aboutsummaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2007-05-06[VIDEO]: Add Sun XVR-2500 framebuffer driver.David S. Miller
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-06[VIDEO]: Add Sun XVR-500 framebuffer driver.David S. Miller
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-06[SCSI] SUNESP: sun_esp.c needs linux/delay.hDavid S. Miller
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-06IPoIB: Convert to NAPIRoland Dreier
Convert the IP-over-InfiniBand network device driver over to using NAPI to handle completions for the main CQ. This covers all receives as well as datagram mode sends; send completions for connected mode connections are still handled from interrupt context. Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-05-06IB: Return "maybe missed event" hint from ib_req_notify_cq()Roland Dreier
The semantics defined by the InfiniBand specification say that completion events are only generated when a completions is added to a completion queue (CQ) after completion notification is requested. In other words, this means that the following race is possible: while (CQ is not empty) ib_poll_cq(CQ); // new completion is added after while loop is exited ib_req_notify_cq(CQ); // no event is generated for the existing completion To close this race, the IB spec recommends doing another poll of the CQ after requesting notification. However, it is not always possible to arrange code this way (for example, we have found that NAPI for IPoIB cannot poll after requesting notification). Also, some hardware (eg Mellanox HCAs) actually will generate an event for completions added before the call to ib_req_notify_cq() -- which is allowed by the spec, since there's no way for any upper-layer consumer to know exactly when a completion was really added -- so the extra poll of the CQ is just a waste. Motivated by this, we add a new flag "IB_CQ_REPORT_MISSED_EVENTS" for ib_req_notify_cq() so that it can return a hint about whether the a completion may have been added before the request for notification. The return value of ib_req_notify_cq() is extended so: < 0 means an error occurred while requesting notification == 0 means notification was requested successfully, and if IB_CQ_REPORT_MISSED_EVENTS was passed in, then no events were missed and it is safe to wait for another event. > 0 is only returned if IB_CQ_REPORT_MISSED_EVENTS was passed in. It means that the consumer must poll the CQ again to make sure it is empty to avoid the race described above. We add a flag to enable this behavior rather than turning it on unconditionally, because checking for missed events may incur significant overhead for some low-level drivers, and consumers that don't care about the results of this test shouldn't be forced to pay for the test. Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-05-06IB: Add CQ comp_vector supportMichael S. Tsirkin
Add a num_comp_vectors member to struct ib_device and extend ib_create_cq() to pass in a comp_vector parameter -- this parallels the userspace libibverbs API. Update all hardware drivers to set num_comp_vectors to 1 and have all ULPs pass 0 for the comp_vector value. Pass the value of num_comp_vectors to userspace rather than hard-coding a value of 1. We want multiple CQ event vector support (via MSI-X or similar for adapters that can generate multiple interrupts), but it's not clear how many vectors we want, or how we want to deal with policy issues such as how to decide which vector to use or how to set up interrupt affinity. This patch is useful for experimenting, since no core changes will be necessary when updating a driver to support multiple vectors, and we know that we want to make at least these changes anyway. Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-05-06IB/ipath: Fix a race condition when generating ACKsRalph Campbell
Fix a problem where simple ACKs can be sent ahead of RDMA read responses thus implicitly NAKing the RDMA read. Signed-off-by: Ralph Campbell <ralph.cambpell@qlogic.com> Signed-off-by: Robert Walsh <robert.walsh@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-05-06IB/ipath: Fix two more spin lock problemsRalph Campbell
Fix a missing unlock in ipath_rc_rcv_resp() and remove an extra unlock from ipath_rc_rcv_error(). Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-05-06IB/fmr_pool: Add prefix to all printksRoland Dreier
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-05-06IB/srp: Set proc_nameRoland Dreier
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-05-06IB/srp: Add orig_dgid sysfs attribute to scsi_hostIshai Rabinovitz
Add an orig_dgid attribute in sysfs for SRP scsi_hosts, so that userspace can tell what the original dgid value written to the add_target file was, even if the connection is redirected to a different port while connecting. Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-05-06IPoIB/cm: Don't crash if remote side uses one QP for both directionsMichael S. Tsirkin
