aboutsummaryrefslogtreecommitdiff
path: root/include/linux/libata.h
AgeCommit message (Collapse)Author
2007-10-29[libata] Link power management infrastructureKristen Carlson Accardi
Device Initiated Power Management, which is defined in SATA 2.5 can be enabled for disks which support it. This patch enables DIPM when the user sets the link power management policy to "min_power". Additionally, libata drivers can define a function (enable_pm) that will perform hardware specific actions to enable whatever power management policy the user set up for Host Initiated Power management (HIPM). This power management policy will be activated after all disks have been enumerated and intialized. Drivers should also define disable_pm, which will turn off link power management, but not change link power management policy. Documentation/scsi/link_power_management_policy.txt has additional information. Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2007-10-29libata: implement ata_wait_after_reset()Tejun Heo
On certain device/controller combination, 0xff status is asserted after reset and doesn't get cleared during 150ms post-reset wait. As 0xff status is interpreted as no device (for good reasons), this can lead to misdetection on such cases. This patch implements ata_wait_after_reset() which replaces the 150ms sleep and waits upto ATA_TMOUT_FF_WAIT if status is 0xff. ATA_TMOUT_FF_WAIT is currently 800ms which is enough for HHD424020F7SV00 to get detected but not enough for Quantum GoVault drive which is known to take upto 2s. Without parallel probing, spending 2s on 0xff port would incur too much delay on ata_piix's which use 0xff to indicate empty port and doesn't have SCR register, so GoVault needs to wait till parallel probing. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-29libata: track SLEEP state and issue SRST to wake it upTejun Heo
ATA devices in SLEEP mode don't respond to any commands. SRST is necessary to wake it up. Till now, when a command is issued to a device in SLEEP mode, the command times out, which makes EH reset the device and retry the command after that, causing a long delay. This patch makes libata track SLEEP state and issue SRST automatically if a command is about to be issued to a device in SLEEP. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Bruce Allen <ballen@gravity.phys.uwm.edu> Cc: Andrew Paprocki <andrew@ishiboo.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-23[libata] checkpatch-inspired cleanupsJeff Garzik
Tackle the relatively sane complaints of checkpatch --file. The vast majority is indentation and whitespace changes, the rest are * #include fixes * printk KERN_xxx prefix addition * BSS/initializer cleanups Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2007-10-18[libata] kill ata_sg_is_last()Jeff Garzik
Short term, this works around a bug introduced by early sg-chaining work. Long term, removing this function eliminates a branch from a hot path loop in each scatter/gather table build. Also, as this code demonstrates, we don't need to _track_ the end of the s/g list, as long as we mark it in some way. And doing so programatically is nice. So its a useful cleanup, regardless of its short term effects. Based conceptually on a quick patch by Jens Axboe. Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2007-10-16libata: convert to using sg helpersJens Axboe
This converts libata to using the sg helpers for looking up sg elements, instead of doing it manually. Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-12[libata] struct pci_dev related cleanupsJeff Garzik
* remove pointless pci_dev_to_dev() wrapper. Just directly reference the embedded struct device like everyone else does. * pata_cs5520: delete cs5520_remove_one(), it was a duplicate of ata_pci_remove_one() * linux/libata.h: don't bother including linux/pci.h, we don't need it. Simply declare 'struct pci_dev' and assume interested parties will include the header, as they should be doing anyway. * linux/libata.h: consolidate all CONFIG_PCI declarations into a single location in the header. Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2007-10-12libata: use ata_exec_internal() for PMP register accessTejun Heo
PMP registers used to be accessed with dedicated accessors ->pmp_read and ->pmp_write. During reset, those callbacks are called with the port frozen so they should be able to run without depending on interrupt delivery. To achieve this, they were implemented polling. However, as resetting the host port makes the PMP to isolate fan-out ports until SError.X is cleared, resetting fan-out ports while port is frozen doesn't buy much additional safety. This patch updates libata PMP support such that PMP registers are accessed using regular ata_exec_internal() mechanism and kills ->pmp_read/write() callbacks. The following changes are made. * PMP access helpers - sata_pmp_read_init_tf(), sata_pmp_read_val(), sata_pmp_write_init_tf() are folded into sata_pmp_read/write() which are now standalone PMP register access functions. * sata_pmp_read/write() returns err_mask instead of rc. This is consistent with other functions which issue internal commands and allows more detailed error reporting. * ahci interrupt handler is modified to ignore BAD_PMP and spurious/illegal completion IRQs while reset is in progress. These conditions are expected during reset. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12libata: implement ATA_PFLAG_RESETTINGTejun Heo
