aboutsummaryrefslogtreecommitdiff
path: root/include/asm-sparc64/cpudata.h
AgeCommit message (Collapse)Author
2006-03-22[SPARC64]: Add a secondary TSB for hugepage mappings.David S. Miller
Signed-off-by: David S. Miller <davem@davemloft.net>
2006-03-20[SPARC64]: Kill cpudata->idle_volume.David S. Miller
Set, but never used. We used to use this for dynamic IRQ retargetting, but that code died a long time ago. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-03-20[SPARC64]: Fix uniprocessor IRQ targetting on SUN4V.David S. Miller
We need to use the real hardware processor ID when targetting interrupts, not the "define to 0" thing the uniprocessor build gives us. Also, fill in the Node-ID and Agent-ID fields properly on sun4u/Safari. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-03-20[SPARC64]: Get SUN4V SMP working.David S. Miller
The sibling cpu bringup is extremely fragile. We can only perform the most basic calls until we take over the trap table from the firmware/hypervisor on the new cpu. This means no accesses to %g4, %g5, %g6 since those can't be TLB translated without our trap handlers. In order to achieve this: 1) Change sun4v_init_mondo_queues() so that it can operate in several modes. It can allocate the queues, or install them in the current processor, or both. The boot cpu does both in it's call early on. Later, the boot cpu allocates the sibling cpu queue, starts the sibling cpu, then the sibling cpu loads them in. 2) init_cur_cpu_trap() is changed to take the current_thread_info() as an argument instead of reading %g6 directly on the current cpu. 3) Create a trampoline stack for the sibling cpus. We do our basic kernel calls using this stack, which is locked into the kernel image, then go to our proper thread stack after taking over the trap table. 4) While we are in this delicate startup state, we put 0xdeadbeef into %g4/%g5/%g6 in order to catch accidental accesses. 5) On the final prom_set_trap_table*() call, we put &init_thread_union into %g6. This is a hack to make prom_world(0) work. All that wants to do is restore the %asi register using get_thread_current_ds(). Longer term we should just do the OBP calls to set the trap table by hand just like we do for everything else. This would avoid that silly prom_world(0) issue, then we can remove the init_thread_union hack. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-03-20[SPARC64]: Use ASI_SCRATCHPAD address 0x0 properly.David S. Miller
This is where the virtual address of the fault status area belongs. To set it up we don't make a hypervisor call, instead we call OBP's SUNW,set-trap-table with the real address of the fault status area as the second argument. And right before that call we write the virtual address into ASI_SCRATCHPAD vaddr 0x0. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-03-20[SPARC64]: Sun4v cross-call sending support.David S. Miller
Technically the hypervisor call supports sending in a list of all cpus to get the cross-call, but I only pass in one cpu at a time for now. The multi-cpu support is there, just ifdef'd out so it's easy to enable or delete it later. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-03-20[SPARC64]: Sun4v interrupt handling.David S. Miller
Sun4v has 4 interrupt queues: cpu, device, resumable errors, and non-resumable errors. A set of head/tail offset pointers help maintain a work queue in physical memory. The entries are 64-bytes in size. Each queue is allocated then registered with the hypervisor as we bring cpus up. The two error queues each get a kernel side buffer that we use to quickly empty the main interrupt queue before we call up to C code to log the event and possibly take evasive action. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-03-20[SPARC64]: Add sun4v mondo queue bases to struct trap_per_cpu.David S. Miller
Also, correct TRAP_PER_CPU_FAULT_INFO define, it should be 0x40 not 0x20. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-03-20[SPARC64]: asm/cpudata.h needs asm/asi.hDavid S. Miller
For the expansion of __GET_CPUID() on SMP. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-03-20[SPARC64]: Rename gl_{1,2}insn_patch --> sun4v_{1,2}insn_patchDavid S. Miller
Signed-off-by: David S. Miller <davem@davemloft.net>
2006-03-20[SPARC64]: Initial sun4v TLB miss handling infrastructure.David S. Miller
Things are a little tricky because, unlike sun4u, we have to: 1) do a hypervisor trap to do the TLB load. 2) do the TSB lookup calculations by hand Signed-off-by: David S. Miller <davem@davemloft.net>
2006-03-20[SPARC64]: Sanitize %pstate writes for sun4v.David S. Miller
If we're just switching between different alternate global sets, nop it out on sun4v. Also, get rid of all of the alternate global save/restore in the OBP CIF trampoline code. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-03-20[SPARC64]: Add initial code to twiddle %gl on trap entry/exit.David S. Miller
Instead of setting/clearing PSTATE_AG we have to change the %gl register value on sun4v. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-03-20[SPARC64]: Add sun4v case to __GET_CPUID() patch tables.David S. Miller
Signed-off-by: David S. Miller <davem@davemloft.net>
2006-03-20[SPARC64]: Add explicit register args to trap state loading macros.David S. Miller
