| Age | Commit message (Collapse) | Author |
|---|
|
When ds3234 is built-in, the final links fails with the following vague error
message:
`.exit.text' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.exit.text' of drivers/built-in.o
ds3234_remove() cannot be marked __exit, as it's accessed via __devexit_p().
In addition, mark ds3234_probe() __devinit while we're at it.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
For the time being build for ia64-sn2 alone when CONFIG_IA64_GENERIC is
specified.
This eliminates a dependency of the XP/XPC drivers on having the GRU
driver insmod'd in order to insmod them, when running on an ia64-sn2
system.
On such a system the GRU driver serves no useful purpose.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fixup i2o kernel-doc warnings:
Warning(linux-next-20081022//drivers/message/i2o/i2o_block.c:579): No description found for parameter 'bdev'
Warning(linux-next-20081022//drivers/message/i2o/i2o_block.c:579): No description found for parameter 'mode'
Warning(linux-next-20081022//drivers/message/i2o/i2o_block.c:608): No description found for parameter 'disk'
Warning(linux-next-20081022//drivers/message/i2o/i2o_block.c:608): No description found for parameter 'mode'
Warning(linux-next-20081022//drivers/message/i2o/i2o_block.c:657): No description found for parameter 'bdev'
Warning(linux-next-20081022//drivers/message/i2o/i2o_block.c:657): No description found for parameter 'mode'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
drivers/misc/hdpuftrs/hdpu_nexus.c:118: error: expected identifier or '(' before 'return'
drivers/misc/hdpuftrs/hdpu_nexus.c:119: error: expected identifier or '(' before '}' token
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
At least the Vaio VGN-Z540N doesn't have this method, so let's not fail
to suspend just because it doesn't exist.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Acked-by: Mattia Dongili <malattia@linux.it>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Updatescrollmode is marked inline, but it's big and is called only from
non-critical codepaths (fbcon_resize, fbcon_switch, fbcon_modechanged).
Dropping it saves almost 800 bytes of text size.
text data bss dec hex filename
23859 287 8448 32594 7f52 drivers/video/console/fbcon.o.before
23065 287 8448 31800 7c38 drivers/video/console/fbcon.o.after
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Antonino Daplas <adaplas@gmail.com>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The edac driver on cell turned out to be not enabled because of a missing
op_state. This patch introduces it. Verified to work on top of Ben's
next branch.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jens Osterkamp <jens@linux.vnet.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Warnings was appeared when compile rtc-s3c.c because
platform_driver structure s3c2410_rtcdrv has wrong name.
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Nothing uses prepare_write or commit_write. Remove them from the tree
completely.
[akpm@linux-foundation.org: schedule simple_prepare_write() for unexporting]
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I wrote a new module for Intel X38 chipset. This chipset is very similar
to Intel 3200 chipset, but there are some different points, so I copyed
i3200_edac.c and modified.
This is Intel's web page describing this chipset.
http://www.intel.com/Products/Desktop/Chipsets/X38/X38-overview.htm
I've tested this new module with broken memory, and it seems to be working
well.
Signed-off-by: Hitoshi Mitake <mitake@clustcom.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Removed duplicated #include's in drivers/video/via/global.h.
debug.h
viafbdev.h
viamode.h
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Cc: Joseph Chan <josephchan@via.com.tw>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
lockdep: fix irqs on/off ip tracing
lockdep: minor fix for debug_show_all_locks()
x86: restore the old swiotlb alloc_coherent behavior
x86: use GFP_DMA for 24bit coherent_dma_mask
swiotlb: remove panic for alloc_coherent failure
xen: compilation fix of drivers/xen/events.c on IA64
xen: portability clean up and some minor clean up for xencomm.c
xen: don't reload cr3 on suspend
kernel/resource: fix reserve_region_with_split() section mismatch
printk: remove unused code from kernel/printk.c
|
|
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] s390: Fix build for !CONFIG_S390_GUEST + CONFIG_VIRTIO_CONSOLE
[S390] No more 4kb stacks.
[S390] Change default IPL method to IPL_VM.
[S390] tape: disable interrupts in tape_open and tape_release
[S390] appldata: unsigned ops->size cannot be negative
[S390] tape block: complete request with correct locking
[S390] Fix sysdev class file creation.
