aboutsummaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2008-10-27libata: Fix LBA48 on pata_it821x RAID volumes.Ondrej Zary
[http://lkml.org/lkml/2008/10/18/82] Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-27libata: clear saved xfer_mode and ncq_enabled on device detachTejun Heo
libata EH saves xfer_mode and ncq_enabled at start to later set DUBIOUS_XFER flag if it has changed. These values need to be cleared on device detach such that hot device swap doesn't accidentally miss DUBIOUS_XFER. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-27sata_sil24: configure max read request size to 4kTejun Heo
Due to request posting limitations, bandwidth of sil3132 is limited to around 120MB/s with the minimum pci-e payload size (128bytes) which is used by most consumer systems. However, write throughput can be slightly (~3%) increased by increasing the max read requeset size. Configure it to 4k which is the maximum supported. This optimization is also done by SIMG's windows driver. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-27libata: add missing kernel-docRandy Dunlap
Fix libata missing kernel-doc: Warning(lin2628-rc2//drivers/ata/libata-core.c:4562): No description found for parameter 'tag' Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-27libata: fix device iteration bugsTejun Heo
There were several places where only enabled devices should be iterated over but device enabledness wasn't checked. * IDENTIFY data 40 wire check in cable_is_40wire() * xfer_mode/ncq_enabled saving in ata_scsi_error() * DUBIOUS_XFER handling in ata_set_mode() While at it, reformat comments in cable_is_40wire(). Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-27ahci: Add support for Promise PDC42819Mark Nelson
Add an appropriate entry for the Promise PDC42819 controller. It has an AHCI mode and so far works correctly with board_ahci. This chip is found on Promise's FastTrak TX2650 (2 port) and TX4650 (4 port) software-based RAID cards (for which there is a binary driver, t3sas) and can be found on some motherboards, for example the MSI K9A2 Platinum, which calls the chip a Promise T3 controller. Although this controller also supports SAS devices, its default bootup mode is AHCI and the binary driver has to do some magic to get the chip into the appropriate mode to drive SAS disks. Seeing as no documentation is provided by Promise, adding this entry to the ahci driver allows the controller to be useful to people as a SATA controller (with no ill effects on the system if a SAS disk is connected - probing of the port just times out with "link online but device misclassified"), without having to resort to using the binary driver. Users who require SAS or the proprietary software raid can get this functionality using the binary driver. Signed-off-by: Mark Nelson <mdnelson8@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-27ata: Switch all my stuff to a common addressAlan Cox
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-27p54: fix build warningsChristian Lamparter
On Saturday 25 October 2008 10:24:10 Johannes Berg wrote: > just FYI in case you haven't seen them. the p54 one looks like a genuine > problem. > > drivers/net/wireless/p54/p54common.c: In function ‘p54_parse_eeprom’: > drivers/net/wireless/p54/p54common.c:325: warning: ‘synth’ may be used uninitialized in this function There you go. Yes, it is a genuine problem, if the device's eeprom is screwed really up. Signed-off-by: Christian Lamparter <chunkeey@web.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-10-27ath5k: Reset key cache on interface up, thus fixing resumeElias Oltmanns
After a s2ram / resume cycle, resetting the key cache does not work unless it is deferred until after the hardware has been reinitialised by a call to ath5k_hw_reset(). This fixes a regression introduced by "ath5k: fix suspend-related oops on rmmod". Signed-off-by: Elias Oltmanns <eo@nebensachen.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-10-27p54: fix misbehavings when firmware can't be foundChristian Lamparter
This patch fixes a double-free error in p54pci ( http://bugzilla.kernel.org/show_bug.cgi?id=11782 ) Trying to free already-free IRQ 10 Pid: 108, comm: pccardd Not tainted 2.6.27-05577-g0cfd810-dirty #1 Call Trace:  [<c01265dc>] free_irq+0xad/0xb9  [<c01050dd>] dma_generic_alloc_coherent+0x0/0xd7  [<c01ba8e6>] p54p_stop+0x4a/0x1fa  [<c01050dd>] dma_generic_alloc_coherent+0x0/0xd7  [<c02348c5>] p54p_probe+0x23e/0x302 Tested-by: Sean Young Signed-off-by: Christian Lamparter <chunkeey@web.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-10-27dm9601: runtime mac address change supportPeter Korsgaard
Implement set_mac_address for runtime mac address change. Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-27via-velocity: use driver string instead of dev->name before register_netdev()Sven Hartge