Implement ATA_PFLAG_RESETTING. This flag is set while reset is in progress. It's set before prereset is called and cleared after reset fails or postreset is finished. This flag itself doesn't have any function. It will be used by LLDs to tell whether reset is in progress if it needs to behave differently during reset. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12libata-core: Expose gtm methods for driver useAlan Cox
Talk to the dark side our driver has to, yes. Much misleading is the data. Store it in a structure we do so that it may be parsed. Signed-off-by: Alan Cox <alan@redhat.com> -- Whats small, old and shouts phrases out of order across mountains ? Yodla.. Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12libata: Add a drivers/ide style DMA disableAlan Cox
This is useful when debugging, handling problem systems, or for distributions just to get the system installed so it can be sorted out later. This is a bit smarter than the old IDE one and lets you do libata.dma=0 Disable all PATA DMA like old IDE libata.dma=1 Disk DMA only libata.dma=2 ATAPI DMA only libata.dma=4 CF DMA only (or combinations thereof - 0,1,3 being the useful ones I suspect) (I've split CF as it seems to be a seperate case of pain and suffering different to the others and caused by assorted PIO wired adapters etc) Signed-off-by: Alan Cox <alan@redhat.com> [edited to work on SATA too, changing name from 'pata_dma' to 'dma'] Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2007-10-12libata-pmp: implement qc_defer for command switching PMP supportTejun Heo
Implement sata_pmp_qc_defer_cmd_switch() - standard qc_defer for command switching PMP support. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12libata-pmp: implement Port Multiplier supportTejun Heo
Implement Port Multiplier support. To support PMP, a LLDD has to supply ops->pmp_read() and pmp_write(). If non-null, ->pmp_attach and ->pmp_detach are called on PMP attach and detach, respectively. ->pmp_read/write() can be called while the port is frozen, so they must be implemented by polling. This patch supplies several helpers to ease ->pmp_read/write() implementation. Also, irq_handler and error_handler must be PMP aware. Most of PMP aware EH can be done by calling ata_pmp_do_eh() with appropriate methods. PMP EH uses separate set of reset methods and this patch implements standard prereset, hardreset and postreset methods. This patch only implements PMP support. The next patch will integrate PMP into the reset of libata and thus enable PMP support. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12[PATCH] libata: Fix HPA handling regressionAlan Cox
Restore the support for handling drives that report one sector too many (ie SCSI not ATA style). This worked before the HPA update but was removed in that process. Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12libata-pmp-prep: implement sata_async_notification()Tejun Heo
AN serves multiple purposes. For ATAPI, it's used for media change notification. For PMP, for downstream PHY status change notification. Implement sata_async_notification() which demultiplexes AN. To avoid unnecessary port events, ATAPI AN is not enabled if PMP is attached but SNTF is not available. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Kriten Carlson Accardi <kristen.c.accardi@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12libata-pmp-prep: implement ATA_HORKAGE_SKIP_PMTejun Heo
Some pseudo devices fail PM commands unnecessarily aborting system suspend. Implement ATA_HORKAGE_SKIP_PM which makes libata skip PM commands for these devices. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12libata-pmp-prep: implement ATA_LFLAG_DISABLEDTejun Heo
Implement ATA_LFLAG_DISABLED. The flag indicates the link is disabled due to EH recovery failure. While a link is disabled, no EH action is taken on the link and suspend/resume become noop too. This will be used by PMP links to manage failed links. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12libata-pmp-prep: implement ATA_LFLAG_NO_RETRYTejun Heo
Some PMP links are connected to internal pseudo devices which may come and go depending on situation. There's no reason to try hard to recover them. ATA_LFLAG_NO_RETRY tells EH to not retry if the device attached to the link fails. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12libata-pmp-prep: implement ATA_LFLAG_NO_SRST, ASSUME_ATA and ASSUME_SEMBTejun Heo
Some links on some PMPs locks up on SRST and/or report incorrect device signature. Implement ATA_LFLAG_NO_SRST, ASSUME_ATA and ASSUME_SEMB to handle these quirky links. NO_SRST makes EH avoid SRST. ASSUME_ATA and SEMB forces class code to ATA and SEMB_UNSUP respectively. Note that SEMB isn't currently supported yet so the _UNSUP variant is used. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12libata-pmp-prep: implement qc_defer helpersTejun Heo
Implement ap->nr_active_links (the number of links with active qcs), ap->excl_link (pointer to link which can be used by ->qc_defer and is cleared when a qc with ATA_QCFLAG_CLEAR_EXCL completes), and ata_link_active(). These can be used by ->qc_defer() to implement proper command exclusion. This set of helpers seem enough for both sil24 (ATAPI exclusion needed) and cmd-switching PMP. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12libata-pmp-prep: implement ops->qc_defer()Tejun Heo
