| Age | Commit message (Collapse) | Author |
|---|
|
arch/arm/plat-iop/io.c:26: error: conflicting types for '__iop3xx_ioremap'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
'ns9xxx', 'omap', 'pxa', 'rpc', 's3c' and 'sa1100' into devel
|
|
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Currently the iop3xx platform support code assumes that RedBoot is the
bootloader and has already initialized the ATU. Linux should handle this
initialization for three reasons:
1/ The memory map that RedBoot sets up is not optimal (page_to_dma and
virt_to_phys return different addresses). The effect of this is that using
the dma mapping API for the internal bus dma units generates pci bus
addresses that are incorrect for the internal bus.
2/ Not all iop platforms use RedBoot
3/ If the ATU is already initialized it indicates that the iop is an add-in
card in another host, it does not own the PCI bus, and should not be
re-initialized.
Changelog:
* rather than change nr_controllers to zero, simply do not call
pci_common_init
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
* architecture specific details are handled in asm/arch/time.h
* ARCH_IOP13XX now selects PLAT_IOP
* as suggested by Lennert use ifdef CONFIG_XSCALE to skip the cp_wait on
XSC3
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
get_irqnr_preamble allows machines to take some action before entering the
get_irqnr_and_base loop. On iop we enable cp6 access.
arch_ret_to_user is added to the userspace return path to allow individual
architectures to take actions, like disabling coprocessor access, before
the final return to userspace.
Per Nicolas Pitre's note, there is no need to cp_wait on the return to user
as the latency to return is sufficient.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Implement a custom ioremap implementation for iop3xx. This saves
establishing new mappings. It also cleans up the PCI IO resource to be a
physical address rather than a virtual address as Russell pointed out on
the original iop13xx port.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Since the iop32x code isn't iop321-specific, and the iop33x code isn't
iop331-specfic, do a s/iop321/iop32x/ and s/iop331/iop33x/, and tidy up
the code to conform to the coding style guidelines somewhat better.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Factor out the register defines for a number of other peripherals
common to the iop32x and iop33x.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Revamp the iop3xx board support: move the support code for each iop
board type into its own file, start using platform serial and platform
physmap flash devices, switch to a per-board time tick rate, and get
rid of the ARCH_EP80219 and STEPD config options by doing the relevant
checks at run time.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Squeeze three instructions out of the iop32x irq demuxer, and nine
out of the iop33x irq demuxer by using the hardware vector generator.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Implement the gpio_line_{config,get,set} API for iop3xx.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Get rid of the unused IOP3??_IRQ_OFS irq offset define, start IRQ
numbering from zero.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add CP6 enable/disable sequences to the timekeeping code and the IRQ
code. As a result, we can't depend on CP6 access being enabled when
we enter get_irqnr_and_base anymore, so switch the latter over to
using memory-mapped accesses for now.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Switch the iop32x and iop33x code over to the common time implementation,
and remove the (nearly identical) iop32x and iop33x time implementations.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Merge and rewrite the iop32x/iop33x time code to do lost jiffy
tracking properly, and put the result in plat-iop/time.c.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Switch the iop32x and iop33x code over to the common PCI implementation,
and remove the (nearly identical) iop32x and iop33x PCI implementations.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Move the i2c bits shared between iop32x and iop33x to plat-iop/i2c.c
and include/asm-arm/hardware/iop3xx.h.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Introduce the arch/arm/plat-iop directory, for code shared between the
iop32x and iop33x, and move the common memory map setup bits there.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Split the iop3xx mach type into iop32x and iop33x -- split the config
symbols, and move the code in the mach-iop3xx directory to the mach-iop32x
and mach-iop33x directories.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