This patch corrects a message bug in the via-velocity driver which bothered me for some time. The messages printed during device init look like the following: [ 8.486422] eth%d: set value of parameter Wake On Lan options to 0 ^^! [ 8.487340] eth0: VIA Networking Velocity Family Gigabit Ethernet Adapter Note the unresolved format string. dev->name is unavailable before register_netdev, so use dev_driver_string(&pdev->dev), which is also consistent with other drivers. "char *devname" parameters had to be converted to "const char *devname" to be consistent with dev_driver_string return value. Signed-off-by: Sven Hartge <sven@svenhartge.de> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-27drivers/net/wan/syncppp: Fix unused-var warningsJeff Garzik
Fix !CONFIG_INET warnings. Spotted, and original patch authored by: Manish Katiyar <mkatiyar@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-27mlx4: Setting the correct offset for default mac addressYevgeny Petrilin
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-27mlx4_en: remove duplicated #includeHuang Weiyi
Removed duplicated #include <linux/cpumask.h> in drivers/net/mlx4/en_main.c. Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-27ibm_newemac: Fix typo in flow control config optionJosh Boyer
The recent build fix for ibm_newemac has a typo in the config option #ifdef used for disabling flow control. This corrects it to the proper Kconfig option name. Reported-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-27ehea: Detect 16GB hugepages for firmware restrictionThomas Klein
All kernel memory which is used for kernel/hardware data transfer must be registered with firmware using "memory regions". 16GB hugepages may not be part of a memory region due to firmware restrictions. This patch modifies the walk_memory_resource callback fn to filter hugepages and add only standard memory to the busmap which is later on used for MR registration. Signed-off-by: Thomas Klein <tklein@de.ibm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-27dmfe: check pci_alloc_consistent errorsFUJITA Tomonori
We need to check the address that pci_alloc_consistent() returns since it might fail. Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-27qeth: avoid skb_under_panic for malformatted inbound dataUrsula Braun
To make the qeth driver more robust in case of malformatted inbound packets due to hardware problems, an additional check for OSN-card-type is added for OSN-type packets. Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-27qeth: remove unnecessary support ckeck in sysfs route6Frank Blaschka
Removing this check improves usability because you do not have to set the device online to initially set ipv6 routing option. Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-27qeth: fix offset error in non prealloc header pathFrank Blaschka
For the non preallocated qeth header code path we should not change the header length. Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-27qeth: remove non-recover-thread checkingsUrsula Braun
IP-threads have been removed from the qeth driver. Only the recover-thread is left over. This makes checkings for non-recover threads superfluous. Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-27Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-blockLinus Torvalds
* 'for-linus' of git://git.kernel.dk/linux-2.6-block: libata: fix NCQ devices behind port multipliers scsi: make sure that scsi_init_shared_tag_map() doesn't overwrite existing map
2008-10-27libata: fix NCQ devices behind port multipliersJens Axboe
For devices behind sata port multipliers, we have to make sure that they share a tag map since all tags for that PMP must be unique. Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-10-27Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linusLinus Torvalds
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (33 commits) MIPS: lemote/lm2e: Added io_map_base to pci controller MIPS: TXx9: Make firmware parameter passing more robust MIPS: Markeins: Remove unnecessary define and cleanup comments, etc. MIPS: Markeins: Extract ll_emma2rh_* functions MIPS: Markeins: Remove runtime debug prints MIPS: EMMA: Fold arch/mips/emma/{common,markeins}/irq*.c into markeins/irq.c MIPS: EMMA2RH: Remove emma2rh_gpio_irq_base MIPS: EMMA2RH: Remove emma2rh_sw_irq_base MIPS: EMMA2RH: Remove emma2rh_irq_base global variable MIPS: EMMA2RH: Remove emma2rh_sync on read operation MIPS: EMMA: Move <asm/emma2rh> to <asm/emma> dir MIPS: EMMA: Move arch/mips/emma2rh/ into arch/mips/emma/ MIPS: EMMA: Kconfig reorganization MIPS: Add CONFIG_CPU_R5500 for NEC VR5500 series processors MIPS: RB532: Disable the right device MIPS: Add support for NXP PNX833x (STB222/5) into linux kernel MIPS: TXx9: CONFIG_TOSHIBA_RBTX4939 spelling MIPS: Fix KGDB build error INPUT: sgi_btns: Add license specification MIPS: IP22: ip22-int.c header file weeding. ...
