Age | Commit message (Collapse) | Author |
|
- Removed MSI support from driver - unused feature
- Replaced request_mem_region with pci_request_regions
Signed-off-by: Veena Parat <veena.parat@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
- Removed 3 buffer mode support from driver - unused feature
- Incorporated Jeff Garzik's comments on elimination of inline typecasting
- Code cleanup : Removed a few extra spaces
Signed-off-by: Veena Parat <veena.parat@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Some leftover code that makes use of adapter->lock in tx_timeout function,
which resets the interface under this lock. In close() when the workqueue
is flushed, prints the warning about sleeping with interrupts disabled
(when spinlock debug is enabled). The lock was required with private netxen
IOCTLs, which were removed a while ago.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This patch fixes masking of interrupts on multiport adapters. Also disables
interrupts upon ifdown interface. The wrong mask could result in interrupt
flood after interface is down.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This is a workaround for firmware bug with 2nd port of multiport adapter,
where MAC address is reset. Driver just needs to overwrite it with the
value read from PROM.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
In older chipsets, the mac address was stored in reversed order.
However, in newer chipsets, the mac address is in correct order. This
patch takes those newer chipsets into account and does not rely on a
special bit setup by BIOS'.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Fix the following modpost warning:
WARNING: vmlinux.o(.init.text+0x1aa6c): Section mismatch: reference to .exit.text:gfar_mdio_exit (between 'gfar_init' and 'gfar_mdio_init')
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Additional explanation of problems with locking by Alan Cox.
Signed-off-by: Jarek Poplawski <jarkao2@o2.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
drivers/net/usb/pegasus.c
This patch fixes a potential null dereference bug where we dereference
pegasus before a null check. This patch simply moves the dereferencing
after the null check.
Signed-off-by: Micah Gruber <micah.gruber@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The fcv1236d support patch was created before the "dvb: remove static
dependencies on dvb-pll" patch was applied, but the fcv1236d patch didn't
get merged until after the fact.
struct dvb_pll_fcv1236d can become static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
This patch:
- adds a missing error check and
- removes an error check that could never be true
Both spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Luca Olivetti <luca@ventoso.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
This patch removes the useless tuner field and avoids a double free of
the tuner (either mt2060 or qt1010).
Signed-off-by: Luca Olivetti <luca@ventoso.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
While decoding (MPEG or YUV) is active or when VBI output is in use, then
do not clear the VBI output of the saa7127. Only after the last user is
gone can we clear it.
This fixes the case where playback was stopped, another channel was chosen
and playback was restarted, while /dev/vbi16 was used to set the WSS
(widescreen) setting. Without this fix the WSS was reset on every stop
instead of just keeping the last value.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
First try polling for the result of a mailbox command, then
switch to a test/sleep loop. Also reduce the sleep time from 10 ms
to 1 ms. Improves the responsiveness of the mailbox handling.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Pausing a decoder followed by a Play command would do nothing. Fixed.
Pausing a decoder running at non-standard speed following by a Continue
would reset the speed to 100%. Fixed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
s_register was assigning the return code to (unsigned)reg->val, rather than
errCode, which it what it would return. Except reg->val can't be < 0, so it
would never actually return an error.
g_register never actually put the value it read into reg->val.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Various gpio and mux settings for the Osprey 440 weren't correct. Fix them
and provide some documentation about how the gpios work.
The osprey eeprom routine wasn't run for the 440, add it. It was also crap,
re-written to be better.
Add the Osprey 440 to the Bt878 ALSA driver's whitelist. Currently the sample
rate is fixed at 32kHz, as the driver doesn't support different rates for
digital input mode, though the card can select the rate from 32, 44.1, or 48
kHz via gpio.
Setting the audio gain via ALSA isn't supported yet; a userspace tool that
programs the X9221 via i2c-dev must be used.
The Bt878 digital audio format isn't programmed correctly for the CS5331A ADC
used, resulting in extremely garbled sound. That is fixed in a followup
patch.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
When raw capture was turned off, the current capturing frame (v4l_grab_frame)
wasn't reset to NO_GRAB_ACTIVE. If capture was turned back on, the driver
would think this frame was currently being captured, and wait for it to
complete before starting a new frame. The hardware on the other hand would
not be actively capturing a frame. The result was the driver would wait
forever for v4l_grab_frame to be captured.