The IPoIB CM spec allows the use of a single connection in both active->passive and passive->active directions. The current Linux code uses one connection for both directions, but if another node only uses one connection for both directions, we oops when we try to look up the passive connection. Fix by checking that qp_context is non-NULL before dereferencing it. Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
2007-05-06RDMA/cxgb3: Support for new abort logicSteve Wise
The HW now posts 2 ABORT_RPL and/or PEER_ABORT_REQ messages. We need to handle them by silenty dropping the 1st but mark that we're ready for the final message. This plugs some close races between the uP and HW. Also update the minimum required firmware version. Signed-off-by: Steve Wise <swise@opengridcomputing.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-05-07serial: sh-sci: Fix module clock refcount for serial console.Paul Mundt
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-05-07serial: sh-sci: Fix module clock refcounting.dmitry pervushin
This adds the enable/disable hooks for the port clock to sh-sci. Signed-off-by: dmitry pervushin <dimka@nomadgs.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-05-07sh: MS7712SE01 board support.Nobuhiro Iwamatsu
Support the SH7712 (SH3-DSP) Solution Engine reference board. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-05-07sh: hp6xx driver compile fixes.Kristoffer Ericson
Trivial compilation fixes for the hp6xx drivers. Signed-off-by: Kristoffer Ericson <Kristoffer_e1@hotmail.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-05-07serial: sh-sci: Kill off breakpoint in break IRQ.Paul Mundt
With the GDB stub being entered via a special sysrq trigger, we don't want to hit it directly from sci_br_interrupt(). Without this, there is access to the other sysrq triggers when kgdb is enabled. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-05-07sh: Add SH7785 Highlander board support (R7785RP).Paul Mundt
This adds preliminary support for the SH7785-based Highlander board. Some of the Highlander support code is reordered so that most of it can be reused directly. This also plugs in missing SH7785 checks in the places that need it, as this is the first board to support the CPU. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-05-07sh: Bring kgdb back from the dead.Paul Mundt
This code has suffered quite a bit of bitrot, do some basic tidying to get it to a reasonably functional state again. This gets the basic support and the console working again. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-05-06Merge git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuildLinus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (38 commits) kconfig: fix mconf segmentation fault kbuild: enable use of code from a different dir kconfig: error out if recursive dependencies are found kbuild: scripts/basic/fixdep segfault on pathological string-o-death kconfig: correct minor typo in Kconfig warning message. kconfig: fix path to modules.txt in Kconfig help usr/Kconfig: fix typo kernel-doc: alphabetically-sorted entries in index.html of 'htmldocs' kbuild: be more explicit on missing .config file kbuild: clarify the creation of the LOCALVERSION_AUTO string. kbuild: propagate errors from find in scripts/gen_initramfs_list.sh kconfig: refer to qt3 if we cannot find qt libraries kbuild: handle compressed cpio initramfs-es kbuild: ignore section mismatch warning for references from .paravirtprobe to .init.text kbuild: remove stale comment in modpost.c kbuild/mkuboot.sh: allow spaces in CROSS_COMPILE kbuild: fix make mrproper for Documentation/DocBook/man kbuild: remove kconfig binaries during make mrproper kconfig/menuconfig: do not hardcode '.config' kbuild: override build timestamp & version ...
2007-05-06Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm: (66 commits) KVM: Remove unused 'instruction_length' KVM: Don't require explicit indication of completion of mmio or pio KVM: Remove extraneous guest entry on mmio read KVM: SVM: Only save/restore MSRs when needed KVM: fix an if() condition KVM: VMX: Add lazy FPU support for VT KVM: VMX: Properly shadow the CR0 register in the vcpu struct KVM: Don't complain about cpu erratum AA15 KVM: Lazy FPU support for SVM KVM: Allow passing 64-bit values to the emulated read/write API KVM: Per-vcpu statistics KVM: VMX: Avoid unnecessary vcpu_load()/vcpu_put() cycles KVM: MMU: Avoid heavy ASSERT at non debug mode. KVM: VMX: Only save/restore MSR_K6_STAR if necessary KVM: Fold drivers/kvm/kvm_vmx.h into drivers/kvm/vmx.c KVM: VMX: Don't switch 64-bit msrs for 32-bit guests KVM: VMX: Reduce unnecessary saving of host msrs KVM: Handle guest page faults when emulating mmio KVM: SVM: Report hardware exit reason to userspace instead of dmesg KVM: Retry sleeping allocation if atomic allocation fails ...