2008-10-27Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6 * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: firewire: fw-sbp2: fix races firewire: fw-sbp2: delay first login to avoid retries firewire: fw-ohci: initialization failure path fixes firewire: fw-ohci: don't leak dma memory on module removal firewire: fix struct fw_node memory leak firewire: Survive more than 256 bus resets
2008-10-27INPUT: sgi_btns: Add license specificationDmitri Vorobiev
The SGI Volume Button interface driver uses GPL-only symbols platform_driver_unregister and platform_driver_register, but lacks license specification. Thus, when compiled as a module, this driver cannot be installed. This patch fixes this by adding the MODULE_LICENSE() specification. Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-10-27Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: syncookies: fix inclusion of tcp options in syn-ack libertas: free sk_buff with kfree_skb btsdio: free sk_buff with kfree_skb Phonet: do not reply to indication reset packets Phonet: include generic link-layer header size in MAX_PHONET_HEADER
2008-10-27Tidy up addresses in random driversAlan Cox
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-27leds: da903x: fix the building failure of incomplete type of 'work'Eric Miao
The leds-da903x LED driver was missing the proper #include of linux/workqueue.h, but happened to compile on ARM due to implied includes through other header files. We do need the explict include on other architectures (reported at least for x86-64). Reported-tested-and-acked-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-27HID: sync on deleted io_retry timer in usbhid driverJiri Slaby
When suspending, make sure that the timer is not running any more. Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2008-10-27HID: fix oops during suspend of unbound HID devicesJiri Slaby
Usbhid structure is allocated on start invoked only from probe of some driver. When there is no driver, the structure is null and causes null-dereference oopses. Fix it by allocating the structure on probe and disconnect of the device itself. Also make sure we won't race between start and resume or stop and suspend respectively. References: http://bugzilla.kernel.org/show_bug.cgi?id=11827 Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: Andreas Schwab <schwab@suse.de> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2008-10-26libertas: free sk_buff with kfree_skbSergio Luis
free sk_buff with kfree_skb, instead of kree Signed-off-by: Sergio Luis <sergio@larces.uece.br> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-26btsdio: free sk_buff with kfree_skbSergio Luis
free sk_buff with kfree_skb, instead of kree Signed-off-by: Sergio Luis <sergio@larces.uece.br> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-26Merge branch 'for-linus' of git://neil.brown.name/mdLinus Torvalds
* 'for-linus' of git://neil.brown.name/md: md: allow extended partitions on md devices. md: use sysfs_notify_dirent to notify changes to md/dev-xxx/state md: use sysfs_notify_dirent to notify changes to md/array_state
2008-10-26Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: psmouse - add support for Elantech touchpads Input: i8042 - add Blue FB5601 to noloop exception table
2008-10-26Merge branch 'for-linus' of git://git.o-hand.com/linux-mfdLinus Torvalds
* 'for-linus' of git://git.o-hand.com/linux-mfd: mfd: Make WM8400 depend on I2C until SPI is submitted mfd: add missing Kconfig entry for da903x
2008-10-26Merge branch 'for-upstream' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb * 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb: uwb: build UWB before USB/WUSB
2008-10-26Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: HID: Add support for Sony Vaio VGX-TP1E HID: fix lock imbalance in hiddev HID: fix lock imbalance in hidraw HID: fix hidbus/appletouch device binding regression HID: add hid_type to general hid struct HID: quirk for OLED devices present in ASUS G50/G70/G71 HID: Remove "default m" for Thrustmaster and Zeroplus HID: fix hidraw_exit section mismatch HID: add support for another Gyration remote control Revert "HID: Invert HWHEEL mappings for some Logitech mice"
2008-10-26Merge branch 'release' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6 * 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: leds-hp-disk: fix build warning ACPI: Oops in ACPI with git latest ACPI suspend: build fix for ACPI_SLEEP=n && XEN_SAVE_RESTORE=y. toshiba_acpi: always call input_sync() after input_report_switch() ACPI: Always report a sync event after a lid state change ACPI: cpufreq, processor: fix compile error in drivers/acpi/processor_perflib.c i7300_idle: Fix compile warning CONFIG_I7300_IDLE_IOAT_CHANNEL not defined i7300_idle: Cleanup based review comments i7300_idle: Disable ioat channel only on platforms where ile driver can load
2008-10-26m68k: Disable Amiga serial console support if modularGeert Uytterhoeven