Some calls to zr36057_set_memgrab(0) were missing spin-locks, which have been
added.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Add support for the UYVY and the other big endian output formats. The
driver was naming formats based on the host endianess. This is different
that all the other drivers appear to work and not what software appears
to expect.
Use ARRAY_SIZE() to find the the size of the zoran_formats array.
Change the way the driver handles setting the video format register. Rather
than use some if and switch statements to set to register by looking at the
format id, the format list simply has a field with the proper bits to set.
Adds a bit of ifdef to make a driver without V4L1 support more possible.
Also create a macro for defining formats that handles vl41 and/or vl42
support to avoid repeated ifdefs in the format list.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
The driver was returning the size of the (fixed) buffer it allocated as the
sizeimage field in the v4l2 pixel format, rather than the actual size of the
image. For example, a 192x128 YUYV image is 49152 bytes but the driver would
always return 131072 bytes since if that was the size of the v4l buffer.
This violates the v4l2 spec, which says that sizeimage should be the actual
size of the image for uncompressed formats. It also caused mplayer to crash.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
During uncompressed capture, the poll() function was looking the wrong frame.
It was using the frame the driver was going to capture into next (pend_tail),
when it should have been looking at the next frame to be de-queued with
DQBUF/SYNC (sync_tail).
It also wasn't looking in the right spot. It was looking at the file handle's
copy of the buffer status, rather than the driver core copy. The interrupt
routine marks frames as done in the driver core copy, the file handle copy
isn't updated. So even if poll() looked at the right frame, it would never
see it transition to done and return POLLIN.
The compressed capture code has this same problem, looking in fh->jpg_buffers
when it should have used zr->jpg_buffers.
There was some logic to detect when there was no current capture in process
nor any frames queued and try to return an error, which ends up being a bad
idea. It's possible to call select() from one thread while no capture is in
process, or no frames queued, and then start a capture or queue frames from
another thread.
The buffer state variables are protected by a spin lock, which the code wasn't
acquiring. That is fixed too.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
The zr36067 driver doesn't make a distinction between the different sub-types
of NTSC, PAL, or SECAM norms. For example, when the enum std ioctl returns
the PAL standard it returns PAL_BG|PAL_DK|PAL_H|PAL_I.
When setting the norm, it required the bitmask to match exactly the set of
norms used during the enumeration. If just one norm was specified, for
example PAL_BG or NTSC_M, it would fail. This violates the V4L2 spec,
"VIDIOC_S_STD accepts *one* or more flags..."
The key thing to realize is that V4L2_STD_PAL is not one bit, it is multiple
bits. It's ok to call S_STD with any *one* of those bits, but the driver was
requiring *all* of them.
This fixes the S_STD function so that it will accept any set of one or more
PAL norms as PAL, and the same for NTSC and SECAM.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Fix show_stack() when stack argument is NULL.
[SPARC]: Fix serial console node string creation.
[SPARC]: Mark SBUS framebuffer ioctls as IGNORE in compat_ioctl.c
[SPARC64]: asm-sparc64/floppy.h needs linux/pci.h
[SPARC64]: Fix conflicts in SBUS/PCI/EBUS/ISA DMA handling.
[VIDEO]: Fix OOPS in all SBUS framebuffer drivers.
[SPARC64]: Handle mostek clock type in mini_rtc driver.
[PARTITION]: Sun/Solaris VTOC table corrections
[SPARC]: Fix floppy on some sun4c systems.
[SPARC64]: Fix sun4u PCI config space accesses on sun4u.
[PARTITION] MSDOS: Fix Sun num_partitions handling.
[SPARC]: Update defconfig.
|
|
Added code to recognize the second interface on M5275 boards.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
On the MCF5272, there is no need to read the ICR before writing it :
the bit 4n+3 is a write-enable for the bits 4n,4n+1 and 4n+2.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix the work queue code in the FEC driver.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Removed unused CONFIG symbol and its conditional code from FEC driver.
Pointed out by Robert P. J. Day <rpjday@mindspring.com>.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Include cacheflush.h to get definitions for cache functions used
in this code.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
They are handled in a ->compat_ioctl() handler, so it's just noise
when compat_ioctl.c warns which occurs when they are used on non-SBUS
framebuffer devices.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fully unify all of the DMA ops so that subordinate bus types to
the DMA operation providers (such as ebus, isa, of_device) can
work transparently.
