aboutsummaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2007-10-30IB/ipath: Fix a race where s_last is updated without lock heldRalph Campbell
There is a small window where a send work queue entry could be overwritten by ib_post_send() because s_last is updated before the entry is read. This patch closes the window by acquiring the lock and updating the last send work queue entry index after reading the wr_id. Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-30IB/mlx4: Lock SQ lock in mlx4_ib_post_send()Roland Dreier
Because of a typo, mlx4_ib_post_send() takes the same lock rq.lock as mlx4_ib_post_recv(). Correct the code so the intended sq.lock is taken when posting a send. Noticed by Yossi Leybovitch and pointed out by Jack Morgenstein from Mellanox. Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-26IPoIB/cm: Fix receive QP cleanupRoland Dreier
Commit 1b524963 ("IPoIB/cm: Use common CQ for CM send completions") changed how the high-order bits of work request IDs were used, which had the effect that IPOIB_CM_RX_DRAIN_WRID was no longer handled as a connected mode receive completion. This leads to the messages ib1: cm send completion event with wrid 1073741823 (> 64) ib1: RX drain timing out when an interface with connected mode QPs is brought down. Fix this by making sure that both IPOIB_OP_CM and IPOIB_OP_RECV are set in IPOIB_CM_RX_DRAIN_WRID. Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-23Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: mlx4_core: Increase command timeout for INIT_HCA to 10 seconds IPoIB/cm: Use common CQ for CM send completions IB/uverbs: Fix checking of userspace object ownership IB/mlx4: Sanity check userspace send queue sizes IPoIB: Rewrite "if (!likely(...))" as "if (unlikely(!(...)))" IB/ehca: Enable large page MRs by default IB/ehca: Change meaning of hca_cap_mr_pgsize IB/ehca: Fix ehca_encode_hwpage_size() and alloc_fmr() IB/ehca: Fix masking error in {,re}reg_phys_mr() IB/ehca: Supply QP token for SRQ base QPs IPoIB: Use round_jiffies() for ah_reap_task RDMA/cma: Fix deadlock destroying listen requests RDMA/cma: Add locking around QP accesses IB/mthca: Avoid alignment traps when writing doorbells mlx4_core: Kill mlx4_write64_raw()
2007-10-23Merge git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-lguestLinus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-lguest: (45 commits) Use "struct boot_params" in example launcher Loading bzImage directly. Revert lguest magic and use hook in head.S Update lguest documentation to reflect the new virtual block device name. generalize lgread_u32/lgwrite_u32. Example launcher handle guests not being ready for input Update example launcher for virtio Lguest support for Virtio Remove old lguest I/O infrrasructure. Remove old lguest bus and drivers. Virtio helper routines for a descriptor ringbuffer implementation Module autoprobing support for virtio drivers. Virtio console driver Block driver using virtio. Net driver using virtio Virtio interface Boot with virtual == physical to get closer to native Linux. Allow guest to specify syscall vector to use. Rename "cr3" to "gpgdir" to avoid x86-specific naming. Pagetables to use normal kernel types ...
2007-10-23Merge git://git.infradead.org/mtd-2.6Linus Torvalds
* git://git.infradead.org/mtd-2.6: [MTD] [NOR] Fix deadlock in Intel chip driver caused by get_chip recursion [JFFS2] Fix return value from jffs2_write_end() [MTD] [OneNAND] Fix wrong free the static address in onenand_sim [MTD] [NAND] Replace -1 with -EBADMSG in nand error correction code [RSLIB] BUG() when passing illegal parameters to decode_rs8() or decode_rs16() [MTD] [NAND] treat any negative return value from correct() as an error [MTD] [NAND] nandsim: bugfix in initialization [MTD] Fix typo in Alauda config option help text. [MTD] [NAND] add s3c2440-specific read_buf/write_buf [MTD] [OneNAND] onenand-sim: fix kernel-doc and typos [JFFS2] Tidy up fix for ACL/permissions problem.