If CONFIG_AMIGA_BUILTIN_SERIAL=m, I get the following warnings: | drivers/char/amiserial.c: At top level: | drivers/char/amiserial.c:2138: warning: data definition has no type or storage class | drivers/char/amiserial.c:2138: warning: type defaults to 'int' in declaration of 'console_initcall' | drivers/char/amiserial.c:2138: warning: parameter names (without types) in function declaration | drivers/char/amiserial.c:2134: warning: 'amiserial_console_init' defined but not used because console_initcall() is not defined (nor really sensible) in the modular case. So disable serial console support if the driver is modular. Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-26Merge branch 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6Linus Torvalds
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6: hwmon: (abituguru3) enable DMI probing feature on AW9D-MAX hwmon: (abituguru3) Cosmetic whitespace fixes hwmon: (adt7473) Fix voltage conversion routines hwmon: (lm90) Add support for the LM99 16 degree offset hwmon: (lm90) Fix handling of hysteresis value hwmon-vid: Add support for AMD family 10h CPUs hwmon: (w83781d) Fix linking when built-in
2008-10-26r8169: revert "read MAC address from EEPROM on init"Francois Romieu
This reverts commit 7bf6bf4803df1adc927f585168d2135fb019c698. The code has both a short existence and an increasing track of failures despite some work to amend it for -rc1. It is not just a matter of reading the eeprom: sometimes the eeprom is read correctly, then the mac address is not written correctly back into the mac registers. Some chipsets seem to work reliably but it is not clear at this point if the code can simply be made to work on a per-chipset basis and post -rc1 is not the place where I want to experiment these things. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-26arm ide breakageAl Viro
a) semicolon before the function body is a bad idea b) it's const struct foo, not struct const foo c) incidentally, it's ecard_remove_driver(), not ecard_unregister_driver() d) compiling is occasionally useful. Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-26hwmon: (abituguru3) enable DMI probing feature on AW9D-MAXAlistair John Strachan
Switch the AW9D-MAX over from port probing to the preferred DMI probe method. Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk> Tested-by: Justin Piszcz <jpiszcz@lucidpixels.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-26hwmon: (abituguru3) Cosmetic whitespace fixesAlistair John Strachan
As the probable result of zealous copy/pasting, many supported boards contain sensor names with trailing whitespace. Though this is not a huge problem, it is inconsistent with other sensor names, and with other similar hwmon drivers. Additionally, the DMI nag message added in 2.6.27 was missing a space between two sentence fragments -- might as well clean that up too. Doesn't alter any kernel text, just data. Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk> Reported-by: Justin Piszcz <jpiszcz@lucidpixels.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-26hwmon: (adt7473) Fix voltage conversion routinesJean Delvare
Fix voltage conversion routines. Based on an earlier patch from Paulius Zaleckas. According to the datasheet voltage is scaled with resistors and value 192 is nominal voltage. 0 is 0V. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Paulius Zaleckas <paulius.zaleckas@teltonika.lt> Cc: Darrick J. Wong <djwong@us.ibm.com>
2008-10-26hwmon: (lm90) Add support for the LM99 16 degree offsetJean Delvare
The LM99 differs from the LM86, LM89 and LM90 in that it reports remote temperatures (temp2) 16 degrees lower than they really are. So far we have been cheating and handled this in userspace but it really should be handled by the driver directly. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Matthew Garrett <mjg59@srcf.ucam.org>
2008-10-26hwmon: (lm90) Fix handling of hysteresis valueJean Delvare
There are several problems in the way the hysteresis value is handled by the lm90 driver: * In show_temphyst(), specific handling of the MAX6646 is missing, so the hysteresis is reported incorrectly if the critical temperature is over 127 degrees C. * In set_temphyst(), the new hysteresis register value is written to the chip but data->temp_hyst isn't updated accordingly, so there is a short period of time (up to 2 seconds) where the old hystereris value will be returned while the new one is already active. * In set_temphyst(), the critical temperature which is used as a base to compute the value of the hysteresis register lacks device-specific handling. As a result, the value of the hysteresis register might be incorrect for the ADT7461 and MAX6646 chips. Fix these 3 bugs. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Ben Hutchings <bhutchings@solarflare.com> Cc: Nate Case <ncase@xes-inc.com>
2008-10-26hwmon-vid: Add support for AMD family 10h CPUsJean Delvare
The AMD family 10h CPUs use the same VID decoding table as the family 0Fh CPUs. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Rudolf Marek <r.marek@assembler.cz>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-25 21:29:53 +0000