| Age | Commit message (Collapse) | Author |
|---|
|
We currently oops with a divide error on starting a linear software
raid array consisting of at least two very small (< 500K) devices.
The bug is caused by the calculation of the hash table size which
tries to compute sector_div(sz, base) with "base" being zero due to
the small size of the component devices of the array.
Fix this by requiring the hash spacing to be at least one which
implies that also "base" is non-zero.
This bug has existed since about 2.6.14.
Cc: stable@kernel.org
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Adding a spare to a raid10 doesn't cause recovery to start.
This is due to an silly type in
commit 6c2fce2ef6b4821c21b5c42c7207cb9cf8c87eda
and so is a bug in 2.6.27 and .28-rc.
Thanks to Thomas Backlund for bisecting to find this.
Cc: Thomas Backlund <tmb@mandriva.org>
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
It turns out that it is only safe to call blkdev_ioctl when the device
is actually open (as ->bd_disk is set to NULL on last close). And it
is quite possible for do_md_stop to be called when the device is not
open. So discard the call to blkdev_ioctl(BLKRRPART) which was
added in
commit 934d9c23b4c7e31840a895ba4b7e88d6413c81f3
It is just as easy to call this ioctl from userspace when needed (on
mdadm -S) so leave it out of the kernel
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Attached is a driver for SMSC's LAN911x and LAN921x families of embedded
ethernet controllers.
There is an existing smc911x driver in the tree; this is intended to
replace it. Dustin McIntire (the author of the smc911x driver) has
expressed his support for switching to this driver.
This driver contains workarounds for all known hardware issues, and has
been tested on all flavours of the chip on multiple architectures.
This driver now uses phylib, so this patch also adds support for the
device's internal phy
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Bahadir Balban <Bahadir.Balban@arm.com>
Signed-off-by: Dustin Mcintire <dustin@sensoria.com>
Signed-off-by: Bill Gatliff <bgat@billgatliff.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
This patch removes some trailing whitespaces and spaces before tabs.
Signed-off-by: Hannes Hering <hering2@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The TX watchdog should trigger a reset, but a temperature/power alarm
should not as this is unlikely to solve the problem.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Add board monitoring to periodic work whenever link is down.
For SFE4001, report when a fault has caused the PHY to turn off.
For SFE4002, switch XFP PHY into low-power state in case of a fault.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The boot code that appears as a PCI expansion ROM on the SFC4000 is
stored in flash. Expose this as a standard MTD device to allow for
in-place upgrades.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Move flash and EEPROM partition boundary constants into spi.h and rename
them to be consistent.
Add a comment on the partitioning.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Due to a hardware bug, the originally assigned range cannot reliably
be used for boot configuration and must not be modifiable through
ethtool.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
This patch implements alternative aggregator selection policies
for 802.3ad. The existing policy, now termed "stable," selects the active
aggregator by greatest bandwidth, and only reselects a new aggregator
if the active aggregator is entirely disabled (no more ports or all ports
down).
This patch adds two new policies: bandwidth and count, selecting
the active aggregator by total bandwidth (like the stable policy) or by
the number of ports in the aggregator, respectively. These two policies
also differ from the stable policy in that they will reselect the active
aggregator when availability-related changes occur in the bond (e.g.,
link state change).
This permits "gang failover" within 802.3ad, allowing redundant
aggregators along parallel paths to always maintain the "best" aggregator
as the active aggregator (rather than having to wait for the active to
entirely fail).
This patch also updates the driver version to 3.5.0.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The current ALB function that processes incoming ARPs
does not handle traffic for VLANs configured above bonding. This causes
traffic on those VLANs to all be assigned the same slave. This patch
corrects that misbehavior by locating the bonding interface nested below
the VLAN interface.
Bug reported by Sven Anders <anders@anduras.de>, who also
tested an earlier version of this patch and confirmed that it resolved
the problem.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
This patch adds better IPv6 failover support for bonding devices,
especially when in active-backup mode and there are only IPv6 addresses
configured, as reported by Alex Sidorenko.