2007-10-23Merge branch 'sg' of git://git.kernel.dk/linux-2.6-blockLinus Torvalds
* 'sg' of git://git.kernel.dk/linux-2.6-block: sparc64: zero out dma_length fvr32: fixup dma-mapping for new sg layout sh/sh64: fixup dma-mapping for new sg layout Fix sctp compile m68knommu: remove sg_address() frv: update comment in scatterlist to reflect new setup blackfin: remove sg_address() arm: sg fallout mips: sg_page() fallout alpha: sg_virt() fallout intel-iommu: fix sg_page() parisc: fix sg_page() fallout ide: build fix net: fix xfrm build - missing scatterlist.h include [BLOCK] blk_rq_map_sg: force clear termination bit [BLOCK] Don't clear sg_dma_len/addr() in blk_rq_map_sg() s390 zfcp: sg fixups powerpc: Fix fallout from sg_page() changes IB/ehca: Fix sg_page() fallout arm: build fix
2007-10-23m68knommu: new style ColdFire UART driverGreg Ungerer
A new style serial driver for the Freescale ColdFire UART to replace the old style one currently in the tree (drivers/serial/mcfserial.c). Currently this UART is only found in the ColdFire CPU family of parts (thus I prefixed this patch [M68KNOMMU]). This has been around for a long while now, tested on all available platforms. Signed-off-by: Greg Ungerer <gerg@uclinux.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-23m68knommu: improve mii_do_cmd code in FEC driverPhilippe De Muyter
Improve the readability of mii_do_cmd(). Signed-off-by: Philippe De Muyter <phdm@macqel.be> Signed-off-by: Greg Ungerer <gerg@uclinux.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-23m68knommu: improve code formating FEC driverPhilippe De Muyter
Indent all the `else' the same way. Remove some unecesary white space. Signed-off-by: Philippe De Muyter <phdm@macqel.be> Signed-off-by: Greg Ungerer <gerg@uclinux.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-23Char: cyclades, fix potential NULL dereferenceJiri Slaby
ztxdone is jumped to even if tty is NULL and tty_wakeup placed after this label doesn't expect NULLed parameter, so this will cause an oops in some situations (why they scheduled a wakeup there before remove bottom half processing patch?). wakeup only in the case when we have non-null tty struct. Spotted by Adrian Bunk. Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Cc: Adrian Bunk <bunk@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-23md: raid5: fix clearing of biofill operationsDan Williams
ops_complete_biofill() runs outside of spin_lock(&sh->lock) and clears the 'pending' and 'ack' bits. Since the test_and_ack_op() macro only checks against 'complete' it can get an inconsistent snapshot of pending work. Move the clearing of these bits to handle_stripe5(), under the lock. Signed-off-by: Dan Williams <dan.j.williams@intel.com> Tested-by: Joel Bertrand <joel.bertrand@systella.fr> Signed-off-by: Neil Brown <neilb@suse.de> Cc: Stable <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-23md: fix an unsigned compare to allow creation of bitmaps with v1.0 metadataNeilBrown
As page->index is unsigned, this all becomes an unsigned comparison, which almost always returns an error. Signed-off-by: Neil Brown <neilb@suse.de> Cc: Stable <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-23[MTD] [NOR] Fix deadlock in Intel chip driver caused by get_chip recursionAlexey Korolev
This patch solves kernel deadlock issue seen on JFFF2 simultaneous operations. Detailed investigation of the issue showed that the kernel deadlock is caused by tons of recursive get_chip calls. Signed-off-by: Alexey Korolev <akorolev@infradead.org> Acked-by: Nicolas Pitre <nico@cam.org> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2007-10-23intel-iommu: fix sg_page()FUJITA Tomonori
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-23parisc: fix sg_page() falloutFUJITA Tomonori
arch/parisc/kernel/pci-dma.c: In function 'pa11_dma_map_sg': arch/parisc/kernel/pci-dma.c:487: error: 'struct scatterlist' has no member named 'page' arch/parisc/kernel/pci-dma.c: In function 'pa11_dma_unmap_sg': arch/parisc/kernel/pci-dma.c:508: error: 'struct scatterlist' has no member named 'page' arch/parisc/kernel/pci-dma.c:508: error: 'struct scatterlist' has no member named 'page' arch/parisc/kernel/pci-dma.c: In function 'pa11_dma_sync_sg_for_cpu': arch/parisc/kernel/pci-dma.c:535: error: 'struct scatterlist' has no member named 'page' arch/parisc/kernel/pci-dma.c:535: error: 'struct scatterlist' has no member named 'page' arch/parisc/kernel/pci-dma.c: In function 'pa11_dma_sync_sg_for_device': arch/parisc/kernel/pci-dma.c:545: error: 'struct scatterlist' has no member named 'page' arch/parisc/kernel/pci-dma.c:545: error: 'struct scatterlist' has no member named 'page' Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-23ide: build fixFUJITA Tomonori
