| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Add the write verification buffer to the dataflash. The mtd_dataflash has
the CONFIG_DATAFLASH_WRITE_VERIFY so is better a change to Kconfig.
Signed-off-by: Michael Trimarchi <trimarchimichael@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Commit a7a6ace1406f95c3edb8365788f85984377f3832 revamped the OOB
handling but accidentally switched to 12-byte cleanmarkers, which is
incompatible with what 'flash_eraseall -j' will do. So using
flash_eraseall -j and then trying to mount the 'empty' flash will fail,
because the cleanmarkers aren't recognised.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
We've seen some evil corruption issues, where the corruption seems to be
introduced after the JFFS2 crc32 is calculated but before the NAND
controller calculates the ECC. So it's in RAM or in the PCI DMA
transfer; not on the flash. Attempt to catch it earlier by (optionally)
reading back from the flash immediately after writing it.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Convert many spaces to tabs; one or two other minor cosmetic fixes.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
After flushing the last page of an eraseblock, don't leave the
wbuf 'offset' field pointing at the start of the next physical
eraseblock. This was causing a BUG() on NOR-ECC (Sibley) flash, where
we start writing a little further in, after the cleanmarker.
Debugged by Alexander Belyakov <abelyako@googlemail.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:
drivers/mtd/Kconfig
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
This patch make JFFS2 able to work with UBI volumes via the emulated MTD
devices which are directly mapped to these volumes.
Signed-off-by: Artem Bityutskiy <dedekind@infradead.org>
|
|
In particular, remove the bit in the LICENCE file about contacting
Red Hat for alternative arrangements. Their errant IS department broke
that arrangement a long time ago -- the policy of collecting copyright
assignments from contributors came to an end when the plug was pulled on
the servers hosting the project, without notice or reason.
We do still dual-license it for use with eCos, with the GPL+exception
licence approved by the FSF as being GPL-compatible. It's just that nobody
has the right to license it differently.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
When compiling a LE-capable JFFS2 on PowerPC, wbuf.c fails to compile:
fs/jffs2/wbuf.c:973: error: braced-group within expression allowed only inside a function
fs/jffs2/wbuf.c:973: error: initializer element is not constant
fs/jffs2/wbuf.c:973: error: (near initialization for ‘oob_cleanmarker.magic’)
fs/jffs2/wbuf.c:974: error: braced-group within expression allowed only inside a function
fs/jffs2/wbuf.c:974: error: initializer element is not constant
fs/jffs2/wbuf.c:974: error: (near initialization for ‘oob_cleanmarker.nodetype’)
fs/jffs2/wbuf.c:975: error: braced-group within expression allowed only inside a function
fs/jffs2/wbuf.c:976: error: initializer element is not constant
fs/jffs2/wbuf.c:976: error: (near initialization for ‘oob_cleanmarker.totlen’)
Provide constant_cpu_to_je{16,32} functions, and use them for initialising the
offending structure.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
After a write error, any data in the write buffer must
be relocated. This is handled by the jffs2_wbuf_recover
function. This function does not fix up the erase block
summary information that is collected for writing at the
end of the block, which results in an incorrect summary
(or BUG if the summary was found to be empty).
As the summary is not essential (it is an optimisation),
it may be disabled for the current erase block when this
situation arises. This patch does that.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
New bad eraseblock is an event which is important enough to be printed
about.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
For the case when nand_write_page fail with -EIO for the first page in an
eraseblock, jffs2_wbuf_recover ends up producing a BUG in jffs2_block_refile
as jeb->first_node is not yet set up (it's set up later in jffs2_wbuf_recover).
This BUG is not really a bug; it's just jffs2_wbuf_recover calling
jffs2_block_refile with the wrong second parameter.
This patch takes care of this situation.
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
fs/jffs2/wbuf.c: In function 'jffs2_check_oob_empty':
fs/jffs2/wbuf.c:993: warning: format '%d' expects type 'int', but argument 3 has type 'size_t'
fs/jffs2/wbuf.c:993: warning: format '%d' expects type 'int', but argument 4 has type 'size_t'
fs/jffs2/wbuf.c: In function 'jffs2_check_nand_cleanmarker':
fs/jffs2/wbuf.c:1036: warning: format '%d' expects type 'int', but argument 3 has type 'size_t'
fs/jffs2/wbuf.c:1036: warning: format '%d' expects type 'int', but argument 4 has type 'size_t'
fs/jffs2/wbuf.c: In function 'jffs2_write_nand_cleanmarker':
fs/jffs2/wbuf.c:1062: warning: format '%d' expects type 'int', but argument 3 has type 'size_t'
fs/jffs2/wbuf.c:1062: warning: format '%d' expects type 'int', but argument 4 has type 'size_t'
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Nowadays MTD supports an MTD_OOB_AUTO option which allows users
to access free bytes in NAND's OOB as a contiguous buffer, although
it may be highly discontinuous.