2007-05-06Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (82 commits) [ARM] Add comments marking in-use ptrace numbers [ARM] Move syscall saving out of the way of utrace [ARM] 4360/1: S3C24XX: regs-udc.h remove unused macro [ARM] 4358/1: S3C24XX: mach-qt2410.c: remove linux/mmc/protocol.h header [ARM] mm 10: allow memory type to be specified with ioremap [ARM] mm 9: add additional device memory types [ARM] mm 8: define mem_types table L1 bit 4 to be for ARMv6 [ARM] iop: add missing parens in macro [ARM] mm 7: remove duplicated __ioremap() prototypes ARM: OMAP: fix OMAP1 mpuio suspend/resume oops ARM: OMAP: MPUIO wake updates ARM: OMAP: speed up gpio irq handling ARM: OMAP: plat-omap changes for 2430 SDP ARM: OMAP: gpio object shrinkage, cleanup ARM: OMAP: /sys/kernel/debug/omap_gpio ARM: OMAP: Implement workaround for GPIO wakeup bug in OMAP2420 silicon ARM: OMAP: Enable 24xx GPIO autoidling [ARM] 4318/2: DSM-G600 Board Support [ARM] 4227/1: minor head.S fixups [ARM] 4328/1: Move i.MX UART regs to driver ...
2007-05-06Merge branches 'arm-mm', 'at91', 'clkevts', 'imx', 'iop', 'misc', 'netx', ↵Russell King
'ns9xxx', 'omap', 'pxa', 'rpc', 's3c' and 'sa1100' into devel
2007-05-05Merge branch 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6Linus Torvalds
* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6: (231 commits) [PATCH] i386: Don't delete cpu_devs data to identify different x86 types in late_initcall [PATCH] i386: type may be unused [PATCH] i386: Some additional chipset register values validation. [PATCH] i386: Add missing !X86_PAE dependincy to the 2G/2G split. [PATCH] x86-64: Don't exclude asm-offsets.c in Documentation/dontdiff [PATCH] i386: avoid redundant preempt_disable in __unlazy_fpu [PATCH] i386: white space fixes in i387.h [PATCH] i386: Drop noisy e820 debugging printks [PATCH] x86-64: Fix allnoconfig error in genapic_flat.c [PATCH] x86-64: Shut up warnings for vfat compat ioctls on other file systems [PATCH] x86-64: Share identical video.S between i386 and x86-64 [PATCH] x86-64: Remove CONFIG_REORDER [PATCH] x86-64: Print type and size correctly for unknown compat ioctls [PATCH] i386: Remove copy_*_user BUG_ONs for (size < 0) [PATCH] i386: Little cleanups in smpboot.c [PATCH] x86-64: Don't enable NUMA for a single node in K8 NUMA scanning [PATCH] x86: Use RDTSCP for synchronous get_cycles if possible [PATCH] i386: Add X86_FEATURE_RDTSCP [PATCH] i386: Implement X86_FEATURE_SYNC_RDTSC on i386 [PATCH] i386: Implement alternative_io for i386 ... Fix up trivial conflict in include/linux/highmem.h manually. Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-05Fix compile of tmscsim SCSI driverLinus Torvalds
It still used the long-deprecated "pci_module_init()" interface, rather than the proper "pci_register_driver()" one. [ I don't have the hardware, and I doubt many do, but the fix is trivial and obvious, and can't be worse than not compiling ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-05Merge master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: [TG3]: Add TG3_FLAG_SUPPORT_MSI flag. [TG3]: Eliminate the TG3_FLAG_5701_REG_WRITE_BUG flag. [TG3]: Eliminate the TG3_FLAG_GOT_SERDES_FLOWCTL flag. [TG3]: Remove reset during MAC address changes. [TG3]: WoL fixes. [TG3]: Clear GPIO mask before storing. [TG3]: Improve NVRAM sizing. [TG3]: Fix TSO bugs. [MAC80211]: Add maintainers entry for mac80211. [MAC80211]: Add debugfs attributes. [MAC80211]: Add mac80211 wireless stack. [MAC80211]: Add generic include/linux/ieee80211.h [NETLINK]: Remove references to process ID [AF_IUCV]: Compile fix - adopt to skbuff changes.