git-drivers/ide/ide-probe.c: In function 'hwif_init': drivers/ide/ide-probe.c:1327: error: implicit declaration of function 'sg_init_table' Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-23s390 zfcp: sg fixupsJens Axboe
Based on initial patch from Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-23powerpc: Fix fallout from sg_page() changesOlof Johansson
Fix fallout from 18dabf473e15850c0dbc8ff13ac1e2806d542c15: In file included from include/linux/dma-mapping.h:52, from drivers/base/dma-mapping.c:10: include/asm/dma-mapping.h: In function 'dma_map_sg': include/asm/dma-mapping.h:288: error: 'struct scatterlist' has no member named 'page' include/asm/dma-mapping.h:288: error: 'struct scatterlist' has no member named 'page' include/asm/dma-mapping.h:288: error: 'struct scatterlist' has no member named 'page' include/asm/dma-mapping.h:289: error: 'struct scatterlist' has no member named 'page' include/asm/dma-mapping.h:290: error: 'struct scatterlist' has no member named 'page' include/asm/dma-mapping.h: In function 'dma_sync_sg_for_cpu': include/asm/dma-mapping.h:331: error: 'struct scatterlist' has no member named 'page' drivers/scsi/ps3rom.c: In function 'fetch_to_dev_buffer': drivers/scsi/ps3rom.c:150: error: 'struct scatterlist' has no member named 'page' Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-23IB/ehca: Fix sg_page() falloutOlof Johansson
More fallout from sg_page changes: drivers/infiniband/hw/ehca/ehca_mrmw.c: In function 'ehca_set_pagebuf_user1': drivers/infiniband/hw/ehca/ehca_mrmw.c:1779: error: 'struct scatterlist' has no member named 'page' drivers/infiniband/hw/ehca/ehca_mrmw.c: In function 'ehca_check_kpages_per_ate': drivers/infiniband/hw/ehca/ehca_mrmw.c:1835: error: 'struct scatterlist' has no member named 'page' drivers/infiniband/hw/ehca/ehca_mrmw.c: In function 'ehca_set_pagebuf_user2': drivers/infiniband/hw/ehca/ehca_mrmw.c:1870: error: 'struct scatterlist' has no member named 'page' Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-23generalize lgread_u32/lgwrite_u32.Rusty Russell
Jes complains that page table code still uses lgread_u32 even though it now uses general kernel pte types. The best thing to do is to generalize lgread_u32 and lgwrite_u32. This means we lose the efficiency of getuser(). We could potentially regain it if we used __copy_from_user instead of copy_from_user, but I'm not certain that our range check is equivalent to access_ok() on all platforms. Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Acked-by: Jes Sorensen <jes@sgi.com>
2007-10-23Lguest support for VirtioRusty Russell
This makes lguest able to use the virtio devices. We change the device descriptor page from a simple array to a variable length "type, config_len, status, config data..." format, and implement virtio_config_ops to read from that config data. We use the virtio ring implementation for an efficient Guest <-> Host virtqueue mechanism, and the new LHCALL_NOTIFY hypercall to kick the host when it changes. We also use LHCALL_NOTIFY on kernel addresses for very very early console output. We could have another hypercall, but this hack works quite well. Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
2007-10-23Remove old lguest I/O infrrasructure.Rusty Russell
This patch gets rid of the old lguest host I/O infrastructure and replaces it with a single hypercall "LHCALL_NOTIFY" which takes an address. The main change is the removal of io.c: that mainly did inter-guest I/O, which virtio doesn't yet support. Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
2007-10-23Remove old lguest bus and drivers.Rusty Russell
This gets rid of the lguest bus, drivers and DMA mechanism, to make way for a generic virtio mechanism. Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
2007-10-23Virtio helper routines for a descriptor ringbuffer implementationRusty Russell
These helper routines supply most of the virtqueue_ops for hypervisors which want to use a ring for virtio. Unlike the previous lguest implementation: 1) The rings are variable sized (2^n-1 elements). 2) They have an unfortunate limit of 65535 bytes per sg element. 3) The page numbers are always 64 bit (PAE anyone?) 4) They no longer place used[] on a separate page, just a separate cacheline. 5) We do a modulo on a variable. We could be tricky if we cared. 6) Interrupts and notifies are suppressed using flags within the rings. Users need only get the ring pages and provide a notify hook (KVM wants the guest to allocate the rings, lguest does it sanely). Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Cc: Dor Laor <dor.laor@qumranet.com>
2007-10-23Module autoprobing support for virtio drivers.Rusty Russell