Basically, we just make sure that for every system device we
create, the dev->archdata 'iommu' and 'stc' fields are filled
in.
Then we have two platform variants of the DMA ops, one for SUN4U which
actually programs the real hardware, and one for SUN4V which makes
hypervisor calls.
This also fixes the crashes in parport_pc on sparc64, reported by
Meelis Roos.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All of these drivers use a silly:
struct all_info {
struct fb_info info;
struct foo_par par;
};
struct all_info *all = kzalloc(sizeof(*all), GFP_KERNEL);
all->info.par = &all->par;
etc. etc. code sequence, basically replicating the provided
framebuffer_alloc()/framebuffer_release(), and doing it badly.
Not only is this massive code duplication, it also caused a
bug in that we weren't setting the fb_info->device pointer
which results in an OOPS when fb_is_primary_device() runs.
Fix all of this by using framebuffer_{alloc,release}() and
passing in "&of_device->dev" as the device pointer.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Gabriel C reports lguest doesn't compile with CONFIG_BLOCK=n. Fix this
by introducing a config var for the block device, which depends on
LGUEST && BLOCK. Do the same for the net driver, rather then depending
gratuitously on CONFIG_NET.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Gabriel C <nix.or.die@googlemail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (28 commits)
[SCSI] mpt fusion: Changes in mptctl.c for logging support
[SCSI] mpt fusion: Changes in mptfc.c mptlan.c mptsas.c and mptspi.c for logging support
[SCSI] mpt fusion: Changes in mptscsih.c for logging support
[SCSI] mpt fusion: Changes in mptbase.c for logging support
[SCSI] mpt fusion: logging support in Kconfig, Makefile, mptbase.h and addition of mptdebug.h
[SCSI] libsas: Fix potential NULL dereference in sas_smp_get_phy_events()
[SCSI] bsg: Fix build for CONFIG_BLOCK=n
[SCSI] aacraid: fix Sunrise Lake reset handling
[SCSI] aacraid: add SCSI SYNCHONIZE_CACHE range checking
[SCSI] add easyRAID to the no report luns blacklist
[SCSI] advansys: lindent and other large, uninteresting changes
[SCSI] aic79xx, aic7xxx: Fix incorrect width setting
[SCSI] qla2xxx: fix to honor ignored parameters in sysfs attributes
[SCSI] aacraid: draw line in sand, sundry cleanup and version update
[SCSI] iscsi_tcp: Turn off bounce buffers
[SCSI] libiscsi: fix cmd seqeunce number checking
[SCSI] iscsi_tcp, ib_iser Enable module refcounting for iscsi host template
[SCSI] libiscsi: make sure session is not blocked when removing host
[SCSI] libsas: Remove PCI dependencies
[SCSI] simscsi: convert to use the data buffer accessors
...
|
|
Remove fs.h from mm.h. For this,
1) Uninline vma_wants_writenotify(). It's pretty huge anyway.
2) Add back fs.h or less bloated headers (err.h) to files that need it.
As result, on x86_64 allyesconfig, fs.h dependencies cut down from 3929 files
rebuilt down to 3444 (-12.3%).