This patch teaches JFFS2 to use this nice feature instead of the
old MTD_OOB_PLACE option. This for example caused problems with
OneNAND. Now JFFS2 does not care how are the free bytes situated.
This may change position of the clean marker on some flashes,
but this is not a problem. JFFS2 will just re-erase the empty
eraseblocks and write the new (correct) clean marker.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
As was discussed between Ricard Wanderlöf, David Woodhouse, Artem
Bityutskiy and me, the current API for reading/writing OOB is confusing.
The thing that introduces confusion is the need to specify ops.len
together with ops.ooblen for reads/writes that concern only OOB not data
area. So, ops.len is overloaded: when ops.datbuf != NULL it serves to
specify the length of the data read, and when ops.datbuf == NULL, it
serves to specify the full OOB read length.
The patch inlined below is the slightly updated version of the previous
patch serving the same purpose, but with the new Artem's comments taken
into account.
Artem, BTW, thanks a lot for your valuable input!
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
This patch converts the combination of list_del(A) and list_add(A, B) to
list_move(A, B) under fs/.
Cc: Ian Kent <raven@themaw.net>
Acked-by: Joel Becker <joel.becker@oracle.com>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Hans Reiser <reiserfs-dev@namesys.com>
Cc: Urban Widmark <urban@teststation.com>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Mark Fasheh <mark.fasheh@oracle.com>
Signed-off-by: Akinobu Mita <mita@miraclelinux.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Return -EUCLEAN on read when a bitflip was detected and corrected, so the
clients can react and eventually copy the affected block to a spare one.
Make all in kernel users aware of the change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Hopefully the last iteration on this!
The handling of out of band data on NAND was accompanied by tons of fruitless
discussions and halfarsed patches to make it work for a particular
problem. Sufficiently annoyed by I all those "I know it better" mails and the
resonable amount of discarded "it solves my problem" patches, I finally decided
to go for the big rework. After removing the _ecc variants of mtd read/write
functions the solution to satisfy the various requirements was to refactor the
read/write _oob functions in mtd.
The major change is that read/write_oob now takes a pointer to an operation
descriptor structure "struct mtd_oob_ops".instead of having a function with at
least seven arguments.
read/write_oob which should probably renamed to a more descriptive name, can do
the following tasks:
- read/write out of band data
- read/write data content and out of band data
- read/write raw data content and out of band data (ecc disabled)
struct mtd_oob_ops has a mode field, which determines the oob handling mode.
Aside of the MTD_OOB_RAW mode, which is intended to be especially for
diagnostic purposes and some internal functions e.g. bad block table creation,
the other two modes are for mtd clients:
MTD_OOB_PLACE puts/gets the given oob data exactly to/from the place which is
described by the ooboffs and ooblen fields of the mtd_oob_ops strcuture. It's
up to the caller to make sure that the byte positions are not used by the ECC
placement algorithms.
MTD_OOB_AUTO puts/gets the given oob data automaticaly to/from the places in
the out of band area which are described by the oobfree tuples in the ecclayout
data structre which is associated to the devicee.
The decision whether data plus oob or oob only handling is done depends on the
setting of the datbuf member of the data structure. When datbuf == NULL then
the internal read/write_oob functions are selected, otherwise the read/write
data routines are invoked.
Tested on a few platforms with all variants. Please be aware of possible
regressions for your particular device / application scenario
Disclaimer: Any whining will be ignored from those who just contributed "hot
air blurb" and never sat down to tackle the underlying problem of the mess in
the NAND driver grown over time and the big chunk of work to fix up the
existing users. The problem was not the holiness of the existing MTD
interfaces. The problems was the lack of time to go for the big overhaul. It's
easy to add more mess to the existing one, but it takes alot of effort to go
for a real solution.
Improvements and bugfixes are welcome!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The nand_oobinfo structure is not fitting the newer error correction
demands anymore. Replace it by struct nand_ecclayout and fixup the users
all over the place. Keep the nand_oobinfo based ioctl for user space
compability reasons.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The info structure for out of band data was copied into
the mtd structure. Make it a pointer and remove the ability
to set it from userspace. The position of ecc bytes is
defined by the hardware and should not be changed by software.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
A data node might not be in the fraglist; it could be f->metadata.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
This allows us to drop another pointer from the struct jffs2_raw_node_ref,
shrinking it to 8 bytes on 32-bit machines (if the TEST_TOTLEN) paranoia
check is turned off, which will be committed soon).