- Creates a new file, net/drivers/bonding/bond_ipv6.c, for the
IPv6-specific routines. Both regular bonds and VLANs over bonds
are supported.
- Adds a new tunable, num_unsol_na, to limit the number of unsolicited
IPv6 Neighbor Advertisements that are sent on a failover event.
Default is 1.
- Creates two new IPv6 neighbor discovery functions:
ndisc_build_skb()
ndisc_send_skb()
These were required to support VLANs since we have to be able to
add the VLAN id to the skb since ndisc_send_na() and friends
shouldn't be asked to do this. These two routines are basically
__ndisc_send() split into two pieces, in a slightly different order.
- Updates Documentation/networking/bonding.txt and bumps the rev of bond
support to 3.4.0.
On failover, this new code will generate one packet:
- An unsolicited IPv6 Neighbor Advertisement, which helps the switch
learn that the address has moved to the new slave.
Testing has shown that sending just the NA results in pretty good
behavior when in active-back mode, I saw no lost ping packets for example.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
I was recently hunting a bug that occurred in network namespace
cleanup. In looking at the code it became apparrent that we have
and will continue to have cases where if we have anything going
on in a network namespace there will be assumptions that the
loopback device is present. Things like sending igmp unsubscribe
messages when we bring down network devices invokes the routing
code which assumes that at least the loopback driver is present.
Therefore to avoid magic initcall ordering hackery that is hard
to follow and hard to get right insert a call to register the
loopback device directly from net_dev_init(). This guarantes
that the loopback device is the first device registered and
the last network device to go away.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For "unlock" cycles to 16bit devices in 8bit compatibility mode we need
to use the byte addresses 0xaaa and 0x555. These effectively match
the word address 0x555 and 0x2aa, except the latter has its low bit set.
Most chips don't care about the value of the 'A-1' pin in x8 mode,
but some -- like the ST M29W320D -- do. So we need to be careful to
set it where appropriate.
cfi_send_gen_cmd is only ever passed addresses where the low byte
is 0x00, 0x55 or 0xaa. Of those, only addresses ending 0xaa are
affected by this patch, by masking in the extra low bit when the device
is known to be in compatibility mode.
[dwmw2: Do it only when (cmd_ofs & 0xff) == 0xaa]
v4: Fix stupid typo in cfi_build_cmd_addr that failed to compile
I'm writing this patch way to late at night.
v3: Bring all of the work back into cfi_build_cmd_addr
including calling of map_bankwidth(map) and cfi_interleave(cfi)
So every caller doesn't need to.
v2: Only modified the address if we our device_type is larger than our
bus width.
Cc: stable@kernel.org
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Compiling with CONFIG_SMP = n and CONFIG_PS3_LPM != n gives this error:
drivers/ps3/ps3-lpm.c:838: error: implicit declaration of function 'get_hard_smp_processor_id'
This fixes it. We have to include <asm/smp.h> rather than
<linux/smp.h> because the UP definition of get_hard_smp_processor_id()
is in <asm/smp.h>, and <linux/smp.h> only includes <asm/smp.h> if
CONFIG_SMP = y.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
xfrm: Fix xfrm_policy_gc_lock handling.
niu: Use pci_ioremap_bar().
bnx2x: Version Update
bnx2x: Calling netif_carrier_off at the end of the probe
bnx2x: PCI configuration bug on big-endian
bnx2x: Removing the PMF indication when unloading
mv643xx_eth: fix SMI bus access timeouts
net: kconfig cleanup
fs_enet: fix polling
XFRM: copy_to_user_kmaddress() reports local address twice
SMC91x: Fix compilation on some platforms.