[S390] pgtables: Fix race in enable_sie vs. page table ops
[S390] qdio: remove incorrect memset
[S390] qdio: prevent double qdio shutdown in case of I/O errors
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: ahci enclosure management bit mask
libata: ahci enclosure management led sync
pata_ninja32: suspend/resume support
libata: Fix LBA48 on pata_it821x RAID volumes.
libata: clear saved xfer_mode and ncq_enabled on device detach
sata_sil24: configure max read request size to 4k
libata: add missing kernel-doc
libata: fix device iteration bugs
ahci: Add support for Promise PDC42819
ata: Switch all my stuff to a common address
|
|
Get tape device lock with interrupts disabled. Otherwise lockdep will issue a
warning similar to:
=================================
[ INFO: inconsistent lock state ]
2.6.27 #1
---------------------------------
inconsistent {in-hardirq-W} -> {hardirq-on-W} usage.
vol_id/2903 [HC0[0]:SC0[0]:HE1:SE1] takes:
(sch->lock){++..}, at: [<000003e00004c7a2>] tape_open+0x42/0x1a4 [tape]
{in-hardirq-W} state was registered at:
[<000000000007ce5c>] __lock_acquire+0x894/0xa74
[<000000000007d0ce>] lock_acquire+0x92/0xb8
[<0000000000345154>] _spin_lock+0x5c/0x9c
[<0000000000202264>] do_IRQ+0x124/0x1f0
[<0000000000026610>] io_return+0x0/0x8
irq event stamp: 847
hardirqs last enabled at (847): [<000000000007aca6>] trace_hardirqs_on+0x2a/0x38
hardirqs last disabled at (846): [<0000000000076ca2>] trace_hardirqs_off+0x2a/0x38
softirqs last enabled at (0): [<000000000004909e>] copy_process+0x43e/0x11f4
softirqs last disabled at (0): [<0000000000000000>] 0x0
other info that might help us debug this:
1 lock held by vol_id/2903:
#0: (&bdev->bd_mutex){--..}, at: [<000000000010e0f4>] do_open+0x78/0x358
stack backtrace:
CPU: 1 Not tainted 2.6.27 #1},
Process vol_id (pid: 2903, task: 000000003d4c0000, ksp: 000000003d4e3b10)
0400000000000000 000000003d4e3830 0000000000000002 0000000000000000
000000003d4e38d0 000000003d4e3848 000000003d4e3848 00000000000168a8
0000000000000000 000000003d4e3b10 0000000000000000 0000000000000000
000000003d4e3830 000000000000000c 000000003d4e3830 000000003d4e38a0
000000000034aa98 00000000000168a8 000000003d4e3830 000000003d4e3880
Call Trace:
([<000000000001681c>] show_trace+0x138/0x158)
[<0000000000016902>] show_stack+0xc6/0xf8
[<00000000000170d4>] dump_stack+0xb0/0xc0
[<0000000000078810>] print_usage_bug+0x1e8/0x228
[<000000000007a71c>] mark_lock+0xb14/0xd24
[<000000000007cd5a>] __lock_acquire+0x792/0xa74
[<000000000007d0ce>] lock_acquire+0x92/0xb8
[<0000000000345154>] _spin_lock+0x5c/0x9c
[<000003e00004c7a2>] tape_open+0x42/0x1a4 [tape]
[<000003e00005185c>] tapeblock_open+0x98/0xd0 [tape]
Signed-off-by: Frank Munzert <munzert@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
__blk_end_request must be called with request queue lock held. We need to use
blk_end_request rather than __blk_end_request.
Signed-off-by: Frank Munzert <munzert@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Remove the memset since zeroing the string is not needed and use
snprintf instead of sprintf.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
In case of I/O errors on a qdio subchannel qdio_shutdown may be
called twice by the qdio driver and by zfcp. Remove the
superfluous shutdown from qdio and let the upper layer driver
handle the error condition.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Enclosure management bit mask definitions.
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Synchronize ahci_sw_activity and ahci_sw_activity_blink with ata_port lock.
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
I had assumed that the standard recovery would be sufficient for this
hardware but it isn't. Fix up the other registers on resume as needed. See
bug #11735
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
[http://lkml.org/lkml/2008/10/18/82]
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
libata EH saves xfer_mode and ncq_enabled at start to later set
DUBIOUS_XFER flag if it has changed. These values need to be cleared
on device detach such that hot device swap doesn't accidentally miss
DUBIOUS_XFER.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Due to request posting limitations, bandwidth of sil3132 is limited to
around 120MB/s with the minimum pci-e payload size (128bytes) which is
used by most consumer systems. However, write throughput can be
slightly (~3%) increased by increasing the max read requeset size.
