Age | Commit message (Collapse) | Author |
|
The patch ensures that a GSO skb has enough headroom
to push an encapsulating cpl_tx_pkt_lso header.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
connection type parameters
Extend the RGMII-Internal Delay specification case to include
TX-only and RX-only variants.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Tested-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Previously, Internal Delay specification implied the delay be
applied to both TX and RX. This patch allows for separate TX/RX-only
internal delay specification.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Tested-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The code to change MTU doesn't correctly handle all the chip variations
and requirements for restarting. On Genesis chips changing MTU would just
cause receiver to hang.
Use a simpler approach of just taking link down/up if needed.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
For compatiablity with sk98lin, make sure and set same values
in serial mode register.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Version for 2.6.24
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Need to increase TX threshold when doing Jumbo frames on dual port board
to avoid underruns. (Code from sk98lin).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The driver would not work over fibre if other end when down then
came back up (would require reloading driver). The correct way
to manage the link the same way for both TP and fibre.
Resloves problem described in: http://lkml.org/lkml/2007/11/6/395
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Make sure and retry when shutting down the MAC. This code is copied
from sk98lin driver.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Receive FIFO overrun is not catastrophic condition, so don't flush when
it happens.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The calculation of usable FIFO RAM is wrong in the skge driver.
First, is doesn't take into account the reserved area on the original
SysKonnect Genesis boards. Second it has an off-by-one error because
hw->ports is either 1 or 2.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Currently ctc-device initialization is broken (kernel bug in
ctc_new_device).
The new network namespace code reveals a deficiency of the
ctc driver. It should make use of alloc_netdev() as described
in Documentation/networking/netdevices.txt.
Signed-off-by: Peter Tiedemann <ptiedem@de.ibm.com>
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Fix the case when the card initialization fails on a mtu change and then
close is called (due to ifdown), which frees non existent rx buffers.
- Returning appropriate error codes in init_nic function.
- In s2io_close function s2io_card_down is called only when device is up.
- In s2io_change_mtu function return value of s2io_card_up function
is checked and returned if it failed.
Signed-off-by: Surjit Reang <surjit.reang@neterion.com>
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 into upstream-fixes
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ehca: Fix static rate if path faster than link
IPoIB: Fix oops if xmit is called when priv->broadcast is NULL
|
|
The formula would yield -1 if the path is faster than the link, which
is wrong in a bad way (max throttling). Clamp to 0, which is the
correct value.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 4680/1: parentheses around NR_IRQS definition
[ARM] 4679/1: AT91: Change maintainer email address
[ARM] 4675/1: pxa: fix mfp address definition error for pxa320
[ARM] 4674/1: pxa: increase LCD PCLK drive strength to fast 2mA for PXA300/PXA310
[ARM] 4673/1: pxa: add missing IRQ_SSP4 definitions for PXA3xx
[ARM] 4672/1: pxa: fix DRCMR(n) to support PXA27x and later processors
[ARM] 4665/1: fix __und_usr wrt accessing the undefined insn in user space
[ARM] 4659/1: remove possibilities for spurious false negative with __kuser_cmpxchg
[ARM] 4661/1: fix do_undefinstr wrt the enabling of IRQs
[ARM] uengine: fix memset size error
[ARM] 4648/1: i.MX/MX1 ensure more complete AITC initialization
[ARM] 4611/2: AT91: Fix GPIO buttons pins on SAM9261-EK.
[ARM] 4650/1: AT91: New-style init of I2C, support for i2c-gpio
[ARM] 4604/2: AT91: Master clock divistor on SAM9
[ARM] 4662/1: Fix PXA serial driver compilation if SERIAL_PXA_CONSOLE is disabled
[ARM] PXA ssp: unlock when ssp tries to close an invalid port
[ARM] 4654/1: pxa: update default MFP register value
[ARM] 4653/1: pxa: fix a gpio typo in mfp-pxa320.h
[ARM] 4652/1: pxa: fix a typo of pxa27x usb host clk definition
[ARM] 4651/1: pxa: add PXA3xx specific IRQ definitions
|
|
Signed-off-by: Joonwoo Park <joonwpark81@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Joonwoo Park <joonwpark81@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch fixes iwl_mac_add_interface.