udp: Fix the SNMP counter of UDP_MIB_INERRORS
udp: Fix the SNMP counter of UDP_MIB_INDATAGRAMS
drivers/net/smc911x.c: Fix lockdep warning on xmit.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: mask off DET when restoring SControl for detach
libata: implement ATA_HORKAGE_ATAPI_MOD16_DMA and apply it
libata: Fix a potential race condition in ata_scsi_park_show()
sata_nv: fix generic, nf2/3 detection regression
sata_via: restore vt*_prepare_host error handling
sata_promise: add ATA engine reset to reset ops
|
|
Signed-off-by: Jianjun Kong <jianjun@zeuux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
libata restores SControl on detach; however, trying to restore
non-zero DET can cause undeterministic behavior including PMP device
going offline till power cycling. Mask off DET when restoring
SControl.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
libata always uses PIO for ATAPI commands when the number of bytes to
transfer isn't multiple of 16 but quantum DAT72 chokes on odd bytes
PIO transfers. Implement a horkage to skip the mod16 check and apply
it to the quantum device.
This is reported by John Clark in the following thread.
http://thread.gmane.org/gmane.linux.ide/34748
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: John Clark <clarkjc@runbox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Peter Moulder has pointed out that there is a slight chance that a
negative value might be passed to jiffies_to_msecs() in
ata_scsi_park_show(). This is fixed by saving the value of jiffies in a
local variable, thus also reducing code since the volatile variable
jiffies is accessed only once.
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: Tejun Heo <tj.kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
All three flavors of sata_nv's are different in how their hardreset
behaves.
* generic: Hardreset is not reliable. Link often doesn't come online
after hardreset.
* nf2/3: A little bit better - link comes online with longer debounce
timing. However, nf2/3 can't reliable wait for the first D2H
Register FIS, so it can't wait for device readiness or classify the
device after hardreset. Follow-up SRST required.
* ck804: Hardreset finally works.
The core layer change to prefer hardreset and follow up changes
exposed the above issues and caused various detection regressions for
all three flavors. This patch, hopefully, fixes all the known issues
and should make sata_nv error handling more reliable.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
commit b9d5b89b487517cbd4cb4702da829e07ef9e4432 (sata_via: fix support
for 5287) accidently (?) removed vt*_prepare_host error handling - restore it
catched by gcc:
drivers/ata/sata_via.c: In function 'svia_init_one':
drivers/ata/sata_via.c:567: warning: 'host' may be used uninitialized in this function
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Promise ATA engines need to be reset when errors occur.
That's currently done for errors detected by sata_promise itself,
but it's not done for errors like timeouts detected outside of
the low-level driver.
The effect of this omission is that a timeout tends to result
in a sequence of failed COMRESETs after which libata EH gives
up and disables the port. At that point the port's ATA engine
hangs and even reloading the driver will not resume it.
To fix this, make sata_promise override ->hardreset on SATA
ports with code which calls pdc_reset_port() on the port in
question before calling libata's hardreset. PATA ports don't
use ->hardreset, so for those we override ->softreset instead.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Drivers need not do it any more.
Some cases had to be skipped over because the drivers
were making use of the ->last_rx value themselves.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The only user of the net_device->last_rx field is bonding.
This patch adds a conditional update of last_rx to the bonding special
logic in skb_bond_should_drop, causing last_rx to only be updated when
the ARP monitor is running.
This frees network device drivers from the necessity of
updating last_rx, which can have cache line thrash issues.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch updates the version to 3.95.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the BCM50610 to the list of phys supported by the
broadcom driver.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch makes the expansion register access routines a little more
formal. They will be used by the following bcm50610 support patch.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds flow control support to Broadcom phys.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch refines support for the 5785 device.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch refines the phylib support in the tg3 driver. The patch does
the following things :
* Rename tg3_mdio_config() to tg3_mdio_config_5785(). The 5785 will be
the only device that will use it so the name might as well reflect
that.
* Fix a memory leak if mdiobus_register() fails.
* Add code to deal with phy device detection failures.