2007-05-05Merge master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6Linus Torvalds
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (87 commits) [SCSI] fusion: fix domain validation loops [SCSI] qla2xxx: fix regression on sparc64 [SCSI] modalias for scsi devices [SCSI] sg: cap reserved_size values at max_sectors [SCSI] BusLogic: stop using check_region [SCSI] tgt: fix rdma transfer bugs [SCSI] aacraid: fix aacraid not finding device [SCSI] aacraid: Correct SMC products in aacraid.txt [SCSI] scsi_error.c: Add EH Start Unit retry [SCSI] aacraid: [Fastboot] Panics for AACRAID driver during 'insmod' for kexec test. [SCSI] ipr: Driver version to 2.3.2 [SCSI] ipr: Faster sg list fetch [SCSI] ipr: Return better qc_issue errors [SCSI] ipr: Disrupt device error [SCSI] ipr: Improve async error logging level control [SCSI] ipr: PCI unblock config access fix [SCSI] ipr: Fix for oops following SATA request sense [SCSI] ipr: Log error for SAS dual path switch [SCSI] ipr: Enable logging of debug error data for all devices [SCSI] ipr: Add new PCI-E IDs to device table ...
2007-05-05[TG3]: Add TG3_FLAG_SUPPORT_MSI flag.Michael Chan
And fix up the code to always allow MSI on 5714 A2. Call tg3_find_peer() earlier because we need that information before we can determine whether we can set TG3_FLAG_SUPPORT_MSI or not. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-05ide-cs: recognize 2GB CompactFlash from TranscendFabrice Aeschbacher
Without the following patch, the kernel does not automatically detect 2GB CompactFlash cards from Transcend. Signed-off-by: Fabrice Aeschbacher <fabrice.aeschbacher@siemens.com> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Acked-by: Peter Stuge <peter@stuge.se> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-05hpt366: don't check enablebits for HPT36xSergei Shtylyov
HPT36x chip don't seem to have the channel enable bits, so prevent the IDE core from checking them... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Michal Kepien <michal.kepien@poczta.onet.pl> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-05ide-cris: fix ->speedproc and wrong ->swdma_maskBartlomiej Zolnierkiewicz
* fix ->speedproc to set the drive speed * this driver doesn't support SWDMA so use the correct ->swdma_mask * BUG() if an unsupported mode is passed to ->speedproc Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-05siimage: fix wrong ->swdma_maskBartlomiej Zolnierkiewicz
This driver doesn't support SWDMA so use the correct ->swdma_mask. While at it: * no need to call config_chipset_for_pio() in config_chipset_for_dma(), if DMA is not available config_chipset_for_pio() will be called by siimage_config_drive_for_dma() and if DMA is available config_siimage_chipset_for_pio() will be called by siimage_tune_chipset() * remove needless config_chipset_for_pio() wrapper * bump driver version Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-05it821x: PIO mode setup fixesBartlomiej Zolnierkiewicz
* limit max PIO mode to PIO4, this driver doesn't support PIO5 and attempt to setup PIO5 by it821x_tuneproc() could result in incorrect PIO timings + incorrect base clock being set for controller in the passthrough mode * move code limiting max PIO according to the pair device capabilities from config_it821x_chipset_for_pio() to it821x_tuneproc() so the check is also applied for mode change requests coming through ->tuneproc and ->speedproc interfaces * set device speed in it821x_tuneproc() * in it821x_tune_chipset() call it821x_tuneproc() also if the controller is in the smart mode (so the check for pair device max PIO is done) * rename it821x_tuneproc() to it821x_tune_pio(), then add it821x_tuneproc() wrapper which does the max PIO mode check; it worked by the pure luck previously, pio[4] and pio_want[4] arrays were used with index == 255 so random PIO timings and base clock were set for the controller in the passthrough mode, thankfully PIO timings and base clock were corrected later by config_it821x_chipset_for_pio() call (but it was not called for PIO-only devices during resume and for user requested PIO autotuning) * remove config_it821x_chipset_for_pio() call from config_chipset_for_dma() as the driver sets ->autotune to 1 and ->tuneproc does the proper job now * convert the last user of config_it821x_chipset_for_pio() to use it821x_tuneproc(drive, 255) and remove no longer needed function While at it: * fix few comments * bump driver version Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-05pdc202xx_new: enable DMA for all ATAPI devicesBartlomiej Zolnierkiewicz
There is no reason to limit DMA to ide_cdrom type devices. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-05alim15x3: PIO fallback fixBartlomiej Zolnierkiewicz