1. Currently only one interface is supported, instead of silently retuning
0 now it returns -EOPNOTSUPP (By Johannes Berg)
2. It enables changing mac address from user space (By Ian Schram)
Signed-off-by: Tomas Winkler <tomas@localhost.localdomain>
Cc: Zhu Yi <yi.zhu@intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Cc: linux-wireless <linux-wireless@vger.kernel.org
Cc: Ian Schram <ischram@telenet.be>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
lbs_mac_event_disconnected() was called once and then never again
upon a hardware MAC event.
The reason was that the driver didn't clean the correct bit in the interrupt
cause register of the chip.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
I'm not sure why it was doing this, and I'm not sure I _want_ to know
why. But calling it NETIF_F_DYNALLOC doesn't change the fact that the
kernel believes it to be NETIF_F_IPV6_CSUM, and that IPv6 communication
is hence buggered.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Fix some left-over URLs and ifdefs in b43 and b43legacy drivers.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Saleem Abdulrasool <compnerd@compnerd.org>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
sdio_uart: fix sign of paramter status in sdio_uart_receive_chars()
|
|
This also fixes a sparse warning about different signedness.
Only compile tested, because i do not have the hardware.
Signed-off-by: Andre Haupt <andre@bitwigglers.org>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
ACPI uses NR_CPUS in various loops and in some it accesses per cpu data of
processors that are not present(!) and that will never be present.
The pointers to per cpu data are typically not initialized for processors
that are not present. So we seem to be reading something here from offset
0 in memory.
Make ACPI use nr_cpu_ids instead. That stops at the end of the possible
processors.
Convert one loop to NR_CPUS to use the cpu_possible map instead. That way
ranges of processor that can never be brought online are skipped during the
loop.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
RTC code is using mutex to assure exclusive access to /dev/rtc. This is
however wrong usage, as it leaves the mutex locked when returning into
userspace, which is unacceptable.
Convert rtc->char_lock into bit operation.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch adds Graphics Output Protocol support to the kernel. UEFI2.0 spec
deprecates Universal Graphics Adapter (UGA) protocol and only Graphics Output
Protocol (GOP) is produced. Therefore, the boot loader needs to query the
UEFI firmware with appropriate Output Protocol and pass the video information
to the kernel. As a result of GOP protocol, an EFI framebuffer driver is
needed for displaying console messages. The patch adds a EFI framebuffer
driver. The EFI frame buffer driver in this patch is based on the Intel Mac
framebuffer driver.
The ELILO bootloader takes care of passing the video information as
appropriate for EFI firmware.
The framebuffer driver has been tested in i386 kernel and x86_64 kernel on EFI
platform.
Signed-off-by: Chandramouli Narayanan <mouli@linux.intel.com>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <ak@suse.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Revert 7eea436433b7b18045f272562e256976f593f7c0.
Lucy said:
This patch will work with the 19HS but WILL BREAK all other Keyspan
adapters. It will take me a few days to get to looking at a correct fix but
that keyspan_send_setup(port, 1) (and the '1' is the important part) must
happen once when the port is first opened. The cflag can just be set to
whatever the normal default is for your serial environment.
So revert this again pending the proper fix.
Cc: Borislav Petkov <bbpetkov@yahoo.de>
Cc: Greg KH <greg@kroah.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Lucy McCoy <lucy@keyspan.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
screen_info.imacpm_seg
Cc: Edgar Hucek <hostmaster@ed-soft.at>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
got this HiSax bootup crash on a "make randconfig" bzImage bootup:
Calling initcall 0xc0bb1320: HiSax_init+0x0/0x380()
HiSax: Linux Driver for passive ISDN cards
HiSax: Version 3.5 (kernel)
HiSax: Layer1 Revision 2.46.2.5
HiSax: Layer2 Revision 2.30.2.4
HiSax: TeiMgr Revision 2.20.2.3
HiSax: Layer3 Revision 2.22.2.3
HiSax: LinkLayer Revision 2.59.2.4
HiSax: Total 1 card defined
HiSax: Card 1 Protocol EDSS1 Id=HiSax (0)
HiSax: HFC-S driver Rev. 1.10.2.4
HFCS: defined at 0x500 IRQ 5 HZ 250
Teles 16.3c: IRQ 5 count 0
HFCS: resetting card
Teles 16.3c: IRQ 5 count 0
Teles 16.3c: IRQ(5) getting no interrupts during init 1
HFCS: resetting card
------------[ cut here ]------------
kernel BUG at include/linux/timer.h:145!