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Preallocation of refs is shortly going to be a per-eraseblock thing,
rather than per-filesystem. Add the required argument to the function.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
|
|
As the first step towards eliminating the ref->next_phys member and saving
memory by using an _array_ of struct jffs2_raw_node_ref per eraseblock,
stop the write functions from allocating their own refs; have them just
_reserve_ the appropriate number instead. Then jffs2_link_node_ref() can
just fill them in.
Use a linked list of pre-allocated refs in the superblock, for now. Once
we switch to an array, it'll just be a case of extending that array.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
MTD clients are agnostic of FLASH which needs ECC suppport.
Remove the functions and fixup the callers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The writev based write buffer implementation was far to complex as
in most use cases the write buffer had to be handled anyway.
Simplify the write buffer handling and use mtd->write instead.
From extensive testing no performance impact has been noted.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
We don't need the upper layers to deal with the physical offset. It's
_always_ c->nextblock->offset + c->sector_size - c->nextblock->free_size
so we might as well just let the actual write functions deal with that.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
In 2002, STMicro started producing NOR flashes with internal ECC protection
for small blocks (8 or 16 bytes). Support for those flashes was added by me.
In 2005, Intel Sibley flashes copied this strategy and Nico added support for
those. Merge the code for both.
Signed-off-by: Joern Engel <joern@wh.fh-wedel.de>
|
|
At least two flashes exists that have the concept of a minimum write unit,
similar to NAND pages, but no other NAND characteristics. Therefore, rename
the minimum write unit to "writesize" for all flashes, including NAND.
Signed-off-by: Joern Engel <joern@wh.fh-wedel.de>
|
|
Let's avoid the potential for forgetting to set ref->next_in_ino, by doing
it within jffs2_link_node_ref() instead.
This highlights the ugliness of what we're currently doing with
xattr_datum and xattr_ref structures -- we should find a nicer way of
dealing with that.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Next step in ongoing campaign to file a struct jffs2_raw_node_ref for every
piece of dirty space in the system, so that __totlen can be killed off....
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
If __totlen is going away, we need to pass the length in separately.
Also stop callers from needlessly setting ref->next_phys to NULL,
since that's done for them... and since that'll also be going away soon.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Some manual fixups for clashing kfree() cleanups etc.
|
|
This is the fs/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in fs/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
- assume wbuf may be of size which is not power of 2
- don't make strange assumption about not padding wbuf for DataFlash
- use wbuf = DataFlash page and eraseblock >= 8 Dataflash pages
From: Peter Menzebach <pm-mtd@mw-itcon.de>
Acked-by: Artem B. Bityutskiy <dedekind@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Simplify the debugging code further.
Update the TODO list
Signed-off-by: Artem B. Bityutskiy <dedekind@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The goal of summary is to speed up the mount time. Erase block summary (EBS)
stores summary information at the end of every (closed) erase block. It is
no longer necessary to scan all nodes separetly (and read all pages of them)
just read this "small" summary, where every information is stored which is
needed at mount time.
This summary information is stored in a JFFS2_FEATURE_RWCOMPAT_DELETE. During
the mount process if there is no summary info the orignal scan process will
be executed. EBS works with NAND and NOR flashes, too.
There is a user space tool called sumtool to generate this summary
information for a JFFS2 image.
Signed-off-by: Ferenc Havasi <havasi@inf.u-szeged.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Intels Sibley flash needs JFFS2 write buffer functionality
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Various simplifiactions. printk format corrections.
Convert more code to use the new debug functions.
Signed-off-by: Artem B. Bityutskiy <dedekind@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
If debugging is disabled, define debugging functions as empty macros, instead
of using Dx() explicitly.
Signed-off-by: Artem B. Bityutskiy <dedekind@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Move debug functions into a seperate source file
Signed-off-by: Artem B. Bityutskiy <dedekind@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
I recently picked up my older work to remove unnecessary #includes of
sched.h, starting from a patch by Dave Jones to not include sched.h
from module.h. This reduces the number of indirect includes of sched.h
by ~300. Another ~400 pointless direct includes can be removed after
this disentangling (patch to follow later).
However, quite a few indirect includes need to be fixed up for this.
In order to feed the patches through -mm with as little disturbance as
possible, I've split out the fixes I accumulated up to now (complete for
i386 and x86_64, more archs to follow later) and post them before the real
patch. This way this large part of the patch is kept simple with only
adding #includes, and all hunks are independent of each other. So if any
hunk rejects or gets in the way of other patches, just drop it. My scripts
will pick it up again in the next round.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Artem B. Bityuckiy <dedekind@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