This adds the logic to convert the virtio ids into module aliases, and includes a modalias entry in sysfs and the env var to make probing work. Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
2007-10-23Virtio console driverRusty Russell
This is an hvc-based virtio console driver. It's suboptimal becuase hvc expects to have raw access to interrupts and virtio doesn't assume that, so it currently polls. There are two solutions: expose hvc's "kick" interface, or wean off hvc. Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
2007-10-23Block driver using virtio.Rusty Russell
The block driver uses scatter-gather lists with sg[0] being the request information (struct virtio_blk_outhdr) with the type, sector and inbuf id. The next N sg entries are the bio itself, then the last sg is the status byte. Whether the N entries are in or out depends on whether it's a read or a write. We accept the normal (SCSI) ioctls: they get handed through to the other side which can then handle it or reply that it's unsupported. It's not clear that this actually works in general, since I don't know if blk_pc_request() requests have an accurate rq_data_dir(). Although we try to reply -ENOTTY on unsupported commands, ioctl(fd, CDROMEJECT) returns success to userspace. This needs a separate patch. Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Cc: Jens Axboe <jens.axboe@oracle.com>
2007-10-23Net driver using virtioRusty Russell
The network driver uses two virtqueues: one for input packets and one for output packets. This has nice locking properties (ie. we don't do any for recv vs send). TODO: 1) Big packets. 2) Multi-client devices (maybe separate driver?). 3) Resolve freeing of old xmit skbs (Christian Borntraeger) Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: netdev@vger.kernel.org
2007-10-23Virtio interfaceRusty Russell
This attempts to implement a "virtual I/O" layer which should allow common drivers to be efficiently used across most virtual I/O mechanisms. It will no-doubt need further enhancement. The virtio drivers add buffers to virtio queues; as the buffers are consumed the driver "interrupt" callbacks are invoked. There is also a generic implementation of config space which drivers can query to get setup information from the host. Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Cc: Dor Laor <dor.laor@qumranet.com> Cc: Arnd Bergmann <arnd@arndb.de>
2007-10-23Boot with virtual == physical to get closer to native Linux.Rusty Russell
1) This allows us to get alot closer to booting bzImages. 2) It means we don't have to know page_offset. 3) The Guest needs to modify the boot pagetables to create the PAGE_OFFSET mapping before jumping to C code. 4) guest_pa() walks the page tables rather than using page_offset. 5) We don't use page_offset to figure out whether to emulate: it was always kinda quesationable, and won't work for instructions done before remapping (bzImage unpacking in particular). 6) We still want the kernel address for tlb flushing: have the initial hypercall give us that, too. Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
2007-10-23Allow guest to specify syscall vector to use.Rusty Russell
(Based on Ron Minnich's LGUEST_PLAN9_SYSCALL patch). This patch allows Guests to specify what system call vector they want, and we try to reserve it. We only allow one non-Linux system call vector, to try to avoid DoS on the Host. Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
2007-10-23Rename "cr3" to "gpgdir" to avoid x86-specific naming.Rusty Russell
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
2007-10-23Pagetables to use normal kernel typesMatias Zabaljauregui
This is my first step in the migration of page_tables.c to the kernel types and functions/macros (2.6.23-rc3). Seems to be working OK. Signed-off-by: Matias Zabaljauregui <matias.zabaljauregui@cern.ch> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
2007-10-23Move register setup into i386_core.cJes Sorensen
Move setup_regs() to lguest_arch_setup_regs() in i386_core.c given that this is very architecture specific. Signed-off-by: Jes Sorensen <jes@sgi.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
2007-10-23Change example launcher to use unsigned long not u32Jes Sorensen
Apply Clue 2x4 to lguest userland<->kernel handling code and the lguest launcher. Pointers are not to be passed in u32's! Basic rule of thumb: Anything passing u32's back and forth should be passing unsigned longs to be portable to 64 bit archs. For those who forgotten already, I repeat: NO POINTERS IN u32! Signed-off-by: Jes Sorensen <jes@sgi.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
2007-10-23Make hypercalls arch-independent.Jes Sorensen