If DMA tuning fails always set the best PIO mode. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-05aec62xx: fix PIO/DMA setup issuesSergei Shtylyov
Teach the driver's tuneproc() method to do PIO auto-runing properly since it treated 5 instead of 255 as auto-tune request, and also passed the mode limit of PIO5 to ide_get_best_pio_mode() despite supporting up to PIO4 only. While at it, also: - remove the driver's wrong claim about supporting SWDMA modes; - stop hooking ide_dma_timeout() method as the handler clearly doesn't fit for the task... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-05cmd64x: use interrupt status from MRDMODE register (take 2)Sergei Shtylyov
Fold the parts of the ide_dma_end() methods identical to __ide_dma_end() into a mere call to it. Start using faster versions of the ide_dma_end() and ide_dma_test_irq() methods for the PCI0646U and newer chips that have the duplicate interrupt status bits in the I/O mapped MRDMODE register, determing what methods to use at the driver load time. Do some cleanup/renaming in the "old" ide_dma_test_irq() method too. Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-05cmd64x: procfs code fixes/cleanups (take 2)Sergei Shtylyov
Fix several issues with the driver's procfs output: - when testing if channel is enabled, the code looks at the "simplex" bits, not at the real enable bits -- add #define for the primary channel enable bit; - UltraDMA modes 0, 1, 3 for slave drive reported incorrectly due to using the master drive's clock cycle resolution bit. While at it, also perform the following cleanups: - don't print extra newline before the first controller's dump; - correct the chipset names (from CMDxxx to PCI-xxx) - don't read from the registers which aren't used for dump; - better align the table column sizes; - rework UltraDMA mode dump code; - remove PIO mode dump code that has never been finished; - remove the duplicate interrupt status (the MRDMODE register bits mirror those those in the CFR and ARTTIM23 registers) and fold the dump into single line; - correct the style of the ?: operators... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-05cmd64x: add/fix enablebits (take 2)Sergei Shtylyov
The IDE core looks at the wrong bit when checking if the secondary channel is enabled on PCI0646 -- CNTRL register bit 7 is read-ahead disable, bit 3 is the correct one. Starting with PCI0646U chip, the primary channel can also be enabled/disabled -- so, add 'enablebits' initializers to each 'ide_pci_device_t' structure, handling the original PCI0646 via adding the init_setup() method and clearing the 'reg' field there if necessary... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-05cmd64x: interrupt status fixes (take 2)Sergei Shtylyov
The driver's ide_dma_test_irq() method was reading the MRDMODE register even on PCI0643/6 where it was write-only -- fix this by always reading the "backward- compatible" interrupt bits, renaming dma_alt_stat to irq_stat as the interrupt status bits are not coupled to DMA. In addition, wrong interrupt bit was tested/cleared for the primary channel -- it's bit 2 in all the chip specs and the driver used bit 1... :-/ Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-05cmd64x: fix multiword and remove single-word DMA supportSergei Shtylyov
Fix the multiword DMA and drop the single-word DMA support (which nobody will miss, I think). In order to do it, a number of changes was necessary: - rename program_drive_counts() to program_cycle_times(), pass to it cycle's total/active times instead of the clock counts, and convert them into the active/recovery clocks there instead of cmd64x_tune_pio() -- this causes quantize_timing() to also move; - contrarywise, move all the code handling the address setup timing into cmd64x_tune_pio(), so that setting MWDMA mode wouldn't change address setup; - remove from the speedproc() method the bogus code pretending to set the DMA timings by twiddling bits in the BMIDE status register, handle setting MWDMA by just calling program_cycle_times(); while at it, improve the style of that whole switch statement; - stop fiddling with the DMA capable bits in the speedproc() method -- they do not enable DMA, and are properly dealt with by the dma_host_{on,off} methods; - don't set hwif->swdma_mask in the init_hwif() method anymore. In addition to those changes, do the following: - in cmd64x_tune_pio(), when writing to ARTTIM23 register preserve the interrupt status bit, eliminate local_irq_{save|restore}() around this code as there's *no* actual race with the interrupt handler, and