invalid opcode: 0000 [#1] PREEMPT DEBUG_PAGEALLOC
Modules linked in:
Pid: 1, comm: swapper Not tainted (2.6.24-rc3 #2045)
EIP: 0060:[<c063afbf>] EFLAGS: 00010286 CPU: 0
EIP is at hfcs_card_msg+0x15f/0x180
EAX: c0cf2e5c EBX: 000000f2 ECX: 00000000 EDX: ffff1193
ESI: f76e8000 EDI: f76e8000 EBP: f7c23ec4 ESP: f7c23eac
DS: 007b ES: 007b FS: 0000 GS: 0000 SS: 0068
Process swapper (pid: 1, ti=f7c22000 task=f7c0e000 task.ti=f7c22000)
Stack: 00000000 f7c23ec4 c011703b 00000002 f76e8000 00000000 f7c23ef8 c060c3e5
c0a7c9c0 c0a315dc 00000005 00000001 00000000 f7c23f34 00000000 c0b5c9c0
f7c23f34 00000000 c0f5a8e0 f7c23f80 c0bb154f 00000000 00000001 c0a9b5b9
Call Trace:
[<c010339a>] show_trace_log_lvl+0x1a/0x40
[<c0103469>] show_stack_log_lvl+0xa9/0xe0
[<c010355f>] show_registers+0xbf/0x200
[<c01037a4>] die+0x104/0x220
[<c0103943>] do_trap+0x83/0xc0
[<c0103ca8>] do_invalid_op+0x88/0xa0
[<c083621a>] error_code+0x6a/0x70
[<c060c3e5>] checkcard+0x4a5/0x620
[<c0bb154f>] HiSax_init+0x22f/0x380
[<c0b867b7>] kernel_init+0x97/0x2a0
[<c0102f87>] kernel_thread_helper+0x7/0x20
=======================
Code: e8 43 ae ff 8b 57 3c 85 d2 0f 84 ef fe ff ff b8 a0 99 ad c0 b9 02 00 00 00 e8 ce 11 ae ff 83 c4 0c b8 00 00 00 00 5b 5e 5f c9 c3 <0f> 0b eb fe 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90
EIP: [<c063afbf>] hfcs_card_msg+0x15f/0x180 SS:ESP 0068:f7c23eac
Kernel panic - not syncing: Attempted to kill init!
The box has no HiSax card installed.
the reason for the crash is add_timer() done on an already running
timer. This happens because for some reason CARD_INIT is called twice.
this patch works this problem around by using mod_timer() - this gets
a booting system - but it would be nice to figure out why CARD_INIT
is done twice.