Clean up the hypercall code to make the code in hypercalls.c architecture independent. First process the common hypercalls and then call lguest_arch_do_hcall() if the call hasn't been handled. Rename struct hcall_ring to hcall_args. This patch requires the previous patch which reorganize the layout of struct lguest_regs on i386 so they match the layout of struct hcall_args. Signed-off-by: Jes Sorensen <jes@sgi.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
2007-10-23Introduce "hcall" pointer to indicate pending hypercall.Rusty Russell
Currently we look at the "trapnum" to see if the Guest wants a hypercall. But once the hypercall is done we have to reset trapnum to a bogus value, otherwise if we exit to userspace and return, we'd run the same hypercall twice (that was a nasty bug to find!). This has two main effects: 1) When Jes's patch changes the hypercall args to be a generic "struct hcall_args" we simply change the type of "lg->hcall". It's set by arch code, so if it has to copy args or something it can do so, and point "hcall" into lg->arch somewhere. 2) Async hypercalls only get run when an actual hypercall is pending. This simplfies the code a little and is a more logical semantic. Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
2007-10-23Reorder guest saved regs to match hyperall orderJes Sorensen
Move eax next to ebx/ecx/edx in struct lguest_regs on i386, so they will be located together and allow it to map directly to a struct hcall_ring entry (which will be renamed struct hcall_args as in a subsequent patch). This is in preparation for making the code hcall code architecture independent. Signed-off-by: Jes Sorensen <jes@sgi.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
2007-10-23Move i386 part of core.c to x86/core.c.Jes Sorensen
Separate i386 architecture specific from core.c and move it to x86/core.c and add x86/lguest.h header file to match. Signed-off-by: Jes Sorensen <jes@sgi.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
2007-10-23Make shadow IDT a complete IDT with 256 entries.Rusty Russell
This simplifies the code a little, in preparation for allowing alternate system call vectors in guests (Plan 9 uses 0x40). Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
2007-10-23Remove fixed limit on number of guests, and lguests array.Rusty Russell
Back when we had all the Guest state in the switcher, we had a fixed array of them. This is no longer necessary. If we switch the network code to using random_ether_addr (46 bits is enough to avoid clashes), we can get rid of the concept of "guest id" altogether. Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
2007-10-23Introduce guest mem offset, static link example launcherRusty Russell
In order to avoid problematic special linking of the Launcher, we give the Host an offset: this means we can use any memory region in the Launcher as Guest memory rather than insisting on mmap() at 0. The result is quite pleasing: a number of casts are replaced with simple additions. Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
2007-10-23Rename switcher.S to x86/switcher_32.SRusty Russell
lguest uses a "switcher" shim mapped high to bounce between host and guest. As lguest becomes less i386-centric, we separate this code into a subdir. Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
2007-10-23Move lguest guest support to arch/x86.Rusty Russell
Lguest has two sides: host support (to launch guests) and guest support (replacement boot path and paravirt_ops). This moves the guest side to arch/x86/lguest where it's closer to related code. Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Cc: Andi Kleen <ak@suse.de>
2007-10-23Clocksource is continuous regardless of the state of the host's TSC.Tony Breeds
Currently lguest will spend a lot of of time waking up the host, as it cannot go tickless (if the [host] TSC has been marked unstable). On my laptop I was getting ~40% of wakeups from lguest. With this patch applied, my laptop is much happier! Signed-off-by: Tony Breeds <tony@bakeyournoodle.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
2007-10-23lguest_devices belongs in lguest_bus.c: it's not i386-specific.Rusty Russell
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
2007-10-23Lguest currently depends on 32-bit x86, not just x86.Rusty Russell
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
2007-10-23Use copy_to_user() not put_user for struct timespecJes Sorensen
Use copy_to_user() when copying a struct timespec to the guest - put_user() cannot handle two long's in one go on a 64bit arch. Signed-off-by: Jes Sorensen <jes@sgi.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Cc: Jes Sorensen <jes@sgi.com> Cc: Al Viro <viro@ftp.linux.org.uk>
2007-10-23Remove binfmts.h include from lg.hRusty Russell
It wasn't needed since a very early prototype of lguest. Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-19 23:48:51 +0000