move cmdprintk() to a more fitting place -- after ide_get_best_pio_mode() call; - make {arttim|drwtim}_regs arrays single-dimensional, indexed with drive->dn; - rename {setup|recovery}_counts[] into more fitting {setup|recovery}_values[]; - in the speedproc() method, get rid of the duplicate reads/writes from/to the UDIDETCRx registers and of the extra variable used to store the transfer mode value after filtering, use another method of determining master/slave drive, and cleanup useless parens; - beautify cmdprintk() output here and there. While at it, remove meaningless comment about the driver being used only on UltraSPARC and long non-relevant RCS tag. :-) Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-05sl82c105: DMA support code cleanup (take 4)Sergei Shtylyov
Fold the now equivalent code in the ide_dma_check() method into a mere call to ide_use_dma(). Make config_for_dma() return non-zero if DMA mode has been set and call it from the ide_dma_check() method instead of ide_dma_on(). Defer writing the DMA timings to the chip registers until DMA is really turned on (and do not enable IORDY for DMA). Remove unneeded code from the init_hwif() method, improve its overall looks. Rename the dma_start(), ide_dma_check(), and ide_dma_lostirq() methods, and also use more proper hwif->dma_command, fix printk() and comment in the latter one as well. While at it, cleanup style in several places. Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-05sl82c105: rework PIO support (take 2)Sergei Shtylyov
Get rid of the 'pio_speed' member of 'ide_drive_t' that was only used by this driver by storing the PIO mode timings in the 'drive_data' instead -- this allows us to greatly simplify the process of "reloading" of the chip's timing register and do it right in sl82c150_dma_off_quietly() and to get rid of two extra arguments to config_for_pio() -- which got renamed to sl82c105_tune_pio() and now returns a PIO mode selected, with ide_config_drive_speed() call moved into the tuneproc() method, now called sl82c105_tune_drive() with the code to set drive's 'io_32bit' and 'unmask' flags in its turn moved to its proper place in the init_hwif() method. Also, while at it, rename get_timing_sl82c105() into get_pio_timings() and get rid of the code in it clamping cycle counts to 32 which was both incorrect and never executed anyway... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-05[TG3]: Eliminate the TG3_FLAG_5701_REG_WRITE_BUG flag.Matt Carlson
This patch removes the use of the TG3_FLAG_5701_REG_WRITE_BUG flag. It's logic is only used to set a function pointer and thus the logic can be collapsed and the flag removed. [ Comment tidy by Christoph Hellwig. -DaveM ] Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com>
2007-05-05[TG3]: Eliminate the TG3_FLAG_GOT_SERDES_FLOWCTL flag.Michael Chan
This flag does not do anything useful. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-05[TG3]: Remove reset during MAC address changes.Michael Chan
The reset was added a while back so that ASF could re-init whatever MAC address it wanted to use after the MAC address was changed. Instead of resetting, we can just keep MAC address 1 unchanged during MAC address changes if MAC address 1 is different from MAC address 0. This fixes 2 problems: 1. Bonding calls set_mac_address in contexts that cannot sleep. It no longer sleeps with the chip reset removed. 2. When ASF shares the same MAC address as the NIC, it needs to always do that even when the MAC address is changed. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-05[TG3]: WoL fixes.Gary Zambrano
Change TG3_FLAG_SERDES_WOL_CAP to TG3_FLAG_WOL_CAP to make it easier to manage WoL. This flag is now used consistently during ethtool WoL setup and power setting changes. Signed-off-by: Gary Zambrano <zambrano@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-05[TG3]: Clear GPIO mask before storing.Gary Zambrano
The GPIO settings may change during reset and so the stored values in tp->grc_local_ctrl should be cleared first. Signed-off-by: Gary Zambrano <zambrano@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-05[TG3]: Improve NVRAM sizing.Matt Carlson
This patch changes the NVRAM sizing procedure so that the driver can take advantage of devices with 1:1 NVRAM strapping configurations. This is useful in cases where the traditional NVRAM sizing method fails. In the event that the flash size cannot be determined, the largest known NVRAM size is used. The patch also removes support for 5755 NVRAM devices that are not supported by Broadcom and adds explicit sizing for this device. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>