Controllers which support PMP have various restrictions on which combinations of commands are allowed to what number of devices concurrently. This patch implements ops->qc_defer() which determines whether a qc can be issued at the moment or should be deferred. If the function returns ATA_DEFER_LINK, the qc will be deferred until a qc completes on the link. If ATA_DEFER_PORT, until a qc completes on any link. The defer conditions are advisory and in general ATA_DEFER_LINK can be considered as lower priority deferring than ATA_DEFER_PORT. ops->qc_defer() replaces fixed ata_scmd_need_defer(). For standard NCQ/non-NCQ exclusion, ata_std_qc_defer() is implemented. ahci and sata_sil24 are converted to use ata_std_qc_defer(). ops->qc_defer() is heavier than the original mechanism because full qc is prepped before determining to defer it, but various information is needed to determine defer conditinos and fully translating a qc is the only way to supply such information in generic manner. IMHO, this shouldn't cause any noticeable performance issues as * for most cases deferring occurs rarely (except for NCQ-aware cmd-switching PMP) * translation itself isn't that expensive * once deferred the command won't be repeated until another command completes which usually is a very long time cpu-wise. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12libata-pmp-prep: add PMP related constants, fields, ops and update helpersTejun Heo
Add PMP related constants, fields and ops. Also, update ata_class_enabled/disabled() such that PMP classes are considered. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12libata: update ata_dev_try_classify() argumentsTejun Heo
Make ata_dev_try_classify() take a pointer to ata_device instead of ata_port/port_number combination for consistency and add @present argument. @present indicates whether the device seems present during reset. It's the result of TF access during softreset and link onlineness during hardreset. @present will be used to improve diagnostic failure handling. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12ata: increase allowed config flagsKristen Carlson Accardi
In anticipation of more features, increase number of config flags allowed, and move the init flags. Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com> Cc: Hugh Dickens <hugh@veritas.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12libata: move EH repeat reporting into ata_eh_report()Tejun Heo
EH is sometimes repeated without any error or action. For example, this happens when probing IDENTIFY fails because of a phantom device. In these cases, all the repeated EH does is making sure there is no unhandled error or pending action and return. This repeation is necessary to avoid losing any event which occurred while EH was in progress. Unfortunately, this dry run causes annonying "EH pending after completion" message. This patch moves the repeat reporting into ata_eh_report() such that it's more compact and skipped on dry runs. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Mikael Pettersson <mikep@it.uu.se> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12libata: implement and use ata_port_desc() to report port configurationTejun Heo
Currently, port configuration reporting has the following problems. * iomapped address is reported instead of raw address * report contains irrelevant fields or lacks necessary fields for non-SFF controllers. * host->irq/irq2 are there just for reporting and hacky. This patch implements and uses ata_port_desc() and ata_port_pbar_desc(). ata_port_desc() is almost identical to ata_ehi_push_desc() except that it takes @ap instead of @ehi, has no locking requirement, can only be used during host initialization and " " is used as separator instead of ", ". ata_port_pbar_desc() is a helper to ease reporting of a PCI BAR or an offsetted address into it. LLD pushes whatever description it wants using the above two functions. The accumulated description is printed on host registration after "[S/P]ATA max MAX_XFERMODE ". SFF init helpers and ata_host_activate() automatically add descriptions for addresses and irq respectively, so only LLDs which isn't standard SFF need to add custom descriptions. In many cases, such controllers need to report different things anyway. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12[libata] Remove ->port_disable() hookJeff Garzik
It was always set to ata_port_disable(). Removed the hook, and replaced the very few ap->ops->port_disable() callsites with direct calls to ata_port_disable(). Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12[libata] add ACPI cable detect APIAlan Cox
Combined from two Alan Cox patches: 1) libata: ACPI checks for 80wire cable We can use the ACPI mode information with several drivers as a hint to cable type. If the ACPI mode set by the BIOS is faster than UDMA33 then we know the BIOS thinks there are 80wire cables. If it doesn't set such a mode or it has no ACPI method then we get no further information and can rely on existing approaches Introduce the function headers needed. Null it out for non ACPI boxes Signed-off-by: Alan Cox <alan@redhat.com> 2) libata: ACPI checks for 80wire cable Provide actual methods for checking if the ACPI support thinks the cable is 80wire, or doesn't know Signed-off-by: Alan Cox <alan@redhat.com> Combined into a single changeset and Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12[libata] Remove ->irq_ack() hook, and ata_dummy_irq_on()Jeff Garzik