Cross-compile tested without regressions on my two usual configs and (sigh):
alpha arm-mx1ads mips-bigsur powerpc-ebony
alpha-allnoconfig arm-neponset mips-capcella powerpc-g5
alpha-defconfig arm-netwinder mips-cobalt powerpc-holly
alpha-up arm-netx mips-db1000 powerpc-iseries
arm arm-ns9xxx mips-db1100 powerpc-linkstation
arm-assabet arm-omap_h2_1610 mips-db1200 powerpc-lite5200
arm-at91rm9200dk arm-onearm mips-db1500 powerpc-maple
arm-at91rm9200ek arm-picotux200 mips-db1550 powerpc-mpc7448_hpc2
arm-at91sam9260ek arm-pleb mips-ddb5477 powerpc-mpc8272_ads
arm-at91sam9261ek arm-pnx4008 mips-decstation powerpc-mpc8313_rdb
arm-at91sam9263ek arm-pxa255-idp mips-e55 powerpc-mpc832x_mds
arm-at91sam9rlek arm-realview mips-emma2rh powerpc-mpc832x_rdb
arm-ateb9200 arm-realview-smp mips-excite powerpc-mpc834x_itx
arm-badge4 arm-rpc mips-fulong powerpc-mpc834x_itxgp
arm-carmeva arm-s3c2410 mips-ip22 powerpc-mpc834x_mds
arm-cerfcube arm-shannon mips-ip27 powerpc-mpc836x_mds
arm-clps7500 arm-shark mips-ip32 powerpc-mpc8540_ads
arm-collie arm-simpad mips-jazz powerpc-mpc8544_ds
arm-corgi arm-spitz mips-jmr3927 powerpc-mpc8560_ads
arm-csb337 arm-trizeps4 mips-malta powerpc-mpc8568mds
arm-csb637 arm-versatile mips-mipssim powerpc-mpc85xx_cds
arm-ebsa110 i386 mips-mpc30x powerpc-mpc8641_hpcn
arm-edb7211 i386-allnoconfig mips-msp71xx powerpc-mpc866_ads
arm-em_x270 i386-defconfig mips-ocelot powerpc-mpc885_ads
arm-ep93xx i386-up mips-pb1100 powerpc-pasemi
arm-footbridge ia64 mips-pb1500 powerpc-pmac32
arm-fortunet ia64-allnoconfig mips-pb1550 powerpc-ppc64
arm-h3600 ia64-bigsur mips-pnx8550-jbs powerpc-prpmc2800
arm-h7201 ia64-defconfig mips-pnx8550-stb810 powerpc-ps3
arm-h7202 ia64-gensparse mips-qemu powerpc-pseries
arm-hackkit ia64-sim mips-rbhma4200 powerpc-up
arm-integrator ia64-sn2 mips-rbhma4500 s390
arm-iop13xx ia64-tiger mips-rm200 s390-allnoconfig
arm-iop32x ia64-up mips-sb1250-swarm s390-defconfig
arm-iop33x ia64-zx1 mips-sead s390-up
arm-ixp2000 m68k mips-tb0219 sparc
arm-ixp23xx m68k-amiga mips-tb0226 sparc-allnoconfig
arm-ixp4xx m68k-apollo mips-tb0287 sparc-defconfig
arm-jornada720 m68k-atari mips-workpad sparc-up
arm-kafa m68k-bvme6000 mips-wrppmc sparc64
arm-kb9202 m68k-hp300 mips-yosemite sparc64-allnoconfig
arm-ks8695 m68k-mac parisc sparc64-defconfig
arm-lart m68k-mvme147 parisc-allnoconfig sparc64-up
arm-lpd270 m68k-mvme16x parisc-defconfig um-x86_64
arm-lpd7a400 m68k-q40 parisc-up x86_64
arm-lpd7a404 m68k-sun3 powerpc x86_64-allnoconfig
arm-lubbock m68k-sun3x powerpc-cell x86_64-defconfig
arm-lusl7200 mips powerpc-celleb x86_64-up
arm-mainstone mips-atlas powerpc-chrp32
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Restore the 2.6.22 CONFIG_ACPI_SLEEP build option, but now shadowing the
new CONFIG_PM_SLEEP option.
Signed-off-by: Len Brown <len.brown@intel.com>
[ Modified to work with the PM config setup changes. ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Introduce CONFIG_SUSPEND representing the ability to enter system sleep
states, such as the ACPI S3 state, and allow the user to choose SUSPEND
and HIBERNATION independently of each other.
Make HOTPLUG_CPU be selected automatically if SUSPEND or HIBERNATION has
been chosen and the kernel is intended for SMP systems.
Also, introduce CONFIG_PM_SLEEP which is automatically selected if
CONFIG_SUSPEND or CONFIG_HIBERNATION is set and use it to select the
code needed for both suspend and hibernation.
The top-level power management headers and the ACPI code related to
suspend and hibernation are modified to use the new definitions (the
changes in drivers/acpi/sleep/main.c are, mostly, moving code to reduce
the number of ifdefs).
