac.uk>, the revision limits need to be wider.
This fixes Bugzilla #11768.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This bug was introduced recently. Fix it before bigger
problems appear.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch is required for AMD SB700 south bridge revision A12 and A13 to avoid
USB subsystem hang symptom. The USB subsystem hang symptom is observed when the
system has multiple USB devices connected to it. In some cases a USB hub may be
required to observe this symptom.
This patch works around the problem by correcting the internal register setting
that will help by changing the behavior of the internal logic to avoid the
USB subsystem hang issue. The change in the behavior of the logic does not
impact the normal operation of the USB subsystem.
Reported-by: Volker Armin Hemmann <volker.armin.hemmann@tu-clausthal.de>
Tested-by: Volker Armin Hemmann <volker.armin.hemmann@tu-clausthal.de>
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Libin Yang <libin.yang@amd.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: Fix disable IRQ 0 in pci_reset_function()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: more general identifier for Phoenix BIOS
AMD IOMMU: check for next_bit also in unmapped area
AMD IOMMU: fix fullflush comparison length
AMD IOMMU: enable device isolation per default
AMD IOMMU: add parameter to disable device isolation
x86, PEBS/DS: fix code flow in ds_request()
x86: add rdtsc barrier to TSC sync check
xen: fix scrub_page()
x86: fix es7000 compiling
x86, bts: fix unlock problem in ds.c
x86, voyager: fix smp generic helper voyager breakage
x86: move iomap.h to the new include location
|
|
Fix printk format warnings when CCISS_DEBUG is defined.
drivers/block/cciss.c:2856: warning: format '%d' expects type 'int', but argument 2 has type 'long unsigned int'
drivers/block/cciss.c:3205: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'long unsigned int'
drivers/block/cciss.c:3236: warning: format '%x' expects type 'unsigned int', but argument 2 has type '__u64'
drivers/block/cciss.c:3246: warning: format '%x' expects type 'unsigned int', but argument 2 has type '__u64'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
OMAP LDP boot crash. This is because w1 subsystem changed the search
interface, so update omap_hdq's search interface to follow the change.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
One more error handling code should have kfree as well
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.miao@marvell.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
After commit a1d35a7a (cirrusfb: use modedb and add mode_option
parameter), these variables are no longer used, so remove them to fix
compilation warning.
Signed-off-by: Vlada Periæ <vlada.peric@gmail.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In order to analyze the SMC of the newer MacPros, applesmc needs to
recognize the machine. This patch adds the missing generic dmi_match
entry for MacPro models.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Error handling code following a kzalloc should free the allocated data.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,l;
position p1,p2;
expression *ptr != NULL;
@@
(
if ((x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...)) == NULL) S
|
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
)
<... when != x
when != if (...) { <+...x...+> }
x->f = E
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Richard Purdie <rpurdie@linux.intel.com>
Cc: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix unsafe order in dma mapping operation: always flush data from the
cache *BEFORE* invalidating it, to allow full duplex transfers where the
same buffer may be used for both writes and reads.
Signed-off-by: Andrea Paterniani <a.paterniani@swapp-eng.it>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The LCD driver core calls LCD drivers when either the blanking state or
the display mode has changed, but does not make any check to see if the
called driver has a .set_mode method.
This means if a driver only has a .set_power method then the system will
OOPS on changing mode (and with the console semaphore held so you cannot
easily see the problem).
Fix the problem by ensuring that either callback is valid before use.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When unloading viafb module it does not remove it's /proc/viafb/ subtree
which causes multiple viafb directories to appear below proc when
mobprobing viafb and also lets kernel WARN() on duplicate proc entries:
[ 145.458387] WARNING: at /usr/src/linux-2.6.28-rc3-git6/fs/proc/generic.c:551 proc_register+0xe6/0x160()
[ 145.458945] proc_dir_entry '/proc/viafb' already registered
[ 145.459278] Modules linked in: viafb(+) i2c_algo_bit cfbcopyarea cfbimgblt cfbfillrect snd_hda_intel snd_pcm snd_timer snd soundcore snd_page_alloc sg via_agp agpgart [last unloaded: drm]
[ 145.460647] Pid: 1904, comm: modprobe Tainted: G W 2.6.28-rc3-git6 #4
[ 145.461064] Call Trace:
[ 145.461248] [<c01066f1>] ? dump_stack+0x1/0x80
[ 145.461533] [<c01228a3>] warn_slowpath+0x63/0x80
[ 145.461851] [<c0253ec9>] ? idr_get_empty_slot+0xe9/0x250
[ 145.462186] [<c0254120>] ? ida_get_new_above+0xf0/0x150
[ 145.462528] [<c019fb86>] proc_register+0xe6/0x160
[ 145.462827] [<c019fdc6>] proc_mkdir_mode+0x36/0x50
[ 145.463135] [<c019fdef>] proc_mkdir+0xf/0x20
[ 145.463457] [<f807173c>] viafb_init+0x73c/0xc86 [viafb]
[ 145.463823] [<f8071000>] ? viafb_init+0x0/0xc86 [viafb]
[ 145.464147] [<c010111d>] do_one_initcall+0x2d/0x160
[ 145.464460] [<c01a6543>] ? sysfs_add_file+0x13/0x20
[ 145.464786] [<c015f031>] ? vfree+0x21/0x30
[ 145.465049] [<c01433b5>] ? load_module+0x1215/0x1500
[ 145.465381] [<c014e455>] ? __alloc_pages_internal+0x95/0x400
[ 145.465755] [<c0143723>] sys_init_module+0x83/0x1a0
[ 145.466065] [<c016ceed>] ? sys_read+0x3d/0x70
[ 145.466354] [<c0103bc1>] sysenter_do_call+0x12/0x25
[ 145.466653] ---[ end trace c84b37826e16748c ]---
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Cc: <JosephChan@via.com.tw>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fixes a data corruption bug in pxa2xx_spi.c when operating in full duplex
mode with DMA and using buffers that overlap.
SPI transmit and receive buffers are allowed to be the same or to overlap.
However, this driver fails if such overlap is attempted in DMA mode
because it maps the rx and tx buffers in the wrong order. By mapping
DMA_FROM_DEVICE (read) before DMA_TO_DEVICE (write), it invalidates the
cache before flushing it, thus discarding data which should have been
transmitted.
The patch corrects the order of mapping. This bug exists in all versions
of pxa2xx_spi.c; similar bugs are in the drivers for two other SPI
controllers (au1500, imx).
A version of this patch has been tested on kernel 2.6.20 using
verification of loopback data with: random transfer length, random
bits-per-word, random positive offsets (both larger and smaller than
transfer length) between the start of the rx and tx buffers, and varying
clock rates.
Signed-off-by: Ned Forrester <nforrester@whoi.edu>
Cc: Vernon Sauder <vernoninhand@gmail.com>
Cc: J. Scott Merritt <merrij3@rpi.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: <stable@kernel.org> [2.6.27.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Restore support for compiling tmiofb with acceleration disabled.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Enable -D DEBUG in the GRU Makefile if CONFIG_SGI_GRU_DEBUG is selected.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|