* ->irq_ack() is redundant to what the irq handler already performs... chk-status + irq-clear. Furthermore, it is only called in one place, when screaming-irq-debugging is enabled, so we don't want to bother with a hook just for that. * ata_dummy_irq_on() is only ever used in drivers that have no callpath reaching ->irq_on(). Remove .irq_on hook from those drivers, and the now-unused ata_dummy_irq_on() Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12libata: add printf format attribute to ehi desc functionsTejun Heo
Tell the compiler that [__]ata_ehi_push_desc() functions take printf style format string and arguments. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12libata: use ata_port_printk() in ata_wait_idle()Tejun Heo
ata_wait_idle() identified controller by printing out the address of the Status register. This is bogus because 1. it's iomapped address 2. some controllers don't have Status register and don't initialize the field. Use ata_port_printk() instead. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12[libata] ahci: send event when AN receivedKristen Carlson Accardi
When we get an SDB FIS with the 'N' bit set, we should send an event to user space to indicate that there has been a media change. This will be done via the scsi device. Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12[libata] check for SATA async notify supportKristen Carlson Accardi
Check to see if an ATAPI device supports Asynchronous Notification. If so, enable it, if the host controller supports AN. Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12libata-link: add PMP linksTejun Heo
Add link->pmp, ap->nr_pmp_links, ap->pmp_link[], and implement/update link helpers. printk helpers are updated such that port and link are identifed as 'ataP:' if no PMP is attached, while device is identified as 'ataP.DD:'. If PMP is attached, they become 'ataP:', 'ataP.LL:' and 'ataP.LL' - ie. link and device are identified their PMP number. If PPM is attached (ap->nr_pmp_links != 0), ata_for_each_link() iterates over PMP links, while __ata_for_each_link() iterates over the host link + PMP links. If PMP is not attached (ap->nr_pmp_links == 0), both iterate over only the host link. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12libata-link: implement ata_link_abort()Tejun Heo
Implement ata_link_abort(). Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12libata-link: make two port flags HRST_TO_RESUME and SKIP_D2H_BSY link flagsTejun Heo
HRST_TO_RESUME and SKIP_D2H_BSY are link attributes. Move them to ata_link->flags. This will allow host and PMP links to have different attributes. ata_port_info->link_flags is added and used by LLDs to specify these flags during initialization. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12libata-link: linkify config/EH related functionsTejun Heo
Make the following functions deal with ata_link instead of ata_port. * ata_set_mode() * ata_eh_autopsy() and related functions * ata_eh_report() and related functions * suspend/resume related functions * ata_eh_recover() and related functions Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12libata-link: linkify resetTejun Heo
Make reset methods and related functions deal with ata_link instead of ata_port. * ata_do_reset() * ata_eh_reset() * all prereset/reset/postreset methods and related functions This patch introduces no behavior change. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12libata-link: linkify PHY-related functionsTejun Heo
Make the following PHY-related functions to deal with ata_link instead of ata_port. * sata_print_link_status() * sata_down_spd_limit() * ata_set_sata_spd_limit() and friends * sata_link_debounce/resume() * sata_scr_valid/read/write/write_flush() * ata_link_on/offline() This patch introduces no behavior change. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12libata-link: implement and use link/device iteratorsTejun Heo
Multiple links and different number of devices per link should be considered to iterate over links and devices. This patch implements and uses link and device iterators - ata_port_for_each_link() and ata_link_for_each_dev() - and ata_link_max_devices(). This change makes a lot of functions iterate over only possible devices instead of from dev 0 to dev ATA_MAX_DEVICES. All such changes have been examined and nothing should be broken. While at it, add a separating comment before device helpers to distinguish them better from link helpers and others. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12libata-link: introduce ata_linkTejun Heo
Introduce ata_link. It abstracts PHY and sits between ata_port and ata_device. This new level of abstraction is necessary to support SATA Port Multiplier, which basically adds a bunch of links (PHYs) to a ATA host port. Fields related to command execution, spd_limit and EH are per-link and thus moved to ata_link. This patch only defines the host link. Multiple link handling will be added later. Also, a lot of ap->link derefences are added but many of them will be removed as each part is converted to deal directly with ata_link instead of ata_port. This patch introduces no behavior change. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: James Bottomley <James.Bottomley@SteelEye.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-31libata: implement BROKEN_HPA horkage and apply it to affected drivesTejun Heo