This, as well as making the code cleaner, allows a simplification in the TSB miss handling path. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-03-20[SPARC64]: Refine code sequences to get the cpu id.David S. Miller
On uniprocessor, it's always zero for optimize that. On SMP, the jmpl to the stub kills the return address stack in the cpu branch prediction logic, so expand the code sequence inline and use a code patching section to fix things up. This also always better and explicit register selection, which will be taken advantage of in a future changeset. The hard_smp_processor_id() function is big, so do not inline it. Fix up tests for Jalapeno to also test for Serrano chips too. These tests want "jbus Ultra-IIIi" cases to match, so that is what we should test for. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-03-20[SPARC64]: Fix race in LOAD_PER_CPU_BASE()David S. Miller
Since we use %g5 itself as a temporary, it can get clobbered if we take an interrupt mid-stream and thus cause end up with the final %g5 value too early as a result of rtrap processing. Set %g5 at the very end, atomically, to avoid this problem. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-03-20[SPARC64]: Kill sole argument passed to setup_tba().David S. Miller
No longer used, and move extern declaration to a header file. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-03-20[SPARC64]: Elminate all usage of hard-coded trap globals.David S. Miller
UltraSPARC has special sets of global registers which are switched to for certain trap types. There is one set for MMU related traps, one set of Interrupt Vector processing, and another set (called the Alternate globals) for all other trap types. For what seems like forever we've hard coded the values in some of these trap registers. Some examples include: 1) Interrupt Vector global %g6 holds current processors interrupt work struct where received interrupts are managed for IRQ handler dispatch. 2) MMU global %g7 holds the base of the page tables of the currently active address space. 3) Alternate global %g6 held the current_thread_info() value. Such hardcoding has resulted in some serious issues in many areas. There are some code sequences where having another register available would help clean up the implementation. Taking traps such as cross-calls from the OBP firmware requires some trick code sequences wherein we have to save away and restore all of the special sets of global registers when we enter/exit OBP. We were also using the IMMU TSB register on SMP to hold the per-cpu area base address, which doesn't work any longer now that we actually use the TSB facility of the cpu. The implementation is pretty straight forward. One tricky bit is getting the current processor ID as that is different on different cpu variants. We use a stub with a fancy calling convention which we patch at boot time. The calling convention is that the stub is branched to and the (PC - 4) to return to is in register %g1. The cpu number is left in %g6. This stub can be invoked by using the __GET_CPUID macro. We use an array of per-cpu trap state to store the current thread and physical address of the current address space's page tables. The TRAP_LOAD_THREAD_REG loads %g6 with the current thread from this table, it uses __GET_CPUID and also clobbers %g1. TRAP_LOAD_IRQ_WORK is used by the interrupt vector processing to load the current processor's IRQ software state into %g6. It also uses __GET_CPUID and clobbers %g1. Finally, TRAP_LOAD_PGD_PHYS loads the physical address base of the current address space's page tables into %g7, it clobbers %g1 and uses __GET_CPUID. Many refinements are possible, as well as some tuning, with this stuff in place. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-03-20[SPARC64]: Kill pgtable quicklists and use SLAB.David S. Miller
Taking a nod from the powerpc port. With the per-cpu caching of both the page allocator and SLAB, the pgtable quicklist scheme becomes relatively silly and primitive. Signed-off-by: David S. Miller <davem@davemloft.net>
2006-03-20[SPARC64]: No need to D-cache color page tables any longer.David S. Miller
Unlike the virtual page tables, the new TSB scheme does not require this ugly hack. Signed-off-by: David S. Miller <davem@davemloft.net>
2005-09-26[SPARC64]: Probe D/I/E-cache config and use.David S. Miller
At boot time, determine the D-cache, I-cache and E-cache size and line-size. Use them in cache flushes when appropriate. This change was motivated by discovering that the D-cache on UltraSparc-IIIi and later are 64K not 32K, and the flushes done by the Cheetah error handlers were assuming a 32K size. There are still some pieces of code that are hard coding things and will need to be fixed up at some point. While we're here, fix the D-cache and I-cache parity error handlers to run with interrupts disabled, and when the trap occurs at trap level > 1 log the event via a counter displayed in /proc/cpuinfo. Signed-off-by: David S. Miller <davem@davemloft.net>
2005-08-29[SPARC64]: Eliminate irq_cpustat_t.David S. Miller
We can put the __softirq_pending mask in the cpudata, no need for the silly NR_CPUS array in kernel/softirq.c Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-16Linux-2.6.12-rc2Linus Torvalds
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!