Configure it to 4k which is the maximum supported. This optimization
is also done by SIMG's windows driver.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Fix libata missing kernel-doc:
Warning(lin2628-rc2//drivers/ata/libata-core.c:4562): No description
found for parameter 'tag'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
There were several places where only enabled devices should be
iterated over but device enabledness wasn't checked.
* IDENTIFY data 40 wire check in cable_is_40wire()
* xfer_mode/ncq_enabled saving in ata_scsi_error()
* DUBIOUS_XFER handling in ata_set_mode()
While at it, reformat comments in cable_is_40wire().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Add an appropriate entry for the Promise PDC42819 controller. It has an
AHCI mode and so far works correctly with board_ahci.
This chip is found on Promise's FastTrak TX2650 (2 port) and TX4650 (4 port)
software-based RAID cards (for which there is a binary driver, t3sas) and
can be found on some motherboards, for example the MSI K9A2 Platinum,
which calls the chip a Promise T3 controller.
Although this controller also supports SAS devices, its default bootup mode
is AHCI and the binary driver has to do some magic to get the chip into the
appropriate mode to drive SAS disks.
Seeing as no documentation is provided by Promise, adding this entry to the
ahci driver allows the controller to be useful to people as a SATA
controller (with no ill effects on the system if a SAS disk is connected -
probing of the port just times out with "link online but device
misclassified"), without having to resort to using the binary driver. Users
who require SAS or the proprietary software raid can get this functionality
using the binary driver.
Signed-off-by: Mark Nelson <mdnelson8@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
libata: fix NCQ devices behind port multipliers
scsi: make sure that scsi_init_shared_tag_map() doesn't overwrite existing map
|
|
For devices behind sata port multipliers, we have to make sure that
they share a tag map since all tags for that PMP must be unique.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (33 commits)
MIPS: lemote/lm2e: Added io_map_base to pci controller
MIPS: TXx9: Make firmware parameter passing more robust
MIPS: Markeins: Remove unnecessary define and cleanup comments, etc.
MIPS: Markeins: Extract ll_emma2rh_* functions
MIPS: Markeins: Remove runtime debug prints
MIPS: EMMA: Fold arch/mips/emma/{common,markeins}/irq*.c into markeins/irq.c
MIPS: EMMA2RH: Remove emma2rh_gpio_irq_base
MIPS: EMMA2RH: Remove emma2rh_sw_irq_base
MIPS: EMMA2RH: Remove emma2rh_irq_base global variable
MIPS: EMMA2RH: Remove emma2rh_sync on read operation
MIPS: EMMA: Move <asm/emma2rh> to <asm/emma> dir
MIPS: EMMA: Move arch/mips/emma2rh/ into arch/mips/emma/
MIPS: EMMA: Kconfig reorganization
MIPS: Add CONFIG_CPU_R5500 for NEC VR5500 series processors
MIPS: RB532: Disable the right device
MIPS: Add support for NXP PNX833x (STB222/5) into linux kernel
MIPS: TXx9: CONFIG_TOSHIBA_RBTX4939 spelling
MIPS: Fix KGDB build error
INPUT: sgi_btns: Add license specification
MIPS: IP22: ip22-int.c header file weeding.
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: fw-sbp2: fix races
firewire: fw-sbp2: delay first login to avoid retries
firewire: fw-ohci: initialization failure path fixes
firewire: fw-ohci: don't leak dma memory on module removal
firewire: fix struct fw_node memory leak
firewire: Survive more than 256 bus resets
|
|
The SGI Volume Button interface driver uses GPL-only symbols
platform_driver_unregister and platform_driver_register, but
lacks license specification. Thus, when compiled as a module,
this driver cannot be installed. This patch fixes this by
adding the MODULE_LICENSE() specification.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
syncookies: fix inclusion of tcp options in syn-ack
libertas: free sk_buff with kfree_skb
btsdio: free sk_buff with kfree_skb
Phonet: do not reply to indication reset packets
Phonet: include generic link-layer header size in MAX_PHONET_HEADER
|
|
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The leds-da903x LED driver was missing the proper #include of
linux/workqueue.h, but happened to compile on ARM due to implied
includes through other header files.