Some drives choke on READ_NATIVE_MAX_ADDRESS[_EXT]. Implement ATA_HORKAGE_BROKEN_HPA and apply it to affected drives. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-24ata_piix: fix suspend/resume for some TOSHIBA laptopsTejun Heo
ACPI implementations in several TOSHIBA laptops are weird and burn cpu cycles for tens of seconds while trying to suspend if the PCI device for the ATA controller is disabled when the ACPI suspend is called. This patch uses DMI to match those machines and bypass device disable on those machines during suspend. As the device needs to be put into enabled state on resume without affecting PCI enable count, matching resume callback uses __pci_reenable_device(). This bug is reported in bugzilla bug 7780. http://bugzilla.kernel.org/show_bug.cgi?id=7780 Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-22Merge master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6Linus Torvalds
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (60 commits) [SCSI] libsas: make ATA functions selectable by a config option [SCSI] bsg: unexport sg v3 helper functions [SCSI] bsg: fix bsg_unregister_queue [SCSI] bsg: make class backlinks [SCSI] 3w-9xxx: add support for 9690SA [SCSI] bsg: fix bsg_register_queue error path [SCSI] ESP: Increase ESP_BUS_TIMEOUT to 275. [SCSI] libsas: fix scr_read/write users and update the libata documentation [SCSI] mpt fusion: update Kconfig help [SCSI] scsi_transport_sas: add destructor for bsg [SCSI] iscsi_tcp: buggered kmalloc() [SCSI] qla2xxx: Update version number to 8.02.00-k2. [SCSI] qla2xxx: Add ISP25XX support. [SCSI] qla2xxx: Use pci_try_set_mwi(). [SCSI] qla2xxx: Use PCI-X/PCI-Express read control interfaces. [SCSI] qla2xxx: Re-factor isp_operations to static structures. [SCSI] qla2xxx: Validate mid-layer 'underflow' during check-condition handling. [SCSI] qla2xxx: Correct setting of 'current' and 'supported' speeds during FDMI registration. [SCSI] qla2xxx: Generalize iIDMA support. [SCSI] qla2xxx: Generalize FW-Interface-2 support. ...
2007-07-20libata: implement EH fast drainTejun Heo
In most cases, when EH is scheduled, all in-flight commands are aborted causing EH to kick in immediately. However, in some cases (especially with PMP), it's unclear which commands are affected by the error condition and although aborting all in-flight commands work, it isn't optimal and may cause unnecessary disruption. On the other hand, waiting for in-flight commands to drain themselves can take up to 30seconds. This patch implements EH fast drain to handle such situations. It gives in-flight commands some time to finish up but doesn't wait for too long. After EH is scheduled, fast drain timer is started and if no other completion occurs in ATA_EH_FASTDRAIN_INTERVAL all in-flight commands are aborted. If any completion occurred in the interval, the port is given another interval to finish up itself. Currently ATA_EH_FASTDRAIN_INTERVAL is 3 secs which should be enough for finishing up most commands. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-20libata: reorganize ata_ehi_hotplugged()Tejun Heo
__ata_ehi_hotplugged() now has no users. Regorganize ata_ehi_hotplugged() such that a new function ata_ehi_schedule_probe() deals with scheduling probing. ata_ehi_hotplugged() calls it and additionally marks hotplug specific flags. ata_ehi_schedule_probe() will be used laster. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-20libata: improve SATA PHY speed down logicTejun Heo
sata_down_spd_limit() first reads the current SPD from SStatus and limit the speed to the lower one of one below the current limit or one below the current SPD in SStatus. SPD may not be accessible or valid when SPD down is requested making sata_down_spd_limit() fail when it's most needed. This patch makes the current SPD cached after each successful reset and forces GEN I speed (1.5Gbps) if neither of SStatus or the cached value is valid, so sata_down_spd_limit() is now guaranteed to lower the speed limit if lower speed is available. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-20libata: make ->scr_read/write callbacks return error codeTejun Heo
Convert ->scr_read/write callbacks to return error code to better indicate failure. This will help handling of SCR_NOTIFICATION. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-20libata: implement AC_ERR_NCQTejun Heo
When an NCQ command fails, all commands in flight are aborted and the offending one is reported using log page 10h. Depending on controller characteristics and LLD implementation, all commands may appear as having a device error due to shared TF status making it hard to determine what's actually going on. This patch adds AC_ERR_NCQ, marks the command reported by log page 10h with it and print extra "<F>" after the error report for the command to help distinguishing the offending command. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-20libata: improve EH report formattingTejun Heo
Requiring LLDs to format multiple error description messages properly doesn't work too well. Help LLDs a bit by making ata_ehi_push_desc() insert ", " on each invocation. __ata_ehi_push_desc() is the raw version without the automatic separator. While at it, make ehi_desc interface proper functions instead of macros. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>