aboutsummaryrefslogtreecommitdiff
path: root/fs/ext4/group.h
AgeCommit message (Collapse)Author
2009-05-01ext4: Move fs/ext4/group.h into ext4.hTheodore Ts'o
Move the function prototypes in group.h into ext4.h so they are all defined in one place. Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
2008-07-11ext4: Rename read_block_bitmap() to ext4_read_block_bitmap()Theodore Ts'o
Since this a non-static function, make it be ext4 specific to avoid conflicts with potentially other filesystems. Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
2008-01-28ext4: add ext4_group_t, and change all group variables to this type.Avantika Mathur
In many places variables for block group are of type int, which limits the maximum number of block groups to 2^31. Each block group can have up to 2^15 blocks, with a 4K block size, and the max filesystem size is limited to 2^31 * (2^15 * 2^12) = 2^58 -- or 256 PB This patch introduces a new type ext4_group_t, of type unsigned long, to represent block group numbers in ext4. All occurrences of block group variables are converted to type ext4_group_t. Signed-off-by: Avantika Mathur <mathur@us.ibm.com>
2007-10-17Ext4: Uninitialized Block GroupsAndreas Dilger
In pass1 of e2fsck, every inode table in the fileystem is scanned and checked, regardless of whether it is in use. This is this the most time consuming part of the filesystem check. The unintialized block group feature can greatly reduce e2fsck time by eliminating checking of uninitialized inodes. With this feature, there is a a high water mark of used inodes for each block group. Block and inode bitmaps can be uninitialized on disk via a flag in the group descriptor to avoid reading or scanning them at e2fsck time. A checksum of each group descriptor is used to ensure that corruption in the group descriptor's bit flags does not cause incorrect operation. The feature is enabled through a mkfs option mke2fs /dev/ -O uninit_groups A patch adding support for uninitialized block groups to e2fsprogs tools has been posted to the linux-ext4 mailing list. The patches have been stress tested with fsstress and fsx. In performance tests testing e2fsck time, we have seen that e2fsck time on ext3 grows linearly with the total number of inodes in the filesytem. In ext4 with the uninitialized block groups feature, the e2fsck time is constant, based solely on the number of used inodes rather than the total inode count. Since typical ext4 filesystems only use 1-10% of their inodes, this feature can greatly reduce e2fsck time for users. With performance improvement of 2-20 times, depending on how full the filesystem is. The attached graph shows the major improvements in e2fsck times in filesystems with a large total inode count, but few inodes in use. In each group descriptor if we have EXT4_BG_INODE_UNINIT set in bg_flags: Inode table is not initialized/used in this group. So we can skip the consistency check during fsck. EXT4_BG_BLOCK_UNINIT set in bg_flags: No block in the group is used. So we can skip the block bitmap verification for this group. We also add two new fields to group descriptor as a part of uninitialized group patch. __le16 bg_itable_unused; /* Unused inodes count */ __le16 bg_checksum; /* crc16(sb_uuid+group+desc) */ bg_itable_unused: If we have EXT4_BG_INODE_UNINIT not set in bg_flags then bg_itable_unused will give the offset within the inode table till the inodes are used. This can be used by fsck to skip list of inodes that are marked unused. bg_checksum: Now that we depend on bg_flags and bg_itable_unused to determine the block and inode usage, we need to make sure group descriptor is not corrupt. We add checksum to group descriptor to detect corruption. If the descriptor is found to be corrupt, we mark all the blocks and inodes in the group used. Signed-off-by: Avantika Mathur <mathur@us.ibm.com> Signed-off-by: Andreas Dilger <adilger@clusterfs.com> Signed-off-by: Mingming Cao <cmm@us.ibm.com> Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>