the ISDN config section (generated via make randconfig) is this:
#
# ISDN feature submodules
#
# CONFIG_ISDN_DRV_LOOP is not set
CONFIG_ISDN_DIVERSION=y
#
# ISDN4Linux hardware drivers
#
#
# Passive cards
#
CONFIG_ISDN_DRV_HISAX=y
#
# D-channel protocol features
#
CONFIG_HISAX_EURO=y
CONFIG_DE_AOC=y
# CONFIG_HISAX_NO_SENDCOMPLETE is not set
# CONFIG_HISAX_NO_LLC is not set
# CONFIG_HISAX_NO_KEYPAD is not set
CONFIG_HISAX_1TR6=y
CONFIG_HISAX_NI1=y
CONFIG_HISAX_MAX_CARDS=8
#
# HiSax supported cards
#
CONFIG_HISAX_16_0=y
# CONFIG_HISAX_16_3 is not set
# CONFIG_HISAX_TELESPCI is not set
CONFIG_HISAX_S0BOX=y
# CONFIG_HISAX_AVM_A1 is not set
CONFIG_HISAX_FRITZPCI=y
CONFIG_HISAX_AVM_A1_PCMCIA=y
CONFIG_HISAX_ELSA=y
CONFIG_HISAX_IX1MICROR2=y
CONFIG_HISAX_DIEHLDIVA=y
# CONFIG_HISAX_ASUSCOM is not set
# CONFIG_HISAX_TELEINT is not set
CONFIG_HISAX_HFCS=y
# CONFIG_HISAX_SEDLBAUER is not set
CONFIG_HISAX_SPORTSTER=y
# CONFIG_HISAX_MIC is not set
# CONFIG_HISAX_NETJET is not set
# CONFIG_HISAX_NETJET_U is not set
# CONFIG_HISAX_NICCY is not set
# CONFIG_HISAX_ISURF is not set
# CONFIG_HISAX_HSTSAPHIR is not set
# CONFIG_HISAX_BKM_A4T is not set
# CONFIG_HISAX_SCT_QUADRO is not set
# CONFIG_HISAX_GAZEL is not set
# CONFIG_HISAX_HFC_PCI is not set
# CONFIG_HISAX_W6692 is not set
# CONFIG_HISAX_HFC_SX is not set
# CONFIG_HISAX_DEBUG is not set
#
# HiSax PCMCIA card service modules
#
#
# HiSax sub driver modules
#
CONFIG_HISAX_ST5481=y
CONFIG_HISAX_HFCUSB=y
# CONFIG_HISAX_HFC4S8S is not set
CONFIG_HISAX_FRITZ_PCIPNP=y
CONFIG_HISAX_HDLC=y
#
# Active cards
#
CONFIG_ISDN_DRV_ICN=m
CONFIG_ISDN_DRV_PCBIT=m
CONFIG_ISDN_DRV_SC=y
# CONFIG_ISDN_DRV_ACT2000 is not set
CONFIG_HYSDN=m
# CONFIG_ISDN_DRV_GIGASET is not set
# CONFIG_ISDN_CAPI is not set
CONFIG_PHONE=y
CONFIG_PHONE_IXJ=m
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Kai Germaschewski <kai@germaschewski.name>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
- fix lockup when switching from early console to real console
- make sysrq reliable
- fix panic, if sysrq is issued before console is opened
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch corrects recently changed (and now invalid) Kconfig descriptions
for the DMA engine framework:
- Non-Intel(R) hardware also has DMA engines;
- DMA is used for more than memcpy and RAID offloading.
In fact, on most platforms memcpy and RAID aren't factors, and DMA
exists so that peripherals can transfer data to/from memory while
the CPU does other work.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch adds an additional loop, that delays turning off the DMA
until the LCDC core has been turned off. This prevents the picture
to be shifted some random length when the kernel re-initializes
the LCDC.
Without this patch, the LCDC keeps running for some small time after the
PWRCON:LCD_PWR has been cleared ; the FIFO suffers an underrun and on
re-starting the LCDC the FIFO data stays shifted.
This behavior has been seen and fixed on AT91SAM9261-EK and two custom
AT91SAM9261 boards, all of them having different LCD panels.
Thanks a lot to Anti Sullin for submitting this patch (long
time ago).
Signed-off-by: Anti Sullin <anti.sullin@artecdesign.ee>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove errnoeous x character from dev_dbg() call that stops the driver
compiling under debug.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There should be a pci_dev_put when breaking out of a loop that iterates
over calls to pci_get_device and similar functions.
This was fixed using the following semantic patch.
// <smpl>
@@
identifier d;
type T;
expression e;
iterator for_each_pci_dev;
@@
T *d;
...
for_each_pci_dev(d)
{... when != pci_dev_put(d)
when != e = d
(
return d;
|
+ pci_dev_put(d);
? return ...;
)
...}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Greg KH <greg@kroah.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The code in fb_ddc_read() is said to be based on the implementation of the
radeon driver:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=fc5891c8a3ba284f13994d7bc1f1bfa8283982de
However, comparing the old radeon driver code with the new fb_ddc code
reveals some differences. Most notably, the I2C bus lines are held at the
end of the function, while the original code was releasing them (as the
comment above correctly says.)