We do need the explict include on other architectures (reported at least
for x86-64).
Reported-tested-and-acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
free sk_buff with kfree_skb, instead of kree
Signed-off-by: Sergio Luis <sergio@larces.uece.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
free sk_buff with kfree_skb, instead of kree
Signed-off-by: Sergio Luis <sergio@larces.uece.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* 'for-linus' of git://neil.brown.name/md:
md: allow extended partitions on md devices.
md: use sysfs_notify_dirent to notify changes to md/dev-xxx/state
md: use sysfs_notify_dirent to notify changes to md/array_state
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: psmouse - add support for Elantech touchpads
Input: i8042 - add Blue FB5601 to noloop exception table
|
|
* 'for-linus' of git://git.o-hand.com/linux-mfd:
mfd: Make WM8400 depend on I2C until SPI is submitted
mfd: add missing Kconfig entry for da903x
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb
* 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb:
uwb: build UWB before USB/WUSB
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: Add support for Sony Vaio VGX-TP1E
HID: fix lock imbalance in hiddev
HID: fix lock imbalance in hidraw
HID: fix hidbus/appletouch device binding regression
HID: add hid_type to general hid struct
HID: quirk for OLED devices present in ASUS G50/G70/G71
HID: Remove "default m" for Thrustmaster and Zeroplus
HID: fix hidraw_exit section mismatch
HID: add support for another Gyration remote control
Revert "HID: Invert HWHEEL mappings for some Logitech mice"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
leds-hp-disk: fix build warning
ACPI: Oops in ACPI with git latest
ACPI suspend: build fix for ACPI_SLEEP=n && XEN_SAVE_RESTORE=y.
toshiba_acpi: always call input_sync() after input_report_switch()
ACPI: Always report a sync event after a lid state change
ACPI: cpufreq, processor: fix compile error in drivers/acpi/processor_perflib.c
i7300_idle: Fix compile warning CONFIG_I7300_IDLE_IOAT_CHANNEL not defined
i7300_idle: Cleanup based review comments
i7300_idle: Disable ioat channel only on platforms where ile driver can load
|
|
If CONFIG_AMIGA_BUILTIN_SERIAL=m, I get the following warnings:
| drivers/char/amiserial.c: At top level:
| drivers/char/amiserial.c:2138: warning: data definition has no type or storage class
| drivers/char/amiserial.c:2138: warning: type defaults to 'int' in declaration of 'console_initcall'
| drivers/char/amiserial.c:2138: warning: parameter names (without types) in function declaration
| drivers/char/amiserial.c:2134: warning: 'amiserial_console_init' defined but not used
because console_initcall() is not defined (nor really sensible) in the
modular case.
So disable serial console support if the driver is modular.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
hwmon: (abituguru3) enable DMI probing feature on AW9D-MAX
hwmon: (abituguru3) Cosmetic whitespace fixes
hwmon: (adt7473) Fix voltage conversion routines
hwmon: (lm90) Add support for the LM99 16 degree offset
hwmon: (lm90) Fix handling of hysteresis value
hwmon-vid: Add support for AMD family 10h CPUs
hwmon: (w83781d) Fix linking when built-in
|
|
This reverts commit 7bf6bf4803df1adc927f585168d2135fb019c698.
The code has both a short existence and an increasing track of failures
despite some work to amend it for -rc1. It is not just a matter of
reading the eeprom: sometimes the eeprom is read correctly, then the mac
address is not written correctly back into the mac registers.
Some chipsets seem to work reliably but it is not clear at this point if
the code can simply be made to work on a per-chipset basis and post -rc1
is not the place where I want to experiment these things.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
a) semicolon before the function body is a bad idea
b) it's const struct foo, not struct const foo
c) incidentally, it's ecard_remove_driver(), not ecard_unregister_driver()
d) compiling is occasionally useful.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Switch the AW9D-MAX over from port probing to the preferred DMI
probe method.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Tested-by: Justin Piszcz <jpiszcz@lucidpixels.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
As the probable result of zealous copy/pasting, many supported boards
contain sensor names with trailing whitespace. Though this is not a
huge problem, it is inconsistent with other sensor names, and with
other similar hwmon drivers.
Additionally, the DMI nag message added in 2.6.27 was missing a
space between two sentence fragments -- might as well clean that up
too.
Doesn't alter any kernel text, just data.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Reported-by: Justin Piszcz <jpiszcz@lucidpixels.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