* Add code to correct the supported list of phy features based on the
MAC <=> PHY interface.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch allows WOL to be enabled for Broadcom phys under phylib
control. The only exception is the AC131, which has a completely
different register set.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 12dac0756d357325b107fe6ec24921ec38661839 ("tg3: adapt tg3 to
use reworked PCI PM code") introduced the new PCI PM API to the tg3
driver. The patch was understandably conservative, so this patch
elaborates on that work.
The patch starts by creating a single point in tg3_set_power_state()
to decide whether or not to enable WOL. The rest of the code in
tg3_set_power_state() was then pivoted to use the result of this
decision.
The patch then makes sure the device is allowed to wakeup before
reporting whether or not WOL is currently enabled. The final hunks of
the patch consolidate where the WOL capability and WOL enabled flags
are set to a single location.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, phylib reports appear with a eth%d prefix. Move the line
after register_netdev() and place it alongside the other informative
messages. Update nearby informative messages accordingly.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With older versions of the NVRAM format, the driver may mistakenly
determine that APE is enabled. Make sure this doesn't happen by
restricting the ENABLE_APE check to devices known to have more
recent NVRAM image formats.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch reclaims the TG3_FLG3_5761_5784_AX_FIXES flag. It only
used twice in non-fast paths. This patch also consolidates some other
places where specific 5784 AX chip revisions can be generalized.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch moves the __tg3_set_mac_addr() function earlier in the file
listing, to avoid a function prototype, and calls the function to
restore the LAA after a driver unload chip reset. With this code in
place, the administrator can wake the machine using the LAA.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DASH firmware runs on the APE side of the chip, but it requires a few MAC
to be programmed correctly.
When WOL is enabled and management firmware is disabled, incoming
packets are evaluated and discarded at the chip's rule processor.
When management firmware is enabled, the hardware must be informed that
there are agents further up the stack that still use the incoming
frames. Normally management firmware will configure the MAC correctly
on its own, but there can be cases where the setting could get clobbered
by the driver. The first hunk of this patch preserves this setting.
The second hunk of this patch wipes out the driver present signature of
the APE memory space. By doing so, the DASH firmware can assume
driver absent behavior.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch replaces the existing APE register mapping code with a call
to pci_ioremap_bar(). The code that maps the main device register space
did not undergo a similar change because the information derived from
the pci_resource_start() and pci_resource_len() is still used to
populate the (optional) mem_start and mem_end netdevice members.
Replace hardcoded constants where appropriate.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for the 5761S chip variants.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Updating the version
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netif_carrier_off was called too early at the probe. In case of failure
or simply bad timing, this can cause a fatal error since linkwatch_event
might run too soon.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current code read nothing but zeros on big-endian (wrong part of the
32bits). This caused poor performance on big-endian machines. Though this
issue did not cause the system to crash, the performance is significantly
better with the fix so I view it as critical bug fix.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the PMF flag is set, the driver can access the HW freely. When the
driver is unloaded, it should not access the HW. The problem caused fatal
errors when "ethtool -i" was called after the calling instance was unloaded
and another instance was already loaded
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mv643xx_eth mii bus implementation uses wait_event_timeout() to
wait for SMI completion interrupts.
If wait_event_timeout() would return zero, mv643xx_eth would conclude
that the SMI access timed out, but this is not necessarily true --
wait_event_timeout() can also return zero in the case where the SMI
completion interrupt did happen in time but where it took longer than
the requested timeout for the process performing the SMI access to be
scheduled again. This would lead to occasional SMI access timeouts
when the system would be under heavy load.
The fix is to ignore the return value of wait_event_timeout(), and
to re-check the SMI done bit after wait_event_timeout() returns to
determine whether or not the SMI access timed out.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The bool kconfig option added to ixgbe and myri10ge for DCA is ambigous,
so this patch adds a description to the kconfig option.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
1. compile fix for irqreturn_t type change
2. restore ->poll_controller after CONFIG_PPC_CPM_NEW_BINDING transition
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