There are many other files in which CONFIG_PM can be replaced with
CONFIG_PM_SLEEP or even with CONFIG_SUSPEND, but they can be updated in
the future.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Replace CONFIG_SOFTWARE_SUSPEND with CONFIG_HIBERNATION to avoid
confusion (among other things, with CONFIG_SUSPEND introduced in the
next patch).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Make sure declarations stay in sync with definitions by keeping all
extern declarations in common .h files.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Remove extra dumb-looking blank line that snuck in somehow.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
A non-periodic clock_event_device and the "jiffies" clock don't mix well:
tick_handle_periodic() can go into an infinite loop.
Currently lguest guests use the jiffies clock when the TSC is
unusable. Instead, make the Host write the current time into the lguest
page on every interrupt. This doesn't cost much but is more precise
and at least as accurate as the jiffies clock. It also gets rid of
the GET_WALLCLOCK hypercall.
Also, delay setting sched_clock until our clock is set up, otherwise
the early printk timestamps can go backwards (not harmful, just ugly).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Jason Yeh sent his crashing .config: bzImages made with
CONFIG_RELOCATABLE=y put the relocs where the BSS is expected, and we
crash with unusual results such as:
lguest: unhandled trap 14 at 0xc0122ae1 (0xa9)
Relying on BSS being zero was merely laziness on my part, and
unfortunately, lguest doesn't go through the normal startup path (which
does this in asm).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] Fix sclp_vt220 error handling.
[S390] cio: Reorganize initialization.
[S390] cio: Make CIO_* macros safe if dbfs are not available.
[S390] cio: Clean up messages.
[S390] Fix IRQ tracing.
[S390] vmur: fix diag14_read.
[S390] Wire up sys_fallocate.
[S390] add types.h include to s390_ext.h
[S390] cio: Remove deprecated rdc/rcd.
[S390] Get rid of new section mismatch warnings.
[S390] sclp: kill unused SCLP config option.
[S390] cio: Remove remains of _ccw_device_get_device_number().
[S390] cio: css_sch_device_register() can be made static.
[S390] Improve __smp_call_function_map.
[S390] Convert to smp_call_function_single.
|
|
master.kernel.org:/pub/scm/linux/kernel/git/cooloney/blackfin-2.6
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
Input Serio: Blackfin doesnt support I8042 - make sure it doesnt get selected
Blackfin arch: add BF54x I2C/TWI TWI0 driver support
Blackfin On-Chip RTC driver update for supporting BF54x
Blackfin Ethernet MAC driver: fix bug Report returned -ENOMEM upwards (in case L1/uncached memory alloc fails)
Blackfin arch: add error message when IRQ no available
Blackfin arch: Initialize the exception vectors early in the boot process
Blackfin arch: fix a compiling warning about dma-mapping
Blackfin arch: switch to using proper defines this time THREAD_SIZE and PAGE_SIZE instead of just PAGE_SIZE everywhere
Blackfin arch: fix bug which unaligns the init thread's stack and causes the current macro to fail.
Blackfin arch: Load P0 before storing through it
Blackfin arch: fix KGDB bug, dont forget last parameter.
Blackfin arch: add selections for BF544 and BF542
Blackfin arch: use bfin_read_SWRST() now that BF561 provides it
Blackfin arch: setup aliases for some core Core A MMRs
|
|
Include <rdma/...> headers after <asm/...> headers.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
This patch contains changes in mptctl.c to support logging in MPT fusion drivers
The changes are majorly in debug printks, the existing debugprintk are
modified accroding to new debug macros defined in the file mptbdebug.h
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
logging support
This patch contains changes in mptfc.c, mptlan.c, mptsas.c and mptspi.c to
support logging in MPT fusion drivers.
The changes are majorly in debug printks, the existing debugprintk are
modified accroding to new debug macros defined in the file mptbdebug.h
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
mlx4_mr_alloc() doesn't actually allocate mr (it just initializes the
pointer that the caller passes in), so it shouldn't free it if an
error occurs.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
This patch contains changes in mptscsih.c to support logging in MPT fusion
drivers.
The changes are majorly in debug printks, the existing debugprintk are
modified accroding to new debug macros defined in the file mptbdebug.h
A new sysfs attribute is added to retrieve and modify the debug level.
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
This patch contains changes in mptbase.c to support logging in MPT fusion
drivers.
The changes are majorly in debug printks, the existing debugprintk are
modified accroding to new debug macros defined in the file mptbdebug.h
A new module parameter mpt_debug_level is added to pass the debug level as
module parameter.
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|