There are a few other differences, which appear to be responsible for read
failures on my system. While tracing low-level I2C code in i2c-algo-bit, I
noticed that the initial attempt to read the EDID always failed. It takes
one retry for the read to succeed. As we are about to remove this
automatic retry property from i2c-algo-bit, reading the EDID would really
fail.
As a summary, the I2C lines quirk which is supposedly needed to read EDID
on some older monitors is currently breaking the (first) read on all other
monitors (and might not even work with older ones - did anyone try since
October 2006?)
After applying the patch below, which makes the code in fb_ddc_read()
really similar to what the radeon driver used to have, the first EDID read
succeeds again.
On top of that, as it appears that this code has been broken for one year
now and nobody seems to have complained, I'm curious if it makes sense to
keep this quirk in place. It makes the code more complex and slower just
for the sake of monitors which I guess nobody uses anymore. Can't we just
get rid of it?
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Roger Leigh <rleigh@whinlatter.ukfsn.org>
Tested-by: Michael Buesch <mb@bu3sch.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
m68k: zorro7xx needs <asm/amigahw.h> if !CONFIG_AMIGA_PCMCIA
Reported by Ingo Juergensmann <ij@2007.bluespice.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Allow passing a bus number through the platform data for the S3C2410 SPI
GPIO driver. This is needed to support multiple SPI busses.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If we specify an GPIO which cannot be used for the purpose, then assume
that the GPIO is not to be used and do not try and configure it. This can
be the case where the SPI bus is TX only.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
During the initialization of the TPM TIS driver, the necessary locality has
to be requested earlier in the init-process. Depending on the used TPM
chip, this leads to wrong information. For example: Lenovo X61s with Atmel
TPM:
tpm_tis 00:0a: 1.2 TPM (device-id 0xFFFF, rev-id 255)
But correct is:
tpm_tis 00:0c: 1.2 TPM (device-id 0x3203, rev-id 9)
This short patch fixes this issue.
Signed-off-by: Marcel Selhorst <tpm@selhorst.net>
Cc: Kylene Jo Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
On some systems the number of resources(IO,MEM) returnedy by PNP device is
greater than the PNP constant, for example motherboard devices. It brings
that some resources can't be reserved and resource confilicts. This will
cause PCI resources are assigned wrongly in some systems, and cause hang.
This is a regression since we deleted ACPI motherboard driver and use PNP
system driver.
[akpm@linux-foundation.org: fix text and coding-style a bit]
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Thomas Renninger <trenn@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
- Limit video memory size to avoid crossing a 256 MiB boundary in IOIF space.
- Pass the actual amount of video memory used to lv1_gpu_memory_allocate().
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
- vuart.ko -> ps3-vuart.ko
- sys-manager.ko -> ps3-sys-manager.ko
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Make the atmel_spi driver label GPIOs according to the device for which
they're acting as a chipselect. This way the debugfs dump of gpio state is
more informative.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (25 commits)
USB: s3c2410 gadget: ensure vbus pin in input mode during read
USB: s3c2410 gadget: allow sharing of vbus irq
USB: s3c2410 gadget: Header move fixups
USB: usb-storage: unusual_devs entry for JetFlash TS1GJF2A
USB: fix up EHCI startup synchronization
USB: make the microtek driver and HAL cooperate
USB: uevent environment key fix
USB: keep track of whether interface sysfs files exist
USB: sierra: new product id
USB HCD: avoid duplicate local_irq_disable()
USB: mailing lists have changed
USB: remove USB HUB entry from MAINTAINERS
USB: fix directory references in usb/README
USB: add support for an older firmware revision for the Nikon D200
USB: FIx locks and urb->status in adutux (updated)
USB: power-management documenation update
USB: Fix signr comment in usbdevice_fs.h
usbserial: fix inconsistent lock state
USB: fix usbled disconnect read race #2
USB: free memory when writing fails in usb/serial/mos7840.c
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/pci-2.6:
pci hotplug: kernel-doc fixes
pci-aer: fix kernel-doc mistakes
PCI: drivers/pci/pci-sysfs.c: Add missing pci_dev_put
PCI: pcie portdriver: initialize returned value
|